SPECIAL REPAIR TO BLDG NO T 10 AT NEPAL LINE AND PROVN OF CHAIN LINK FENCING IN JCOs OR MD ACCN IN SARAVATRA NAGAR UNDER AGE BR WEST GE DEHU ROAD

Amount

Dismentling single layer Manglore pattern or similar tiles in roofing

Dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings all as specified and directed.

Dismentling unframed timber scantling 40 Sq.cm and over in section, in any position complete all as specified and directed.

Dismantling of wrought iron or mild steel work any description and fixed in any position complete all as specified and directed.

M&L rolled sections as in main and cross beams, hip rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed witjh angle cleats or other connecting plates Fe 410 W (gde E 250 ) quality A including a shop coat of zink chromate primer complete all as specified and as directed.

S & F 0.5 mm thick pre-painted/coloured galvalume Al zinc coating GI based profile sheet of any colour having tensile strength of 550 Mpa as in roofing fixing with coach screw all as per manufactures instructions fixed on roof with all fittings and accessories.

Ditto as per item No- 06 above but as in ridge, valley gutters etc complete all as specified and directed.

M & L for MS work as in wind tie or any other work incl cutting, drilling holes etc.

Dismentling wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs/ blankets any thickness including cover fillets and S & F 12mm thick Gypsum board for ceiling, insulation and accoustic purpose 60x60cm in size fixed with screws with staples incl aluminium snap grid frame work 605x605 mm in flat/slopting ceiling with aluminium anodised grid work 35.60x23.60x1.60mm main Tee 23.60x23.60x1.60mm cross section and 26x26x1.60mm angle including 3mm dia GI wire suspender of suitable length aluminium cleats etc complete all as specified and directed.

Dismentling wall & floor tiles, incl cement mortar bedding (but not backing)

M & L non skid coloured ceremic tles 7 to 8 mm thick area of each tiles exceeding 0.06 sq.m but not exc. 0.11 sq.m , in floors, etc.set and jointed in cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete and as specified and directed.

M&L for vitrified coloured tiles 10mm th (square/rectangular) polished area of each tile 0.36 sqm but n exc 0.42 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of tiles over 15 mm th screed bed in CM 1:6 complete

Ditto as per item No 12 above but in skirting over 10 mm th backing coat in CM 1:4 complete all as specified and directed.

M&L for glazed coloured ceramic tiles 450 mm x350x 7 mm thick as in vertical surfces set & jointed in neat cement slurry & pointed in coloured cement to match the tiles incl backing coat 10mm thick in CM 1:4 all as specified direced.

Dismantling of stone slabs and tiles of any description or thickness in floors aprons laid and bedded and jointed in cement mortar complete all as specified and as directed.

M&L for Marble work green marble 18 to 20 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in CM (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with green marble shade complete all as specified.

Demolition of brick work or stone boulders masonary built in cement mortar including all arches, pillars etc all as speicified and directed.

M&L for brick work with sub class 'B' bricks straight or curved on plain exc. 6m mean radius built in CM 1:6 complete all as specified and directed by Engr-in Charge.

M & L for Complete removal of existing treatment including washing, rubbing down and stopping of distempered surfaces and applying two coats of oil bound distemper complete over a coat of primer and 3 mm thick wall care putty on wall surface complete all as specified and directed.

M & L for Complete removal of existing treatment including washing, rubbing over old plastered down surfaces and applying two coats of cement base Paint over a coat of primer on wall surface of wall complete all as specified and directed.

Taking down cement plaster of any description of brick or stone wall etc incl racking out joints and hacking for key, scrubbing down with water etc complete

M&L for rendering 10 mm thick in CM 1:6 on fair faces of brick walls finished even and smooth w/o using extra cement and all as specified and directed.

M&L for rendering 15 mm thick in CM 1:4 on fair faces of brick work or conrete surfaces finishing the surfaces even and smooth without using extra cement and all as specified and directed.

M&L for preparation of new plastered surfaces & applying two coats of oil bound distemper complete over a coat of primer on wall surface complete all as specified and directed.

M&L for preparing new plastered surfaces & applying two coats of cement base Paint over a coat of primer on wall surface of wall complete all as specified and directed.

Taking down chowkhats or frame with shutter with frame (w/o taking off shutter from the frame) of area exc 1.5 but not exc 4.00 Sq.m (incl steel windows)

–Ditto- as item No 26 above but n.exc. 1.50 sqm each including old window

S&F for pressed steel door frames with one or more rebates incl necessary fixing lugs, hinges, lock strike plates of size 125 X 60mm complete and all as specified and directed.

S&F for pressed steel door frames with one or more rebates incl necessary fixing lugs, hinges, lock strike plates of size 105 X 60mm complete and all as specified and directed.

M&L for cement concrete (1:3:6) type B0 (using 12.5 mm graded stone agg) as in back filling door frames complete and all as specified and directed.

S&F 30 mm thick flush shutter solid core construction with block board corre & plywood face pannels commercial type on both sides complete and all as specified and directed.

S & F 35mm thick factory made glazed & skeleton shutter of 2nd class hard wood open rebated and prepared to receive gauge (divided into squares with sash bars) edges of framing plain chamfered or rounded, fitted without & fitted beads for securing glass etc, sizes of members of shutters as specified in SSR Pt-I Sec-8 clause 8.23 (a) and fitted to chowkhats complete all as specified.

M & L for preparation of new wooden surfaces exc. 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10 cm width or girth & applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L One coat of synthetic enamel paint on old painted steel surfaces over 10 cm width or girth incl prepration of surfaces complete all as specified and directed

S&F aluminium powder coated window sliding type (3 track) with frame size100x35x1.2mm and shutter 39.40x17.70x1.2mm with two glass shutter & one mesh shutter incl necessary jointing cleats glazing clips, rubber packing,and locking arrangement powder coated aluminium snap beading screws including 4mm plain float glass & 0.36 mm dia and 1.4 mm width of aperture stainless steel wire mesh, fittings etc complete all as specified.

S & F solid PVC Door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, Suppling and fixing in opening as per specifications and drawing complete and all as specified and directed.

S & F 30mm thick factory made solid PVC moulded door shutter (stiles), consisting of frame out of M.S. tubes for top and bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC ''C'' channel having a PVC sheet strip of 20 mm width struck inside with solcent cement for stiles and plain colour PVC sheet for top rails, Panelling of plain colour PVC sheet to be fitted in the M.S. frame suitable PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together wtih solvent cement, suppling & fixing in the frame at site as per specififcation & drawing.

S & F of 100 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed.

S & F of 200 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed.

S & F of 150 mm long extruded anodised aluminium alloy handle, fabricated type complete all as specified and directed.

S&F 100 mm Stainless steel Butt hinges,medium weight cold rooled fixed with screw or welding complete.

S & F of 300 mm long (Length of bolt) aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolt of extruded sections or cast aluminium alloy complete all as specified and directed.

Disconnecting existing PVC water tanks of capacity 1000 litres, setting aside (or lowering if required) for replacement complete all as specified and as directed.

S & F rotational moulded polyethylene water storage tank of 1000 litre capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified and directed.

S&F in repair PVC ball valves, high pressure with apaxy coated aluminium rod and high density plaster ball screwed for iron pipe 20mm dia complete

Taking down steel tubing galvanised with connections of dia 15 mm complete

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 20cm girth

-do- as above item No 48 but 20mm.

S & F 15 mm dia GI pipes medium grade with all fitting & fixed to wall / floor

-ditto- all as per item No. 50 above but 20mm

S & F in repairs wall mixer telephonic with crutch for hand shower Make : Prayag cat pat No 9370 complete all as specified.

S & F in repairs 15 mm dia bib taps cast copper alloy chromium plated fancy type with crutch or butterfly handles, screwed down for iron pipes or for brass ferrule.

S & F in repairs 15 mm dia stop valves cast copper alloy chromium plated screwed high pressure with crutch or butterfly handles screwed both ends for iron pipe. Etc.

S & F in repairs brass chromium plated shower rose 125 mm size with or without swivel joints incl fixing to steel pipe complete and all as specified and directed.

S/F in repairs Vitreous china wash basin white flat back size 600 x 400x230 mm including , waste pipe and plug and along with 32mm dia CP waste coupling and PVC waste pipe complete all as directed.Make : Somany cat pat No 110408

S&F in repairs 15mm dia pillar taps cast copper alloy with capston head chromium plated screwed down high pressure wlth or without letter "Hot" or "cold" with long screwed shanks and fly nuts

S&F in repairs vitreous china wash down water closet pan (pedestal pattern) of white with 'P' or 'S' trap including connection to drains (or outgoing pipes) and to the flushing pipes, complete all as specified and directed.

S&F Grating round 140 mm size of PTMT (Minimum weight 50gms.)complete all as specified and as directed.

S&F in repairs Toilet Roll Holder with Stainless Steel. Make Jagur Cat Part No ACN-1153S

S&F in repairs 2 in 1 health faucet 1.5 mtr tub with hook . Make Prayag Cat Part No 452

S&F in repairs two way angle cock with flange . Make Prayag Cat Part No 8912 complete all as specified.

S&F in repairs glass corner shelf 200 mm with ABS brackets . Make Prayag Cat Part No BEA-46 complete all as specified.

S&F in repairs towel rack . Make Prayag Cat Part No BA-22 complete all as specified.

S& F in repairs stainless steel Sinks kitchen or laboratory with plugs, washers and wastes; including beding in cement mortar overall size 495mm x 420 mm bowl size 410 mm x 330 mm x 160 mm complete including fixing cantilever brackets and connecting union to waste pipe and coupling ; upto 0.5 sqm each complete all as specified.

S&F in repairs curtain rod 25 mm dia powder coated fancy type complete with side knobs all as specified and directed.

S&F in repairs brackets fancy type powder coated for 25 mm dia drapery rod complete all as directed.

S & F for PVC connection pipe 15mm dia with PTMT nuts of length 450mm

S&F as in repairs PVC low/high level flushing cristern white 10 litre capacity incl PVC inlet pipe with brass check low level full both sides alongwith PVC flush pipe 32mm dia jointed to WC and handle incl bracats fixed in repairs all as directed.

S&F in repair plate rack made of stainless steel 1mm thick kitchen including fixing overall size 915mm x 915mm x 255 mm all as specified and directed.Make Nirali/Silver shine/Prayag

Dismantling / taking down AC waste/vent pipes fixed to walls with all fittings/ accessories 100 mm dia pipes all as specified and directed by Engineer-in-Charge.

S&F PVC (SWR) pipes, single socketed, in any length with rubber ring joints fixed to walls, or laid in trenches bore of pipe 110 mm dia complete all as specified and directed by Engineer-in-Charge.

S&F.110 mm dia PVC (SWR) bends, any radius with access door complete all as specified and directed by Engineer-in-Charge.

S&F 110 mm dia PVC (SWR) vent cowl complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete ( unreinforced) in ground floors and paving n exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

M & L for 75 mm thick Cement concrete 1:4:8 type D-2 (40 mm graded aggregate) as in sub base complete all as specified and as directed.

M & L for Chequered cement concrete tiles of 20 cm x 20cm x 25 mm thick with grey cement and pigment,set and jointed in neat cement slurry in floors including 15 mm thick screed bed or bedding layers in cement mortar 1:6 for laying tiles complete all as specified and as directed.

Excavating in post holes (or similar holes) each n exc 0.50 Cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, in hard dense soil

M & L for Plain Cement concrete 1:3:6 type C-2 (using 40 mm graded aggregate) in foundations, filling and mass concrete

M&L for mild steel angle, flat work as in posts and struts in fencing incl cutting tops to shape as directed drilling holes, notching for wire etc, flat iron fillets (for scruing wire mesh etc) incl all necessary drilling bolting or riveting etc conforming to Fe 290-Gde E-165 complete.

S&F flat iron in columns clamps, holdfasts wall ties securing fencing etc conforing to Fe-290 Gde-165 complete.

S&F M S Round bars bars 10mm dia and over, cut to length, bent to shape required incl cranking bending spirally for hooping for column hooking ends and binding with and incl mild steel wire annealed not less than 0.9 dia or securing with clips complete.

S & F of Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long 10 to 12 mm dia

Supply only MS galvanised Chain link fencing incl iwire and any type of strands, rails, straining bolts ect all complete all as directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire

S&F for galvanised 2 strand steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails, straining bolts, incl securing or typing at crossing with and provision of G.I wire staples or steel pins etc.

M&L for preparation of steel surfaces of any description over 10cm in width or girth not otherwise described and two coat of synthetic enamel paint over one coat of red oxide.

E/M Part

Taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete (fittings such as switches, ceiling roses pendants, regulators, sockets etc to be measured separately) removing materials to store for keeping in safe custody for reuse at site and making good disturbed surfaces of walls, floors etc.

Taking down any type/ make/ way/ pole etc of sheet metal enclouser distribuion board with all rated MCBs, SPs and SPNs and other connecting accessories complete all as directed.

Taking down carefully all type of tube light/ security light/ lamp holder etc.all type of fittings complete with all connecting accessories.

Taking down unsl Ceiling fans/Exhaust fan any type and size etc complete with all connecting accessories with dimanteling the fan blade and other accessories to be kept in safe custody and depositing in store and all as specified and directed.

M&L for point wiring complete including single core PVC insulated and unsheathed type flexible unsheathed multi stranded 1.5 sqmm copper conductor FRLS cable drawn thrown PVC casing caping and surface/concealed PVC Conduit & accessories having ISI mark to be fixed with proper screws including all accessories/ fittings/ junction boxes /inspection covers etc including hard PVC board and box of required size fixed with wall surface by means of brass screws, for mounting of switches fan regulators etc including 1.5 sqmm (22/0.30mm) 1100 V grade PVC insulated, unsheathed flexible muliti stranded copper conductor FRLS cable as continuous earthwire connected to metallic bodies of luminaries/fans etc. at one end and to common earth duly at other end for.

One light point controlled by one one way switch

One Ceiling fan point controlled by one switch

One Exhaust fan point controlled by one switch

One calling bell point

One 5 Amp socket point controlled by one switch on same board.

One switch socket 5 Amps flush type on Independent board.

All as above item No 5 but using 2.5 Sqmm copper conductor FRLS cable for 15 Amps sockets on independent board and using 2.5 Sqmm PVC insulated unsheathed single core muilti strandard copper conductor FRLS cable 1100 volts as earth wire connecting to as common earth dolly

All as above item No 5 but using 4 Sqmm copper conductor FRLS cable for power point 20 Apms sockets on independent board and using 2.5 Sqmm PVC insulated unsheathed single core muilti strandard copper conductor FRLS cable 1100 volts cable for earth wire connecting as common earth dolly.

Supply and fixing switch piano flush type, single pole, one way, 5 Amps. Make - Anchor/ Legrand/ Havells

Supply and fixing bell push button/switch flush type single pole 5 Amps. Make - Anchor/ Legrand/ Havells

Supply and fixing switch socket combination 2 in 1, 3/5 pin 5 Amps flush type universal . Make - Anchor/ Legrand/ Havells

Supply and fixing switch socket combination 2 in 1, 3/5 pin 15 Amps flush type universal . Make - Anchor/ Legrand/ Havells

S&F POWER UNIT 25 Amp MCB protected power unit of Make : Havells cat No DHDUDP0253016-25 for AC cannection complete all as specefied and as directed.

Supply and fixing ceiling rose 3 terminal PVC polycorbonate isolated body complete.

Supply and fixing bell ding dong AC 230 volts ,single pole making all connection complete.

Supply and fxing PVC holder with 5 watts LED bulb complete.

Supply & fix LED tube light along with fixture, 20 W

Supply and fix LED building security light 30 W IP 65 incl GI bracket made of 40 mm heavy grade GI pipe.

Supply & fix 1200 mm sweep ceiling fans complete and accessories 140-285 V, BLDC moter with remote controlled complete and all as specified and directed Note : Old ceiling fan to be deposited in MES store yard.

Supply & fix exhaust fans AC single phase 230/ 240 V of size 300 mm sweep with louver Note : Old Exhaust fan to be deposited in MES store yard.

Supply and fixing Triple pole and neutral disribution board for MCBs to be fixed 240 volts, 4 ways double door with hinged vertical type having 200 rated copper bus bar with neutral link , complete mounting on teak wooden board in suitable size minimum one inch thick complete all as specified and directed.

Supply and fix 32-40 Amps SPN MCB metallic P&S

Supply and fxing MCB , SP, 10 to 40 Amps, 10 KA , 240 volts complete.

S&F in repair decorative type of LED Garden light of 12 Watts LED type resistance to impact & corrosion, IP 65 protection, heat sink, system efficiency > 100 lmn/ W, CRI between 80-90, color temp 5000-6000 K, complete with LEDs and Driver and incl providing electric connection cable and supporting base of 2-3 feet all as specified & Directed. Make : Philips,Bajaj, Crampton, Havells,Luker and HPL.

S&F in repair decorative type of Post of Lantern for gate light 25 Watts LED type resistance to impact & corrosion, IP 65 protection, heat sink, system efficiency > 100 lmn/ W, CRI between 80-90, color temp 5000-6000 K, complete with LEDs and Driver and incl providing electric connection cable all as specified & Directed. Make : Philips,Bajaj, Crampton, Havells,Luker and HPL.

S&F in repair of FRP junction box for controlling the street/security lights, with four aluminium busbar strips 20X3MM capacity with epoxy insulation fixed on PVC saddles with nut & bolts, cover with color coded caps (RYBB) with and including MCB SP 2.5 Amps capacity size of 170x135x100mm, complete all as directed. Make :- Sintex/ National/ L&T

Supply and fixing sheet metal enclouser disribution board for MCBs to be fixed 240 volts, 2 ways single door with hinged vertical type having 200 rated copper bus bar with neutral link , SPN as incomer complete mounting on tick wooden board in suitable size minium one inch thick complete all as specified and directed.

S&F Water heater storage type, electric,capacity 25 litres.BEE 5 star rated Model Monza DX GHWAMGTWH025 Havells.

S&F in replacement Three phase electronic meters temper proof LCD display with polycarbonate cover 230 V, 10-60Amp, accuracy class-I 50Hz, conforming to IS 13779, IP-54, with parameters to show data, time, current reading, load, PF, voltage and KWH Note : Old Meter to be deposited in MES store yard.

Dismantling /disconnecting LT cables of any size with accessories. Old unserviceable of any type broken or damaged cables fitting on poles / laid in trenches and keeping aside for further disposal.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 2 core

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sq mm 3.5 core.

M & L for DWC HDPE Pipe 50 mm outer dia for UG cable protection passing of cables on wall or floors with shaddling and under ground and all as specified and directed by Engineer-in-Charge.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5 m in depth and getting out all as specified and directed :-

(a) Soft / loose soil

(b) Hard / dense soil

Returning, filling in soil, including spreading, leveling watering and well ramming in layers not exceeding 25cm all as specified and directed.

Removing excavated material not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point of any type of excavation all as specified and directed by Engineer -in-Charge.

M&L for earthing complete with GI earth plate electrode 600 x 600 x 6 mm buried directly in ground vertical to a depth not less then 2.25 mtr below ground level with the top edge of earth plate at a depth of not less then 1.5 mtr below normal ground level using GI earth strip in size 25x4 mm connecting to TPN main DB by means of nuts bolts and washers etc. made out of galvanised iron and GI wire connected to main DBs including necessary excavation earth work PCC (1:3:6) type C1 using 20 mm graded stone aggregate earth chamber 40mm thick RCC cover with PCC (1:2:4) type B1 using 20 mm graded stone aggregate 20 mm dia GI medium grade watering pipe and 40 mm for strip, funnel, protection pipe, adequate quantity of common salt, charcoal etc. and connecting up to main DBs complete all as specified and shown in electrical plate No. 3 of MES Sch Part - 1 complete all specified and directed.

Supply and fix in repair LT indoor panel board made up of 2 mm thick MS Sheet duly powder coated with closing and locking arrangement as per suitable size fixing on wall with wooden plank of 18 mm thick inside panel including taking down and refixing existing electronic energy meter with replacemnt of following new items :- (a) MCB DB TPN 4 way double door -01 No (b) Isolator 4 pole 100A -01 No (Incoming) (c) Isolator DP 40A - 03 No ( Out going)

M/S B.A. GAIKWAD

Dinesh Constructions