CERTAIN MISC REPAIRS TO OTM AND MD ACCN AND REPAIR TO LEAKAGE SEEPAGE IN BLDGS SUNKEN FLOOR REPAIR TO TOILET SHAFTS CHAJJAS BALCONY ROOF SHEETS REPAIR TO SANITARY FITTINGS TILING PLINTH PROTECTION PLASTERING AT ZONE-1 ZONE-1A AND ZONE 2 UNDER GE(S)

Amount

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15cm thick above or below ground level.Complete all as specified and as directed.

Dismanting wall /ceiling board (Fibre pulp insulation) or insulation boards any thickness including cover filters.Complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding(but not backing) complete and removing rubbish off the premises.complete all as specified and directed.

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar complete all as specified and directed.

Dismanting timber scantling 40 Sqcm and over in secion in any position in framed work complete all as specified and directed

Dismanting timber scantling under 40 Sqcm in secion In fillests, rails , posts, refters and purlins etc in any position in framed work or unframed work.Complete all as specified and as directed.

Dismantling Structural steel work includings door, gates, etc and similar works complete all as directed

Dismantling asbestos cement corrugated semi corrugated etc sheets in roof covering.Complete all as specified and as directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar.Complete all as specified and as directed.

M&L for old size sub Class B bricks, straight or curved on plan exc 6 m mean radius built in cement mortar ( 1:6) having compressive strenght not less than 75 kg/Sq cm all as specified and directed.

All as per item No 10 above but except bricks all as sepcified and directed

Material and labour for old size sub Class B bricks bricks, straight or curved on plan to any radius in half brick thick wall built in cement mortar ( 1:4) having compressive strenght not less than 75 kg/Sq cm all as specified and directed.

Taking down chowkats or frames not exc 1.5sqm each with shutters( without taking off shutters from the frame ) including dismantling of PCC bed blocks for hold fasts.Complete all as specified and as directed.

Taking down chowkats or frames exc 1.5sqm and not exc 4.0 sqm each with shutters ( without taking off shutters from the frame ) including dismantling of PCC bed blocks for hold fasts.Complete all as specified and as directed.

Taking down of shutters of any description exc 1.00 Sqm and n.exc 2.00 sqm each.Complete all as specified and as directed.

Taking down of shutters of any description n.exc 1.00 Sqm and each.Complete all as specified and as directed.

Refixing of shutters of any description exc 1.00 Sqm and n.exc 2.00 sqm each in same opening including of taking down, easing, adjusting and renewal/refixing of builders hardware as required including renewal of unserviceable screws, etc.Complete all as specified and as directed.

Refixing of shutters of any description n. exc 1.00 Sqm each in same opening including of taking down, easing, adjusting and refixing/renewal of builders hardware as required including renewal of unserviceable screws, etc.Complete all as specified and as directed.

S & F louvers /Precast RCC Jalli, 35mm thick (measured solid) including all moulding in PCC 1:2:4 type B0 (using 12.5 graded aggregate) set in cement mortar 1:4 including dismantaling complete all as specified

Material and labour for providing Plain Cement Concrete (1:3:6) type C1 using 20mm graded aggregate as in bed block or hold fast all as specified and directed.

S&F 2nd class hard wood plain, solid, striaght chowkats and framed rebated on the solid rounded or chamfered put together with glue pinned at joints including making rebate for fixing second shutter as per site requirement.Complete all as specified and as directed.

S&F 35 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides.Complete all as specified and as directed.

Supply and fix 35mm thick second class hard wood glazed and skeleton, open rebated and prepared to receive glass/ wire cloth, gauze exc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. The sizes of members of shutters as per IS-1003 (Part-2), kiln seasonable and chemically pressure treated and fitted to chowkhats complete all as specified and directed. (Note : Glass / wire cloth wil be measured and paid separately).Complete all as specified and as directed.

S&F factory made solid PVC door frame of size 50mm x 47 mm made out of 5mm plain coloured PVC sheet reinforced with MS square tube.Complete all as specified and as directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tube for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC stiles and plain colour PVC sheets for top rail, lock rail bottom rail on either side & as gap insert for top rail & bottom rail panneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stile & rails with suitable PVC sheet beading & jointed together with solvent cement all as specified and directed.

S&F 100mm size Stainless steel Butt hinges.Complete all as specified and as directed.

S&F 75mm size type C-21 Butt hinges extruded aluminium alloy with galvanised MS sheet hinges pin anodised.

S&F in repairs extruded aluminium alloy handels fabricated type, anodised, 150mm long.Complete all as specified and as directed.

S&F in repairs extruded aluminium alloy handels fabricated type, anodised, 100mm long.Complete all as specified and as directed.

S&F Aluminium anodised sliding door bolts of size 250 mm long, with hasp & staple ( bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extreded sections or cast aluminium alloy.Complete all as specified and as directed.

S&F Aluminium anodised barrel tower bolts of extruded section 200 mm long and fixed with screws.Complete all as specified and as directed.

S&F Aluminium anodised barrel tower bolts of extruded section 150 mm long and fixed with screws.Complete all as specified and as directed.

S&F in repair MS helical door spring 150 mm size incl roller and roller plate fixed to wooden or steel frames with welding etc complete all as specified and directed.

S&F in repairs 100 mm Hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F steel windows with side hung shutter including projecting type hinges with steel handle and steel peg stay, complete with glazing bars, donetailed or welded all as soecified and directed.

S&F steel window with side hung shutter, including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified.

Supply and fix, steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples.Complete all as specified and as directed.

S&F in repairs Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples

S&F 4 mm thick frosted/ pin headed glass in ventilator shutters incl hacking out all as specified and directed

S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.50 sqm in each pane for any type of window up to tripple story bldg incl hacking outcomplete all as specified and directed.

S&F in repair of pre-laminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work thickness of 12 mm complete all as specified and directed.

Material & Labour in repairs 19/20 mm thick Block boards, Exterior grade, laminated sheet with decorative face, veneer on one face, commercial type fixed with screws to timber frame work complete all as specified and directed.

S & F Continuous (piano) hinges, 30 mm width of flaps ,mild steel, bright finish or electrogalvanised complete all as specified and directed.

S&F bal catches with 8 mm dia steel ball magnet catches for cuboard shutter including strking plate as approved etc complete all as specified and as directed

S&F as in repair 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished all as directed

M&L 2nd class Hard Wood in scantling fixed clean swan in framed work complete all as specified and directed

M&L 2nd Class Hard Wood plain fillets square, rectangular in section clean sawnn sectional area exe 13 sqcm & n.exe 25 sqcm fixed with nails including one coat of black oil.

S&F in repairs stainless steel curtain rod of 20/25 mm bore incl brackets and end knobs for door and window complete all as specified and directed.

S&F in repairs brass decorative type curtain brakets and end cap complete all as specified and directed.

Supply & Fix in repairs floor door stopper of brass body and tongues with hard drawn steel spring, overall length cover plate 150mm complete all as specified and directed

S&F Exposed GI powder coated snap grid frame for false ceiling 600x600mm size of wall angle 25x25x0.55mm size of cross tee and main tee 26x24x0.55mm and 32mm x 24mm x 0.55mm with 3mm dia single GI adjustable suspentor including supply and fixing of 4mm thick E Board decorative type in false ceiling including fixing arrangement from steel tress any type of tress.Complete all as specified and as directed.

Fixing only in repairs for 4 mm thick E Board decorative type, fixed to timber/ GI/ Aluminium framework in ceiling flat/ sloping all as specified and directed.

S&F 0.5mm thick pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet of any colour ,tensile strength of 550Mpa as in roof covering ,cladding to wall ,ridge,gutter etc fixed with self tapping screwsComplete all as specified and as directed.

All as per item No.54 above but plain sheet for ridge ,gutter etc fixed with self tapping screws as specified.

S&F 6 mm thick asbestos cement corrugated or semi corrugated sheets in roofs, walls etc fixed with 'L' type or 'J' type or cranked book bolts. Complete all as specefied and directed.

S&F of joist, channel, angle, flat iron or Tee sections, fixed independently with connecting plates, etc confirming to Fe 410-W (Gde 250 quality A) complete all as specified and directed.

Supply & Fix framed works such as grills grating etc with ends of bars shouldered and for rivetted in forged into spikes, framed guard bars, railing and similar work confiring to Fe-410-0 or Fe 310-0 complete all as specified and directed

Checking of joinery (wooden/steel) iron/aluminium mongery, pelmet box, door springs etc requiring carpentry work and carrying out minor repairs such as tightening of screws/nails, fixing glass panes, minor adjustment of joinery, door etc. including petty repairs material like screws/nails, plug, wood adhesive and make good by paint to match exixting surfaces etc. to make it functional complete all as specified and directed. (Note: Any items required to be replaced shall be paid under respective items).

Taking down plaster, plaster work for patches, tiling work, filling of cement morter in holes, joints, joinery (wooden/steel) iron/aluminium, pelmet box, etc requiring masonary work and carrying out minor repairs such as patches plaster, tiles, brick, filling etc. including petty repairs material like cement, sand, aggregate, tiles etc. to make it functional complete all as specified and directed. (Note: Any items required to be replaced shall be paid under respective items of Sch 'A'/BoQ).

Repair windwos like steel/wooden/aluminium by using wire mesh and easing windows shutter by using oil,greesing or cleaning cement morter or removing old rust, dust,mud etc make it good and smooth incl. one steel handle to openable in a normal process. Complete all as specifiesd and as directed

M&L for Closing bolt holes etc. in old corrugated steel sheets or Aluminium sheeting by sealing with one bitumen and one curved GI washer on either side and 6mm G.I. bolts and nuts, all set in stiff white lead, bolt n exc 25mm in length.Complete all as specified and as directed.

M&L for Bitumastic gola, with 80/25 bitumen and coarse sand mixture. 1:3 by weight, 8cmx8cm at the junction of roofing to vertical surfaces.Complete all as specified and as directed.

M&L 25 mm thick PCC type B-1, 1:2:4 (20mm graded aggregate) as in sub base/floor etc as a levelling course complete all as specifed and as directed.

M&L Vitrified Ceramic tiles 8 to 10 mm thick (square/ rectangular) of any shade, polished, area of each tiles exceeding 0.42 but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:6.Complete all as specified and as directed.

All as per item No 65 above but in skirting over 10mm thick screeding in cement mortar 1:4

M&L Vitrified Ceramic tiles 9 to 10 mm thick (square/ rectangular) light shade, polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:6.

All as per item No 67 above but in skirting over 10mm thick screeding in cement mortar 1:4

M&L Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:6.Complete all as specified and as directed.

M&L Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:6.Complete all as specified and as directed.

S&F Coloured Glazed ceramic tiles 450 x 300 mm x 6 to 7mm thick, in skirting /dado etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm rendering in Cement mortar 1:4.Complete all as specified and as directed.

M&L for Vitrified parking tiles of any colour/patern 30cm x 30 cm x 8 to 10 mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigments in floors and over 15 mm thick screed bed in CM 1:4 for laying floor finishes.Complete all as specified and as directed.

M&L for Chequered cement concrete tiles of size 300 x 300 x 25 mm thick with grey cement and pigment, set and jointed and pointed in neat cement slurry in floors laid over & including 15 mm thick screed bed in cement mortar 1:6 all as specified and as directed.

M/L Granite (of any type) tiles 18-20 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete over 15mm thick screed bed in CM 1:6 over cooking platform.Complete all as specified and as directed.

M&L 18-20 mm thick Granite (of any type) tiles machine cut, in skirting/ dado laid over cement screed and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete over 10mm thick screed bed in CM 1:4.Complete all as specified and as directed.

M&L Marble (green /white) work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade.Complete all as specified and as directed.

M&L for Machine cut kota stone slab flooring 20-25mm thick over 20mm thk cement screed base in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing.Complete all as specified and as directed.

M&L for Machine cut kota stone slab 20-25mm thick in riser of steps, skirting, dado over 10mm thk cement screed base in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing.Complete all as specified and as directed.

M&L for Cuttitting and polishing only to existing kota stone surface incl filling joing with pigment and cement etc with beeswax polishing.Complete all as specified and as directed.

M&L 75 mm thick PCC 1: 3:6 type C2 using 20mm graded agg finishing even and smooth without using extra cement as in plinth protections/path and laid fair in alternate bays n including filler joints with sealing compound grade 'A' where required complete all as specifed and as directed.

M&L 40 mm thick,Cement concrete, type B-1, (1:2:4), 20 mm graded aggregate as in floor making finished even and smooth using extra cement.Complete all as specified and as directed.

M&L for PCC 1:2:4 (using 12.5mm graded aggr) in roof Kerbs,rounded or chamfered or haunching in chajjas to prevent water seepage into brick walls,including necessory formwork and scafolding upto a height of 8mtr including demolition of existing PCC all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position.Complete all as specified and as directed.

M&L for RCC type B1 1:2:4 (20 mm graded agg) as slab supported on wall , beams columns in floor, roofs landing and the like.Complete all as specified and as directed.

S&F Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Use & Waste of Formwork to sides and soffits of floor or roof beam , beam haunching, girders ,lintels shevles inclusidng support and hangs.Complete all as specified and as directed.

Taking down cement plastering on brick or stone walls etc, including raking out joints, hacking for key scrubbing down with water etc.Complete all as specified and as directed.

M&L rendering 15 mm thick cement plaster on brick wall in CM 1:4 mixed with WPC @ 3% by weight of cement and finished even and smooth without using extra cement complete all as specified and as directed. (Note : WPC will be measured and paid for separately)

M&L 10mm thick rendering in cm (1:6) on fair faces of brick work or concrete surfaces and finished even and smooth without using extra cement.Complete all as specified and as directed.

M&L for 5 mm thick rendering in cement mortar 1:3 on concrete surfaces as on ceiling and finished fair and even complete all as specified and directed.

Supply only water proofing compound. Conforming to IS -2645.Complete all as specified and as directed.

M&L preparation of newely plaster surfaces and appplying two coats of Acrylic exterior paint (Anti fungal paint) over a coat of damp shealth primer and a coat of 1 mm thick wall care putty by smart painting method and as per manufacturer and apllied by approved applicator.complete all as specified and directed.

M&L Applying two coats of acrylic distemper to newly plastered/previously untreated wall surface over a coat of 1 mm thick layer of wall care putty over a coat of wall primer by smart painting method including preparation of newly platsered wall all as specefied and directed.

Material and labour for applying three coats of white wash on walls including preparation of new or previously untreated surfaces all as specified and directed.

M&L for preparation of new plastered or unplastered surfaces of ceiling and applying three coats of white wash as in ceiling complete all as specified and directed.

Taking down existing damaged water closet alongwith complete PCC from sunken floor and providing new EWC / IWC and water proofing treatment to sunken floor as per following stage :- (i) 15mm thick plastering in CM (1:2) with WPC at all around and base of sunken floor with proper slope. (ii) Applying a coat of 85/25 gde hot bitumen @ 0.7Kg/Sqm over a coat of bituminous primer @0.5Kg/Sqm and then pasteing of 150 micron polythene film / 3mm APP membrane, natural colour with cold cut back adhessive. (iii) Providing cement concrete to fill up the sunken floor (PCC 1:4:8) after testing of water tightness.

Taking down existing aluminium shutter of area exc 1.0 Sqm but not exc 2.00 Sqm and refixing the same in the same opening after reparing and make functional including replacement of fitting and fixture for proper functioning as required all as specified and as directed.

S & F In repairs Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty all as specififed and directed

S & F in repairs Aluminium (extruded section body type )door closer hydraulically regulated designation No 3, universal type , suitable for door shutter of 851 to 1000 mm in width and of weight and weight betwwen 61 to 80 kg ordinary rat tail rod pattern springs, including roller and roller plate complete all as specified and directed

S&F Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F Anodised aluminium window (two/three track) sliding type without sash bar and ventilator shutters ((lower type),aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc.complete all as specified

S&F Anodised aluminium door shutter aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 02 Nos in each door , hinges ,anodised aluminium snap beading, screws etc.complete all as specified

S&F 4 mm thick heat absorbing/tinted glass of any size with aluminium bedding and complete all as specified and directed.

Checking and attending to water leakage from taps, flushing cisterns, wash hand basins and other sanitary fittings/fixtures and any obstruction to water supply, requiring plumber work and carryout minor repairs such as replacement of washers, check nuts, tightening of fittings of flushing cistern etc including petty materials like washers of all sizes, thread(shoot), M-seal, screws, nails to make water supply/ plumbing lines functional and leak proof complete all as specified and directed. (Note: Any items required to be replaced shall be paid under respective items).

Supply and fix,as in repair,15 mm bore pillar tap, fancy type cast copper alloy, with quarter turn head, chromium plated, screwed down high pressure, with or without letter Hot or Cold with long screwed shanuls and fly nuts, screwed for iron pipe or for brass ferrule all as specified and directed.

Supply and fix,as in repair, 15 mm bore bib taps, cast copper alloy,cromium plated, fancy type, with quarter turn handle, screwed down, screwed for iron pipe or for brass ferrule all as specified and directed.

Supply and fix,as in repair, pillar tap standard of PTMT any colour screwed, for iron pipe 15mm bore (minimum weight 90 gms) all as specified and directed.

Supply and fix, as in repair, bibtap standard of PTMT any colour screwed, for iron pipe 15mm bore (minimum weight 90 gms) all as specified and directed.

Supply and fix, as in repair, Shower rose PTMT 40 mm dia with neck of 600mm long standard colour screwed, for iron pipe 15mm bore all as specified and directed.

S&F in repairs kitchen plate rack made out of stainless steel 0.63 mm thick sheet with partitions and size of rack 900 x 800 x 250 mm with shape and pattern as per sample kept in Sample room of GE Office complete all as specified and directed. Nirali /Anjali/Prayag/Bluestar

Supply and fix, as in repairs, sheet glass self assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with cromium plated bracket guard and railing 60cm long all as specified and directed.

Supply and fix, as in repair, vitreous china wash down water closet pan (Pedestal pattern) white (excluding flushing cistern and flush pipe) including seat cover white closed type complete all as specified and directed

Supply and fix, as in repairs, vitreous china squatting pan of Orrisa pattern size 580mm x 440 mm, white, with integral foot rests (excluding flushing cistern and flush pipe) including connection making good to floor all as specified and directed.

Supply and fix, bowel urinal flat back of size 465 x 355 x 265mm (minimum), white, with grating and union for discharge pipe, (excluding flushing cistern, flush pipe and waste pipe) complete including providing and fixing plugs, bedding urinals against wall in cement mortar (1:2) securing urinals to plugs with and including 60 mm brass screws and pointing around urinals back in cement all as specified

Supply and fix, as in repairs, plastic water closet seat, closed pattern with flat bottom, and cover for water closet pan (padestal pattern) all as specified and directed.

S&F in repair brass choromium plated towel rail 600 mm long complete all as specified and directed.

S & F in repairs Toilet paper holder of brass chromium plated fixed to walls with chromium plated brass screws.Complete all as specified and as directed.

S&F in repair Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F in repair 15mm bore dia brass choromium plated wall mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed.

S&F in repairs bathroom mirror cabinet size of 450 x 350 mm with all necessary fittings complete all as specified and directed.

S&F in repairs center hole basin mixer without pop-up waste system complete all as specified and directed.

S&F in repair Towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms) complete all as specified and directed.

Supply and fix, as in repair, stop valve, cast copper alloy, fancy type, chromium plated with long shank and cup (concealed type) screwed down high pressure, with crutch or butterfly handles for 15 mm bore pipe or for unions all as specified and directed.

S&F in repairs stop cock cast copper alloy, fany type ,chromium plated, screwed down, high pressure, with crutch of butterfly handle screwed both ends to iron pipe of size 15mm, all as specified and directed.

S&F in repairs angle cock 15mm bore, two way, chromium plated, fixed to GI or steel tubing incl fittings complete all as specified and directed.

S&F in repairs bib cock 15mm bore, two way, chromium plated, fixed to GI or steel tubing incl fittings complete all as specified and directed.

Supply and fix, as in repair, vitreous china wash basin, white, flat back size 580 x 450 mm, excluding taps, waste chain, plug and porcelain stopper but including brackets, cutting for and pinning in ends of bracket or erecting stand complete all as specified and directed.

Supply and fix, as in repair, sinks with drainage board made out of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortor to dwarf wall or including fixing cantiriver lever brackets and connecting union to pipe overall size 915mmX460mm and bowl size 410mmX330mmX160mm all as specified and directed.

S&F sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm all as specified and directed.

Supply and fix,as in repair, waste coupling CP 32 mm dia for glazed ware basins etc with fly nuts flanged etc complete all as specified and directed.

Supply and fix,as in repair, 32/40 mm dia PTMT 610 mm long waste pipe suitable for WHB complete all as specified and directed.

Supply and fix,as in repair, CP 40mm dia waste coupling with inlet and out let screwed for pipe or connections including packing, union and cap etc complete all as specified and directed.

S&F in repairs stainless steel grating 100/75mm dia all as specified and directed.

Supply and fix, as in repair, Overhead Shower 100 mm Round / Square Shape Single Flow (Brass Chromium Plated) with Rubit Cleaning Syste, including fixing to steel pipe or union of 15mm bore all as specified and direcetd.

Supply and fix, as in repairs, Hand Shower (Health Faucet) (Brass chromium plated) with 1 Meter Long Easy Flex Tube in Chrome Finish & Wall Hook complete all as specified and as directed.

Supply and fix, as in repair, 10 ltrs capacity PVC valve less syphonic action type, low level flushing cistern, white, with inlet, ball valve float and handle including brackets & flush pipe of polyethylene of low or high density or PVC 32 mm dia complete all as specified and directed.

Supply and fix, as in repair,15 mm dia 600 mm long connection pipe with two PVC PTMT nuts at each ends with rubber washer complete all as specified and directed.

Supply and fix, as in repair, steel handles for steel window for left and right side shutter all as specified and directed

Taking up or down 15 mm bore old steel tubing and connections, including disconnection of fittings from tubing including cleaning for re-fixing or removal from site complete all as specified and directed.

All as per item No 140 here in before but 20 mm bore.

S&F of 15 mm bore tubes medium grade galvanised with and incl all GI fitting (such as bends, elbows, Tees, connectors, short pieces, back nuts, unions, caps and plug etc ) and fixed complete to wall and ceiling or laid in/on floor complete all as specified and directed,

All as per item No 142 here in before but 20 mm bore.

Supply and fix,as in repairs, 75 mm dia of outlet PVC(SWR) floor trap, plain with grating including jointing with solvent cement all as specified and directed

Supply & fix radiant door bottom sealing strip guard (door seal) complete all a specified and directed.

Demolition of old damaged existing water proofing compound on RCC roof of any description and specification and cleaning the surface thoroughly all as specified and directed

M & L 15 mm thick in cement mortar (1:4) on existing roof surface true to level with WPC @3% of cement after applying cement slurry @3Kg/Sqm and applied coat of hot blown bitumen of graded 85/25 @1.2 Kg/Sqm.Complete all as specified and as directed.

Supply and laying 3mm thick APP based Polymeric membrane of approved manufacture with weight not less than 3.60 Kg per Sqm reinforced with non-woven polyster febric weight not less than 150gms per Sqm.The overlap shall be not less than 100mm on transverse direction and 75mm on longitudinal direction and sealing overlaps and Applying evenly one coat of aluminium paint @ 0.10 liter per square metre over the APP based polymeric membrane complete all as specified and as directed.

Disconnecting existing tanks exc 500 n exc 1000 ltr, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. (Cleaning repairing, etc. measured separately).Complete all as specified and as directed.

M&L one coat of white wash on old wall surfaces of walls and cornices including preparation of old plastered or un plastered surafce by brooming down or steel wire brushing ,srcaping down smoke soot ,moulds ,moss and efflorescent salts and trading oil and greasy spot all as specified and directed

M&L one coat of white wash on ceiling and cornices including preparation of old plastered or un plastered of surafce of ceiling by brooming down or steel wire brushing ,srcaping down smoke soot ,moulds ,moss and efflorescent salts and trading oil and greasy spot all as specified and directed

M&L Applying one coat of acrylic distemper by smart painting method to old wall surfaces of walls and cornices including preparation of old plastered or un plastered of surafce of wall by brooming down or steel wire brushing ,srcaping down smoke soot ,moulds ,moss and efflorescent salts and trading oil and greasy spot all as specified and directed

M&L preparation and cleaning of existing painted wall surfaces and appplying one coats of Acrylic exterior paint (Anti fungal) paint by smart painting method including properly fillings the cracks with wall care puty complete all as specified and directed

M&L complete removal of existing treatment and Applying two coats of Acrylic Emulsion distember to old plastered/previously untreated wall over a coat of 1 mm thick layer of wall care putty over a coat of wall primer.Complete all as specified and as directed.

M&L complete removal of existing treatment and appplying two coats of Acrylic exterior paint (Anti fungal) paint over a coat of damp shealth primer over a coat of 1 mm thick layer of wall care putty by smart painting method to old plastered walls as per manufacturer and apllied by approved applicator complete all as specified and directed.

M&L for one coat of exterior emulsion floor coating paint aesthetic glossy finish complete all as specified and directed.

M&L for complete removal of existing treatment and plaster by the use of wire brush and applied a coat of Dr fixit super latex with cement ratio of 1:1.5 in both horizontal and vertical direction after that applied Dr fixit super latex with water complete all as specified and directed by Engr-in charge .

Material and labour for preparation of new and previously un-treated wood and wood base surfaces of any description, not otherwise described over 10cmwidth or girth and applying two coats of synthetic enamel paint over one coat of pink primer all as specified and directed.

M&L prepration of new steel surface and applying two coats of synthetic enamel paint over one coats of red oxide preparation of new surfaces over 10 cm width on ginth.

M&L for applying for preparation of old painted surfaces of wood and woodbase surfaces of any description , not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint all as specefied and directed.

M&L for applying for preparation of old painted surfaces of old painted steel surfaces and iron surfaces of any description ,over 10cm width or girth incl and applying one coat of synthetic enamel paint all as specefied and directed.

S&F 18/19mm thick plywood grade A (Termite treated / water proof) ,type BB fixed with screws to timber /iron frame work as in cupboard, drwer, kitchen cabinate etc .Complete all as specified and as directed.

M&L for 0.9 mm thick decorative choice of lamination type -1 of surface finish , colour and pattern as approved fixed with adhesive or aral Dite epoxy resin Hetex or fevicol etc as per manufacturers instructions complete all as specified.

M&L FOR DAMPROOFING AGAINST RISING DAMPNESS ON INTERNAL SIDE OF WALL preparation surface including, apply a series of Berger HS Wall Shield 2K,Waterproof Putty & Seal-O-Prime on the damp surface of internal wall up to minimum height of 1 ft from the area effected from rising dampness. Apply 3mm thick polymer modified cement mortar (1:3) admixed with Berger HS Latex Plus @ 10 kg per bag of cement on bare brick/concrete surface. Application process involve for damp proofing 1. Apply 2 coats of HS Wall Shield 2K @ 10 sqft/kg. 2. Apply 9mm plaster (1:3) admixed with Berger HS Cementmix Plus @ 200ml per bag of cement. NOTE: Once the plaster get fully cured apply Berger HS waterproof putty and Seal-O- Primer instead of normal putty and primer befores painting for long time performance.

M&L FOR DAMPROOFING AGAINST RISING DAMPNESS ON EXTERNAL SIDE OF WALL preparation surface including, apply a series of Berger HS Wall Shield 2K & HS Damp Shield Elasto on the damp surface of internal wall up to minimum height of 1 ft from the area effected from rising dampness. Apply 3mm thick polymer modified cement mortar (1:3) admixed with Berger HS Latex Plus @ 10 kg per bag of cement on bare brick/concrete surface. Application process involve for damp proofing 1. Apply 2 coats of HS Wall Shield 2K @ 10 sqft/kg. 2. Apply 12 mm plaster (1:3) admixed with HS Cementmix Plus @200ml per bag of cement. NOTE: Once the plaster get fully cured apply Berger HS Damp Shield Elasto instead of waterproof/ normal putty and primer before painting.

Dismantling and breaking up PVC drain pipes of any dia taking out of trenches/ fixed to wall/ laid in floor etc complete all as specified and directed.

Supply and fix, 110mm bore PVC (SWR)pipe single socketed with rubber ring joints fixed to walls all as specified and directed.

S&F in repairs PVC (SWR) 110mm dia bends any radius all as specified and directed.

S&F in repairs PVC (SWR) branch 110mm bore pieces, single ( single Y ) equal or unequal all as specified and directed.

S&F in repairs PVC (SWR) junction110mm bore single ( single t) equal or unequal all as specified and directed.

Supply and fix, PVC cowls 110 mm bore all as specified and directed.

Supply and fix, 75 mm bore PVC (SWR)pipe single socketed with rubber ring joints fixed to walls all as specified and directed.

S&F in repairs PVC (SWR) 75 mm dia bends any radius all as specified and directed.

S&F in repairs PVC (SWR) branch75 mm bore pieces, single ( single Y ) equal or unequal all as specified and directed.

S&F in repairs PVC (SWR) junction75 mm bore single ( single t) equal or unequal all as specified and directed.

Supply and fix, PVC cowls 75 mm bore all as specified and directed.

Excavation in trenches n.exc 1.5 m wide and n.exc 1.5 m deep for sewage pipe line etc. and getting out in soft/loose soil all as specified and as directed by Engr-in-Charge.

Returning, filling in, including spreading leveling watering and well ramming in layers n,exc 25 cm thick in soft /loose soil for sewage pipe line /manhole and cleaning the site complete all as specified and as directed.

Removing excavated materials n.exc 50 mtr and depositing where directed at level n.exc 1.5 mtr above the starting point complete all as specified and directed.

fixing only , 110 mm bore PVC (SWR)pipe single socketed with rubber ring joints fixed to walls or laid in trenches or floor all pipe all as sepcified and directed

fixing only, 75 mm bore PVC (SWR)pipe single socketed with rubber ring joints fixed to walls or laid in trainches or floor all as sepcified and directed

M&L for refixing of steel gate including welding, cutting of hinges and welding/ replacing hinges of steel sections after raising gate hight up/ down to make clearance from bottom or in same place area of gate not exc 3 sqm of each side complete all as specified and directed. Note: Steel member shall be measured and paid seperately)

M&L 10-12mm thick clear toughened glass inluding fixing stainless steel brackets, cleats and fixing accessories for frame less toughened glass fixing in fixed opening as per manufacture's instructions and approval of garrison engineer.

S&F in repair vitreous china premium/1st qualit wash dwon water closet Single Piece EWC with/ivory/off white (closed pattern incl all necessary accessories like rag blts/gel gasket etc) including 10liters capacity vitreous china valveless syphonic action type flushing cistern low level white, with inlet ball valve float and hanle including brackets complete all as specified and directed.

S&F 08 mm thick curved shaped urinal partition with frosted glass of size 900x450 mm including fixing accessories, fixing bolt, etc complete all as specified and directed. cat part No JSC-CHR-810UC450X of make Jaquar as per approval of GE

S&F in repair sensor (battery operated) for urinal pot including battries and all fittings and fixture complete all as specified and directed for model Number STL-51087 of Jaquar.

S&F composite 100% solid wood plastic complete (single extended process) material with density not less than 780 kg/cum and plastic wood as in wood chowkhat complete all as per manufacturer instruction.Complete all as specified and as directed.

S&F 5 mm thick mirror with decorative frame of size of face size 40 to 50 mm mounted on 10 to 12 mm water proof plywood and fixed in to chromium plated / stailess steel cup washers of approved pattern as directed by Engr-In-charge complete all as specified and as directed.

S&F in repair vitreous china counter type Basin size 500X435X180 mm, excluding taps, waste chain, plug and porcelain stopper but including brackets, cutting for and pinning in ends of bracket or erecting stand complete all as specified and directed. Model: KUS-WHT-35601 of Make Jaquar

S&F 32mm bore brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and ditected

Checking to sensor based auto flusher concealled type urinal pot sensor incl refixing/ change of battries if required and make functional in all respect all as specified and directed.

M&L Providing and laying 60 mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand.Complete all as specified and as directed.

S&F in repair Auto Closing urinal valve alloy CP with wall flange (push type) for 15mm bore Model No:PRS-CHR-077 ,Make: Jaquar. Note 1:-The contract sum shall be arrived at after deducting amount of schedule of credit from the total quoted amount. Note 2-Contractor's supervisor and main worker would wear shirt/T-shirt of colour sky blue/brown/yellow preferable embossed with contractor's firm name while carrying out any activities in defence area for better check of security purpose. Note 3:-The tenderer (all eligible contractors) shall ascertain the taxes & levies as on date. The subject tender caters all the taxes & levies as on date including the latest notification of GST issued as on date ( issued by Central Board of Indirect Taxes and Customs)

AVASANA SOLUTIONS PRIVATE LIMITED

M/S KAUSHICK CONSTRUCTION

M/S Manjit Singh