CMLRRP 2020-21 Phase II Eruppakuzhy mayiladumpara kurishumukku Jn road in Pattazhy GP under pathanapuram block Kollam district

Amount

RETARING AND IRISH

3.1 : Preparation of Foundation for EmbankmentScarifying Existing Granular Surface to a Depth of 50 mm by Manual Means Scarifying existing granular surface to a depth of 50 mm and disposal of scarified material with a lift upto 3 m and leads upto 1000 m as per Technical Specification Clause 301.4.

4.9 : Wet Mix Macadam <br> Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mixer (Pug Mill), carriage of mixed material by tipper to site, laying in uniform layers in sub-base/base course on a well prepared sub-base and compacting with smooth wheel roller of 80 to 100kN weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per Tables 400.11 & 400.12 and Technical Specification Clause 406. <br> By Mechanical Means with 1 km lead

75.5.5.B.2pb : Modified Penetration Macadam 75 mm thick using Bitumen S-65 - Packed Bitumen Rates <br> Construction of penetration macadam over prepared base by providing a layer of compacted crushed coarse aggregate using chips spreader with alternate applications of bituminous binder and key aggregates and rolling with a three wheel 80-100 kN static roller to achieve the desired degree of compaction as per Technical Specification Clause 506.

75.5.1.1pb : Prime Coat - Low porosity - With Packed Bitumen Rates <br> Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per Technical Specification Clause 502

75.5.2.3pb : Tack Coat - With Packed Bitumen Rates <br> Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surfaces treated with primer & cleaned with Hydraulic broom as per Technical Specification Clause 503.

75.5.2.1pb : Tack Coat - With Packed Bitumen Rates <br> Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.20 to 0.25 kg per sqm on the prepared bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503.

75.5.9.2.2.Pa : Plastic Roads - Bitumen S-65 <br> 20mm thick Open-Graded Premix Carpet using Bituminous (penetration grade/modified bitumen) Binder <br> Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508 (with 7% of bitumen replaced by shredded waste plastic) <br> Case - I By Manual Means <br> (II) Bitumen (S-65) (VG - 30)

75.5.12.A.3.2pb : Seal Coat - Manual Means - Type C - Bitumen S-65 - Packed Bitumen Rates <br> Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A, Type B and Type C as per Technical Specification Clause 510 <br> A. By Manual Means <br> Case III : Type C <br> (II) Bitumen (S-65)

od670562/2020_2021 : MorD :Surface dressing of the ground in all kinds of soil including removing vegetation and in-equalities not exeeding 15cm deep and disposal of rubbish ,lead up to 50m and lift up to 1.50m

od670561/2020_2021 : Mord: Plain cement concrete pavement ,thickness as per design,over a prepared sub base,with 43 grade&lt;br&gt;cement or any other type as per clause 1501.2.2 M 20 (grade),coarse and fine aggregates conforming to IS&lt;br&gt;383,maximum size of coarse aggregate not exceeding 25 mm,mixed in a concrete mixer of not less than 0.2&lt;br&gt;cum capacity and appropriate weigh batcher using approved mix design,laid in approved fixed side&lt;br&gt;formwork(steel channel, wedges,steel plates including&lt;br&gt;levelling the formwork as per drawing),spreading the concrete with showels,rakes,compacted using&lt;br&gt;needle vibrator and finished in continuous operation including provision of contraction&lt;br&gt;and expansion ,construction joints curing of concrete slabs for 14 days, water finishing to lines and grade as per drawing and Technical&lt;br&gt;Specifications clause 1501 (form work excluded)

3.5.1 : Excavation in Cutting in Soil by manual means with lead upto 50 mExcavation for roadway in soil using manual means for carrying of cut earth to embankment site with a lift upto 1.5 m and lead upto 50 m as per Technical Specification Clause 302.3

od670455/2020_2021 : MorD:Construction of plain cement concrete pavement,thickness as per design,over a prepared sub base with 43 grade cement or any other type as per clause 1501.2.2M20 (grade),coarse and fine aggregates conforming to IS 383,maximum size of coarse aggregate not exceeding 25mm,mixed in a concrete mixer of not less than 0.20cum capacity and appropriate weigh batcher using approved mix design,laid in approved fixed side form work(steel channel,wedges,steel plates including levelling the formwork as per drawing),spreading the concrete with showels,rakes,compacted using needle vibrator and finished in continuous operation including provision of contraction and expansion ,construction joints curing of concrete slabs for 14days,water finishing to lines and grade as per drawing and technical Specification clause1501(formwork incuded)

od694153/2020_2021 : Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads on Bituminous Surface @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes. (Modified morth 8.13)

10.4.A.3 : Direction and Place Identification signs with size more than 0.9 sqm size board<br> A. Retro-reflectorised Traffic Signs <br>3 Providing and erecting direction and place identification retro- reflectorised sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3, fixed over aluminium sheeting, 2 mm thick with area exceeding 0.9 sqm supported on RCC Posts 100 mm x 100 mm firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per approved drawing and Technical Specification Clause 1701

od674473/2020_2021 : Supplying and fixing name board of size 70x50cm installed in the appropriate place visible to the public made of masonry wall with granite plaque should be inscerted and including engraving letters etc. complete the direction of departmental officers at site.

N V AJAYAKUMAR

SAMSON SAMUEL

JESMIN T MANALITHARA

Krishnakumar Krishnan Nair

Bidder Name

N V AJAYAKUMAR

B MADHU

Krishnakumar Krishnan Nair

SAMSON SAMUEL

JESMIN T MANALITHARA