SPL REPAIR TO BLDG NO P-15A, P-15BCD AND P-17 AT ARMY AREA UNDER GE (ARMY) NO 2 JODHPUR

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises, complete all as specified and directed.

Demolition of cement concrete incl terrazo flooring (un-reinforced) in ground floor and paving not exceeding 15cm thick (below or above ground level) built in cement mortar, complete all as specified and directed.

Dismantling stone slabs and tiles of any description or thickness laid , bedded and pointed in any mortar as in floors, aprons etc. complete all as specified and directed.

Dismantling of stone slabs as in suspented slab in roof chajja, landing slab Etc of any description or thickness laid , bedded and pointed in any mortar etc. complete all as specified and directed.

Dismantling of ceiling boards of any thickness including cover fillets etc, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling Asbestos Cement Corrugated or Semicorrugate in Roof covering and cladding complete all as specified and directed.

Dismantling of Framed timber scantling 40sq cm and over in section in any position complete all as specified and directed.

Dismantling of Framed timber fillet, rails, post, rafters, purlin etc n. exc 40sq cm in section in any position complete all as specified and directed.

M&L 75 mm thick cement concrete type D2, 1:4:8 (using 40 mm graded stone agg) in sub base of flooring/ hard standing complete all as specified and directed.

M&L 25 mm thick PCC 1:2:4 type B1 using 20mm graded stone aggregate bedding to tiles/Kota stone as in levelling course all as specified and ditedted at site complete all as specified and directed. Note : the same will be provide where require as directed by EIC

M&L for factory made machine pressed precast concrete interlocking paver block of any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with coloured pigment made of PVC moulded (or rubber mould) with vibrating system, with and including 50mm thick sand cushioning, including PCC in edges of pavers, complete all as specified and directed. Note : The cost of sand cushion and PCC to edges is not included in quoted rate.)

M&L for sand Stone slab (jodhpur stone) 40 mm thick dressed true and square as in flooring etc . punched dressed on exposed faces/edges rounded or chamfered and self faced set ,jointed and pointed as in plinth protection and bedded on 15mm screed bed in cement mortar 1:4 , complete all as spd as directed

M&L for Stone slab ( Jodhpur stone) 50 mm thick dressed true and square, in one length not less than 60cm and n. exc 200cm in landing , slab, shelf , chajja etc., punched dressed on exposed faces/edges rounded or chamfered and self faced other side embedded or bedded on cement mortar 1:4 , set ,jointed and pointed complete all as spd as directed

M & L for machine cut kota stone slab flooring 18-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

M & L for machine cut kota stone slab 15-18mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including 10 mm thick backing coat in CM 1:4 complete all as specified and directed. Note: Kota stone in Step will be placed in single piece with groove lines at edge.

M&L for non skid ceramic colored tiles , 7 to 8 mm thick (square / rectangular) area of each tile exc 0.11 sqm but n.exc 0.18 sqm as in flooring etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed/ bedding layer in CM (1:6) complete all as specified and as directed.

M&L for ceramic colour tiles in vertical surface of size 350 X 250 x 7/450x300x7 mm thick, jointless type, set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with and including 10 mm thick rendering in CM (1:4) for receiving the tiles, complete all as specified and as directed.

M&L for granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall), window sill, door sill, window jamb etc , 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.complete all specified and directed.

Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) and semi/fully perforted false ceiling tiles of Size 595 x 595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS-8225:1987, Noncombustible as per BS 476 (part 4 )-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15 x 32 mm of length 3000mm,cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module of size 600x600mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000 mm length and Lshape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall I partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge.

S&F of pre-painted 0.50mm thick Gavalume Aluminium Zinc coating GI based corrugated / semi corrugated / trapezoidal steel sheet of any colour having tensile strength 550 MPa and AZ 150 grade as in roof covering/cladding to walls, fixed with self tapping screws, complete all as specified and directed.

S&F pre-painted Galvalume Aluminium Zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength 550 MPa and AZ 150 grade as in ridge of roof covering and cladding fixed with self tapping screws, complete all as specified and directed.

M&L for structural steel Fe-410-W(Gde-E-250) quality B for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, complete all as specified and directed.

S & F framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

Supply and fixing stainless steel (grade 304) railing made of hollow tubes , channel, plates, etc. including welding , grinding, buffing, polishing, and making curvature (where required) and fitting the same with necessary stainless steel nuts and bolts complete including fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc. of required size on the top of the floor/staircase or side of the waist slab with suitable arrangements as per direction of the Engineer-in-Charge. Notes: For payment purpose only weight of the stainless steel members shall be considered excluding fixing accessories such as nut, bots fasteners etc as these are deemed to be included in quoted rate

M&L for preparation of new steel or iron surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over and including a coat of red oxide primer complete all as specified and directed

M&L for ATT ,providing and injecting chemical emulsion for Post Constructional along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete all as spd

M&L for ATT , providing and injecting of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as spd

Demolition of RCC Not exc 15cm thickness Roofs, floors (other than ground floors), beams staircases, landing, chajjas, Cover slab and similar suspended work.

M&L for RCC 1:2:4 type B-1 (Nominal Mix) (using 20 mm stone agg) as in Chajja supported on walls, beams and columns in roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as spd

M&L for mild steel deformed TMT bars 10mm dia and over (as in reinforcement) cut to length, bent to shape require including cranking, bending spirally for hooking for column, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as spd and directed by engr in charge

M & L for rough finish formwork to soffits of suspended slabs such as roof slabs, floor slabs and lintels, landingand similar work n exc 200mm thick. complete all as spd and directed by engr in charge

Demolition of brick/Stone work built in cement mortar or lime mortar including all quoins arches, pillars etc complete all as specified and directed.

M&L for squared rubble stone wallingJodhpur type,regular coursed,well bonded, bedded and solidly hearted,built in CM(1:6) complete all as specified and directed.

Extra over stone masonry for hammer dressing to facestones with maximum depression on face from a straight edge held against the dressed surfaces not exc 20mm and dressing face beds and joints as specified to squared rubble walling, Jodhpur type, brought upto course complete all as specified and directed.

M&L for brick work with old size fly ash bricks, straight or curved on plan exc. 6 M mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for half brick thick wall with old size fly ash bricks, straight or curved on plan to any radius built in cement mortar 1:4, complete all as specified and directed.

Taking out cement plaster on brick or stone wall etc including racking out joint, hacking joints for key scrubbing down with water etc

M&L for 15 mm rendering thick in CM (1:6) on fair faces of brick work/stone surfaces finished even & fair (without using extra cement) complete all as specified and directed.

M&L for rendering 15mm thick in two coats (1st coat 10 mm thick in CM 1:6 & 2nd coat 5 mm thick in CM 1:4 with WPC) on fair faces of brick/stone surfaces, finished even & smooth (without using extra cement) complete all as specified and directed. Note: WPC in 5 mm thick 2nd layer plaster measured and paid separately.

M&L for 15mm rendering thick in CM (1:4) on fair faces of brick work/concrete surfaces finished even & smooth (without using extra cement), complete all as specified and directed.

M&L for 10 mm rendering thick in CM (1:3) on fair faces of concrete surfaces in ceiling finished even & smooth (without using extra cement) including taking down cement plaster on brick or stone wall,dado and skirting etccomplete all as specified and directed.

M&L for preparation of new plastered of wall surface and applying two coats of oil bound distemper, over a coat of chalk whitening primer over and incl a layer 3mm thick of wall care putty to get even and smooth level finish on new plastered surface of internal wall, complete all as specified and as directed.

M&L for preparation of surfaces of walls and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint (weather proof) of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces. complete all as specified and directed. Note : The contractor shall produce batch certificate & delivery challans directly from paint manufacturer to establish the authenticity of the material. The batch testing certificate shall be brought at the site along with paint manufacturer's drums with seal intact.

M&L for preparation of new plastered of ceiling surface and applying three coats of white wash on new plastered surface of ceiling surface, complete all as specified and as directed.

M&L for complete removal of existing treatment and preparation of surfaces of walls by scrapping/sand paper rubbing and finally washing with watering and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint (weather proof) of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces. complete all as specified and directed. Note : The contractor shall produce batch certificate & delivery challans directly from paint manufacturer to establish the authenticity of the material. The batch testing certificate shall be brought at the site along with paint manufacturer's drums with seal intact.

M&L for complete removal of existing treatment by brushing, washing, rubbing down, scraping from old treated surfaces of wall and applying two coat of oil bound distemper over a coat of chalk whitening primer, over a layer of (JK/Birla) 3.0 mm thick wall care putty to get smooth and level finish, complete all as specified and directed.

M&L for complete removal of existing treatment by brushing, washing, rubbing down, scraping from old treated ceiling surfaces includes preparation and applying Three coats of White wash , complete all as specified and as directed.

M&L for complete removal of existing treatment by brushing, washing, rubbing down, scraping from old treated wall surfaces includes preparation and applying Two coats of snowcem or cement base paint complete all as specified and as directed.

M&L of water proofing treatment to non-accessible roof slab with APP based modified polymeric membrane centre core 100mm micron HMHDPE outer film 20 micron each having thickness 3mm weight not less than 3kg/Sqm as per manufacturer’s instructions laid with torch application complete all as specified and directed by Engineer-in-Charge with following course of description below:- (a) 10 mm thick plaster in CM 1:4 with WPC (liquid water proofing compound @ 0.20 Ltr/bags(50 Kg Bag)) will be applied over the roof slab (subjected to condition as mentioned in notes) . After the plaster is cured the roof will be tested for water tightness by ponding with water for seven days for any seepage is observed the rectification will be carried out by pressure grouting under the pressure of 5kg/sqcm using cement based grout. After the surface is repaired the slab will be tested for water tightness again before proceeding with further treatment. (b) the surface of roof, parapet and gutters, drain mouths, etc. over which waterproofing treatment is to be applied shall be cleaned of all foreign matter such as, fungus, moss, dust etc by wire brushing and dusting. For cast iron drain outlets a groove shall be cut around to tuck in the treatment. Concrete angle-fillets shall be provided at junctions between roofs and vertical faces of walls (parapet and other walls) around obstacles such as pipes, chimney stacks, etc. and other similar situation to ease up about corners. (c) Bitumious based primer confiorming to IS: 3384 @ 0.3 kg/Sqm to be applied on prepared surface, till the surface is propely impregnated. (d) After the application of approved bituminous primer the water proofing membrane shall be laid on the primed surface by torch application method as per manufacturer's instruction. The overlap while toching shall be 100mm in longitudinal direction and 100 mm in transverse direction. All overlap joints shall be sealed thoroughly by thermo fusing both the membrane layer and seling it with the help of hot trowel. The overlap joints shall be made as a monolithic layer. (e) All joints and changes in direction should be curved with cement mortar 1:3 mixed with SBR latex @ 200ml per bag of cement and cured well before laying the membrane. (f) after apllication of APP membrane one coat of aluminium paint @ 0.20 Kg/Sqm over APP membrance will be applied Note : The cost of all items i.e. from Sr No. (a) to Sr No.(f) are included in quoted rate and no separate payment will be done for the above except liquid WPC.

Supply only liquid water proofing compound, mixed in CM as per manufacturer instruction, complete all as specified and directed. Make : Dr Fixit LW+

M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in padding etc and roof kerbs,tank staging etc complete all as specified and directed.

Taking down chowkhats with shutters (without taking off shutters from the frame) area exc 1.5 sqm but not exceeding 4 sqm each complete all as specified and as directed.

All as per item No. 53 here-in-above but not exc 1.5 sqm each complete all as specified and as directed.

M&L for Factory made single extruded WPC (Wood Polymer Composite) solid door Chowkhat of size 45 x 70 mm for cuboard, comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp￾ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant 152 SECTION 8 and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as spd

M&L for Factory made single extruded WPC (Wood Polymer Composite) solid door Chowkhat of size 65 x 100 mm for single shutter comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp￾ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant 152 SECTION 8 and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as spd

M&L for Factory made single extruded WPC (Wood Polymer Composite) solid door Chowkhat of size 65 x 125 mm for double shutter comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp￾ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant 152 SECTION 8 and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made

S&F for factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately)

M&L 30mm thick factory made solid WPC (Wood plastic composit) moulded gauged door shutter with wire mesh in any number of division with brown wood grain texture, including stainless steel wire shall mesh be fixed with 15x15 Square tube in side rails with screwing 8x28 heat metal zink coated screws can be remove or fie again of the shall be as per manufacture instruction complete all as specified and complete all as specified and complete all as specified and directed.

S&F powder coated ( minimum thickness of powder coating not less than 50 micron) aluminium window shutter (three shutter) sliding type with frame of powder coated aluminium channel section suitable for sliding aluminium shutters weighing 0.55Kg/M of three channel including necessary joining cleats glazing clips rubber packing Powder coated aluminium shop beading screws with two shutter Including 5mm thick coloured glass and one shutter with wiremesh of 0.56 mm in nominal dia of wire average width of aperture 1.18 mm, including necessary locking arrangement and handle etc; as specified etc complete all as specified and directed.

S&F powder coated ( minimum thickness of powder coating not less than 50 micron) aluminium ventilator shutter openable type with frame of powder coated or aluminium channel section suitable for top hung aluminium shutters weighing 0.55Kg/M including necessary joining cleats glazing clips rubber packing Powder coated aluminium shop beading screws with two shutter Including 5mm thick coloured glass and one shutter with wiremesh of 0.56 mm in nominal dia of wire average width of aperture 1.18 mm, including necessary locking arrangement and handle etc; as specified etc complete all as specified and directed. Note:- item for glass and wire mesh shall be measured seperatly

M & L 25 mm thick factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations, kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, including designer edge binding tape of required width, including dismantling of old cupboard boarding of any description all as per direction of Engineer-In- Charge. (Note: stainless steel piano hinges/soft close clip on concealed hinges shall be paid separately)

M & L 18 mm thick factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations, kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, including designer edge binding tape of required width, including dismantling of old cupboard boarding of any description all as per direction of Engineer-In- Charge. (Note: stainless steel piano hinges/soft close clip on concealed hinges shall be paid separately)

M&L for 2mm thick of 25/18mm wide PVC edge binding tape of approved quality for item No 52 & 53 including necessary sythetic resin hot pressed to edge on binding machine etc complete as per direction of Engr in charge

S&F of glass, tinted type, coloured 5.mm thick, each panes not exc 0.5 sqm, suitable for aluminium window / Ventilators / door opening and similar work, complete all as specified.

M&L for mild steel framed work section as in door or gates of angle or other section with gusset plates,rails braces etc /windows chowkhats/Shutter frame of steel gate of grade Fe-290 (Gde E-165) including all necessary machine wks i.e. cutting, welding, grinding etc, complete all as specified and directed.

M&L for 1.25mm thick Mild steel Plain black sheet as in steel gate and similar work cut to shape size hole punched including round headed screws cloutls or revetts and fixed to steel frame complete all as spd

M&L for mild steel framed work section as in holdfast or wall ties & hooks and similar small articles etc, confirming to Fe-290 Gde E 165 complete all as specified and directed.

M&L for cement concrete 1:2:4 type B-0 (12.5mm graded aggregate) for bed block for fixing of chowkhats, cills ,pre-cast lintel n.exc 1.5mtr,coping,benching etc complete all as specified.

S&F continuous (piano) hinges, mild steel bright finish in electro galvanized width of flat (when open) in 40 mm, complete all as specified and directed

S & F brass drawer/shutter handles fancy type , projection drop (50mm to 65mm) on screwed platey complete all as specified and directed

S&F of 100mm SS butt hinges ISI marked and fixed with screws or welded to angle frame, complete all as specified and directed.

S&F 300 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F of 200mm long barrel tower bolt aluminum anodized extruded section fixed with cadmium plated screws complete all as specified and directed.

S&F of 150mm aluminum handle cast D type anodized complete all specified and directed. (Make : Ashish, Classic)

S&F of mild steel ordinary rat tail rod pattern springs of size 300mm including roller and roller plate complete all as specified and directed

S&F for Door stopper 140 mm of aluminium alloy body anodised with tongue of rubber bush at one end fixed to door complete all as spd and directed by Engr in charge

S&F Rubber bush of 25mm long fixed to door complete all as spd and directed by Engr in charge

S&F 125 mm Hasp and staple, SS including bolt to hinge plate and fixed with screws complete.

S & F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm fixed with tinned tacks or galvanized wire staples complete all as specified and directed

S&F of ringfit PVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end as self socketed with an integral groove to hold the rubber gasket, with and incl rubber tighten gaskets, ringfit sockets etc, complete pipe duly fixed to wall, including taking down of eaves gutter and rain / waste water pipes including all fittings any size and pattern complete all as specified and directed.

S&F of PVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end socketed, duly fixed with cement solvent etc, complete pipe duly laid in trenches or in floors, including taking down of eaves gutter and rain / waste water pipes including all fittings any size and pattern complete all as specified and directed.

S&F of Ringfit PVC (SWR) pipe of 75 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end as self socketed with an integral groove to hold the rubber gasket, with and incl rubber tighten gaskets, ringfit sockets etc, complete pipe duly fixed to wall, including taking down of eaves gutter and rain / waste water pipes including all fittings any size and pattern complete all as specified and directed.

S&F of PVC (SWR) pipe of 75 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end socketed, duly fixed with cement solvent etc, complete pipe duly laid in trenches or in floors, including taking down of eaves gutter and rain / waste water pipes including all fittings any size and pattern complete all as specified and directed.

S&F 110 mm bore PVC (SWR) bends of any radius, complete all as specified and directed.

S&F 75 mm bore PVC (SWR) bends of any radius, complete all as specified and directed.

S&F 110 mm bore PVC (SWR) junction single (Single `T') equal or unequal, complete all as specified and directed.

S&F 75 mm bore PVC (SWR) junction single (Single `T') equal or unequal, complete all as specified and directed.

S&F PVC (SWR) vent cowl 110 mm bore, jointing to waste pipe, complete all as specified and directed.

S&F PVC (SWR) vent cowl 75mm bore, jointing to waste pipe, complete all as specified and directed.

S&F in repair 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement, complete all as specified and directed.

S&F of rotational moulded polyethylene cylindrical vertical with closed top water storage tank triple layered white colour 1000 Ltr capacity with connecting nipple, hoisted and fixed in position on new or existing foundation and making GI tubing inlet or outlet connection, with and incl disconnecting and dismantling the existing un-serviceable PVC/RCC water tank on top of roof/slab of bldgs, complete all as specified and directed.

S&F in replacement of 20 mm dia of Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iorn pipe and fixed. (minium weight 20 mm-210 gms) etc, complete all as specified and directed.

S & F in repairs 20 mm bore Gun-metal, ISI, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Taking up or down 15 mm bore steel tubing and connections, including cleaning for Refixing or removal to store.

Taking up or down 20 mm bore steel tubing and connections, including cleaning for Refixing or removal to store.

S & F 15 mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors.

S & F 20 mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors.

M&L for cutting chases,pinning in brick walls for concealed water tubing n.exc 10cm girth and making good facing where required and pointing in CM 1:3 complete all as spd

S&F in repair Vitreous China wash basin, white, flat back, size 550x400mm excluding taps, waste chain and plug and porcelain stopper but including brackets, CP waste copling, 32 mm PVC Waste pipe 600mm long complete all as specified and directed Make: Make: Kohler (Ist quality), Cera (Ist Quality), Parry ware (super fine),

Supply & Fixing in repairs Vitreous China Squatting pan, 'Orissa' pattern, size 580 x 440 mm white with integral foot rests Make: Kohler (Ist quality), Cera (Ist Quality), Parry ware (super fine).

Supply & Fix in repairs Vitreous China wash down water closet pan ( EWC), white or off white coloured including matching coloured seat covered fixed, complete all as approved by Engr-in-charge and directed.. Make: Kohler (Ist quality), Cera (Ist Quality), Parry ware (super fine),

Supply and Fix in repairs 10 Litres, PVC, valve less, syphonic action type, Flushing Cistern, low level, white inlet, ball valve, float, chain and pull, and brackets including PTMT PVC connection 600mm long and PVC 32 mm dia flush pipe. Make: Kohler (Ist quality), Cera (Ist Quality), Parry ware (super fine),

S & F in repairs 15 mm bore Bib taps, fancy type cast copper alloy,chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule. Make: Jaquar, Kohler, Cera (Ist Quality),Parry ware (super fine),Hindware(Ist Quality).

S & F in repairs 15 mm bore Bib taps long body fancy type cast copper alloy,chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule. Make: Jaquar, Kohler, Cera (Ist Quality),Parry ware (super fine), Hindware Ist Quality).

S & F in repairs 15 mm bore stop/angle cock fancy type,chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule Make: Jaquar, Kohler, Cera (Ist Quality),Parry ware (super fine),Hindware(Ist Quality).

S & F in repairs 15 mm bore conceald stop cock fancy type,chromium plated with long shank and cup screwed down, screwed for iron pipe or for brass ferrule. Make: Jaquar, Kohler, Cera (Ist Quality),Parry ware (super fine),Hindware(Ist Quality).

S&F in replacement of pillar taps, 15 mm dia, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, complete all specified and directed. Make: Jaquar, Kohler, Cera (Ist Quality),Parry ware (super fine),Hindware(Ist Quality).

S&F in replacement of PVC connection 450 x 15mm dia PTMT (PVC), complete all as directed.

S&F in repair of PVC waste pipe 32 mm dia 750 mm long for wash hand basin or for kitchen sink, complete all as specified and directed.

S & F in repair Chromium plated shower rose 200 mm size with or without swivel joints, any size, including fixing to steel pipe or union Make: Jaquar, Kohler, Cera (Ist Quality),Parry ware (super fine),Hindware(Ist Quality).

S&F in repair SS Towel Rail 600mm Long fixed with and including chromium plated brass screws

S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as directed.

S&F in replacement of premium quality corner glass shelf 300 mm with Chromium plated bracket guard and railing and fixing accessories, complete all as directed.

M&L in repair for Aluminium anodised curtain rod 25mm dia with fancy caps/lobs and wall mounting bracket cutting in to length required at site complete all as specified and directed by Eng-In-Charge Note: Bracket and end caps/lobs are included in quoted rate.

S&F in replacement of 1st quality PVC multipurpose cabinet mirror having inbuilt shelf to accommodate daily routine items with front openable door of overall size 350 x 450 mm, complete all as specified and directed.

S&F SS grating of round shape dome type 4" to 5", floor trap traps etc, complete all as specified and directed.

S&F for precast PCC 1:2:4 type BO using 12,5mm graded aggregate made of decorative cement concrete louvres and jallies 40mm thick including all moulding and frame of size 75mm x 75mm set in CM 1:4 complete all as specified and directed. Note:- Moulded frame and any type /design of jally paid under this item)

Taking down carefully aluminum/copper point wiring (light/fan/ socket/ power) complete including fittings such as switch, socket, ceiling roses light fittings etc and and making good disturbed surface of wall all as specified and directed by Engineer-in-Charge.

Material and labour for point wiring complete with 1.5 sq mm single core multi stranded copper conductor PVC FRLSH insulated unsheathed 1100 Volt grade cable in and incl PVC FRLSH CONCEALED CONDUIT PIPE (ISI Marked) with all accessories including new pressed steel terminal boxes (sunk in wall ) with 3.00 mm thick plastic laminated sheet top cover or PVC FRLSH board including PVC FRLSH top cover with 1.50 sq mm insulated unsheathed PVC FRLSH multistranded covered copper conductor for common earth and connecting to earth dolly and making good disturbed surface of wall incl matching the colour of wall/ceiling with extisting wall/ceiling colour all as specified and directed for One light/exhaust/ceiling fan point controlled by one switch one way

All as per item No 122 above but for One socket out let 5 Amps 3 Pin on same board with other switch

All as per item No 122 above but for One socket out let 5 Amps 3 pin on independent board

All as per item No 122 here in before but with single core multistranded cable of size 4 Sqmm for one 15 Amps socket outlet on independent board and multistanded insulated copper earth continuity conductor of size 4 Sq mm all as specified and directed

Supply and fixing in replacement Piano type switch 5 Amps one way.

Supply and fixing in replacement socket out let 2 in 1 multi 3 pin 5 Amps flush type universal.

Supply and fixing in replacement switch piano 15 Amps one way 240 volts

Supply and fixing in replacement socket outlet in repair 2 in 1, 3 pin, 5 and 15 Amps socket outlet 240 volts Single pole

Supply and fixing in replacement Fan step regulator flush type, min 400 watt, 240 volt, 1 module

Supply and fixing in replacement Ceiling rose on PVC FRLS board size 65 X 50 mm three terminal Complete.

Supply and fixing in replacement Lamp Holder, PVC FRLSH/polycarbonate type with back plate suitable for batten fittings.

Supply and fixing in replacement LED clear white Lamp/Bulb of 9 watt, 240 Volt type with back plate suitable for batten fittings.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete

Supply and fixing in replacement LED lights fitting 1x 20W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete

Supply and fixing in replacement LED Security light fitting 35 Watt 230 V AC outdoor type IP 65/66 with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 67 protection complete

Supply and Fix BEE 5 Star rating (BLDC) Brushless direct current motor Ceiling Fan 1200 mm sweep , complete with down rod and 3 core 1.5 sq. mm copper conductor cable from ceiling rose to fan complete with all accessories an suitable size for down Rod 230V, Make-Bajaj Model No ENERGOS 28 1200 MM GLOSSY WHITE CF without remote and equivalent in Havells,Usha,Khetan and Taking out old exist ceiling fan and deposit in MES store.

Taking down and refixing the Ceiling fan after repair work (i.e celaning, oiling, greasing, blade leveling etc) complete with down rod and 3 core 1.5 sg mm copper conductor cable from ceiling rose to fan complete with all accessories all as directed by Engr-in-Charge.

Taking down old sub main wiring and M&L for concealed sub main wiring with 2 run of 6 Sqmm FRLSH, PVC insulated, unsheathed and stranded copper conductor cable with and incl 6 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable as earth wire connected with thimble from main DB to sub main DB, drawn in to separate concealed concealed medium grade, ISI marked, non metallic PVC conduit 20 mm dia size incl all conduit accessories & fittings / junction boxes / inspection covers etc, with and incl cutting chasing and making good of disturbed surface of wall / floor/ ceiling etc as original by brick work, plastering, white washing, OBD etc as required, complete all as directed. Note : Two run of 6 Sq.mm. and one run of 6 Sq.mm (earth wire) cable incuding one run of conduit pipe will be measured as one length including making good the disturbed surfaces.

Taking down old sub main wiring and M&L for concealed sub main wiring with 2 run of 4 Sqmm FRLSH, PVC insulated, unsheathed and stranded copper conductor cable with and incl 4 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable as earth wire connected with thimble from main DB to sub main DB, drawn in to separate concealed concealed medium grade, ISI marked, non metallic PVC conduit 20 mm dia size incl all conduit accessories & fittings / junction boxes / inspection covers etc, with and incl cutting chasing and making good of disturbed surface of wall / floor/ ceiling etc as original by brick work, plastering, white washing, OBD etc as required, complete all as directed. Note : Two run of 6 Sq.mm. and one run of 6 Sq.mm (earth wire) cable incuding one run of conduit pipe will be measured as one length including making good the disturbed surfaces.

S&F in replacement TPN DB, double Door, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, TPN 4 way (Concealed flush to wall), 415 volts with bus bar rating 250 Amps, dust and vermin proof, suitable for incorporation of MCB’s and isolators etc and making all necessary connections, duly flush of wall surface, complete all as specified and directed. Note : 1. Blank plates will be included on the quoted rates. 2. All wires to be properly connected with copper lugs. 3. MCB will be measured and paid separately.

S&F in replacement sheet metal enclouser for DB'S in wall / Nitch when MCB's to be used Single pole and neutral, 8 way, Double door 240 Volt with 100 Amps rated Bus bar complete all as specified and directed.

S&F in replacement sheet metal enclouser for DB'S in wall / Nitch when MCB's to be used Single pole and neutral, 4 way, Double door 240 Volt with 100 Amps rated Bus bar complete all as specified and directed.

S&F in replacement 415 V 10KA 'C' curve miniature circuit breaker (MCB) four pole (TPN) of 40 to 100 Amp current carrying capacity in the TPN DB complete with connection testing and commissioning all as directed by Engr-in-charge

S&F in replacement 240V 10KA 'C' curve miniature circuit breaker (MCB) Double pole (SPN) of 32 Amp current carrying capacity in the DB complete with connection testing and commissioning all as directed by Engr-in-charge

S&F in replacement 240V 10KA 'B' curve miniature circuit breaker (MCB) Single pole (SP) of 40 Amp current carrying capacity in the DB complete with connection testing and commissioning all as directed by Engr-in-charge

S&F in replacement 240V 10KA 'C' curve miniature circuit breaker (MCB) Single pole (SP) of 5 Amp to 32 Amp current carrying capacity in the DB complete with connection testing and commissioning all as directed by Engr-in-charge Make :- Make : Legrand or Equivalent

M& L for Earthing complete with galvanised steel earth plate electrode 60X60cmX6.0 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5metres below normal ground level, connected to galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrial plate No. 5 connected or indicated including testing on completion.Incl necessary excavation,earth work,pcc pit,RCC cover ,funnel with watering pipe 20mm bore light grade,GI protection pipe 15 mm bore light grade.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sq mm 3.5 core

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 2 core

Excavation in trenches not exc 1.5 mtr wide and not exc 1.5 mtr deep in soft /loose soil getting out and leveling of bottom surface to required level complete all as specified and as directed by the Engr-in-charge

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm. complete all as specified and as directed by the Engr-in-charge

Removing surplus excavated rock to a distance not exc 50 m and depositing where directed at a level n.exc. 1.5 m above the starting point complete all as specified and directed.

Supplying and laying (length perpendicular to axis of cable) un-reinforced precast concrete cable cover, ISI marked ,class LT, type 1, size 250mm x 150mm x 40mm duly embossed with "LT Cable 1100 Volts, all as specified and as directed. (Make:National/ Mehtab/ sukhi)

M & L for fine dry river sand cushioning by laying 8cm thick layer below the cable for making soft bed and 15 cm above the cable and then punning down to its consolidated thickness of 18cm after the cable is laid all as specified in SSR Part I and as directed.

Supply and lay 32 mm bore galvanised steel tubing Light grade with all fittings and fixtures laid in trench or ceiling or laying in floors complete all as directed.