SPECIAL REPAIRS TO BUILDING NO. P-77 (R BLOCK) IN PHASE II RESIDENTIAL AREA UNDER SPECIAL REPAIRS B/R AT NAVAL STATION BHEEMUNIPATNAM, AS AND AS TO STATIC WATER TANK NOS 3, 4 AND 5 AT NAD BHEEMUNIPATNAM UNDER GE (P) NAVY KALINGA

Amount

Taking down Chowkhats or frames not exc. 1.5 sq. m each with shutters (without taking off shutters from the frames)

Taking down Chowkhats or frames exc. 1.5 sq. m but n exc 4.0 Sqm each with shutters (without taking off shutters from the frames)

Demolition of Unreinforced Cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level

Demolition of Unreinforced Cement Concrete in ground floors and pavings n exc 15 cm thickness BUT

Demolition floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

Demolition of brickwork built in cement mortar

Dismantling of RCC Jally ,Trellis work (Jafri), including taking as under of battens in trellis (posts and rails measured separately) one way

S&F Second class hard wood Plain solid straight chowkhats and frames,wrought ,framed, rebated on the solid,rounded or chamfered ,put together with glue pinned at joints complete

M&L for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius with built in CM 1:6

S&F Flush shutters 30 mm thick, solid core construction, with block board core and ply wood face panels, commercial type on both sides complete.

S&F 35mm thick IInd class HW Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (with sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a);

M&L for Preparation of new wooden surfaces and applying two coats of synthetic enamel paint over a coat of pink primer on surfaces of wood of any description over 10 cm in width or girth not other wise described complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded wood grain printed PVC sheet & 5mm thick x 15mm wide PVC sheed beading used insied Stiles and Rails and decorative PVC beading of 10mm x 10mm (90*) used instead of exposed portion of PVC sheet beading and the paneeling of wood grain printed PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing

S&F Solid PVC Door Frame of size 100mm x 60mm made out of 5mm WOOD GRAIN printed PVC sheet used instead of plain colour PVC sheet ans edges will be painted to match with printed sheet, reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

S&F 125 mm Butt hinges, Medium weight, cold rolled mild steel.

S&F 100 mm Butt hinges, Medium weight, cold rolled mild steel

S&F 200mm Aluminium anodised,barrel tower bolts of extruded section

S&F 150 mm Aluminium anodised,barrel tower bolts of extruded section.

S&F Aluminium handles, cast type,anodised of size 150 mm.

S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy.

S&F Steel (white powder coated) crescent lock for UPVC sliding window/door with necessary screws etc complete.

S&F 5mm thick plain glass and square exc. 0.5 Sq.m. in each pane fixed to PVC/UPVC frame work complete.

S&F UPVC window,(unplastisized poly-Vinyl Chloride) sliding windows multi-chambered and stiffened framed windows using 88mm x 52mm size sections all-round as main frames and shutters made with profile sections of size 57mm x 42mm, including the cost and fixing of 5mm thick clear float glass in shutters and stainless steel wire mesh shutters shall have well defined welded corner joints without any gaps, fixed the window unit to the existing masonry with anchor fasteners as required. The shutters shall have necessary handles and other associated fittings to facilitate smooth operation. Both the frames and the shutters shall be reinforced with GI profiles of thickness 1.25mm the entire window is covered with MS powder coated tube of size 40mm x 20mm all-round the frame the frame section, 10mm square bars horizontally placed at 120mm C/C and suitably placed vertically to avoid buckling and providing structural strength, Minimum weight shall be 10kg/Sqm and fixed to UPVC frames with suitable fasteners. The gaps between the window frames and masonry walls shall be filled with silicon or with any other suitable filler materials complete all as specified and directed. Make : Rajshri Plastiwood/Veka/Sintex/Duroplast Extrusion Pvt. Ltd

S&F Powder coated Anodised aluminium frame for windows,doors and ventilators, including jointing cleat for fixing etc complete.

S&F Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples

S&F Powder coated Aluminium grill/Deco grill for Windows , Ventilators etc

S&F Sheet glass 4mm thick,Figured glass, pin head type in squares n exc 0.5 sq. m in each panepinheaded in louvers.

Providing and injecting chemical emulsion for Post constructional anti termite treatment along external wall below concrete apron using chemical emulsion @2.25 Ltrs/linear metre including drilling and plugging holes etc in apron.

S&F Treatment of soil under existing floor using emulsion @1litre per hole ,300mm apart including drilling and plugging 12mm dia holes withcement mortar 1:2 (1cement:2 coarse sand) to match the existing floors.

S&F Plain Cement concrete 25mm thick type B-0, 1:2:4 (12.50mm graded aggregate) in sub base.

S&F Providing joint free non skid coloured ceramic tiles 600 x 600 x 7 to 8 mm thick floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick cement screed bed in CM (1:6).

S&F Providing joint free non skid coloured ceramic tiles 600 x 600 x 7 to 8 mm thick in Skirting/Vertical Surface and jointed in neat cement slurry and pointed in white or colour cement to match for joint free over backing of 10 mm th CM1:4 on fair faces of brick work or concrete surfaces complete.

S&F Non skid/matt finish ceramic tiles 7 to 8 mm thick of size exc 0.11sqm but not exc 0.18sqm, in floors etc.set and jointed in neat slurry and pointed in white or coloured cement to match for joint free over Screed bed or bedding layer of mortar 15mm of thick CM 1:6 for laying floor finishes.

S&F Glazed ceramic coloured tiles 300 x 450x 6-7 mm thick as in verticle surface set & jointed in neat cement slurry & pointed with coloured cement to match over 10 mm thick rendering with CM 1:4.

Fixed in repairs vitreous China wash down water closet pan (pedestal pattern), white including fixing bolts, low level flushing cistern 10 ltr capacity and flush pipe and seat cover etc. Complete.

Fixed in repairs Wash hand basin of size 550x400 vitreous China (flat back or angle back type) including half pedestal and cutting for and pinning in ends of brackets or erecting stand including supply and fixing of waste coupling, waste pipe etc. complete.

Fixed in repairs PVC flexible connections 15mm size with PTMT nuts of length 600mm complete all as specified and as directed by the Engineer-in-Charge.

Fixed in repairsTubular towel rail, 20mm dia, Brass Chromium plated , 20mm dia., 60cm long between flanges complete all as specified and as directed by the Engineer-in-Charge.

Fixed in repairs Soap dish, chromium plated brass, of approximate size 160x160x90mm, fixed to plugs with chromium plated brass screws complete all as specified and as directed by the Engineer-in-Charge.

S&F 40mm dia. PVC waste pipes for WHB/sink fixed to walls including fittings and connecting to multiple floor trap complete.

S&F 50mm dia. PVC waste pipes for WHB/sink fixed to walls including fittings and connecting to multiple floor trap complete.

S&F PVC (SWR) pipes 110mm dia. single docketed in any length with rubber ring joints fixed to walls complete.

S&F PVC (SWR) pipes 75mm dia. single socketed in any length with rubber ring joints fixed to walls complete.

S&F 110mm dia. PVC (SWR) plain bends any radius complete.

S&F 75mm dia. PVC (SWR) plain bends any radius complete.

S&F 110mm dia. PVC (SWR) bends any radius provided with access door complete all as specified and directed by the Engineer-in-Charge.

S&F 75mm dia. PVC (SWR) bends any radius provided with access door complete all as specified and directed by the Engineer-in-Charge.

S&F 110mm dia. PVC (SWR) junction single (Single T) equal or unequal provided with access door complete all as specified and directed by the Engineer-in-Charge.

S&F 75mm dia. PVC (SWR) junction single (Single T) equal or unequal provided with access door complete all as specified and directed by the Engineer-in-Charge.

S&F PVC (SWR) vent cowls 110mm dia. complete all as specified and as directed by the Engineer-in-Charge.

S&F PVC (SWR) multi floor trap 75mm dia. outlet with grating including jointing with solvent cement complete all as specified and directed by the Engineer-in-Charge.

S&F in repairs, PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement complete all as specified and directed by the Engineer-in-Charge.

S&F grating doom 125mm dia. with waste hole of PTMT (Min weight 40 gms) complete all as specified and as directed by the Engineer-in-Charge.

M&L 100 mm Cast iron Nahani trap grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and as directed by the Engineer-in-Charge.

Taking down Roof WPT/Cement plaster on roof

M & L for Brushing neat cement slurry with 3.0kg of cement per sq. metre

M & L for Plain Cement concrete 40mm thick type B-1, 1:2:4 (20mm graded aggregate) in padding

M & L for Rendering 15mm thick with CM 1:3 with water proofing compound on fair faces of brick work or concrete surfaces, finished Fair & even (without using extra lime or cement) Note:WPC will be measured and Paid seperately

Supply only Integral Water Proofing Compound [ISI marked] of approved make.

M & L for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) and on primed surface by forced application an applying one coat of bituminious aluminium paint complete all as specified and directed.

S & F stainless steel pipe 25mm dia Curtain rod for Windows,doors opening etc

S & F Fancy type CP Knobs for fixing curtain rod all as directed and specified

M & L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in 20mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over a screed bed of 20mm thick in cement mortar 1:4

M & L for preparation of old surfaces and applying one of white wash on Ceiling surfaces

M&L Complete removal of existing treatment on wall and applying two coats of plastic emulsion paint over priming paint including applying 3mm thick wall care putty on walls.

S&F in repair 15mm dia. chromium plated with long shank and cup stop valves (concealed type), screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed by the Engineer-in-Charge.

S & F in repairs Brass chromium plated shower rose 125mm size

S & F in repairs Bib taps 15mm dia Fancy type Chromium Plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed

S & F in repairs Bib taps 15mm dia Fancy type Chromium Plated Flexible 360 Degree Swivel Kitchen Sink Faucet with Single Handle,Chrome Finish Make :CERA

S & F in repairs two way bib cock, CP, Fancy type - 15mm dia

S & F in repairs 15mm bore dia Pillar taps Fancy type,chromium plated, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed

S & F in repairs 15mm bore dia Stop valves fancy type Chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed

S & F Health Faucet for 15mm dia with 1.5m long easy flex tube in Chrome finish and wall look

M/L for Mild Steel TMT bars of 8mm dia and cut to length bent to shape required incl cranking ,bending and binding with and incl mild steel wire annealed not less than 0.9mm dia complete

Taking down cement plastering on brick or concrete wall ,including raking out joints,hacking for key,scrubbing down with water etc

M/L for rendering cement plaster 15 mm thick on fair faces wall in CM 1:4 finished even and smooth without using extra cement.

M&L for 10 mm thick rendering on Internal plaster of brick work or concrete surfaces in cement mortar 1:6 complete all as specified and directed

M & L for preparation of new surface of walls and applying two coats of Exterior emulsion over a coat of primer for external surface on walls complete all as specified and as directed by the Engineer-in-Charge.

M & L for Complete removal of existing surfaces of walls and applying Two coat of Exterior emulsion on walls complete all as specified and as directed by the Engineer-in-Charge.

M/L for rendering cement plaster 5 mm thick on fair faces of ceiling in CM 1:3 finished fair and even without using extra cement.

Provn of making hole in marble/granite slab of cooking plateforme for cooking gas pipe etc by means of drilling machine n.exc 25 mm dia all as directed by Engineer-in-Charge

Taking up or down 15mm bore, steel tubing and connection including cleaning for refixing or removal from site.

Taking up or down 20mm bore, steel tubing and connection including cleaning for refixing or removal from site.

Taking up or down 25mm bore, steel tubing and connection including cleaning for refixing or removal from site.

S & F in repairs 32mm bore dia PP-R Gate valves (brass insert) as per requirement of the site

S&F S&F sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm all as specified and as directed by the Engineer-in-Charge.

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised for 30 mm flaps

M&L for 75mm thick PCC 1:3:6 type C1 using 20 mm graded stone aggregate as in plinth protection , pavment surface finished even and smooth without using extra cement complete all as specified and directed.

S & F 20 mm outer dia, 3-layer PP-R P o l y p r o p y l e n e random copolymer) for concealed pipes SDR 7.4 (PN - 16) UV stablised and a n t i m i c r o b i a l fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded p o l y p r o p y l e n e random fittings fixed complete to walls, ceilings or in floors etc.

S & F 25 mm outer dia, 3-layer PP-R P o l y p r o p y l e n e random copolymer) for concealed pipes SDR 7.4 (PN - 16) UV stablised and a n t i m i c r o b i a l fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded p o l y p r o p y l e n e random fittings fixed complete to walls, ceilings or in floors etc.

S & F 32 mm outer dia, 3-layer PP-R P o l y p r o p y l e n e random copolymer) for concealed pipes SDR 7.4 (PN - 16) UV stablised and a n t i m i c r o b i a l fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded p o l y p r o p y l e n e random fittings fixed complete to walls, ceilings or in floors etc.

Dismantling water tanks capacity exc250 but not exc 500 Ltrs and removing to store

S & F 500 litres Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified and directed

S&F in repairs Veneered decorative 18 mm thick plywood, grade 1 (with BWR resin) with one face has decorative veneer; fixed with screws to timber frame work complete all as specified and directed by the Engineer-in-Charge.

M&L Preparation of new plastered wall surfaces and applying two coats of plastic emulsion paint over priming paint including applying 3mm thick wall care putty .

M&L for preparation of new plastered surfaces and applying three coats of white wash on ceiling complete all as specified and as directed by the Engineer-in-Charge.

S&F mild steel work in hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed by the Engineer-in-Charge.

M & L for preparation of new steel Surfaces of any description, over 10cm in width or girth,not otherwise described and applying two coats of synthetic enamel paint over a coat of redoxide primer

Taking down PVC (SWR) pipes (of any radius) including joints etc. complete all as specified and as directed by the Engineer-in-Charge.

Dismantling Structural steel work including doors, gates etc.

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings

Dismantiling posts or structs (wood, steel or R.C.C) any section embeded in concrete, brickwork, masonary, etc including taking out embedded portion and making good disturbed ground.

M&L for rendering 10mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement with WPC complete all as specified and as directed by the Engineer-in-Charge.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm,watering, and removing surplus soil to a distance n exc 50 m and making good surface

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m

M&L Cement concrete type B-2 1:2:4 (40mm graded aggregate) in foundations, filling and mass concrete

S&F Single stanchions,built up of one MS Tube conforming to IS-1161-1979 grade Yst 240 with flange plates,,caps,bases,splices angle brackets,cleats and other connections

S&F Steel work in tubular trusses and column including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 and is painted one shop coat of zinc chromate primer paint (including preparation of surface) at Contractor’s workshop before fabrication

S & F Mild Steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe 410 -W (Gde- E- 250) quality- A

M&L Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors;ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165

S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

S&F Mild steel screw bolts 5 to 10mm neck dia (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long.

M & L for 50 mm thick Plain Cement concrete of type B1, 1:2:4 (20 mm graded aggregate) in floors finished even and smooth without using extra cement with WPC .

Providing and applying acrylic cementitious , elastomeric , two component waterproof coating of master builders solutions or equivalent , by mixing both the components to a lump free consistency by suitable means and applied on the prepared surface in 2 or 3 coats at an interval of 4 to 8 hours beytween coats , depending on the atmospheric conditions , applied at a total consumption of 3 Kg/Sqm to achieve a total dry fill thickness of 1.5 mm and coating shall be continued along the wall and allowed to cure etc. Coating shall offer the following performance properties. 1.Tensile strength-1 MPa as per ASTM D 412 2.Elongation -35 % as per ASTM D 412 3.Water penetration -No leakage at 5 bars as per DIN 1048

M&L Preparation of new or previously untreated Surfaces of any description, over 10cm in width or girth,not otherwise described, priming with red oxide, zinc chrome and aplying two coats of synthetic enamel paint

M&L for preparation of old plastered surfaces and applying two coats of cement based paint on Priming plastered and other surfaces with alkali resistant priming pain orone coat of water proffing paint on surface of walls

M&L for Writing letters or figures (Block. Roman, Italic or Indian) n exc. 30 cm high

S & F for Welded steel wire fabric, 4mm dia galvanised steel wire 50x50mm mesh made up into matress or cages, lapped, wired and laid in position and fixed complete to steel members n.exc 4kg per Sqm, fixed complete to steel members.

M&L for cement concrete in roof kerbs or mud stops, rounded or chamfered on edges using type C1 1:3:6 (20mm graded aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bads, plinth courses, string couses, lacing cources, parapets and railings upto 60 cm in height, coping, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed.

S&F MS works as in wind ties using flat iron incl all necessary drilling bolting reiveting etc and similar work conforming to Fe-290 Gde E-165. complete all as specified and directed by Engr-in-Charge

Taking down carefully existing aluminium conductor point wiring (light / fan / socket or power point) complete, with all fittings such as switches, socket, regulator, ceiling rose, utility light fittings and lamp holders etc and removing materials from site and making good the disturbed surfaces of walls roof and floor etc

Taking down carefully by unscrewing from boards / outlet boxes, fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, brackets, ceiling fittings, bulk head fittings, tube light fittings and fan regulators etc. for reuse at site complete all as specified and as directed. (Note : To be measured only when found serviceable in all respects complete for reuse)

M&L for Point wiring for one light controlled by 1 one way switch with 1.5 Sqmm PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable 1100 Volts grade drawn carefully through existing/New concealed conduit along with 1.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire, connected to earth dolly and to be terminated in and including new pressed steel sunken boxes , readily available (Having wall thickness not less than 1.22 mm for boxes upto a size of 200 mmX300 mm and beyond that the wall thickness shall be not less than 1.63 mm) concealed type with 3mm thick bakelite sheet cover for mounting switches, sockets, fan regulators etc including testing on completion complete including making good disturbed surface all as specified and as directed.

All as per Item no 124 here-in-before but for one light point controlled by two 2 way switch

All as per Item no 124 here-in-before but for one fan E/Fan point controlled by 1 one way switch and regulator all as specified and as directed.

All as per Item no 124 above but for one 3 pin switch socket outlet, 5 Amp on independent board all as specified and as directed.

All as per Item no 124 here-in-before but for one switch socket outlet, 5 Amp on same board with other switches

All as per Item no 124 here-in-before but for one16 Amp 3 & 5 pin switch socket outlet, independent with 4 Sqmm single core multi-stranded copper conductor cable (FRLS) along with 2.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire

All as per Item no 124 here-in-before but for one bell point controlled by one bell push on the same board with other switches or independent

M&L for Sub main wiring with two single core PVC insulated un-sheathed cable with multi-stranded copper conductor of 6 sq mm size and drawing into and including concealed PVC conduit with earthing cable of PVC insulated un-sheathed stranded copper conductor of size 4 sqmm, single core, as earth continuity wire

M&L for Switch socket combination 2 in 1 3 pin 5 and 15 amp flush type universal all as specified

M&L for Switch piano flush button single pole one way 5 amps all as specified and as directed.

Fixing only switch flush button single pole one way 5 amp (Note : Material obtained from item No 123 here in before)

M&L for Switch flush type, single pole Two way 5 Amps 230 volts

M&L for Switch socket combination 2 in 1 3 pin 5 amp flush type universal

Fixing only Switch socket outlet 5 amp flush type (Note : Material obtained from item No 123 here in before)

M&L for Ceiling rose surface bakelite three terminals all as specified and as directed.

Fixing only Ceiling rose surface bakelite three terminals (Note : Material obtained from item No 123 here in before)

M&L for Fan regulator electronic deluxe rotary step type

Fixing only fan regulator any type all as specified and as directed. (Note : Material obtained from item No 123 here in before)

M&L for Bell ding dong AC 230 volt single pole

M&L for Bell push, flush type 6 amps

M&L for Sheet metal enclosure for MCCB, DBs, phosphatised, Powder coated , Triple Pole and Neutral (TPN), suitable for 4 way, Double door 415 Volts

M&L for Sheet metal enclosure for MCB, DBs, phosphatised, Powder coated , single pole and neutral (SPN) 240 Volt , double door, suitable for 8way with dim rail earth and neutral bar all

M&L for MCB Four Pole (FP) C curve 10kA breaking capacity of 63 amps, 415 Volts in proper position

M&L for MCB Single Pole (SP) C curve 10kA breaking capacity of 6 to 32 amps, 240 Volts in proper position

M&L for MCB Double Pole of capacity up to 40 amps, 240 Volts c-series with 10kA breaking capacity

M&L for Indoor luminare decorative batten for wall/ceiling mounting box type energy efficient saving LED BATTEN LIGHT 10 W,230 V,50 HZ, slim integrated design easy install incl twin twisted copper conductor flexible wire from ceiling rose to connector

M&L for Indoor luminare decorative batten for wall/ceiling mounting box type Extruded aluminium housing ,PC Diffuser, energy efficient saving LED BATTEN LIGHT 20W,230 V,50 HZ, slim integrated design easy install incl twin twisted copper conductor flexible wire from ceiling rose to connector all as specified and as directed. MAKE CG CAT NO. CCS-100-20-65-HL2-DP-NWH or equivalent as approved by GE

M&L for 10 W LED decorative CITY 3 wall/surface mounting polycarbonate body suitable for retrofit LED Lamp Base B-22 incl lamp ,all as specified and as directed. Make: Havells Cat Part No LHDL06160099 or equivalent as approved by GE

M&L for LED mirror light fittings 07 W,230 V,50 HZ suitable for indoor and outdoor applications complete all as specified and as directed.

M&L for LED bulk head fittings 10 W,230 V,50 HZ suitable for indoor and outdoor applications complete all as specified and as directed. Make Surya cat no SLE BH 10 W or equivalent of Phillips/Crompton.

M&L for Wall security LED light luminaire fitting 1X25 W and including cable for connection from celling rose with 1.5 Sqmm PVC insulated stranded copper conductor (FRLS) cable including 25 mm GI bracket medium grade 1m long bent to shape including bolt, nut,washer,clamp etc

Taking down carefully ceiling fan any sweep and any make after disconnecting the electrical connection, dismantling the blades and removing fan incl blades for safe custody for reuse and re-assembling the fan complete and refixing the fan in same position including all electrical connection

Taking out and removing burnt copper winding, cleaning the armature, rewinding the fan armature for 1200mm sweep fan with new super enamelled copper wire of existing gauge including supply and fixing necessary insulating materials etc and varnishing with approved grade of insulation varnish and heating up and testing

Supply only bearing No.6201/6202 for ceiling /Exhaust fan (Make - TATA/SKF/NBC ).

Supply only fan condenser upto 2.5 mfd (Make - USHA/UNIVERSAL/Havells).

M&L for Painting of ceiling fans complete of any sweep/make with one coat of first quality synthetic enamel paint of approved tint by spray including preparation of old painted surface and removing all dust, oil mark etc and filling cavities with filler materials, and writing serial / MES number as specified (with paint of black colour with each letters/figures in Block of height n.exc 2 cm ) complete

M&L for Ceiling fan complete with accessories 230v SP 1200 mm sweep and connection with ceiling rose with MS hook for hanging of suitable size old u/s kept in MES store yard all as specified and as directed. Make Havells Model No. ES 50 or Equivalent as approved by GE

M&L for Exhaust fan wall mount type 300 mm sweep metal body , single phase with louver shutter and connecting up including provision of hold fasts for fixing fan and louver shutter with cutting of hole and necessary PCC(1:3:6)

M&L for Exhaust fan wall mount type 250 mm sweep PVC body , single phase with louver shutter and connecting up including provision of hold fasts for fixing fan and louver shutter with cutting of hole and necessary PCC(1:3:6)

Taking down existing unserviceable MS box after disconnecting all electric connection and Supply and fixing factory made enclosure box for mounting meter panel of size 0.6x0.6x0.2m indoor and wall mounting type made of 2mm thick MS sheet with front side openable with two nos hinged type door with locking arrangement and danger notice board, dust and vermin proof including providing all necessary electrical connection by supply and fixing single core multi stranded copper conductor FRLS cable of appropriate size, making circular hole for cable entry and exit including cable gland of required size, incl two coat of powder coated paint to out side surface and two coat of synthetic enamel paint to inside surface over a coat of red oxide , and making good the disturbed surfaces or wall etc complete incl necessary nut,bolt, washers for mounting on wall and making provisions for mounting 04 nos electric meters and MCBs

M&L for AC single phase static Electronic KWH energy meter of accuracy class 1.0, 240v, 50 Hz , with Backlit LCD Display, of Rating 10-60 A With Transparent Hinged Type Box with six month History of Energy in KWH with taking down old meter and kept in MES store yard with accessories.

Excavation in trenches not exc 1.5 mtr wide and not exc 1.5 mtr in depth; for trench of FRLS cable etc and getting out in Soft/loose soil complete

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in Soft/loose soil complete

M&L for Sand cushioning for protection of underground FRLS cable consolidated and compacted with clean dry sand all as specified and as directed (Compacted thickness shall only be measured and paid)

M&L for XLPE insulated GI wire/strip armoured electric power cable (Heavy duty) ISI marked with stranded aluminium conductor 1100 volts grade, cross sectional area 25Sqmm 3.5 core laid in trench /poles/on wall

M&L for Common burnt clay building bricks sub-class B of size 230x113x75

Drilling of hole horizontally 80/40 mm dia bellow the road for providing casing pipe of cable protection by using mechanical/hand drill

M&L for Galvanized iron tubing 50 mm bore light grade with all fitting for protection of FRLS cable, laid in trenches/wall/floor incl necessary clamp, bolt/nut if any all as specified and as directed. Note: Excavation ,earth work shall be measured and paid separately

M&L for Earthing complete with 2.5m CI pipe 80 mm dia with flanged ends, centrifugally cast, class A, in any length, joints with suitable stainless steel nuts and bolts and sufficient slot up to 2 mtrs length buried directly and preferably vertically in ground with top flanged ended 2 mtrs below ground label welded/connected with GI strip 32X6 mm dia Galvanised iron or steel wire, connected to Earth pit to DB for earthing including filling the pit with charcoal common salt surrounding the earth pipe including drilling 400 mm dia bore in any strata of soil to lower the CI pipe complete

M/s SRINIVASA REDDY CONSTRUCTIONS

POTHINA SAMBAMURTHY

SAI SAMPATH ELECTRICAL AND ENGINEERING

SRI VENKATA SAI MANIKANTA CONSTRUCTIONS