REPAIR REPLACEMENT TO JOINERY WORKS FALSE CEILING, FLOORING, WALL TILLING, BRICK WORK, PLASTERING, PLINTH PROTECTION AND OTHER CONNECTED WORKS FOR THE BUILDINGS OF AREA A AT NAVAL DOCKYARD VISAKHAPATNAM UNDER GE(I) DM VISAKHAPATNAM

Amount

Taking down chowkats or frames with shutter (without taking off shutter from the frames) n.exc 1.50 Sqm each complete all as specified and directed.

Taking down chowkats or frames with shutter (without taking off shutter from the frames) exc. 1.50 Sqm n.exc 4 Sqm each complete all as specified and directed.

Taking down shutters of any description exc 1 Sqm but n.exc 2 Sqm each complete all as specified and directed.

Taking down shutters of any description exc 2 Sqm each complete all as specified and directed.

S&F 2nd class hardwood plain solid, straight chowkat and frames, wrought, framed rebated on the solid, rounded or chamfered put together with glue pinned at joints complete all as specified and directed.

S&F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

M&L PCC 1:2:4 type B1(20 mm graded stone aggregate) as in bed block for embedding hold fast of doors, window frames or chowkats including necessary form work complete all as all as specified directed.

M&L for preparing surfaces of wood and wood based materials, steel and iron work, new or old, of any description and girth, not otherwise described, and treated with tar or coal tar black paint complete all as specified and as directed.

S&F 35 mm thick flush shutters solid core construction, with particle board core and ply wood face panels commercial type on both sides complete all as specified and as directed. Note :- The rate for flush shutters include for provision of suitable blocks for taking mortice locks, latches or other fittings complete.

S&F 2nd class hard wood small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary labours, articles n. exc 200 Cucm each complete all as specified and directed.

S&F factory made solid PVC door Frame of size 50 mmx47 mm made out of 5mm thick plain colour PVC sheet reinforced M.S. square tube, supplying & fixing in opening as per specification & drawing on page no. 178 of SSR Part -II complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. square tube for top and bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip 20 mm wide stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in M.S. frame welded /sealed to the stiles and rails with suitable sheet beading, and jointed together with solvent cement, supplying & fixing in the frame at site as per specification and drawing of page no 174 of SSR Part -II complete all as specified and directed.

Supply only MS butt hinges medium weight cold rolled 75 mm size all as specified and directed.

S&F MS butt hinges medium weight cold rolled of size 100 mm complete all as specified and as directed.

S&F 250 mm long aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as directed.

S&F 150 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed.

S&F Extruded aluminium alloy handles 125 mm long fabricated type anodised complete all as specified and directed .

S&F Extruded aluminium alloy handles 150 mm long fabricated type anodised complete all as specified and directed .

S&F 150 mm SS handles cast type polished bright complete all as specified and directed.

Taking up or down 15 mm bore steel water tubing and connections including cleaning for refixing or removal complete all as specified and directed.

S&F 15 mm dia (outer diameter of the pipe) Unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe complete all as specified and directed.

Supply and fix in repairs door closer hydraulically regulated designation No. 3 universal type aluminium body, (diecast) suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and directed

S&F in repairs floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor overall length of cover plate 150 mm complete all as specified directed.

S&F in repairs 100 mm SS handles cast type polished bright complete all as specified and directed .

S&F in repairs 250 mm long aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F heavy duty floor door spring including cutting hole into the floor and packing for making good with the existing floor complete all as specified and directed including taking out old one.

M&L for preparation of new or previously untreated wooden surface of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for Preparation of old wooden surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint all as specified and directed.

M&L Veneered decorative plywood 4mm thick, grade 1 (with BWR resin) with decorative face veneers on one face, fixed with screws to timber frame work or fixed with adhesive ( Fevicol) complete all as specified and directed including taking out old one..

M&L for french polishing on wooden surfaces of any description, width or girth including cleaning and preparing the surfaces including a coat of wooden filler on new works with two or more coats complete all as specified and directed.

Supply & Fix powder coated Aluminium window frame 2/3 track outer frame 92 mm x 31.75 mm x1.50 mm and guide rail of section Nos size 92 x 31.75 x1.50mm and shutter section 40 x 18 x 1.550 mm sliding type including necessary jointing cleats, glazing clips, rubber packing handles and anodised aluminium snab beading screws etc., complete all as specified and as directed

S&F in repair anodised aluminium grill, having mess size 100mmx100mm made out 6mm wide & 3mm thick aluminium section complete all as specified and directed.

S&F aluminium door shutter with chowkats made out of hollow aluminium sections as mentioned below, each shutter having 2 Nos ‘D’ type aluminium handles of 200mm long 2 Nos aluminium tower bolts of 150 mm long and 1 No brass mortice lock of 6 lever with key in duplicate. Shutter shall be partly glazed with 5 mm thick sheet glass ordianry quality and partly panelled with 12mm thick particle board, pre-laminated interior grade, prelaminated one side with decorative choice lamination, on other side balancing light grey lamination fixed with glazing clips, rubber beadings and aluminium beadings complete all as specified and directed. Chowkat size : 101.60 x 44.45 x 2.40 mm (1.608 Kg/RM appx) Shutter Top rail : 114.30 x 2.15 mm thick (1.836 Kg/RM appx) Bottom rail: 150.00 x 2.20mm thick (2.376 Kg/RM appx) Middle rail : 83.50 x 1.70 mm thick (1.243 Kg/RM appx) Vertical rail : 85.00 x 1.80 mm thick (1.302 Kg/RM appx)

Taking down aluminnium shutters of windows, ventilators etc of any description not exc 1 Sqm each and refixing the same in the same opening after replacing of unserviceable screws, cleat, rubber packing, aluminum snap beading etc, and tightening complete all as specified and directed ( Note:- 1.. Quted rate is inclusive cost of rubber beading, aluminum snap beading, screws, cleat etc whatever requires at site)

Taking down aluminnium shutters of doors, windows of any description exc 1 Sqm but not exceeding 2 sqm each and refixing the same in the same opening after replacing of unserviceable screws, cleat, rubber packing, aluminum snap beading etc, and tightening complete all as specified and directed. Note:- . Quoted rate is inclusive cost of rubber beading, aluminum snap beading, screws, cleat etc whatever requires at site)

Dismantling of Wall and ceiling boards/ wall partition (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets / aluminium frame work complete all as specified and directed.

M&L for partition walls with panels of 1.44 sqm (appx.) made out of aluminium anodised hollow sections of size 63.50x38.10x1.95mm thick ,snap grid beading, rubber gasket, 5 mm thick sheet glass and 12mm thick prelaminated particle board interior grade, prelaminated one side with decorative choice lamination, on other side balancing light grey lamination fixed with aluminium beadings complete all as specified and directed. Note :- The scope work incude for taking down existing damaged aluminium door/ window/grill/panels and the unit rate quoted shall be deemed to include for the same.

S&F Anodised Aluminium Frame Work (snap grid) for false ceiling Work made from Anodised Aluminium main /cross tee of size not less than 38 mm x 24 mm x 1.5 mm thick and 28 mm x 24 mm x 1.5 mm thick respectively for false ceiling of grid size 600 mm x 600 mm including necessary hanging arrangement comprising of 6 mm dia MS rod, 'J' bolts with necessary bolts, nuts and washer all as per manufacturer's instruction. The snap grid (main & cross section) shall be supported at ends all along the wall with Anodised Aluminium angle of size 40mmx25mmx2mm, weighing 0.36 Kg / RM. The main and cross tees shall be jointed at junction / crossings with anodized aluminium angle bracket of size 15mmxl5mmx1.5mm, weighing 0.12 Kg per running metre, fixed with suitable size mild steel, bolts nuts and washers complete as per manufacturer's instruction and as specified and directed.

S&F 6mm thick perforated particle board 60cm x60 cm in size for insulation and acoustic purposefixed with aluminium frame work in ceiling with screws or with staples on snap grid as per manufacturer's instruction complete all as specified and as directed.

Dismantling wrought iron or MS work of any description not otherwise provided, complete all as specified and directed.

S&F M.S. framed work such as grills gratings etc with end of bars shouldered/or riveted or forged into spikes framed guard bar, barred iron doors, ladders, framed balusters, walkways, railing, frame work of water tanks and similar works steel quality conforming to Fe-290, Grade E- 165 complete all as specified directed .

M&L preparation of new or previously untreated steel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

M&L preparation of old painted steel surface over 10 cm width or girth not otherwise described and applying a coat of synthetic enamel paint complete all as specified and directed

Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed.

M&L for pre-cast cement concrete 1:3:6 type C1(using 20 mm graded crushedstone aggregate) block masonry with solid blocks, exc. 10 cm in width and setting in cement mortar (1:6) complete all as specified and directed.

Demolition of cement concrete( un reinforced) in ground floors and paving n exc 15 cm thickness (below or above ground level) including removing debris out side ND(V) complete all as specified and directed.

M&L for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and including cement screed 15 mm thick in 1:4 complete all as specified and directed.

M&L PCC 1:2:4 type B1 type (using 20 mm graded crushed stone aggregate) as in foundation filling and mass concrete etc complete all as specified and directed.

M&L 75 mm thick cement concrete 1:3:6 Type C2 (using 40 mm graded crushed stone aggregate) in floors (plinth protection) finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed.

Taking down cement plaster on brick or concrete wall etc including racking out joint hacking for key, scrubbing down with water etc. complete all as specified and as directed.

M&L rendering 10 mm thick in CM 1:4 on brick/concrete wall surfaces of any description, and finishing the surfaces even and smooth without using extra cement all as specified and directed.

M&L rendering 15 mm thick in CM 1:4 on brick/concrete wall surfaces of any description, and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L 10 mm thick plastering in cement mortar 1:3 on concrete surfaces of ceiling and finishing the surfaces fair and even without using extra cement all as specified and directed.

M&L for preparing newly plastered and unplastered surfaces of ceiling and applying three coats of white washing complete all as specified and directed.

M&L for preparing new surfaces of walls and applying two coats of oil emulsion distemper over a coat of alkali resistant primer complete all as specified and directed.

M & L for preparation of newly plastered surfaces of walls and applying two coats of exterior emulsion paint (weather coat) over a coat of alkali resistance primer complete all as specified and directed.

M & L for preparation of newly plastered surfaces of walls and applying two coats of exterior emulsion paint (weather coat) over a coat of alkali resistance primer over a coat of cement based wall putty minimun thickness 1.5mm and cutting to smooth surfaces by sand paper complete all as specified and directed.

Complete removal of existing treatment of old decorated surfaces of walls and applying two coats of exterior emulsion paint (weather coat) over a coat of alkali resistance primer complete all as specified & directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises all as specified and directed.

M&L for 25 mm thick PCC (1:2:4) type B0 (using 12.5 mm graded crushed stone aggregate) as in floor and finishing the surfaces fair and even without using extra cement all as specified and directed

Material & Labour for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed inneat cement slurry and pointed in white or coloured cement to match laid over and including cement screed 10 mm thick in 1:4 complete all as specified and as directed.

Material & Labour for coloured glazed ceramic tiles (300 x 450) x 7-8 mm thick in dado set and jointed in neat cement slurry and pointed in coloured cement to match fixed over & including rendering in CM 1:3, 10 mm thick complete all as specified and as directed.

M&L for light shed vitrified ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick 1:6 cement morter including roughning surface of old concrete floor by picking sweeping clean and washing down with water to remove dust and brushing neat cement slurry with 3 kg of cement per sqm complete all as specified and as directed

M&L light shade vitrified ceramic tiles 10 mm thick (square/ rectangular) polished as in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10 mm thick 1:4 cement morter complete all as specified and as directed

M&L Granite (of any type) slab, 18 to 20 mm thick machine cut in skirting/dado laid over 15 mm thick cement screed (1:4) and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of the granite stone including cutting and polishing complete all as specified and directed

Material & labour for rounding to edges of granite stone slabs one edge such as in counter type WHB platform etc., complete all as specified and as directed.

M&L for decorative (Endura tiles / stair tiles) 7 to 8 mm thickas in treads / rise / landing of stair laid over 15 mm thick cement screed (1:6) and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of the tiles complete all as specified and directed.

M&L for hacking old broken glass of any thickness, size, quality and description and fixing new rough cast wired glass, 6.4mm thickness and glazing with adhesive on vertical shop wall cladding glazing exceeding 0.25 Sqm and not exceeding 2.0 Sqm in each panel of the work shop buildings at any height of 6m to 20 M fixed in position complete.

S&F factory made UPVC white colour sliding window three track of area not exceeding 2.00 sqm each made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67 mm). Sliding mesh Sash (42mm x 57mm) sliding interlock (one vertical lenght in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2 + - 0.2mm thick galvanised steel frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware (Touch Lock of zinc alloyed (white powder coated ), steel roller system, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. Note: the unit rate quoted by the contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.

S&F in repair for stainless steel (Grade 304) of railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specfied and directed.

S&F coloured tinted glass 4.0 mm thick ordinary quality fixed with aluminium/PVC/wooden beads in squares/rectangular shape as fit in existing shutters/frame work of area exc 0.5 sqm but n.exc 2 sqm complete all as specified and directed.

S&F in repair stainless steel wire cloth 0.36 mm nominal dia or wire and average width of aperture 1.40 mm and fixed with tinned tacks or stainless steel wire staple complete all as specified and directed

Refixing ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets including taking down the same complete all as specified and directed.

M&L for cement concrete type D2, 1:4:8 (using 40mm graded stone aggregate) as in foundation filling & mass concrete all as specified and directed.

SINGH BUILDERS

sai ganesh enterprises

bhavani constructions

SRI SIMHADRI COMPANY

BSA INFRA