Furnishing of New Khadi Grama Soubhagya, Kaloor in Ernakulam

Amount

APPENDIX-A

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar ( D S R 2016 , 15.7.4 )

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in Charge Nominal concrete 1:4:8 or leaner mix (i/c equivalent design Mix ) ( D S R 2016 , 15.2.2. )

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. ( D S R 2018 , - 15.3 )

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. ( D S R 2016, 15.56 )

Dismantling doors, windows and clerestory windows (steel or wood) shutter including Chowkhats, architrave, hold fasts etc complete and stacking within 50 metres lead Of area 3 sq. metres and below ( D S R 15.12.1. )

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm ( D S R 2016 , 15.23.1 )

Dismantling Aaluminium / Gypsum Partitions, doors, windows, Fixed glazing and False ceiling including disposal of unserviceable surplus material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge. ( D S R 15.57 )

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). ( D S R 4.1.5 )

Solid masonry using pre cast solid blocks (factory made) of size 30x20x15cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level with thickness 15cm in : CM 1:6 ( 1 cement : 6 coarse sand) etc complete ( Observed Data Buildings 50.6.2.2. )

12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand) ( D S R 13.4.1. )

12 mm cement plaster finished with a floating coat of neat cement of mix : 1:3 (1 cement: 3 fine sand) D S R 13.7.1 )

Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. meters and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50metres lead : With cement mortar 1:4 (1 cement : 4 fine sand). ( D S R 14.1.1. )

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. ( D S R 10.2. )

Steel work in built up tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes ( D S R 10.16.1 )

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc.( D S R 9.48.2 )

Providing and fixing plain multipurpose cement board(Hight pressure steam cured) with suitable screws for cement particle board in ceiling , partition etc. complete (frame work to be paid seperatately). 8 MM thick Cement fiber board as per IS: 14862 ( D S R 12.26.1 )

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 300x16 mm ( D S R 9.96.1. )

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 250x10 mm ( D S R 9.97.2. )

Providing and fixing Aluminium Handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm ( D S R 9.100.1. )

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08%and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm ( D S R 2016, 11.41 .2 )

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. Size of Tile 600x600 mm ( D S R 11.48.2. )

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade ( D S R 8.2.2.2. ) Area of slab over 0.50 sqm

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with: Gypusm Plaster Board of size 1200 x 2400 x 12.5 mm, with all 4 side tapered ( D S R 2016 12.45.1. )

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: ( D S R 25.7. )

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer ( D S R 13.43.1 )

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade: Two or more coats on new work. ( D S R 13.60.1. )

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work. ( D S R 13.61.1 . )

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete ( D S R 2018 13.91 )

Providing and applying Plaster of paris Putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. ( D S R 13.26 )

Finishing walls with Acrylic Smooth exterior paint of required shade: Old work (Two or more coats applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface ( D S R 13.111.1 )

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade : One or more coats on old work ( 2018 D S R 13.98.1 )

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : One or more coats on old work. ( 2018 D S R, 13.99.1 )

Melamine polishing on wood work (one or more coat). ( 2018 D S R , 13.114 )

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work ( D S R 2018 , 13.52.1 )

Providing and fixing Aluminium work for Doors, Windows, Ventilators and Partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion - Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron) ( D S R 21.1.1.3 )

For Shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron) ( D S R 21.1.2.3 )

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 8 mm thickness ( D S R 21.3.3. )

Providing and fixing double scaffolding system (cup lock type) on the exterior side, upto seven story hight made with 40 mm dia. M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staricase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after. The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required location with essential safety features for the workmen etc. complete as per directions and approval of Engineer- in Charge. The elevational area of the scaffolding shall be measured for payment purpose. The payment will be made once irrespective of duration of scaffolding. Note:- This item to be used for maintenance work judicially, necessary deduction for scaffolding in the existing item to be done .( D S R 14.72 )

Providing and fixing Double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. With stainless steel cover plate minimum 1.25 mm thickness ( D S R 21.4.1. )

Supplying and Fixing Good Quality Stainless Steel Door Handle For Glass Door of size 45 cm With all necessary screws, nut bolts etc complete as approved by the Engineer in Charge. ( Observed Data od 46046/2021-2022 )

Providing and fixing PVC, pipes fittings including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 32 mm dia 6 Kgf/cm2 - internal work- Exposed on wall ( Observed Data Buildings 50.18.7.4.2. )

Engaging Labour For Cleaning works / Repair Works Beldar ( D S R 0115 )

Engaging Labour For Maintenance works / Repair Works Fitter / Plumber Gr I ( D S R 0116 )

Engaging Labour For Maintenance works / Repair Works Carpenter

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, For all leads including all lifts involved. ( D S R 2018 , 15.60 )

Supplying fabricating and fixing in position Sales counter with Granite / Glass top of 80 CM TOP WIDTH AND HEIGHT 80 CM ( AV ) ,made with frame work of 16 mm BWR ( IS 303 GRADE ) Plywood including covering the front and SIde , Providing inside Racks using 16 mm BWR ( IS 303 GRADE ) Ply wood, Covering all the expsed surface with suitabe thickness decorative Laminated sheet of approved brand with suitable adhesive ( HEATEX or equvqlent ), the inside of the counter being painted with synthetic enamel paint 2 coat over one coat of wood primer and putty leveling, filling etc. Providing 12 mm thic edge polished glass/ 18 mm thick egde polished Granite for the Top area with necessary glass caps or adhesives, providing 8 mm thick edge polished glass for the front vertical area with suitable D brackets , Finishing including polishing all the exposed area complete as per the approved drawings and direction of the Engineer in charge.. ( OBSEVED DATA od3_P100001/2019-2020 )

Supplying fabricating and fixing in position Sales counter with Granite / Glass top of 60 CM TOP WIDTH AND HEIGHT 80 CM ( AV ) ,made with frame work of 16 mm BWR ( IS 303 GRADE ) Plywood including covering the front and SIde , Providing inside Racks using 16 mm BWR ( IS 303 GRADE ) Ply wood, Covering all the exposed surface using suitable thickness decorative Laminated sheet with Texture Finish of approved brand with suitable adhesive ( HEATEX or equvqlent ), the inside of the counter being painted with synthetic enamel paint 2 coat over one coat of wood primer and putty leveling, filling etc. Providing 12 mm thic edge polished glass/ 18 mm thick egde polished Granite for the Top area with necessary glass caps or adhesives, providing 8 mm thick edge polished glass for the front vertical area with suitable D brackets , Finishing including polishing all the exposed area complete as per the approved drawings and direction of the Engineer in charge.. ( OBSEVED DATA od3_P100001/2019-2020 )

Supplying fabricating and erecting CASH cum PACKING Counter of 1 M height (av) with width and length 70 to 90 cm and 2.30 m respectively by using Frame work of 16 mm thick B W R ( IS 303 GRADE ) plywood including covering Front and Side , Providing inside partition, drayers, key board drayer, cupboards etc using 16 mm BWR ( IS 303 GRADE ) Plywood, Covering all the exposed surface with Suitable thickness Decorative laminated sheets with Texture Finish of approved brand and quality with suitable adhesive ( HEATEX or equvqlent ), Providing and fixing on Top portion with 12 mm thick edge polished plain glass with suItable 40mm x 12 mm spacers and in the secound hight counter portion providing Edge Polished granite or marble (jet black or galaxy) ,Including providing and fixing cupboard drawers with locking arrangement foot rest, Space for UPS, CPU etc. and all the inside area of counter being painted with two coats of synthetic enamel paint over a coat of wood primer after applying putty levelling filling etc. finishing all the exposed area with Polish etc complete all as per the approved drawings and direction of the Engineer in charge.

Supplying and fixing Modiguard or Equivalent Brand glass Mirror over Frame work of 16 mm BWR Quality IS 303 Grade Play wood frame and covering the rear side with 12 MM BWR plywood and finishing all the exposed surface with Suitable Thickness Decorative Laminated Sheets With Texture Finish of approved brand and shade , Fixing on Wall etc. complete as per the direction of Engineer in charge.

Providing and Fixing plywood Back ground panel made out of FRAME work using 16 mm BWR QUALITY ( IS 303 grade ) plywood at suitable spacing both horizontally and vertically, including making hole in the concrete/ masonry wall, with necessary SS hold fasts or SS screws of necessary size. Then Commercial plywood 12 mm thick B W R grade ( IS 303 Grade ) of approved make is fixed to the Exposed side of the frame work with screws of necessary size , all the exposed surface covered by suitable thickness Decorative Laminated Sheets with suitable adhesive ( Heatex or Equivalent ) including sealing all the joints and holes all as per the approved drawings and Direction of the Engineer in Charge .

Supplying fabricating and erecting in position GODOWN RACK of 1.20m x 2.44 m x 0.40 m by using 12mm / 16 mm / 18 mm thick commercial ply wood board conforming to IS : 303 BWR Grade , 16 mm thick 3 nos for vertical members, 18 mm thick 5 racks horizontal and 12 mm thick for back covring , all Exposed surface should be painted with 2 coat of Synthetic Enamel over a coat of primer etc. complete as per the approved drawings and direction of the Engineer in charge.

Providing and fixing WOODEN Display shelf for Ornamental Items ( RACK BEHIND CASH COUNTER ) with frame work using 16 MM BWR ( IS 303 GRADE ) PLY WOOD , providing 12 mm thick ( IS 303 GRADE ) BWR ply wood on rear side, covering the frame work with 16 mm ( IS 303 GRADE ) BWR ply wood, covering the exposed surface with suitable thickness Decorative laminated sheets with addhessive of approved brand ( Heatex or Equivalent ) , providing 12 mm thick edge mechine polished glass for racks with necessary supports in the upper portion, providing 16 mm thick BWR ( IS 303 GRADE ) PLY WOOD SHUTTERS INCLUDING NECESSARY HINGES , HANDLES ETC for racks in the lower area, applying 1 coat of wood primer , putty finishing , synthetic enamel 2 coat all as per the drawing and Direction of the Engineer in Charge .

Providing and fixing Wooden Display shelf with frame work using 16 mm thick IS 303 GRADE BWR Plywood , covering the frame work with 16 mm thick IS 303 Grade BWR Quality ply wood, covering all the exposed surface with suitable thickness decorative laminated sheet with Texture Finish using good quality addhessive ( Heatex or Equivalent ) providing 12 mm thick edge mechine polished glass for racks with necessary supports, all as per the drawing and Direction of the Engineer .

Providing M S DISPLAY RACKS in Steel work in built up tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding grinding and bolted with special shaped washers etc. complete. Hot finished welded type tubes ( D S R 10.16.1 )

Providing and fixing 8.00 mm thick Float Glass panes as racks in MS Display Racks , Display Stand including grinding and polishing the exposed edges etc complete as per the architectural drawings and the directions of Engineer-in-charge

Providing and fixing TEAK wood frame work consisting of battens 100 x 50 mm For Fixed Glasing and Door , fixed with rawl plug and drilling necessary holes for rawl plug etc. including Polishing complete. For Fixed Glased Partitions and Doors

Providing and fixing Glazing in wooden frames using 12 mm TOUGHNED Glass of approved brand in Fixed partitions and glazed shutters for doors, (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured).

Providing and fixing Glazing in Aluminium Partitions door, window and ventilator shutters etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item): With TOUGHNED GLASS panes of 12 mm thickness

Providing and fixing KHADI SHELF Horizontal Spacing 90 cm and vertical Spacing 30 cm ( except bottom shelf of 60 cm spacing) with stainless steel ( Grade 202 ) Hollow tubes, channels, plates etc., and 8 mm Glass , including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the Shelf to the Wall / Columns with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., Providing 8 mm Glass of of required size, including polishing the exposed edges , all as per the Drawing and approval of the Engineer-in-charge,

Providing and fixing DISPLAY SHELF , Horizontal Spacing 90 cm and vertical Spacing 45 cm with 40 MM AND 25 MM M S Hollow tubes, channels, plates etc., and 8 mm Glass , including welding, grinding, providing 2 coats of primer and 2 coat of Epoxy Paint ( SPRAY fiNISH ) etc complete, including fixing the Shelf to the Wall / Columns with necessary accessories & stainless steel dash fasteners , Providing 8 mm Glass of of required size, including polishing the exposed edges , all as per the Drawing and approval of the Engineer-in-charge,

Providing and Fixing plywood SEATING SHELF with drawyers of size 1.80 x 0.40 x 0.30 m made out of FRAME work using 16 mm BWR QUALITY ( IS 303 grade ) plywood at suitable spacing both horizontally and vertically, including covering all the exposed surface by suitable thickness Decorative Laminated Sheets with Texture Finish with suitable adhesive ( Heatex or Equivalent ) including providing seating on top with Granite of approved quality all as per the approved drawings and Direction of the Engineer in Charge .

Providing Texture Work in Wall , Ceiling with approved brand and Design as approved by the Engineer in charge.

Providing and Fixing WALL PAPER OF APPROVED BRAND AND DESIGN as approved by the Engineer in Charge.

Providing and Fixing plywood RAISED PLATFORM ( 12 CM ) made out of FRAME work using 16 mm BWR QUALITY ( IS 303 grade ) plywood at 45 CM C/C spacing both ways and fixing the same to floor with necessary SS hold fasts or SS screws of necessary size. Then Commercial plywood 18 mm thick B W R grade ( IS 303 Grade ) of approved make is fixed to cover the frame work with screws of necessary size including sealing all the joints and holes all as per the approved drawings and Direction of the Engineer in Charge .

Providing and Fixing CARPET FLOORING by with good quality and texture carpet including cost of all materials and labour as per approved Design

Providing Name Board by Vinyle Sticker Work on Existing ACP PANNEL WORK as per approved Design

APPENDIX-B-ELECTRICAL

Engaging Labour for Maintenance work Electrician

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. GROUP B ( D S R ELECTRICAL 1.10.2 )

Wiring for Twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with 2 Way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. ( D S R ELECTRICAL 2016 1.11 )

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings). ( D S R ELECTRICAL 1.31 )

SUPPLY AND FIXING 1200 MM BATTEN LED LIGHT 20 WATTS WITH ALL NECESSARY FITTINGS ( od15443/2021_2022 )

Charges for cutting holes suitable for accommodating exhaust fans up to 305mm sweep including plastering colour washing etc. as required. ( OD ELECTRICAL 90.4.8 )

SUPPLY AND FIXING 250 MM EXHAUST FAN WITH NECESSARY FITTINGS ( od15434/2021_2022 )

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required. 20 MM ( D S R ELECTRICAL 1.21.1 )

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required. 25 MM ( D S R ELECTRICAL 1.21.2 )

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required. 3 X 1.5 sq.mm ( D S R ELECTRICAL 1.17.3 )

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required. 3 x 2.5 sq. mm ( D S R ELECTRICAL 1.17.12 )

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required. 3 x 4 sq. mm ( D S R ELECTRICAL 1.17.21 )

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required. 4 x 6 sq. mm ( D S R ELECTRICAL 1.17.31 )

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. 1 or 2 Module (75mmX75mm) ( D S R ELECTRICAL 1.27.1 )

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. 3 Module (100mmX75mm) ( D S R ELECTRICAL 1.27.2 )

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.12 Module (200mmX150mm) ( D S R ELECTRICAL 1.27.6 )

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 amps switch ( D S R ELECTRICAL 1.24.1 )

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Two Way 5/6 amps switch ( D S R ELECTRICAL 1.24.2 )

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 15/16 amp switch ( D S R ELECTRICAL 1.24.3 )

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 3 pin 5/6 amp socket outlet ( D S R ELECTRICAL 1.24.4 )

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 6 pin 15/16 amp socket outlet ( D S R ELECTRICAL 1.24.5 )

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. ( D S R ELECTRICAL 1.26 )

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/ISOLATOR ) 6 WAY 4 + 18 DOUBLE DOOR ( D S R 2.4.2 )

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar,, interconnections, powder painted including earthing etc. as required. (But without MCBIRCCB/Isolator 2 + 8 Way Double Door ( DSR 2.3.7. )

Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. ( 40 Amps ) ( D S R 2.12. 1 )

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single Pole ( D S R ELECTRICAL 2.10.1 )

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required ( D S R ELECTRICAL 2.11 )

Supplying and fixing following rating, Four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 Amps ( D S R ELECTRICAL 2.13.2 )

Supplying and fixing following rating, Four pole, ( Three phase and neutral), 415 volts, Residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 Amps ( D S R ELECTRICAL 2.15.3. )

Providing and fixing Flexi LED Strip for Cove Lighting 12 W with suitable Drive of aproved brand ( Wipro / Bajaj / Philips Or Eqivalent. )

Supply, conveyance installation testing and commissioning of Sleek Compact Recess Mounting LED Slim Panel light fitting 3W/4W , square or round, Cool or Warm , size 75 mm ( or nearest available ) with light Weight Body, energy efficient drive ,complete with all accessories , fixing directly on ceiling including giving connection with required length of 16/0.20 mm 3 core round copper conductor flex wire conforming to relevant ISS or extending the original wiring etc. as required.

Supply, conveyance installation testing and commissioning of Sleek Compact Recess Mounting LED Slim Panel light fitting 6 W , square or round, Cool or Warm , size 105 mm ( or nearest available ) with light Weight Body, energy efficient drive ,complete with all accessories , fixing directly on ceiling including giving connection with required length of 16/0.20 mm 3 core round copper conductor flex wire conforming to relevant ISS or extending the original wiring etc. as required.

Supply, conveyance installation testing and commissioning of Sleek Compact Recess Mounting LED Slim Panel light fitting 12 W , square or round, Cool or Warm , size 155 mm ( or nearest available size ) with light Weight Body, energy efficient drive ,complete with all accessories , fixing directly on ceiling including giving connection with required length of 16/0.20 mm 3 core round copper conductor flex wire conforming to relevant ISS or extending the original wiring etc. as required.

Supply, conveyance installation testing and commissioning of Sleek Compact Recess Mounting LED Slim Panel light fitting 18 W , square or round, Cool or Warm , size 205 mm ( or nearest available size ) with light Weight Body, energy efficient drive ,complete with all accessories , fixing directly on ceiling including giving connection with required length of 16/0.20 mm 3 core round copper conductor flex wire conforming to relevant ISS or extending the original wiring etc. as required.

Supply , conveyance, installation, testing and commissioning Wall mounting fan of 400 mm Sweep with Oscillation system and Pull Cord, using mounting brackets supplied along with the fan and giving connection with existing wire.

Supplying installation testing and commissioning of 2 Ton Split Air conditioner ( INVERTOR AC ,FULL COPPER ) with remote control of make Voltas / Blue Star / L.G /.Carrier or equivalent make with 1 unit of Voltage stabilizer ( V Guard VG 500 Stabiliser or Equivalent approved make suitable for 2 Ton invertor AC ) , providing angle iron / Wall Munting Bracket support to the out door and indoor unit , copper tube, cable etc complete. including cutting and making good of the masonry wall / concrete as directed by the Engineer in Charge .

Supplying , installing , testing and commisioning CC TV System with CP Plus –2.40 MP AHD IR D/N Dome Camera with 3.6 mm Lens, IR Distance 20 meter. 8 Nos , CP Plus 8 channel . Standalone DVR with TCP / IP / LAN / Eithernet, remote, channeling, playback, motion, mobile imaging, with out HDD. 1 unit, A/C D/C Power supply 5 Amps SMPS -1 , RCA/BNC Cable Connecters - 12 nos, 2 TB HDD -1 , 1 18.5” Monitor , with Cabling with 3+1 control cable and accessories as required

Suresh