SPECIAL REPAIRS TO BLDG No. T-81, T-82 AND T-172 OF FD WKSP COY, PROVN OF CERTAIN REVENUE AND MINOR WORKS AT DIFFERENT LOCATIONS OF ALONG MIL STN UNDER GE 872 EWS

Amount

B/R SERVICES/WORKS

Demolition Cement Concrete (un-reinforced) of any description in Ground Floors, Pavings, etc. not exc. 150mm thickness (above or below Ground Level) and removing debris, etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Demolition Brick Work or Pre-cast Concrete Block Masonry, built in Cement Mortar and in any Position including all Quoins, Arches and Pillars, etc., complete all as specified and as directed.

Dismantling Timber Scantling 40 Sq Cm and Over in Section in Unframed Work, complete all as specified and as directed.

Dismantling Timber Fillets, Rails, Posts, Rafters, Purlins, etc. Under 40 Sq Cm in Section in Unframed Work, complete all as specified and as directed. NOTE : Taking down/ out of Forking Pieces fixed with Scantlings, Boarding, Studs, etc. will not be Measured separately for Payment.

Taking down Chowkat or Frame of any description (without Taking Off Shutter from the Frame) not exc. 1.50 Square Metre Each, complete all as specified and as directed.

Taking down Chowkat or Frame of any description (without Taking Off Shutter from the Frame) of any description, exc. 1.50 Square Metre but not exc. 4.00 Square Metre Each, complete all as specified and as directed.

Dismantling Plain or Corrugated Steel Sheeting of any gauge and thickness, Segregating the Serviceable Steel Sheeting, stacking properly at Sites and keep in Safe Custody for re-use, complete all as specified and as directed.

Dismantling Wall and Ceiling Boards (Fibre, Pulp, Insulation, etc.) or Insulation Boards/ Slabs/ Blankets of any descriptions including Cover Fillets, complete all as specified and as as directed.

Dismantling Floor, Hearth or Wall Tiling including Cement Mortar Bedding (but not backing) and removing debris, etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Taking down Cement Plaster including raking out Joints, hacking for Key, scrubbing down with Water and removing Debris, etc. etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Hacking/Taking out Broken Glass of any description from Wooden or Metal Frames, or Stone, Concrete or Brick surrounds of any thickness or size; Hacking out Old Putty or Removing Beads, etc., complete all as specified and as directed,

Surface Excavation not exc. 30 Cm deep and ave. 15 Cm deep and getting out in Soft/Loose soil, complete all as specified and as directed.

Excavation in Over Areas, not exc. 1.50 Metre in depth and getting out as in Soft/ Loose Soil, complete all as specified and as directed.

Excavation in Over Areas, exc. 1.50 Metre and not exc. 3.00 Metre in depth and getting out as in Soft/ Loose Soil, complete all as specified and as directed.

Excavation in Trenches not exc. 1.50 Metre wide and not exc. 1.50 Metre in depth for Foundation etc. or for Shafts, Wells, Cess Pits, Manholes, Pier Holes, etc. not exc. 10 Sqm on Plan and not exc. 1.50 Metre in depth and getting out as in Soft/Loose Soil, complete all as specified and as directed.

Returning, Filling in including Spreading, Levelling, Watering and Well Ramming in layers not exc. 25 Cm, in Soft/Loose Soil, complete all as specified and as directed.

Removing Excavated Materials (Soils) not exc. 50.00 Metre and depositing where directed at a level not exc. 1.50 Metre above the Starting Point, complete all as specified and as directed.

Excavating in Post Holes (or similar Holes) in Soft/Loose Soil, each not exc. 0.50 Cum, getting out including spread and levelled with excavated surplus Soils, complete all as specified and as directed.

M&L Sand Filling (as approved) under Floors or in Foundations in layers not exc. 15 Cm thick including Watering and Consolidation, complete all as specified and as directed.

M&L Hardcore broken Stone or Boulders, gauge not exc. 63mm, deposited, spread and levelled in layers not exc. 15 Cm thick, watered and well rammed to a True surface, complete all as specified and as directed.

M&L Cement Concrete 1:4:8 (40mm graded aggregate) in Foundations, Filling and Mass Concrete, etc. including necessary Formwork, complete all as specified and as directed. NOTE : Cost of Formwork shall deem to be included in the Quoted Unit Rate.

M&L Cement Concrete 1:2:4 (20mm graded stone aggregate) in Coping, Bed Plates, Benching, Bed Block, Kerb Stones, etc. including necessary Formwork and Weathering, slightly Rounded or Chamfered Angles and Throating, complete all as specified and as directed. NOTE : Cost of Formwork shall deem to be included in the Quoted Unit Rate.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Foundation including Rafts, Footing, Foundation Beams for Column Basement Slab, under Reamed Piles, complete all as specified and as directed. NOTE : Reinforcement will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Walls, Retaining Walls, Basement Walls, Ballast Walls and the like; any thickness; above Top of Footings; including attached Pilaster and Buttresses, complete all as specified and as directed. NOTE : Reinforcement will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Beams, Cantilevers, Bressumers, Lintels over 1.50 Metre Span, etc., complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Slabs supported on Walls, Beams and Columns in Floors, Roofs, Landings, Balconies, Canopies, Deck Slabs and in Shelves and the like, complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Pre-cast Reinforced Cement Concrete 1:2:4 (20mm graded aggregate) in Landings, Cover Slabs (for Manholes, etc.), Chullah Hoods, Chajjas, Water Troughs, Mangers, Shelves and Similar Articles with Plain faces and Setting in Cement Morter 1:4, complete all as specified and as directed. NOTE : Reinforcement will be Measured and Paid for separately under appropriate Items.

M&L Formwork to Sides of Concrete Foundations, Footings, Bases of Columns, Raft and Raft Beams, Sides and Soffits (if any) of Foundation and Plinth Beams; and Similar Work; Vertical or to Batter, Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Faces of Walls, Retaining Walls, Abutments, Parapets and Staircase Railings and Similar Work including attached Pillasters, Buttresses, etc.; Vertical or to Batter, Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Sides and Soffits of Floor or Roof Beams, Girders, Beam Haunchings, Bress-summers, Lintels, Cantilevers, Shelves including Supports, Overhangs, etc. also splays between Floors and Beams, etc., Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Soffits of Suspended Slabs such as Roof Slabs, Floor Slabs, Landings and Similar Works; not exc. 200mm thick (Horizontal or Sloping), etc., Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Edges of Concrete Flats, Treads, Breaks in Floors, Window Cills, Concrete Railings, Openings in Concrete Walls, Floor and Roofs not exc. 20 Cm Wide and Sides of RCC/PCC Bands in Walls, Horizontal or Sloping and Similar Work, exc. 10 Cm but not exc. 20 Cm Wide, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Pre-cast Cement Concrete 1:3:6 (20mm graded stone aggregate) Block Masonry with Solid Blocks, exc. 10 Cm in Width, Setting in Cement Mortar 1:6, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (12.5mm graded stone aggregate) 40mm thick in Damp Proof Courses to Horizontal or Vertical Surfaces including Use & Waste of Formwork and Applying evenly a coat of Blown type Bitumen @ 1.50 KG/SQM and blinding with Clean Dry Sand @ 0.05 CUM/SQM, complete all as specified and as directed.

M&L Cutting Chases, Pinning in. Making Good to facings where required on Brick Walls and Pointing in Cement Mortar 1:3 to Ends or Edges of Landings, Steps, Cills, Sunshades, Shelves, Lintels, etc.; and Cutting not exc. 10 Cm girth, complete all as specified and as directed.

M&L Cutting Holes in Brick Walls, not exc. Half Brick thick, built in Cement Mortar for inserting of Holdfasts, Lugs, etc. and Making Good to dismantled portion with Cement Concrete 1:3:6 (20mm graded stone aggregate) or Cement Mortar 1:3 (as required) and adjoining Surfaces in Cement Mortar 1:4, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) in Scantling, Cleansawn, Timber fixed (Unframed work), fixing with Nails, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Fillets, Plain on One Side, Square, Rectangular or Triangular in Section, exc. 13 Sq Cm but not exc, 25 Sq Cm (Studs of size 50x50mm), fixed with Nails, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Fillets, Plain on One Side, Square, Rectangular or Triangular in Section, exc. 6.0 Sq Cm but not exc, 13 Sq Cm (Forking Piece of size 25x25mm), fixed with Nails, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Plain Fillets, Wrought, Square, Rectangular or Triangular in Section, exc. 3.0 Sq Cm but not exc. 6.0 Sq Cm, fixed with Nails, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Plain, Solid, Straight, Chowkats and Frame, Wrought, Framed rebated on the Solid, Rounded or Chamfered, put together with Glue pinned at Joints, complete all as specified and as directed.

S&F Flush Shutter 30mm thick, Solid Core Construction with Block Board core and Plywood Face Panels, Commercial type on Both Sides including Teakwood Lipping 6.0mm thick, fixed with Nails, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Panelled Shutter 35mm thick (any number Panels) Plain, Framed with Lock Rails, having Panels of 12mm thick Veneered Particle Board medium density, Wood Particle Board with Commercial Face Veneers and fitted to Chowkat, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Glazed and Skeleton Shutter 35mm thick, Open rebated and prepared to receive Glass, Gauze, etc. (without Sash Bars), Edges of Framing plain, chamfered or rounded. fitted with cut and mitred Beads for securing glass, etc.; sizes of Members of Shutters as specified in SSR Part I, Section 8, Clause 8.24(a) and fitted to Chowkat, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Glazed and Skeleton Shutter 30mm thick, Open rebated and prepared to receive Glass, Gauze, etc. (without Sash Bars), Edges of Framing plain, chamfered or rounded. fitted with cut and mitred Beads for securing glass, etc.; sizes of Members of Shutters as specified in SSR Part I, Section 8, Clause 8.24(a) and fitted to Chowkat, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Glazed and Skeleton Shutter 30mm thick, Divided into Squares, with plain, chamfered or rounded, mitred and rebated Sash Bars to receive Gauge/Glass, any numbers, sizes of Members of Shutter as specified in SSR Part-I, Section 8, Clause 8.24(b) and fitted to Chowkat, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Small Fittings such as Brackets of any type, Latch and Hinge Blocks, Shaped Door and Window Stops and the like, including all necessary Labours; Articles not exc. 200 Cu Cm Each, complete all as specified and as directed. NOTE : Butt Hinge will be Measured and Paid under appropriate Item as 'Supply only'.

S&F Factory made Solid PVC Door Frame of size 50x47mm made out of 5.0mm thick Plain Colour (Ivory Shade) PVC Sheet reinforced with Mild Steel Square Tube and fixing in opening as per Specification and Drawing of MES Schedule Part-II, complete all as specified and as directed.

S&F Factory Made Solid PVC Moulded Door Shutter with Particle Board Core 28mm to 30mm thick (Stiles) with 2, 4 or 6 Raised Panel Design with 2.0mm thick Moulded PVC Sheet on the Front Face and 2.0mm Plain Colour PVC Sheet on Back Face, fitted in Frame at Site as per Specifications & Drawings, complete all as specified and as directed.

M&L Factory Made Solid Panel PVC Door Shutter 30mm thick (Style) Plain colour (Ivory shade) consisting of Frame made out of Mild Steel Tubes for Top and Bottom Rails, Mild Steel Frame shall be covered with heat moulded wood grain PVC ‘C’ Channel having a PVC Sheet Strip of 20mm width stuck inside with Solvent Cement for Stiles and wood grain PVC Sheets for Top Rail, Lock Rail & Bottom Rail on either side and as gap insert for Top Rail & Bottom Rail, Panelling of wood grain PVC Sheet to be fitted in the Mild Steel Frame welded/sealed to the Stiles and Rails with suitable 5mm thick x 15mm wide PVC Sheet beading used inside Stiles and Rails and decorative PVC Beading of 10mmx10mm (90) and jointed together with Solvent Cement and fixing in the Frame at Site, complete all as specified and as directed.

M&L Anodised Aluminium Powder Coated (Thickness of Powder Coating not less than 50 micron) Frame for Doors, Windows, Ventilators with One or More Rebates including Joining Cleat for fixing, etc., complete all as specified and as directed.

M&L Anodised Aluminium Window and Ventilator Shutters, Side Hung type without Sash Bars, Aluminium Sections weighing 0.55 KG/RM including necessary Joining Cleats, Glazing Clips, Rubber Packing, Anodised Aluminium Snap Beading, Screws, Anodised Aluminium Fittings such as Peg Stays 150mm long (1 No.). Hinges Type B-21, 100mm long (2 No.) suitable Handle (1 No.), complete all as specified and as directed.

S&F Aluminium anodised Barrel Tower Bolt of size 125mm long (as approved), Extruded Section, complete all as specified and as directed.

S&F Aluminium anodised Barrel Tower Bolt of size 150mm long (as approved), Extruded Section, complete all as specified and as directed.

S&F Aluminium anodised Barrel Tower Bolt of size 200mm long (as approved), Extruded Section, complete all as specified and as directed.

S&F Aluminium alloy, anodised, Sliding Door Bolt 250mm long (as approved) with Hasp, Staple (Bolt type) and Fixing Clips of Sheet, Cast or Extruded Sections and Fixing Bolts and Sliding Bolts of Extruded Sections or Cast-Aluminium alloy and fixed, complete all as specified and as directed.

S&F Aluminium alloy, anodised, Sliding Door Bolt 300mm long (as approved) with Hasp, Staple (Bolt type) and Fixing Clips of Sheet, Cast or Extruded Sections and Fixing Bolts and Sliding Bolts of Extruded Sections or Cast-Aluminium alloy and fixed, complete all as specified and as directed.

Supply only Stainless Steel Butt Hinge of size 50mm (as approved), complete all as specified and as directed.

S&F Stainless Steel Butt Hinge of size 75mm (as approved), complete all as specified and as directed.

S&F Stainless Steel Butt Hinge of size 100mm (as approved), complete all as specified and as directed.

S&F Aluminium Handle of size 125mm (as approved), anodised, Cast type, complete all as specified and as directed.

S&F Aluminium Handle of size 150mm (as approved), anodised, Cast type, complete all as specified and as directed.

S&F Floor Door Stopper with Overall length of Cover Plate 140mm of Aluminium Alloy Body and Tongue (as approved) anodised, with Hard Drawn Steel Spring, fixed in Floor, complete all as specified and as directed.

S&F Mild Steel 300mm, Ordinary Rat Tail Rod pattern Springs including Roller and Roller Plate, complete all as specified and as directed.

S&F Stainless Steel Drapery Rods (Curtain/Harrison Rails) having 24mm Outer dia, fixing with and including Brackets, Stops, Rollers, Side Holders, etc, and Fixed-in-repairs, complete all as specified and as directed.

S&F Stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm and fixed with Stainless Steel Wire Staples, complete all as specified and as directed.

S&F Stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm and fixed with Stainless Steel Wire Staples and Fixing-in-repairs, complete all as specified and as directed.

S&F Sheet Glass 3.0mm thick, Plain, Ordinary quality and Glazing with Oil Putty in Square not exc. 0.50 Sqm in Each Pane, complete all as specified and as directed.

S&F Figured Glass 4.0mm thick, Pin Headed and Glazing with Oil Putty in Square not exc. 0.50 Sqm in Each Pane, complete all as specified and as directed.

S&F Sheet Glass 5.5mm thick, Plain, Ordinary quality and Glazing with Oil Putty in Square, exc. 0.50 Sqm in Each Pane, complete all as specified and as directed.

S&F Solar Control Film 50 Micron Reflective type Sticked to Glass Panes of any size and thickness as per Instructions of Manufacturers, complete all as specified and as directed.

M&L TMT Bars 10mm dia and Over, cut to length, bent to shape required including cranking, bending spirally for hooping for Columns, hooking Ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L TMT Bars 8mm dia, cut to length, bent to shape required including cranking, bending spirally for hooping for Columns, hooking Ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L TMT Bars 8mm dia in Stirrups, Spacers and Binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L Mild Steel Round Bars 10mm dia and Over, cut to length, bent to shape required, including binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L Mild Steel Bands, Straps, Supports or Stays for Rainwater, Ventilating Pipes including Bolts, Hooks (Stay) for large Gates; Hook and Pintle Hinges: large Hasps and Staples; Hand Made Sliding Bolts; Clamps; Holdfasts; Wall Ties and similar small Articles conforming to Fe-290 Gde-E-165, complete all as specified and as as directed.

M&L Mild Steel Hand Rails, Half Round or Other Stock Section or Core for Wooden Hand Rail Straight portion, drilled and countersunk for Balusters Running Bars, for Doors, Balusters, Nosing to Steps including embeding in Concrete and screwing, etc. Wind Ties for Roof including securing Bolts; Posts and Struts in Fencing including cutting Tops to shape as directed, drilling holes, notching for Wire, etc.; Flat Iron Fillets (for securing Wire Mesh etc.) including all necessary drilling, bolting or riveting, etc., and Similar Work, conforming to Fe-290, Gde E-165, complete all as specified and as directed.

M&L Mild Steel Framed Work such as Grills, Gratings, etc, with Ends of Bars shouldered and/or riveted, or forged into Spikes; Framed Guard Bars, Barred Iron Doors, Ladders, Framed Balusters, Walkways, Railings, Frame Work of Water Tanks and Similar Works, conforming to Fe-290, Gde E-165, complete all as specified and as directed.

M&L Rolled Mild Steel in Joist, Channel, Angle, or Tee Sections in Vertical Post, conforming to Fe-410-W (Gde E-250) Quality 'B', fixed independently, without Connecting Plates, etc. (cut to ordinary lengths i.e. within 20mm of the Length indicated), complete all as specified and as directed.

M&L Rolled Mild Steel Sections in Main and Cross Beams, Hip & Jack Rafters, Purlins where connected to Common Rafters, Running Rails and Guides for Sliding Doors, conforming to Fe-410-W (Gde E-250), Quality 'A', fixed with Angle Cleats or other Connecting Plates, complete all as specified and as directed

M&L Plates (Plain or Chequered) Channels, Square cut or notched (Ordinary and Counter Sunk) forming Holes, without any attachment, conforming to Gde Fe-410-W (Gde E-250) Quality 'B', complete all as specified and as directed.

M&L Mild Steel Screw Bolts (machine made) of any description or size, with Hexagonal or Square Heads at One End and screwed the Other End, or screwed Both Ends, Each screwed End to be fitted with Washers and One Hexagonal or Square Nut, complete all as specified and as directed.

M&L Running Welding in Repairs in Steel Works, thickness of metal to be welded not exc. 6.0mm, complete all as specified and as directed.

S&F Corrugated Mild Steel Sheeting 0.63mm thick, Galvanised @ 120 Gram Per Sqm, with Two Corrugation Side Lap, fixing with and including L-type or J-type Cranked Hook Bolts with Washer, etc., complete all as specified and as directed.

M&L Refixing Galvanised Corrugated Mild Steel Sheeting 0.63mm thick (Serviceable Steel Sheets obtained from Item No. 1.007 here-in-before) with Two Corrugation Side Lap, fixing with and including L-type or J-type Cranked Hook Bolts with Washer, etc., complete all as specified and as directed.

S&F Plain Mild Steel Sheeting 0.80mm thick, Galvanised @ 120 Gram Per Sqm, in Ridges, Hips, Valley Gutters, etc., fixing with and including L-type or J-type Cranked Hook Bolts with Washer, etc., complete all as specified and as directed.

M&L Refixing Galvanised Mild Steel Sheeting 0.80mm thick Plain (Serviceable Steel Sheets obtained from Item No. 1.007 here-in-before) in Ridges, Hips, Valley Gutters, etc., fixing with and including L-type or J-type Cranked Hook Bolts with Washer, etc., complete all as specified and as directed.

S&F Pre-painted Galvalume Aluminum Zinc Coating GI based Corrugated Steel Sheet 0.50mm thick Coloured, having Tensile Strength of 550 Mpa in Roof Covering, Cladding to Walls, fixed with Aluminum Self Tapping Screws and Aluminum Washers of suitable Size, complete all as specified and as directed.

S&F HSPC Non-Asbestos Fibre Cement Building Boards 4.0mm thick, fixed to Timber Frame Work with Screws, complete all as specified and as directed.

S&F Plywood Board 6.0mm thick, Grade BWR, Type BB, fixing with Mild Steel Screws to Timber frame Work, complete all as specified and as directed.

M&L Cement Concrete 1:4:8 (40mm graded stone aggregate) 75mm thick in Sub-base to Floors, etc., complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (20mm graded stone aggregate) 40mm thick in Flooring, etc., laid in Alternate Panels, finished Concrete Surfaces Even and Smooth with using Extra Cement, complete all as specified and as directed.

M&L Glass Dividing Strips 38mm Wide and 3.0mm thick and inserted in Position, conform to Design, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (12.5mm graded stone aggregate) 25mm thick as Base Course for laying Tiles on Flooring, etc., finished Concrete Surfaces Fair and Even, complete all as specified and as directed.

M&L Non-skid Ceramic Coloured Tiles 7.0mm to 8.0mm thick (Square/ Rect-angular), Area of Each Tile exc. 0.06 Sqm but not exc. 0.11 Sqm (1st quality) in Floors, Jointed in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, laid over and including Cement Screed Bed 15mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Non-Skid Ceramic Coloured Tiles 7.0mm to 8.0mm thick (Square/ Rect-angular), Area of Each Tile exc. 0.11 Sqm but not exc. 0.18 Sqm (1st quality) in Floors, Jointed in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, laid over and including Cement Screed Bed 15mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Non-Skid Ceramic Coloured Tiles 7.0mm to 8.0mm thick (Square/ Rect-angular), Area of Each Tile exc. 0.11 Sqm but not exc. 0.18 Sqm (1st quality) in Vertical Surfaces i.e. Dado, Skirting, etc., set in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, fixing over and including Cement Screed Bed 10mm thick in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Non-Skid Ceramic Coloured Tiles 7.0mm to 8.0mm thick (Square/ Rect-angular), Area of Each Tile exc. 0.18 Sqm but not exc. 0.38 Sqm (1st quality) in Floors, Jointed in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, laid over and including Cement Screed Bed 15mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Vitirified Coloured Ceramic Tiles 10mm thick (Square/Rectangular) in Light shade, Polished, Area of Each Tile not exc. 0.36 Square Metre in Floors, etc., Set and Jointed in Neat Cement Slurry and pointed in White or Coloured Cement to match the Tiles, laid over and including 15mm thick Cement Screed Bed in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Vitirified Coloured Ceramic Tiles 10mm thick (Square/Rectangular) in Light shade, Polished, Area of Each Tile not exc. 0.36 Square Metre in Floors, etc., Set and Jointed in Neat Cement Slurry and pointed in White or Coloured Cement to match the Tiles, laid over and including 15mm thick Cement Screed Bed in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Glazed Ceramic Coloured Tiles 300x200x6.0mm to 7.0mm thick (1st quality) in Vertical Surfaces i.e. Dado, Skirting, etc., Set in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, fixing over and including Cement Screed Bed 10mm thick in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Glazed Ceramic Coloured Tiles 350x250x7.0mm or 450x350x7.0mm thick (1st quality) in Vertical Surfaces i.e. Dado, Skirting, etc., Set in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, fixing over and including Cement Screed Bed 10mm thick in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Granite (of any type) Work 20mm thick, (Table Rubbed and Polished) in Steps, Jambs, Pillars, Window Cills, Cooking Platforms and like in Cement Mortar 1:4 including Pointing in White Cement 1:2, using Marble Dust with Admixture of Pigment to match with Shade of Granite, fixing over and including Cement Screed Bed 15mm thick in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Cement Concrete 1:3:6 (40mm graded stone aggregate) 75mm thick in Plinth Protection, etc., Laid in Alternate Panels, finished Concrete Surfaces Even and Smoooth without using Extra Cement, complete all as specified and as directed.

M&L Joint Filling in Plinth Protection with 1 Part of Bitumen and 3 Parts of Sand, complete all as specified and directed.

M&L Rendering (Internal) 10mm thick in Cement Mortar 1:6 on Brick/ PCC Blocks or Concrete Works, finished Plastered Surfaces Even and Smooth without using Extra Cement, complete all as specified and as directed.

M&L Rendering (External) 15mm thick in Cement Mortar 1:4 on Brick/PCC Blocks or Concrete Works including mixed with WPC, finished Fair and Even, complete all as specified and as directed. NOTE : Water Proofing Compound (WPC) will be Measured and Paid saperately under appropriate Item.

M&L Rendering 15mm thick on Brick/PCC Blocks or Concrete works consisting in 2 layers, Backing/Under layer of 10mm thick in Cement Mortar 1:6 and Float/ Top layer 5.0mm thick in Cement Mortar 1:4 including mixeing WPC to Float/ Top layer, finished Fair and Even, complete all as specified and as directed. NOTE : Water Proofing Compound (WPC) will be Measured and Paid saperately under appropriate Item,

Supply only Water Proofing Compound (as approved), conforming to IS:2645-2003, complete all as specified and as directed.

M&L Preparing New Plastered Surfaces of Walls and applying Three Coats of White Wash, complete all as specified and as directed.

M&L Preparing Old Treated Plastered Surfaces of Walls including Brooming down or Steel Wire brushing, Scrapping down Smoke Soot, Moulds, Moss and Efflorescent Salts, Trading Oil and Greasy Spots on Walls and applying One Coat of White Wash, complete all as specified and as directed.

M&L Preparing Old Treated Plastered Surfaces of Walls including Brooming down or Steel Wire brushing, Scrapping down Smoke Soot, Moulds, Moss and Efflorescent Salts, Trading Oil and Greasy Spots on Ceiling and applying One Coat of White Wash, complete all as specified and as directed.

M&L Preparing New Plastered Surfaces of Walls and applying Two Coats of Colour Wash over a Coat of White Wash, complete all as specified and as directed.

M&L Preparing New Plastered Surfaces of Walls and applying a Layer of Wall Care Putty 3.0mm thick on Plastered Surfaces of Walls including Cutting and Rubbing down to obtain a Even and Smooth Surface, complete all as specified and as directed.

M&L Applying Two Coats of Distemper Oil Emulsion (of approved Tint) over a Coat of Chalk Whitening (Priming Coat), complete all as specified and as directed.

M&L Preparing Old Treated Plastered Surfaces of Walls and applying One Coat of Distemper Oil Emulsion (of approved Tint), complete all as specified and as directed.

M&L Complete Removal of Existing Surfaces Treatment on Walls and applying Two Coats of Distemper Oil Emulsion (as approved Tint) over a Coat of Chalk Whitening (Priming Coat), complete all as specified and as directed.

M&L Preparing Newly Plastered Surfaces of Walls and applying Two Coats of Cement Based Paint (of approved Tint) over a coat of Alkali Resistant Priming Paint, complete all as specified and as directed.

M&L Preparing Old Treated Surfaces on Walls and applying One Coat of Cement Based Paint (of approved Tint), complete all as specified and as directed.

M&L Complete Removal of Existing Treatment on Walls and applying Two Coats of Cement Based Paint (of approved Tint) over a coat of Alkali Resistant Priming Paint, complete all as specified and as directed.

M&L Preparing New Wooden Surfaces of any description, over 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint) over a Coat of Pink Primer, complete all as specified and as directed.

M&L Preparing Old Painted Wooden Surfaces of any description, over 10 Cm in Width or Girth and applying One Coat of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint), complete all as specified and as directed.

M&L Preparing New Wooden Surfaces of any description, not exc. 10 Cm in Width or Girth when unconnected with other Painting or when Painted in different Tint and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint) over a Coat of Pink Primer, complete all as specified and as directed.

M&L Preparing Steel and Iron Surfaces of any descriptions, over exc. 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint) over a Coat of Red Oxide Zinc Chrome Primer, complete all as specified and as directed.

M&L Preparing Old Treated Steel and Iron Surfaces of any descriptions, over exc. 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint), complete all as specified and as directed.

M&L Preparing Old Treated Steel and Iron Surfaces of any descriptions, over exc. 10 Cm in Width or Girth and applying One Coat of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint), complete all as specified and as directed.

M&L Preparing Steel and Iron Surfaces of any descriptions, not exc. 10 Cm in Width or Girth when unconnected with other Painting or when Painted in different Tint and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint) over a Coat of Red Oxide Zinc Chrome Primer, complete all as specified and as directed.

M&L Preparing New or Previously Treated Surface of Wood and Wood based Materials of any description and girth and treated with Two Coats of Creosote Oil, complete all as specified and as directed.

M&L Preparing Newly Painted/ Treated Brick, Stone, Concrete or Plaster Surfaces, Area not exc. 0.50 Sqm Each and applying One Coat of Synthetic Enamel Paint (Black or as approved Tint) as Base Surface Area for Writing Letters, etc., complete all as specified and as directed.

M&L Stencil Writing Letters or Figures (Block. Roman, Italic or Indian) of height exc. 150mm and not exc. 300mm with White Synthetic Enamel Paint over Black Base Surfaces, complete all as specified and as directed.

M&L Stencil Writing Stops, Commas, Short Lines, Dashes, Hyphens, Brackets, etc. with White Synthetic Enamel Paint over Black Base Surfaces, complete all as specified and as directed.

M&L Preparing previously Untreated Surfaces of Wood and Wood Based Materials, of any description and girth not otherwise described and treating with Tar or Coal Tar Black Paint to Backs of Chowkats, etc. Area tarred exc. 0.10 Sqm but not exc. 0.50 Sqm Each including Sanding with Clean Sharp Sand after tarred, complete all as specified and as directed.

M&L Preparing previously Untreated Surfaces of any description and girth not otherwise described and treating with Tar or Coal Tar Black Paint to Holdfast or similar Small Items, Area tarred not exc. 0.10 Sqm Each including Sanding with Clean Sharp Sand after tarred, complete all as specified and as directed.

S&F Galvanised Steel Tubing 15mm bore (dia), medium grade, conforming to IS-1239 with all Fittings, fixed to Walls, Ceiling or laid in Floors, complete all as specified and as directed.

S&F Galvanised Steel Tubing 20mm bore (dia), medium grade, conforming to IS-1239 with all Fittings, fixed to Walls, Ceiling or laid in Floors, complete all as specified and as directed.

S&F Bib Tap 15mm bore (dia) Cast Copper alloy, Chromium Plated, Fancy type, with Crutch or Butter-fly Handle, screwed down, screwed for Iron Pipe or for Brass Ferrule, complete all as specified and as directed.

S&F Bib Tap 15mm bore (dia) Cast Copper alloy, Chromium Plated, Fancy type, with Long Screwed Shanks and Fly-nuts, screwed down, screwed for Iron Pipe or for Brass Ferrule, complete all as specified and as directed.

S&F Pillar Tap 15mm bore (dia), Cast Copper alloy, Chromium Plated, Fancy type, with Capstan Heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with Long Screwed Shanks and Fly-nuts, screwed for Iron Pipe, complete all as specified and as directed.

S&F Stop Valve 15mm bore (dia), Cast Copper alloy, Chromium Plated, Fancy type, screwed down, high pressure, with Crutch or Butter-fly Handle, screwed both Ends for Iron Pipe or for Unions, complete all as specified and as directed.

S&F Stop Valve 15mm bore (dia), Cast Copper alloy, Chromium Plated, Fancy type, with Long Shank and Cup (Concealed type) screwed down, high pressure, with Crutch or Butter-fly handle, screwed both Ends for Iron Pipe or for Unions, complete all as specified and as directed.

S&F PTMT Angle Stop Valve 15mm bore (dia) having Minimum Weight 90 Gram of any Colour, high pressure, screwed both Ends for Iron Pipe or for Unions, complete all as specified and as directed.

S&F Gun Metal Globe/Gate Valve 20mm bore (dia) with Iron Wheel Head, screwed both Ends for Iron Pipe, complete all as specified and as directed.

M&L Vitreous China White Squatting Pan of size 580x440mm, Orissa Pattern with Integral Foot Rests, ‘P’ or ‘S’ Trap, providing Joints between Flush Pipe and Socket of WC Pan, Cones, India Rubber (nozzles of WC Pan) incluiding provision of Lime Concrete Bedding and Making Good to Floor/distrubed surfaces, complete all as specified and as directed.

S&F Vitreous China White Wash Down Water Closet Pan (Pedestal Pattern) with PVC (SWR) ‘P’ or ‘S’ Trap and Fixing Bolts and Making Good to Floor/ Distrubed Surfaces in Cement Mortar 1:3, complete all as specified and as directed.

S&F White Plastic Water Closet Seat and Cover for Water Closet Pan (Pedestal Pattern), Closed Pattern with Flat bottom and Cover and Mild Steel Chromium plated or Aluminised Hinging Device, complete all as specified and as directed.

S&F Chromium Plated Fancy type Health Faucet Cardiff with 1.0 Metre Stainless Steel Hose/ Tube & Hook of Brass, conforming to MAKE : PRAYAG, Model No. DROPLETS, Cat No. BEA-85 or equivalent Model (as approved by GE) of Approved Make, complete all as specified and as directed.

S&F Vitreous China White Toilet Paper Holder of Approved size, fixed on Walls with Wooden/ PVC Cleats and Brass Chromoum Plated Screws, complete all as specified and as directed.

S&F PVC Flushing Cistern 10 Litre capacity White, Low Level, Valveless, Syphonic Action type with Inlet, Ball Valve, Float and Handle, and PVC Flush Pipe 32mm bore (dia), a pair of Cast Iron Brackets Erecting Stand duly painted including cutting and pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3, complete all as specified and as directed.

S&F Vitreous China White Wash Hand Basin 550x400mm in size, Flat Back with Brass Chromium Plated Waste Fitting 32mm bore (dia) and PVC Waste Pipe 32mm bore (dia) including a Pair of Cast Iron Brackets Brackets Erecting Stand duly painted including cutting and pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3, complete all as specified and as directed.

S&F Sink with Drainage Board made of Stainless Steel l.0mm thick Kitchen or Laboratory of Overall size 915x460mm with Bowl size 410x330x160mm with Plugs, Washers and Wastes; including Bedding in Cement Mortar to Dwarf Wall or including Fixing Cantilever Brackets and Connecting Union to Pipe, complete all as specified and as directed.

S&F Brass Chromium plated Bottle Traps 32mm bore (dia) for Wash Basins with Inlet and Outlet, screwed for Pipe or Connections including necessary Packing, Union and Cap and fixed, complete all as specified and as directed.

S&F PVC Connection Pipe 15mm in size and 450mm in length with PTMT Nuts, complete all as specified and as directed.

S&F PVC Connection Pipe 15mm in size and 600mm in length with PTMT Nuts, complete all as specified and as directed.

S&F Brass Chromium plated Shower Rose 125mm size, with or without Swivel Joints, including fixing to GI/ Steel Pipe 15mm bore (dia) or Union, complete all as specified and as directed.

S&F Brass Chromium plated Overhead Shower Rose 70mm dia, Round in shape, Single Flow (ABS Body of Chromium plated with Gray Face Plate) with Rubit Cleaning System with 240mm Arm & Flange including fixing to 15mm bore (dia) GI/ Steel Pipe, complete all as specified and as directed. MAKE : JAQUAR, Shower Model No. ALLIED, Cat No. EOS - 491) Arm Model No. ALE-536A or equivalent Model (as approved by GE) of Approved Make

S&F Wall Mixer (Minimum Weight of Valve as per SSR or in relevant IS) with 'L' Bend 115mm long, Full System Cast Copper alloy, Brass Chromium plated, suitable for mixing Hot & Cold Water for Bathing, screwed down for 15mm bore (dia) GI/ Steel Pipe, complete all as specified and as directed. MAKE : JAQUAR, Model No. APR-ESS-101273 or equivalent Model (as approved by GE) of Approved Make

S&F Soap Dish not less than 125mm in size, Chromium plated, Fancy type (as approved), fixed on Wall with Wooden/ PVC Cleats and Brass Chromoum Plated Screws, complete all as specified and as directed.

S&F Sheet Glass Shelf Assembly consisting of 5.5mm thick Sheet Glass, Shelf 12 Cm Wide with Chromium plated Bracket Guard and Railing 60 Cm long, fixed on Wall with Wooden/ PVC Cleats and Brass Chromoum Plated Screws, complete all as specified and as directed.

S&F Tubular Towel Rail 20mm dia, Brass Chromium Plated, D-type, 60 Cm long between Flanges with Bracket (One Pair), fixed on Wall with Wooden/ PVC Cleats and Brass Chromoum Plated Screws, complete all as specified and as directed.

S&F PTMT Grating Doom 100mm dia (Minimum weight 25 Gram) Plain including Jointing with Solvent Cement, complete all as specified and as directed.

S&F PVC (SWR) 75mm bore (dia) Trap having Diameter of Outlet in 75mm, Plain with Grating including Jointing with Solvent Cement, complete all as specified and as directed.

S&F Cast Iron Floor/Nahani Trap having Diameter of Outlet in 50mm, with Grating including Jointing to Waste Pipe fixed in Cement Concrete 1:2:4 (20mm graded stone aggregate), complete all as specified and as directed.

S&F PVC (SWR) 75mm bore (dia) Pipe, Single Socketed, in any length with Rubber Ring Joints, laid in Floors or fixing to Walls, etc. with suitable Clamps, complete all as specified and as directed.

S&F PVC (SWR) 110mm bore (dia) Pipe, Single Socketed, in any length with Rubber Ring Joints, laid in Floors or fixing to Walls, etc. with suitable Clamps, complete all as specified and as directed.

S&F PVC (SWR) Bend any type 75mm bore (dia), provided with Access Door, etc., jointing with Solvent Cement, complete all as specified and as directed.

S&F PVC (SWR) Bend any type 110mm bore (dia), provided with Access Door, etc., jointing with Solvent Cement, complete all as specified and as directed.

S&F PVC (SWR) Vent Cowl 75mm bore (dia), jointing with Solvent Cement, complete all as specified and as directed.

S&F PVC (SWR) 110mm bore (dia) Pipe, Single Socketed, in any length with Rubber Ring Joints, laid in Trenches and Tested after laid, complete all as specified and as directed. NOTE : Earth Works will be Measured and Paid for separately under appropriate Items.

S&F PVC (SWR) 160mm bore (dia) Pipe, Single Socketed, in any length with Rubber Ring Joints, laid in Trenches and Tested after laid, complete all as specified and as directed. NOTE : Earth Works will be Measured and Paid for separately under appropriate Items.

M&L Cement Concrete 1:3:6 (40mm graded stone aggregate) in Concrete Bed to Drain Pipes of 110mm bore (dia) including Packing Under and Haunching against the Sides of Pipes after they are laid and tested; complete all as specified and as directed. NOTE : Earth Works will be Measured and Paid for separately under appropriate Items.

M&L Cement Concrete 1:3:6 (40mm graded stone aggregate) in Concrete Bed to Drain Pipes of 160mm bore (dia) including Packing Under and Haunching against the Sides of Pipes after they are laid and tested; complete all as specified and as directed. NOTE : Earth Works will be Measured and Paid for separately under appropriate Items.

M&L Cutting into existing Manholes for Connecting PVC (SWR) Pipe 110mm bore (dia), Making Good to Pipe and Rendering, Cutting out existing Benching for and forming Branch Channel (½ Round or ¾ Section) in Cement Concrete 1:2:4 (20mm graded stone aggregate), Smooth Finished and Reforming Benching as required, complete all as specified and as directed.

M&L Cutting into existing Manholes for Connecting PVC (SWR) Pipe 160mm bore (dia), Making Good to Pipe and Rendering, Cutting out existing Benching for and forming Branch Channel (½ Round or ¾ Section) in Cement Concrete 1:2:4 (20mm graded stone aggregate), Smooth Finished and Reforming Benching as required, complete all as specified and as directed.

E/M SERVICES/WORKS

M&L Taking down carefully Copper/Aluminium Point Wiring (Light, Fan, Socket or Power) complete from in any Position including Fixture and Fittings such as Switches, Ceiling Roses, Pendants, Regulators, Sockets but excluding Light Fittings of any description, Making Good Disturbed Surfaces of Walls/ Ceillings, etc. in Cement Mortar 1:3 including providing Surface Treatment (White/ Colour Washing, Distempering, Painting, etc.) wherever required to match the Existing Finishes, complete all as specified and as directed.

M&L Taking down/ out carefully MCB of any descriptions, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded single core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE LIGHT/ FAN/ BELL POINT controlled by One 1-way Switch 6 Amp, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded single core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire for ONE 3/5 PIN SOCKET 6 AMP POINT on SAME BOARD, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded single core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE 3/5 PIN SOCKET OUTLET 6 AMP POINT on INDEPENDENT BOARD, complete all as specified and as directed.

M&L Point Wiring with 2.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded single core Copper Conductor Cable with 2.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE 3/5 PIN SOCKET OUTLET 6/16 AMP POINT on INDEPENDENT BOARD, complete all as specified and as directed.

M&L Sub-main Wiring with 2-Runs of 2.5 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable and 1-Run of 2.5 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuty Conductor drawn through and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc., complete all as specified and as directed. NOTE :- (a) Cost of 3-Runs of Cables & 1-Run of PVC Casing Capping shall deem to be include in the Quoted Unit Rate and the same will be Mesured as ONE UNIT. (b) Sub-main Wiring will be measured PVC Conduit only. Wires required for looping, etc. as ordered will deem to be include in the Quoted Unit Rate.

S&F PVC Rectangular Block/ Board Closed Recessed of size 350x300x50mm deep with 3.0mm thick Plastic Laminated Sheet Cover including Taking down/ out unserviceable Block/ Board of any description, complete all as specified and as directed.

S&F Switch Piano 6 Amp, Single Pole, Flush type, 1-way, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Socket Outlet 6 Amp, 5 Pin, Flush type, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Switch Socket Combination 6/16 Amp, (3 & 3 Pin), 2-in-1, Multipurpose, Flush type, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Lamp/ Angle Holder PVC/ Polycarbonate type with Back Plate suitable for Batten Fitting and connecting up, complete all as specified and as directed.

S&F Ceiling Rose 65x50mm, 3 Terminals, Surface Bakelite suitable for 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Ceiling Fan Regulator, Electronic, Stepped type, 230 Volt AC including necessary Connection and connecting up, complete all as specified and as directed.

S&F Wall mounted LED Tube Light Fitting 1x20 Watt with 20 Watt LED Tube, Aluminium Housing and Integrated Electronic Driver and Connecting up with and including Twin Flexible Copper Wire of size 40/0.0076 of suitable length, complete all as specified and as directed. MAKE : BAJAJ/ CG/ C&S/ HAVELLS/ HPL/ PHILIPS (as approved by GE)

S&F LED Tube Light Fitting 1x20 Watt, T-08 type with 20 Watt LED Batten/ Tube and Connecting up with and including Twin Flexible Copper Wire of size 40/0.0076 of suitable length with 2 No. PVC Box for fixing of Tube Light Fitting including Taking down/ out unserviceable Light Fittings of any descriptions, complete all as specified and as directed. MAKE : HAVELLS, Cat No. LHEXBXPNIN1W020 or equivalent Model in Make : BAJAJ/ CG/ C&S/ HPL/ PHILIPS

M&L Lowering/ Taking down Ceiling Fan of any Make/ Sweep from any Height after disconnecting Electric Connection and Removing to MES Store Yard (at ALONG) for Opening & Checking in presence of JE-in-Charge to ascertain the quantum of Defects and Repair Work involves, complete all as specified and as directed. NOTE :- (a) Any Minor Repairs involved to make the Fan Functional even if not notified by the JE-in-Charge, the same shall be carried out by the Contractor without any Extra Cost to the Department. (b) If Rewinding Work is required, the same will be Measured and Paid separately under relevant Item.

M&L Transporting Ceiling Fan 1200mm Sweep of any Make from MES Store Yard (at ALONG) to nearest Workshop, Removing burnt Winding, Cleaning Slot, Rewinding Fan Motor with Super Enamalled Copper Wire of suitable Gauge and Weight not less than 350 Gram, providing necessary Insulation Materials, Varnishing, Heating, Reassembling & Testing for Smooth Functioning after Rewinding, Transporting Fan to Site of Work after Rewinding, complete all as specified and as directed. and as directed. NOTE : Cost of all Materals & Labour required for Rewinding of Ceiling Fan for Smooth Function will deemed to be included in the Quoted UNIT RATE.

M&L Preparing Old Painted Surfaces of Fan including Cleaning, Washing, Rubbing and Filling Cavities with Filler, applying One Coat of Synthetic Enamelled Paint (as approved) with Spray Painting Machine and Writing MES No. with Black Paint, complete all as specified and as directed.

M&L Mild Steel Flat Iron 40x3mm as Fan Hook, cut to length, bent to Shape, drilling holes as required, etc. for hold GI Pipe hanging Fan, conforming to Fe-290 Gde-E-165 including Mild Steel Bolts, Nuts, Washers, etc., complete all as specified and as as directed.

Supply & Hanging Ceiling Fan 1200mm Sweep, 75 Watt, 220 Volt, 50 Hz, with Double Ball Bearing System and High Speed Performance having Long Lasting Paint Finish and providing Electric Connection with and including suitable size Copper Conductor Cable from Ceiling Rose to Ceiling Fan, complete all as specified and as directed.

M&L Hanging only Ceiling Fan and connecting with and including suitable size Copper Conductor Cable from Ceiling Rose to Ceiling Fan, complete all as specified and as directed.

S&F Exhaust Fan 230mm Sweep, Steel body with Louver Shutter, 230 Volt AC Supply with Fixing Arrangement using Fastener and providing Electrical Connections from Ceiling Rose to Exhaust Fan with and including PVC Flexible Cable of size 23/0.0076, 3 Core, complete all as specified and as directed.

M&L Cutting Holes in Pre-cast Concrete Block Masonary Walls of suitable size for fixing Exhaust Fan and Making Good to Dismantled Portion with Cement Concrete 1:2:4 (20mm graded stone aggregate) or Cement Mortar 1:3 (as required), complete all as specified and as directed.

S&F MCB Single Pole 6 Amp to 32 Amp, 'C' Series, 50 Hz, 10 kA, 240 Volt and Connecting up, complete all as specified and as directed.

S&F MCB Single Pole & Neutral 6 Amp to 32 Amp, 'C' Series, 50 Hz, 10 kA, 240 Volt and Connecting up, complete all as specified and as directed.

S&F MCB Single Pole & Neutral 40 Amp, 'C' Series, 50 Hz, 10 kA, 240 Volt and Connecting up, complete all as specified and as directed.

S&F Sheet Metal Enclosure, Distribution Board 4-way, Single Door 240 Volts AC, SPN, Painted with Epoxy Based Powder coated Painting suitable for mounting MCB DP/ SPN as Incomer and MCB SP as Out-goings with 200 Amps rated Bus-bar, Neutral Bar, Earth Bar Connecting Cable Links with Top and Bottom Removable Gland Plate, with IP 43 Protection and Connecting up, complete all as specified and as directed. MAKE : HAVELLS/ LEGRAND/ L&T/ SCHNEIDER (as approved by GE)

S&F Sheet Metal Enclosure, Distribution Board 4-way, Double Doors 240 Volts AC, SPN, Painted with Epoxy Based Powder coated Painting suitable for mounting MCB DP/ SPN as Incomer and MCB SP as Out-goings with 200 Amps rated Bus-bar, Neutral Bar, Earth Bar Connecting Cable Links with Top and Bottom Removable Gland Plate, with IP 43 Protection and Connecting up, complete all as specified and as directed. MAKE : HAVELLS/ LEGRAND/ L&T/ SCHNEIDER (as approved by GE)

S&F Sheet Metal Enclosure, Distribution Board 6-way, Single Door 240 Volts AC, SPN, Painted with Epoxy Based Powder coated Painting suitable for mounting MCB DP/ SPN as Incomer and MCB SP as Out-goings with 200 Amps rated Bus-bar, Neutral Bar, Earth Bar Connecting Cable Links with Top and Bottom Removable Gland Plate, with IP 43 Protection and Connecting up including Taking down/out unserviceable Sheet Metal Enclosure of any description, complete all as specified and as directed. MAKE : HAVELLS, Cat No. DHDPSHOSRW08 or equivalent in LEGRAND/ L&T/ SCHNEIDER (as approved by GE)

Supply & Laying or Fixing or Passing through Pipe, 1100 Volts grade, Heavy duty Cable with PVC insulated Aluminium Stranded Conductor, served with an inner Sheathing of PVC Tape Armoured with Galvanised Steel Wire or Tape and Overall PVC Sheathed 4.0 Sqmm Nominal Cross section in Service Connections, complete all as specified and as directed.

Supply & Laying or Passing through Pipe 1100 Volt grade heavy duty, Cross-sectional area 6.0 Sqmm, 2 Core, Flat or Circular Cable with PVC insulated Aluminium Conductor served with an inner sheathing of PVC Tape armoured with Galvanised Steel Wire or Tape and Overall PVC sheathed in Service Connection suspended by insulating Hangers not more than 1.0 Metre apart including 4.0mm Suspension Wire, complete all as specified and as directed.

M&L Earthing with Galvanised Earth Plate Electrode 600x600x6.0mm thick, buried directly in Ground vertically to a depth not less than 2.25 Metre below Ground Level with Top Edge of Earth Plate at depth not less than 1.50 Metre below normal Ground Level, connected to Galvanised Earth Lead Wire 4.0mm dia by means of Bolts, Nuts, Check, Nuts and Washers of Galvanised Iron or Steel and Earth Wire protected with and including GI Pipe 15mm bore (dia) Light grade, connected to Test Point upto 7.50 Metre away from Earth Electrode situated, Earth Plate surrounded by a packed thickness of Char Coal or Coke Dust mixed with Common Salt in alternate layers of not exc.150mm thick, PCC Pit in Cement Concrete 1:3:6 (20mm graded stone aggregate) and Pre-cast RCC Cover Slab of size 350x350x50mm in Cement Concrete 1:2:4 (20mm graded stone aggregate), reinforced with 10mm dia TMT Bars @ 100mm Centre to Centre in both ways, GI Wire Mesh, PGI Funnel with GI Watering Pipe 20mm bore (dia) Medium grade including necessary Excavation in Soft/ Loose Soil, Returning, Filling in and Removal of surplus Spoil upto a distance of 50.00 Metre and all as shown in Electrical Plate No. 3 of MES Schedule Part-I and Testing including Taking down/out unserviceable Earthing of any description, complete all as specified and as directed.

Excavating in Trenches, not exc. 1.50 Metre Wide and not exc. 1.50 Metre in Depth for Taking out/ up and/or laying of Water Pipe Line, Cable Line, etc., Forming surfaces to required Foundation/ Gradient and getting out in Soft/Loose Soil, complete all as specified and as directed.

Returning, Filling in including Spreading, Levelling, Watering, Well Ramming in Layers not exc. 25 Cm, Providing Heaps with Surplus Soil along the Route of the Water Pipe Line, Cable Line, etc., in Soft/Loose Soil, complete all as specified and as directed.

Supply & Laying LT Under Ground Cable 1100 Volt grade, XLPE insulated, PVC sheathed heavy duty, armoured with multi-stranded Aluminium Conductor all as per IS:7098 (Part-I)-1998, Cross-sectional Area 10 Sqmm, 2 Core, laid in Trenches, Ducts or through Pipes or fixing to Poles, etc. including Taking out unserviceable Cable of any description, complete all as specified and as directed. NOTE : Necessary Earth Works, Sand Cushioning, Cable Protection Cover & Pipe, etc. (as ordered) will be Measured and Paid separately under relevent Items.

Supply & Laying HDPE Double Wall Corrugated (DWC) High Density Polythene Pipes of Outer Dia 40mm & Inner Dia 32mm, having corrugation on the Outer Wall and Plain surface on the Inner Wall, conforming to IS:14930 (Part I & II), cut to length as per Site Requirements for protection of UG Cable/ in PCC including Cutting Floors, etc. and Making Good the Same with Original Specification to match the Existing Adjoining Surfaces, etc., complete all as specified and as directed. NOTE : Quoted UNIT RATE is inclussive of all Accessories for fixing of DWC Pipe with Walls, Roofs, Cable Tray, etc.as Site requirments.

Sunwin Energy and Infra Pvt Ltd