Development and beautification work of Mansha Chowk.

Amount

Providing, mixing & laying Coloured RCC M25 mix with stone aggregate 20 mm ( normal size) mechanically mixed and vibrate for RCC work in designer work as per drawings and direction of Engineer in charge, excluding cost of reinforcement but including cost of centering and shuttering laid in position [ Morth specification : Clause 1000/1700]. Colour pigment should be good quality and colour, should be last for minimum 15 years with guarantee bond.

Supply & Planting of any type shady plants which can survive in the area ( Neem. Peepal, Goolar, Jamun, Imli etc. or as per the drawings and direction of Engineer - in-Charge) along road side including the following activities:- (List of name is attached) 1. Preparation of soil including cleaning & removing of unwanted shrubs removal of stones & garbage. 2. Supply of plant at site of two years of age & height more than 1.50 Mtr. 3. Supply of dry manure (Farm yard manure organic) 4. Supply of Insecticides. 5. Digging of pits size 60x60x60 cms. Including removal of stones. Manuring application of insecticides & watering at least 1.5 Liter per plant after planting or as per requirement of the Plant. 6. Guarding of Plant by any means 7. Watering to plants 8. Maintance of plants upto 5 Years by the contractor including pits, preparation of Thavala Hoeing weeding etc & application of insecticiedes etc. & security. If the plant die during maintence contractor has to replace same heingh plant at his own cost.

Supply & Panting of ornamental plants ( Kachnar, Amaltas, Gulmohar, Arjun, Kala, Siris, Jacranda etc. or as per the drawings and direction of Engineer - in-Charge) along road side including the following activities (List of name is attached) :- 1. Preparation of soil including cleaning & removing of unwanted shrubs removal of stones & garbage 2. Supply of plant at site of two years of age & height more than 1.50 Mtr. 3. Supply of dry manure( Farm yard manure organic) 4. Supply of Insecticides 5. Digging of pits size 60x60x60 cms. Including removal of stones. Manuring application of insecticides & watering at least 1.5 liter per plant after planting. 6. Waterring to Plants. 7. Maintenance of plants upto 5 Years by the contractor including pits. Preparation of Thavala Hoeing weeding etc. & application of insecticides etc. & security. If the plant die during maintencance contractor has to replace same height plant at his own cost.

Planting of shrubs Planting of shrubs in central verge or as desired location 1. Preparation of soil including cleaning & removing of unwanted shrubs removal of stones & garbage. 2. Supply of plant at site like Bouganvillia & Kaner etc. as per the drawing or direction of Engineer-in-Charge. 3. Supply of dry manure( Farm yard manure organic) 4. Supply of Insecticides 5. Digging of pits of required size for shrubs. Including removal of stones. Manuring application of insecticides & watering at least 1.5 liter per plant or as per requirement after planting. 6. Waterring to Plants.

Providing and fixing karoli Dholpur stone on centre verge and islands . Thickness of stone may vary between 25 to 40 mm. Stone fixed in 25 mm bed prepare in cement sand mortar 1:4 when it layed on horizontal, stone fixed with cement paste and with copper clamp, anchor fastner on vertical surfaces. All work done as per direction of Engineer-in-charge.

Pre-cast reinforced Cement concrete coloured tree guard:- Providing & fixing pre-cast reinforced cement concrete coloured tree guard in concrete grade M30 at project site , imposed BIDA logo (in colored) at mid of each side of tree guard. Joining and binding of all four sides to make one tree gaurd. Size of each side will be 1.8m X 0.62 m X 0.05 m. Manufactured with M-30 grade of concrete using vibro-compaction process using jointless FRP moulds so as to achieve shuttering finish. Suitably reinforced to promote long use and to prevent damage during handling, transportation & erection . All work done as per direction of Engineer in-charge.

Triangular Island Fountain:- (a)Central Water pond - 1 No. - 8m dia, Bottom Tank - Nozzles 12 Nos, Fountain Water Peak Height -10 feet, Under water cloured lights -10 Nos each in a tank, Pipe fittings, Pumps, electrical fittings and Civil works as per requirement, Tiling of inner surface of fountain pond with Tile and coping with Granite., The structure of RCC shall be made by Coloured concrete, the colour should sustained for min. 10 Years. It includes all pipes with fitting mortors, under water lights, electrical work, plumbing work, complete in all respect. (b) Side water Ponds - 2 Nos., Tank - Nozzles 1 No each, Fountain Water Peak Height / Distance -40' Thick water jet and water should not spill during flight of water and also when receiving in Central tank. Under water cloured lights -10 Nos each in a tank, Pipe fittings, Pumps, electrical fittings and Civil works as per requirement, Tiling of inner surface of fountain pond with Tile and coping with Granite., the structure of RCC shall be made by Coloured concrete, the colour should sustained for min. 10 Years. It includes all pipes with fitting mortors, under water lights, electrical work, plumbing work, complete in all respect. (c)All the visible and required surfaces shall be tiled or protected by the tiles / Granite / Marble fixed with mortar / epoxy as approved by the EIC. (d)All the drawings and specifications and methodology of working shall be vetted from the EIC before execution of Work. (e) Makes of all electric, civil and mechanical items shall be as per RUIDP SOR, PWD BSR or as decided by the EIC. (As per attached Photo)

providing & fixing of wall mounted bollard light in 8W suitable to install on wall surface. Fitting is made of pressure die cast aluminium sections with die cast base. Diffuser is made of impact resistant PMMA specially design for efficient lighting. Wall Light fixture shall have a diameter of 200mm with a height of 300mm.Colour tolerance 3 SCDM to avoid colour deviation. Nano Ceramic surface conversion, resistant to corrosive environment. Luminaire primarily coated with epoxy resin and top coated with UV stabilized powder coat and cured. All exterior parts are made of stainless steel. Silicone rubber gasket are provided for water protection. Light output of source is more than 110lm/ watt, CRI>70, operating voltage 140-270V, Fitting is IP65 with proper thermal management for longer life of fixture. Fitting is complete in all aspects with all accessories including foundation bolt. OEM Must have its own in house lab setup for testing facilities for light. Factory Inspection for testing of Light Luminaire must be done in OEM's authorised in house Labs/ outsource from government approved any authorised Lab by departmental Engineer. All as per pre approved by enginner in charge. Agency must ensure to make all necessory permission and arrangements for the visit and inspection & no extra payment shall be made for all this procedure.

providing & fixing of post light in 90W. Fitting is made of die cast aluminium closed by diffuser with durable proper silicone rubber gasket. Post top had outer diameter of 600mm and inner diameter of 345mm with attached bracket. Top light Diffuser is made of UV stabilized Opal Acrylic. Light fitting is wired with 5W led. Colour tolerance 3 SCDM to avoid colour deviation. All the LED to be tested LM80 test method. Light fixture body made of aluminium Alloy, composition having less than 0.4% copper, copper free aluminium for maximum corrosion resistance. Nano Ceramic surface conversion, resistant to corrosive environment. Luminaire primarily coated with epoxy resin and top coated with UV stabilized MRF PU PAINT and cured. All exterior parts are made of stainless steel. Light output of source is more than 110lm/ watt, CRI>70, driver efficiency > 85%, power factor > 0.9, THD<10%, Surge protection 4k, operating voltage 140- 270V. Fitting is wired with Branded OSRAM or equivalent make LED and Fulham constant current driver. Proper thermal management for longer life of fixture. Led burning of 50,000 hours. Fitting is IP66 complete in all aspects with all accessories. OEM Must have its own in house lab setup for testing facilities for light. Factory Inspection for testing of Light Luminaire must be done in OEM's authorised in house Labs/ outsource from government approved any authorised Lab by departmental Engineer. All as per pre approved by enginner in charge. Agency must ensure to make all necessory permission and arrangements for the visit and inspection & no extra payment shall be made for all this procedure.

Providing & fixing of Spot light in 30W for landscape lighting. Fitting is made of corrosion resistant die cast aluminium with LED wattage not more than 30W, CCT-3000K, CRI>70. LEDs in fixture should be of Macadam step 3 or less. Fixture to be made of 6063 aluminium alloy housing. Silicone clear gasket, SS fasteners. Mechanical resistance IK06, IP65 tempered toughened glass. This luminaire contains built-in LED modules. Operating ambient temperature range is from -15°C to +50°C. Driver efficiency >80% (integral), power factor >0.90, THD <20%, Surge protection 3KV. All exterior parts are made of stainless steel. Silicone rubber gasket are provided for water protection. Light output of source is more than 110lm/ watt, CRI>70, operating voltage 140-270V, colour temperature is 3000k. Fitting is IP66, wired with Branded OSRAM or equivalent make LED and Fulham or equivalent constant current driver. Proper thermal management for longer life of fixture. Led burning of 50,000 hours. Fitting is complete in all aspects with all accessories including foundation bolt. OEM Must have its own in house lab setup for testing facilities for light. Factory Inspection for testing of Light Luminaire must be done in OEM's authorized in house Labs/ outsource from government approved any authorized Lab by departmental Engineer. All as per pre approved by enginner in charge. Agency must ensure to make all necessary permission and arrangements for the visit and inspection & no extra payment shall be made for all this procedure.

Providing & fixing of Linear surface mounted light in 28W for façade lighting. Fitting is made of corrosion resistant Extrusion aluminum alloy with LED having elliptical beam (20 degrees’ x 50 degrees) with wattage not more than 28W, CCT- 3000K, CRI>70. LEDs in fixture should be of Macadam step 3 or less. Fixture to be made of 6063 aluminum alloy housing. Silicone clear gasket. SS fasteners. Mechanical resistance IK06, IP65 tempered toughened glass. This luminaire contains built-in LED modules. LED modules. Operating ambient temperature range is from - 15°C to +50°C. Driver efficiency >80% (integral), power factor >0.90, THD <20%, Surge protection 3KV. linear surface mounted light of length 1000mm. All exterior parts are made of stainless steel. Silicone rubber gasket are provided for water protection. Light output of source is more than 110lm/ watt, CRI>70, operating voltage 140-270V, colour temperature is 3000k. Fitting is IP66, wired with Branded OSRAM or equivalent make LED and Fulham or equivalent constant current driver. Proper thermal management for longer life of fixture. Led burning of 50,000 hours. Fitting is complete in all aspects with all accessories including foundation bolt. OEM Must have its own in house lab setup for testing facilities for light. Factory Inspection for testing of Light Luminaire must be done in OEM's authorized in house Labs/ outsource from government approved any authorised Lab by departmental Engineer. All as per pre approved by engineer in charge. Agency must ensure to make all necessary permission and arrangements for the visit and inspection & no extra payment shall be made for all this procedure.

Providing & fixing of column light made of mild steel and have ingress protection of IP66 for optical compartment. Column light of height 3 mtr above ground level with light source of 40W led light and column with predesigned lase cut to illuminate the surroundings with noticeable mode. The column light pole section of 150mmx150mm x 4mm thickness up to 3mtr long. The base plate dimension 209x209x12mm. All pole section Shall be welded by certified welders using high and MIG welding process. The Service door shall be provided at bottom part of the pole which equipped with a C clamp with sliding nuts to accommodate a built in connection box. The control gear tray is prewired with MCB, terminal connectors for loop in loop out arrangement. The base plate of the pole is design with elongated foundation holes for fine alignment of the pole during installation. Nano Ceramic surface conversion, resistant to corrosive environment. Fitting is made of mild steel with fine laser cut design tailored with lighting to suit your specific needs as per detail drawing. Luminaire primarily coated with epoxy resin and top coated with UV stabilized powder coat and cured. All exterior parts are made of stainless steel. Light output of source is more than 110lm/ watt, CRI>70, Surge protection 4k, operating voltage 140-270V, wired with Branded LEDs of Osram/ Cree and Fulham or equivalent constant voltage/current driver with efficiency>85%, power factor>0.9, THD<=10%. The CCT of led will be 3000/4000/5000 as required by the project. Proper thermal management for longer life of fixture. Led burning of 50,000 hours. Fitting is complete in all aspects with all accessories including foundation bolt. OEM Must have its own in house lab setup for testing facilities for light. Factory Inspection for testing of Light Luminaire must be done in OEM's authorized in house Labs/ outsource from government approved any authorized Lab by departmental Engineer. All as per pre approved by engineer in charge. Agency must ensure to make all necessary permission and arrangements for the visit and inspection & no extra payment shall be made for all this procedure.

providing & fixing of bollard light in 10W in 900mm height (150mm x 150mm). Fitting is made of corrosion resistant zinc plated ERW MS tubular sections with die cast base. Diffuser is made of impact resistant PMMA specially design for efficient lighting. Colour tolerance ,3 SCDM to avoid colour deviation. Nano Ceramic surface conversion, resistant to corrosive environment. Luminaire primarily coated with epoxy resin and top coated with UV stabilized MRF PU PAINT and cured. All exterior parts are made of stainless steel. Silicone rubber gasket are provided for water protection. Light output of source is more than 110lm/ watt, CRI>70, operating voltage 140-270V, Fitting is IP65 with proper thermal management for longer life of fixture. Fitting is complete in all aspects with all accessories including foundation bolt. OEM Must have its own in house lab setup for testing facilities for light. Factory Inspection for testing of Light Luminaire must be done in OEM's authorized in house Labs/ outsource from government approved any authorized Lab by departmental Engineer. All as per pre approved by engineer in charge. Agency must ensure to make all necessary permission and arrangements for the visit and inspection & no extra payment shall be made for all this procedure.

The luminaire poles are made of Durable Mild Steel. Decorative straight pole in 3mtr height. Pole section shall be of length 3mtr with diameter 114mm, thickness 4.0mm and mid- section of pole with predesigned laser cut pattern to illuminate the surroundings with noticeable mode. Designed to harmonise both in style and proportion with the designated lanterns these designer pole with predesigned format add extra ambience to the surroundings. Base plate of the pole is 200x200x12mm. Provision for inside termination box with 4way connector and 1nos. 6AMPS MCB for local isolation with cover. All pole section is welded by certified welders using high and MIG welding process. Service door at bottom part of the pole is equipped with a C clamp with sliding nuts to accommodate a built in connection box. The base plate of the pole is design with elongated foundation holes for fine alignment of the pole during installation. Rosa pole primarily coated with epoxy resin and top coated with UV stabilized powder coat and cured. Pole is complete in all aspects with all accessories including foundation bolt. OEM Must have its own in house lab setup for testing facilities for light. Factory Inspection for testing of Light Luminaire must be done in OEM's authorized in house Labs/ outsource from government approved any authorized Lab by departmental Engineer. All as per pre approved by engineer in charge. Agency must ensure to make all necessary permission and arrangements for the visit and inspection & no extra payment shall be made for all this procedure.