K.Paramathi Block - MLACDS - 2023-2024-Construction of Community Hall at Muralai H/O Thukkachi pt

Amount

Name of the Work : Construction of Community Hall at Muralai H/O Thukkachi

Earth work excavation and depositing on bank with in initial lead of 10 m and initial lift of 2m in hard stuff clay, stiff black cotton soil, hard red earth, earth mixed with small sized boulders and hard gravelly soil as per SS 20B

Supplying and filling in foundation and basement with filling excavated earth in larges of not more than 15 thick well rammed watered and compacted including & Conveyance and all labour charges Etc.,

Cement concrete 1:4:8 mix using 40mm gauge hand broken granite tone jelly for foundation including dewaterng if found ecessary and laid in layers of not more than 15 cm thick and compacted Etc.,

Brick work in CM 1:5 mix using country bricks ground moulded of size 23 X 11 X7 cm for the following including curing etc., complete complying with standard specifications.

Supplying and erecting centering for soffits of RCC slabs of plane surface like lintels, beams Etc., including strutting 3m high using mild steel sheets of size 90cm X 60cm and B>G 10 stiffened with M.S angles of size 25mm X 25mm

Supplying fabricating and placing in position of ribbed steel roads for reinforcement to all RCC works as per the design given including cost of steel and binding wire also in all floors Etc.,

RCC 1 : 1/2 : 3 mix using 20mm ISS HBG metal for RCC items of work excluding items of works excluding centering, Shuttering and cost of reinforcement grill out including curing etc complete and also including fixing fan clamps and ixtures in rcc works wh

Plastering with cm 1:5 mix to 12mm thick including cost and conveyance of all materials in all floors etc., as directed by departmental officers etc., complete complying with standard specifications

Plastering surface of RCC items such as slabs, beams, sunshades with cement mortar 1:3-10mm thick including packing, providing cement mortar beading for sunshades staircase, steps, lands slabs etc., as directed by departmental officers etc., complete complying with standard specifications

Providing Granolythic floor finish in cement concrete 1:2:4 mixusing 10-12mm ISS metal to 20mm thick including cost and conveyance of all materials to site and all

Plastering with cm 1:4 mix to 20mm thick including cost of labour charges etc., as directed by departmental officers etc., complete complying with standard specifications

Europeon water closet with all fittings and 10 lit capacity flushing tank (Toilet)

Supplying and fixing in positon best quality and approved make Indian made white/colour glazed earthnware wash hand basin of size 550 X 400mm (with pedestal / Without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages Etc., complete complying with standeard specification and as dircted by the departmental officers.

Supplying and fixing P.V.C rainwater down fall pipe of 110mm dia with necessary shoes, bends & clamps etc.,

Paving the floor with Vetrified tiles 0.60mX0.6mX0.008m in all floors over a base layer of Cement Mortar 1:3 (One Cement and Three Sand) 20mm thick and pointed with white cement mixed with colouring pigmen

Dadooing of walls with colour glazed tiles of size 300 X 200 X 6 mm of best quality including cost and conveyance of all matrials to site and all labour charges etc.,

Flooring with following ceramic tiles of size 305 X 305 X 6 mm laid over 20mm thick cement mortar 1:3 (One Cement and Three M Sand) base mortar over the exisiting slab / floor including cutting the tiles to the required size with special cutte wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 kg/Sq.m. etc., complete complying with standard specification

Paving the floor with Anti skid step tiles 20mm thick in all floors over a base layer of cement mortar 1:3 (One Cement and Three Sand) 20 mm thick laid in-situ and pointed with same coloured cement

providing weathering course with best quality of brick jelly 20mm gauge in pure slaked lime (no sand to be added) over roof slab, the proportion of brick jelly to lime being '32 to 12.5 well beated with wooden beaters for giving required slope and thicknes

Finishing top roof mix one course machine pressed tiles of size 20 cm X 20cmX2cm approved qty with CM 1:3 , 12mm thick mixed with WPC at 2% by weight of cement used and top pointed with the same mortar Etc.,

Distembering two coats of oil bound distember using one coat of primer coat including cost and conveyance of all materials to site and all labour charges etc complete

Painting two coats with ready mixed Exterior Emulsion paint of approved quality and colour over a priming coat including through scrapping, clean removel of dirt etc.,

Painting two coats of new iron work with best quality synthetic enamel paint of approved quality and colour with priming coat including the cost all materials etc., compplete in all floors

Fabricating supply and fixing and position of MS shuter with single leave. The door outer frame will be 40X40X6mm MS angle , the shutter frame will be 35X35X6mm, MS angle intermediate stiffner will be 35X35X6 mm with cross stiffner 25X25X5 mm flats covere

Solid PVC Door shutter using 19 gauge 19mm MS sq.tubes for styles and outer frames, 15mm MS sq. Tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for paneling shall rigidly fixed in position including necessary furniture and fittings. the over all size of styles shall be 75mm X 30mm. The over all size of frames shall be 50mm X 45mm with suitable rebate for housing the shutter.

Fabricating supply and fixing and position of MS Windows with two leave. The window outer frame will be 35X35X6mm MS angle , the shutter frame will be 25X25X6mm, MS angle intermediate stiffner will be 25X25X6 mm with cross stiffner 25X25X6 mm flats covere

Supplying and fixing following electrical arrangement

Wiring with 2 X 1.5 sq.mm (22/0.3) PVC insulated SC. Unsheathed Cu. Conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories and with TW switch box and 5A F.T switch with painting of suitable colour for open PVC light point / fan point (for Electrical regulator) SD - 17 ( Light and Fan Point)

Wiring with 2 X 1.5 sq.mm (22/0.3) PVC insulated SC. Unsheathed Cu. Conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with 150X100X113mm TW switch box for 5A3 pin non inter locking CS plug with painting of suitable colour with continuous earth wire connection of 14 SWGTC wire for open PVC plug point (SD 36)

Wiring with 2 X 4 sq.mm (56/0.3) PVC insulated SC. Unsheathed Cu. Conductor cable of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with 150X100X113mm TW switch box in flush with wall with 3mm thick hylem sheet cover for 15A3 pin flush type non inter locking CS plug with painting of suitable colour with continuous earth wire connection of 14 SWGTC wire for open PVC plug point (SD 39)

Supply and run of 2X1.5 Sqm (22X0.3) PVC insulated SC unsheathed Cu. Conductor of 1100V grade on 7/20 GI Bearer Wire of service connection Mains (SD 64)

Supply and run of 2X1.5 Sqm (22X0.3) PVC insulated SC unsheathed Cu. Conductor of 1100V grade in 25mm GI pipe (Class ' B') suitably bent at both ends with necessary angle iron upright and end supports for mains (SD 69) 25MM GI Pipe

Supply and fixing of 4'36 watts Flu Fitting complete with Electronic Ballast with TW round Block on wall or ceiling with Flu Tube with PVC unsheathed copper Leads from Terminal to the Tube Light Fittings (SD 87)

Supply and fixing of 4'40 watts single street Light Flu Fitting complete with copper chok and condesor with 20mm GI pipe (CLASS "B") with one number 20mm GI bend complete on the existing post / Wall with 16 A Aerial Fuse unit on M.S plate with PVC unsheathed Cu. Leads with MS clambs with Aluminium painting with Flu Tubes Street Light Fittings (SD 94)

Supply and fixing of 1200mm (48") Sweep AC ceiling Fan complete with stepped Electronic 300 W Regulator, with 1m down rod with fan clamp with side plate and cross arm of size 450mm (18") (SD 106)

GST Amount for providing Service to Government Contract Works for the above ConstructionWorks. GST Amount is the Total GST Amount for overall quoted amount above this row in column "BB" for all works in this package} (Refer Clause 13.2 & 13.3 of Section 2 of Instruction to Bidders (ITB) of SBD)

ANNADURAI PITCHAI