Construction of Skill Development Centre building at Ghumarwin District Bilaspur HP including internal external water supply sanitary installation development of site construction of 10000 liters capacity rain water harvesting tank and Co 100 users

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (up to all width), including dressing of sides and ramming of bottoms,up to all lift, including getting out the excavated soil and disposal of surplus excavated soil all lead and lifts as directed by the Engineer-in- charge. All kinds of soil

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand) : 8 graded stone aggregate 40 mm nominal size) including carriage of material in all leads and lifts.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:5:10 (1 Cement : 5 coarse sand) : 10 graded stone aggregate 40 mm nominal size) including carriage of material in all leads and lifts.

Centering and shuttering including strutting, propping etc. and removal of form for : including carriage of material in all leads and lifts.

Providing and laying vitrified floor tiles as per sample approved by the Engineer-in- Charge in different sizes (thickness not less then 10 mm) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete including carriage of material in all leads and lifts.

Providing and laying vitrified floor tiles matt finish as per sample approved by the Engineer-in- Charge in different sizes (thickness not less then 10 mm) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete including carriage of material in all leads and lifts.

Edges of slabs and breaks in floors and walls Under 20 cm wide

Providing and laying 1:1.5:3 excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.

All works upto plinth level

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more including carriage of material in all leads and lifts.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in cement mortar 1:6 (1 cement : 6 coarse sand) including carriage of material in all leads and lifts.

Providing and laying autoclaved aerated cement blocks masonry with 150mm/ 230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately) including carriage of material in all leads and lifts.

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with Cement mortar 1:6 (1 cement : 6 coarse sand) including carriage of material in all leads and lifts.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.including carriage of material in all leads and lifts

Granite of any colour and shade (i) Area of slab over 0.50 sqm.

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.including carriage of material in all leads and lifts. (a) Granite work.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in- charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) including carriage of material in all leads & lifts.

Providing and laying Vitrified tiles as per sample approved by the Engineer-in- Charge in different sizes (thickness not less then 10 mm), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. including carriage of material in all leads and lifts.

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge including carriage of material in all leads & lifts.

Providing and fixing 10mm thick anti skid water proof stain and impect resistent heavy duty vetrified tiles any size/colour manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete including carriage of material in all leads & lifts.

Digital tiles in skirting risers of steps and dado in any size/colour 12 mm thick cement mortar 1:3 (1 cement :3 sand) and jointed with cement slurry including carriage of material in all leads and lifts

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required including carriage of material in all leads and lifts.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes including carriage of material in all leads and lifts 110 mm diameter

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.including carriage of material in all leads and lifts:-110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion including carriage of material in all leads and lifts

Coupler 110 mm

Bend 87.5° 110 mm bend

Shoe (Plain) 110 mm Shoe

6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand) including carriage of material in all leads and lifts

CEMENT PLASTER (IN FINE SAND) 15 mm cement plaster on the rough side of single or half brick wall of mix including carriage of material in all leads and lifts

Cement mortar 1 : 3 (1 cement : 3 fine sand)

Cement mortar 1 : 6 (1 cement : 6 fine sand)

CEMENT PLASTER (IN FINE SAND) 20 mm cement plaster of mix Cement mortar 1 : 6 (1 cement : 6 fine sand) including carriage of material in all leads and lifts

Applying priming coat with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works including carriage of material in all leads and lifts

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications (a) Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture including carriage of material in all leads and lifts.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete including carriage of material in all leads and lifts.

Wall painting (Two coats) with plastic emulsion paint of approved brand and manufacture on undecorated wall surfaces to given an even shade including thoroughly brushing the surface free from mortar droppings and other foreign matter and sand prepared smooth including applying of putty as required for making the surface including carriage of material in all leads and lifts.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm including carriage of material in all leads and lifts

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth including carriage of material in all leads and lifts.

Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand) including carriage of material in all leads and lifts.

Constructing Course rubble hammer dressed 'U' shape open surface drain with side wall.15x22 cm in cement mortar 1:6 (1 Cement : 6 Sand) and inside plastring with cement plaster 1:3 (1 Cement:3 Sand) including earth work and laying 10 cm cement concrete in 1:5:10 (1 Cement : 5 Sand : 10 graded stone aggregate) of 40 mm nominal size) and 7.5 cm cement concrete 1:2:4 (1 Cement : 2 Sand : 4 Graded stone aggregate of 20 mm nominal size) and finished with a floating coat of neat cement complete as per standard design.) including carriage of material in all leads and lifts.

Making chases up to 7.5x7.5 cm in walls for G.I. pipe and filling the same with cement concrete 1:3:6 ( 1 cement: 3 Sand: 6 graded stone aggregate 20 mm down gauge )and finishing with matching surface after housing G.I. pipe etc. including carriage of material in all leads and lifts.

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in- Charge. 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern. including carriage of material in all leads and lifts.

Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade including carriage of material in all leads and lifts.(a) Two or more coats on new work.

Providing plaster drip course/ groove in plastered surface or moulding to R.C.C. projections including carriage of material in all leds and lifts.

Providing and laying cement concrete 1 : 8 : 16 (1 cement : 8 sand : 16 graded stone aggregate 20 mm nominal size) and curing complete on slab and floor excluding cost of form work screed laid under flooring including carriage of mterial on all leads and lifts.

62 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture’s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete including carriage of material in all leads and lifts.

50 mm thick cement concrete flooring 1:2:4(1 cement:2sand:4gradedstone aggregate 20mm nominal size) laid in one layer finished with a floating coat of neat cement,including carriage of material in all leads and lifts.

Providing and fixing of 4mm thick HPL clading (Tmmex exterior or equivalent) to be provided in external face complete as per archtectural drawings including carriage of material in all leads and lifts.

Providing and Fixing ‘APHONY FIBRETTE ‘ tiles made of Wood Fibre 1mm width cement composites 15mm thick with an option of colours as per the choice of the Architect/ perso

n in charge of size 595x595 mm . Has excellent noise absorption of 1 NRC as per ISO: 354-1985 and ASTM 423-90 a, Density 400 Kg/ m3, meets stringent Fire Ratings ASTMD-876 and Fire Class -1 as per BS 476 part 5 and 6,Class P-not easily ignitable as per BS-476-Part 5 (Ignitability for material). This is applicable for core and class 1 as per BS 476-Part 7 (Method for classification of surface spread of flame) , weather resistance as per IS 3308, Thermal Insulation as per IS:3346-1980 with relative humidity of 90% RH at 60o Celsius(140o Fahrenheit) for 15 days= No deterioration. Conforms to En 131682001 and are RoHS Complaint. Can be installed on T24 grid system of 0.6mm thick Main ‘T’ length minimum 3000mm, web minimum 35mm to be placed at 600mm centre to centre and secondary cross ‘T’ of length 600mm web minimum 35mm inter locked, Wire Support for Main T to be taken at every 1200mm length wise and 600mm width wise, Specially designed for Acoustic Vibration management and long life with a backing of HIMALYAN ACOUSTICS 50mm 1000 GSM thick absorb wool tested as per Fire including carriage of material in all leads and lifts.

Providing and Fixing factory made uPVC door frame, made of uPVC exturded sections, of size 65 mm x 55 mm with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be mitred cut and jointed with plastic brackets and stainless steel screws, reinforcing hinge side vertical of the frames with PVC profile of Size 28 mm x 30 mm having wall thickness 2 mm (±0.2 mm), including providing & fixing 3 nos of 125 mm long stainless steel hinges to the frame, fixing the frame with jamb with required number & size of anchor dash fastners, all complete as per manufacturer's specification and direction of Engineer-in-charge

Providing and fixing 37 mm thick factory made PVC door shutter, styles and rails made of PVC hollow section of size 100 mm x 37 mm with wall thickness 2 mm (± 0.2 mm), with inbuilt bead on one side, styles and rails mitered cut and joint at the corners by means of 2 nos of plastic brackets of size 75 mm x 220 mm at each corner and stainless steel screws, reinforcing the hinge side of style by inserting PVC profile of size 28 mm x 30 mm, with wall thickness 2 mm ( ± 0.2 mm). Lockrail of size 100 mm x 37 mm, wall thickness 2 mm (+ 0.2 mm) will be fixed to the vertical styles. Providing with PVC snapfit beads and panel of size 100 mm x 20 mm, and inserting 2 nos tie bar of 6 mm dia and fastening with nuts and washers complete, all as per manufacturer's specification and direction of Engineer-in-charge

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in- Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made including carriage of material in all leads and lifts. (a) Three track three panels sliding window made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm)

Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings, the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). including carriage of material in all leads & lifts.

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (a) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement. including carriage of material in all leads & lifts.

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes testing of joints complete as per direction of the Engineer in charge. INTERNAL WORK - EXPOSED ON WALL including carriage of material in all leads and lifts.

1216 (16 mm OD) pipe

1220 (20 mm OD) pipe

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work including carri

age of material in all leads and lifts.

15mm dia nominal bore

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete including carriage of material in all leads and lifts:-25 to 40 mm nominal bore

Providing and fixing PVC water storage tank of ISI : 12701 marked, G.I. inlet and outlet connection, 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground level including carriage of material in all leads and lifts:-1000 litres net capacity tank.

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete including carriage of material in all leads and lifts.

110 mm dia.

75 mm dia.

Providing and fixing PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. complete including carriage of material in all leads and lifts.

110 mm dia

75 mm dia

Providing and fixing PVC door bend with oval access door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete. including carriage of material in all leads and lifts.

110 mm dia

75 mm dia.

Providing and fixing PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. complete including carriage of material in all leads and lifts.

75 mm dia

75 mm dia

Providing and fixing PVC door bend with oval access door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete. including carriage of material in all leads and lifts.

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete including carriage of material in all leads and lifts.

75 mm dia.

Providing and fixing PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. complete including carriage of material in all leads and lifts.

Providing and fixing PVC single equal branch with ovel access door, ISI marked insertion rubber washer 3mm thick bolts and nutscomplete including fixing with approved adhsive etc. complete including carriage of material in all leads and lifts.

75 mm dia.

Providing and fixing PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. complete including carriage of material in all leads and lifts.

Providing and fixing PVC collers ISI marked of approved design fixing with approved adhesive etc. complete including carriage of material in all leads and lifts.

Providing and fixing PVC Cowl ISI marked of approved design fixing with approved adhesive etc. complete including carriage of material in all leads and lifts.

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete including carriage of material in all leads and lifts:-110 mm X 75 mm.

Fixing vitreous china wash down water closet (European type WC pan) with intergal "P" or "S" trap including jointing the trap with soil pipe in cement mortar 1:1 ( 1 cement :1 sand)Plastic seat and cover to be measured and paid for seperately :- Ordinary closet. (L.R.)

Fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm P.V.C. P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required (a) White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests. (L.R.)

Fixing PTMT Coloured / white high density polythelene / poly propylene 10 litres capacity ( full flush) European standard control low level flushing cistern with fittings with a pair of brackets with fittings such as lead valve, syphon, 15mm nominal size PVC ball valve with polythene float,with push button,couplings for connections with inlet, outlet and ovrflow pipe, 40mm dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow) pipe to be measured and paid for separately (L.R.)

Fixing plastic seat (solid / Holow type) and cover for wash down water closet with C.P. Brass hinges and rubber buffers. (i) Solid type: (a) White plastic seat and cover (L.R.)

Fixing PTMT jet spray of approved quality with 1.5 mtr. tube. (L.R.)

Fixing stainless steel kitchen sink of approved standard ISI make with drain board and C.P. waste with with C.I. or M.S. Brackets painted white including cutting holes and making good the same but excluding fitting.(i) 610mmx510mm with bowl depth 200 mm. (L.R.)

Fixing vitreous china wash basin with single/double hole for pillar tap with C.I. Or M.S brackets painted white including cutting holes and making good the same but excluding fittings (L.R.).

Circular (i) 560mmx400mm oval type under counter.

Fixing vitreous china padestal for wash basin complete recessed at the back for the reception of pipes and fittings (L.R.).

Fixing C.P. brass waste for wash basin or sink (a) 32mm dia. (L.R.)

Fixing 100 mm dia cromium plated stainless steel grating . (L.R.)

Fixing of G.I. Union for wash basin or sink 32 mm dia. (L.R.)

Fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P brass screws and washers complete. (L.R.)

Fixing 600mmx120mm glass shelf with C.P brass brackets and guard rail complet fixed to wooden plugs with C.P Brass screws (L.R.)

Fixing 750mmx20mm size C.P Brass towel rail complete with C.P Brass brackets fixed to wooden plugs with C.P brass screws (L.R.) .

Fixing C.P. brass towel ring complete fixed on wall face with concealed fittings arrangement (L.R.)

Fixing C.P. brass soap dish with C.P.brass brackets fixed to wooden plugs with C.P. brass screws (L.R.)

Fixing 15mm dia C.P. brass bib tap with capstan head . (L.R.)

Fixing C.P. Brass shower rose with 15mm or 20mm inlet 150 mm dia (L.R.)

Providing and fixing brass angle valve 15mm without nuts and pipe including carriage of material in all leads and lifts.(ESS-ESS/CZAR/NOVA)

Providing and fixing brass full way value with wheel (confirming to BIS Specifications) including carriage of material in all leads & lifts. (ESS-ESS/CZAR/NOVA)

15mm nominal bore.

20 mm nominal bore.

Providing and fixing G.I./M.I. Union of following sizes (where not included in the item) (confirming to BIS Specifications) including carriage of material in all leads & lifts. (ESS-ESS/CZAR/NOVA)

ll leads and lifts.

Fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete (L.R.)

Providing and fixing stone ware gully trap grade 'A' complete with C.I. Grating, brick masonary chamber in cement mortar 1:5 and water tight C.I. Cover with frame of 300mmx300mm size (inside)the weight of cover to be not less than 4.53 kg and frame tobe not less than 2.72 kg. including carriage of material in all lead and lifts. (I) 1 square mouth traps (i) 100mmx100mm (P-Type). (L.R.)

Cutting holes through existing brick/stone work including making good the same in cement mortar 1:6( 1cement:6 sand) per cms. Depth of cutting including carriage of material in all leads and lifts(i) Holes up to and including 400 sqcm in area (L.R.)

Fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required (a) Range of two urinal basins with 5 litre white P.V.C. automatic flushing cistern (L.R.)

Fixing vitreous china division plate for urinals 600mmx330mm size (L.R.)

Fixing 15mm dia C.P. brass pillar tap with capstan head (L.R.).

Constructing manhole with RCC top slab in 1:2:4 mixure (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) foundation concrete 1:4:8 ( 1 cement : 4 sand : 8 graded stone aggregate 40mm nominal size) inside plastering 15mm thick with cement mortar 1:3 (1 cement : 3 sand finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) finished smooth complete including curing and testing. including carriage of material in all leads and lifts.

Inside size 800x800mm and 500mm deep including SFRC Cover with frame (medium duty) total weight of cover and frame to be not less than 173 kg (weight of cover

103kg on and weight of frame 70 kg With 230 mm walls of brick masonary using common burnt clay building bricks in cement mortar 1:3 (1 cement : 3 sand)

Constructing soak pit 2.5 metre diametre 3.00 metre deep with45x45cm dry brick honey comb shaft with bricks of class designation 75 and soil waste drain pipe 100mm diameter 1.80 metre long as per standard design with F.P.S. including carriage of material in all leads and lifts.

Providing and fixing 200 mm wide cast iron rungs with cheque-red or ribbeed non slip surface including fixing in manholes with 200 mm x 200 mm x 100 mm cement concrete 1:3:6 (1cement : 3sand : 6 graded stone agg. 20 mm nominal size) including carriage of materials in all leads and lifts.

Supplying and fixing cast iron cover with frame for manhole of 500mm internal diameter C.I. cover (medium duty) the weight of cover to be not less than 58 kg including carriage of material in all leads and lifts