RVI FOR WZ

SUPPLY AND FABRICATION — upply, fabrication of blue facia: The width ofthe blue facia shall be as per the requirement ofthe user clause no.1.1.6of genera instructionsfor canopy signage. The ACM to be cladded onsupportin

SUPPLY&FABRICATION,CORN — upply & fabrication of corner facia:3.9 m longsilver corner facia + 560 mm form PET G Thelength of the corner facia includes s ver faciaplus PET G material ( spine) portion asindicated in the clause no.1.1.6 of generalinstructions for canopy signage. e width /length of the corner facia and form PET G (spine) dimension will be guided by the clause no.1.1.6of general instruct ns for canopy signage. TheACM to be cladded on supporting MS framework. Thefabrication of the supporting frame, cladding ofsi er facia in ACM material and forming of PET Gmaterial shall be made as per the drawing givenin the tender. The drawing enclosed n thetender are indicative. The detailed fabricationand shop floor drawings shall be developed by thevendor and submitted to CL for approval.Approval for fixing of canopy structure should beobtained prior to execution of the job. Peel -off protective ilm of ACM to be removed at siteafter final inspection. Rate to include supply,installation, testing, commissioning of LEDlig ing along with suitable power driversincl.cabling ( Detailed data sheet & typicalarrangement is enclosed. However, the vendors ll submit the design document of LED modulearrangement based on the data sheet for eachelement& approval of the same by HPCL sit incharge). The PET G spine shall be pasted withVinyl in approved colour. Mode of measurement :The measurement for corner facia ill be innumber and measured length as given below shouldbe from the corner of the facia upto outer pointof form PET G spine ( aken vertical). Rate toalso include fabrication of MS supporting frameworks, PET -G, Vinyl Reflector, 1mm Al sheet attop, 1 mm I sheet for flashing .All work to bedone in line, level and plumb.( For 800 or 900 mmwidth of Corner facia)

SUPPLY&FABRICATION,CORN — upply & fabrication of corner facia:3.5 m longsilver corner facia + 500 mm form PET G Thelength of the corner facia includes si er faciaplus PET G material ( spine) portion asindicated in the clause no.1.1.6 of generalinstructions for canopy signage. T width /length of the corner facia and form PET G (spine) dimension will be guided by the clause no.1.1.6of general instructi s for canopy signage. TheACM to be cladded on supporting MS framework. Thefabrication of the supporting frame, cladding ofsil r facia in ACM material and forming of PET Gmaterial shall be made as per the drawing givenin the tender. The drawing enclosed thetender are indicative. The detailed fabricationand shop floor drawings shall be developed by thevendor and submitted to H L for approval.Approval for fixing of canopy structure should beobtained prior to execution of the job. Peel -off protective lm of ACM to be removed at siteafter final inspection. Rate to include supply,installation, testing, commissioning of LEDligh ng along with suitable power driversincl.cabling ( Detailed data sheet & typicalarrangement is enclosed. However, the vendorsh l submit the design document of LED modulearrangement based on the data sheet for eachelement& approval of the same by HPCL site ncharge). The PET G spine shall be pasted withVinyl in approved colour. Mode of measurement :The measurement for corner facia ll be innumber and measured length as given below shouldbe from the corner of the facia upto outer pointof form PET G spine ( ken vertical). Rate toalso include fabrication of MS supporting frameworks, PET -G, Vinyl Reflector, 1mm Al sheet attop, 1 mm sheet for flashing .All work to bedone in line, level and plumb.( For 800 or 900 mmwidth of Corner facia)

SUPPLY&FABRICATION,CORN — upply & fabrication of corner facia:3 m longsilver corner facia + 500 mm form PET G Thelength of the corner facia includes silv faciaplus PET G material ( spine) portion asindicated in the clause no.1.1.6 of generalinstructions for canopy signage. The idth /length of the corner facia and form PET G (spine) dimension will be guided by the clause no.1.1.6of general instruction for canopy signage. TheACM to be cladded on supporting MS framework. Thefabrication of the supporting frame, cladding ofsilve facia in ACM material and forming of PET Gmaterial shall be made as per the drawing givenin the tender. The drawing enclosed in hetender are indicative. The detailed fabricationand shop floor drawings shall be developed by thevendor and submitted to HPC for approval.Approval for fixing of canopy structure should beobtained prior to execution of the job. Peel -off protective fi of ACM to be removed at siteafter final inspection. Rate to include supply,installation, testing, commissioning of LEDlighti along with suitable power driversincl.cabling ( Detailed data sheet & typicalarrangement is enclosed. However, the vendorshal submit the design document of LED modulearrangement based on the data sheet for eachelement& approval of the same by HPCL site i charge). The PET G spine shall be pasted withVinyl in approved colour. Mode of measurement :The measurement for corner facia wi be innumber and measured length as given below shouldbe from the corner of the facia upto outer pointof form PET G spine ( ta n vertical). Rate toalso include fabrication of MS supporting frameworks, PET -G, Vinyl Reflector, 1mm Al sheet attop, 1 mm GI heet for flashing .All work to bedone in line, level and plumb.( For 800 or 900 mmwidth of Corner facia)

SUPPLY&FABRICATION,CORN — upply & fabrication of corner facia:2.5 m longsilver corner facia + 500 mm form PET G Thelength of the corner facia includes si er faciaplus PET G material ( spine) portion asindicated in the clause no.1.1.6 of generalinstructions for canopy signage. T width /length of the corner facia and form PET G (spine) dimension will be guided by the clause no.1.1.6of general instructi s for canopy signage. TheACM to be cladded on supporting MS framework. Thefabrication of the supporting frame, cladding ofsil r facia in ACM material and forming of PET Gmaterial shall be made as per the drawing givenin the tender. The drawing enclosed thetender are indicative. The detailed fabricationand shop floor drawings shall be developed by thevendor and submitted to H L for approval.Approval for fixing of canopy structure should beobtained prior to execution of the job. Peel -off protective lm of ACM to be removed at siteafter final inspection. Rate to include supply,installation, testing, commissioning of LEDligh ng along with suitable power driversincl.cabling ( Detailed data sheet & typicalarrangement is enclosed. However, the vendorsh l submit the design document of LED modulearrangement based on the data sheet for eachelement& approval of the same by HPCL site ncharge). The PET G spine shall be pasted withVinyl in approved colour. Mode of measurement :The measurement for corner facia ll be innumber and measured length as given below shouldbe from the corner of the facia upto outer pointof form PET G spine ( ken vertical). Rate toalso include fabrication of MS supporting frameworks, PET -G, Vinyl Reflector, 1mm Al sheet attop, 1 mm sheet for flashing .All work to bedone in line, level and plumb.( For 800 or 900 mmwidth of Corner facia)

SUPPLY&FABRICATION,HP — UPPLY & FABRICATION OF HP LOGO (SIZE 1.0 M) THESIZE OF THE LOGO SHALL BE AS PER THE REQUIREMENTOF CANOPY SIGNAGE. THE FABRICATIO OF THESUPPORTING FRAME, CLADDING OF SILVER FACIA IN ACMMATERIAL AND FORMING OF PET G MATERIAL SHALL BEMADE AS PER THE DRAWING VEN IN THE TENDER. THEDRAWING ENCLOSED IN THE TENDER ARE INDICATIVE.THE DETAILED FABRICATION AND SHOP FLOOR DRAWINGSSHALL BE D ELOPED BY THE VENDOR AND SUBMITTED TOHPCL FOR APPROVAL. APPROVAL FOR FIXING OF CANOPYSTRUCTURE SHOULD BE OBTAINED PRIOR TO EXECU ONOF THE JOB. PEEL - OFF PROTECTIVE FILM OF ACM TOBE REMOVED AT SITE AFTER FINAL INSPECTION. RATETO INCLUDE SUPPLY, INSTALLATI , TESTING,COMMISSIONING OF LED LIGHTING ALONG WITH SUITABLEPOWER DRIVERS INCL.CABLING ( DETAILED DATA SHEET& TYPICAL ARRANGEME IS ENCLOSED. HOWEVER, THEVENDOR SHALL SUBMIT THE DESIGN DOCUMENT OF LEDMODULE ARRANGEMENT BASED ON THE DATA SHEET FOREACH ELE NT& APPROVAL OF THE SAME BY HPCL SITEIN CHARGE) MS SUPPORT FRAME, PET G , VINYL . ALLWORK TO BE DONE IN THE LINE , LEVEL & PLUMB MODEOF MEASUREMENT : THE MEASUREMENT FOR HP LOGO WILLBE IN NUMBER AS PER THE DRAWING."

SUPPLY&FABRICATION,HP — upply & fabrication of HP logo (size 1.16 m) :The size of the logo shall be as per therequirement of canopy signage. The fabric ionof the supporting frame, cladding of silver faciain ACM material and forming of PET G materialshall be made as per the draw g given in thetender. The drawing enclosed in the tender areindicative. The detailed fabrication and shopfloor drawings shal be developed by the vendorand submitted to HPCL for approval. Approval forfixing of canopy structure should be obtainedprior execution of the job. Peel - offprotective film of ACM to be removed at siteafter final inspection. Rate to include supply, stallation, testing, commissioning of LEDlighting along with suitable power driversincl.cabling ( Detailed data sheet & typical rrangement is enclosed. However, the vendorshall submit the design document of LED modulearrangement based on the data sheet for achelement& approval of the same by HPCL site incharge) MS support frame, PET G , Vinyl . Allwork to be done in the line , le l & plumb. Modeof measurement : The measurement for HP logo willbe in number as per the drawing.

SUPPLY&FABRICATION,WHITE MHLP-CVR PURCHASE PLANT — upply & fabrication of white facia : The widthof the white facia shall be as per the drawing.The ACM to be cladded on supporting S framework. The fabrication of the supporting frame,cladding of white facia in ACM material shall bemade as per the drawing g en in the tender. Thedrawing enclosed in the tender are indicative.The detailed fabrication and shop floor drawingsshall be d eloped by the vendor and submitted toHPCL for approval. Approval for fixing of canopystructure should be obtained prior to exec ionof the job. Peel - off protective film of ACM tobe removed at site after final inspection. Allwork to be done in line, l el and plumb. Mode ofmeasurement : The measurement for white faciawill be in running metre of the facia measuredbetween top ed of the installed facia . Ratefor supporting frame ,flashing at the rear sideand bottom side shall be included in the rate.Sup y & fabrication of white facia

SUPPLY&FABRICATION,FACIA, MHLP-CVR PURCHASE PLANT — upply & fabrication of facia for salesbuilding : The width of the facia for thebuilding shall be as per the drawing. The ACM o be cladded on supporting MS framework. Thefabrication of the supporting frame, cladding ofbuilding facia in ACM material shall e made asper the drawing given in the tender. The drawingenclosed in the tender are indicative. Thedetailed fabrication and op floor drawingsshall be developed by the vendor and submitted toHPCL for approval. Approval for fixing of canopystructure s uld be obtained prior to executionof the job. Lettering for facilities to beprovided in Acrylic ( pasted with vinyl ) onbuild g facia as per approval by HPCL i.e. SalesBuilding , ATM, Lube Express , Club Bites etc.Peel - off protective film of ACM to be movedat site after final inspection. All work to bedone in line, level and plumb. Mode ofmeasurement : The measurement for b lding faciawill be in running metre of the facia measuredbetween top edge of the installed facia frontface. Rate for supportin frame, flashing at therear side shall be included in the rate.

SUPPLY AND FABRICATION — UPPLY & FABRICATION OF ALUMINUM COMPOSITE PANEL( IN ANY APPROVED COLOR ) CLADDING TO COVERADDITIONAL AREA AT OUTLET INCLUDING SU ORTFRAMING OF REQUIRED SIZE. MODE OF MEASUREMENT:THE MEASUREMENT SHALL BE IN AREA ( L X B , SQM )OF ACM SHEET INSTALLED AT SIT NO WASTAGE SHALLBE PAID EXTRA."