Construction work of Ghat and Astha Path on right bank of Ganga River from Deendayal Parking to Chandi Devi Bridge in Distt. Haridwar under Mahakumbh Mela- 2021

Amount

Excavation in foundation for retaining, breast walls etc, in all types of soils and rocks including all lead, lift and disposal of surplus material as per direction of engineer - in - charge, as per drawing and technical specifications Clause 305.1 of MORD Specifiction

Plain/ Reinforced Cement Concrete in open foundations complete as per drawing and technical specifications Clause 802, 803, 1202 & 1203: - Nominal mix 1:3:6

Providing concrete for plain/ reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 Nominal mix 1:2:4

Plain/ Reinforced Cement Concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 (For height upto 5 m): - RCC grade M25

Supplying, fitting and placing HYSD bar reinforcement (Fe 415) in substructure complete as per drawings and technical specification Clauses 1002, 1005, 1010 & 1202.

Plain/ Reinforced Cement Concrete in open foundations complete as per drawing and technical specifications : - PCC Grade M25. Using concrete mixer

Back filling behind abutment, wing wall and return wall complete as per drawing and Technical specification Granular material

Stone masonry work in cement mortar in foundation complete as per drawing and technical specifications Clauses 702, 704, 1202 & 1203: - Random Rubble Masonry in cement mortar 1:4

Stone masonry work in cement mortar in foundation complete as per drawing and technical specifications Clauses 702, 704, 1202 & 1203: - Coursed Rubble Masonry in cement mortar 1:4

Tubular Steel Railing on Medium Weight Steel Channel (ISMC series) 100 mm x 50 mm Providing, fixing and erecting 50 mm dia steel pipe railing in 3 rows duly painted on medium weight steel channels (ISMC series) 100 mm x 50 mm, 1.2 m high above ground, 2 m centre-to-centre, complete as per approved drawings Clause 1706

Construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2)

Dewatering from foundation of abutments and wing walls (with pump capacity 4000 lit per Hr.) including wages of operator and fuel including supply of all material, labour and T&P etc. required for proper completion of the work.

Providing and laying of Empty Cement Bags (Gunny Bags) filled with local sand and tightened using sutli and carriage upto site including preparing subgrade before placing in position, also including supply of all material, labour, T&P etc required for proper completion of the work.

Providing weep holes in Brick masonry/Plain/Reinforced concrete abutment, wing wall/return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V :20H towards drawing foce. Complete as per drawing and Technical specifications

Providing and laying pitching on slopes laid over prepared filter media as per drawing and technical specifications Clause 1302

Providing and laying filter material underneath pitching in slopes complete as per drawing and technical specifications Clause 1302

Brick masonry work in cement mortar in foundations complete excluding pointing and plastering as per drawing and technical specifications Clauses 600, 1202: - in cement mortar 1:4

Brick masonry work in cement mortar in substructure complete excepting pointing and plastering, as per drawing and technical specification Clauses 602, 603, 604, 1202 & 120 :- in cement mortar 1:4

Interlocking Concrete Block Pavement Providing and Laying of Interlocking Concrete Block Pavements having thickness 80 mm as per drawings and Technical Specification Clause 1504

Plastering with cement mortar (1:4), 15 mm thick on brickwork in substructure as per technical specification Clauses 613.4 & 1204

Painting on Steel Surfaces: Providing and applying two coats of ready mix paint including primer coat of approved brand on steel surface after through cleaning of surface to give an even shade as per drawing and Technical Specification Clause 1701

Tubular Steel Railing on Precast RCC posts, 1.2 m high above ground level (Providing, fencing and erecting 50mm dia painted steel pipe railing in 3 rows on precast M20 grade RCC vertical posts1.8 metres high (1.2 m above GL) with 3 holes 50 mm dia for pipe, fixed 2 metres centre to, complete as per approved drawing)

Granular sub-base/base/surface course with local materials (Table 400.13) by mix in place method normal Construction of granular sub-base by providing local material spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at once and compacting with smooth wheel roller to achieve the desired density complete as per Clause 401.4 as per Technical Specification Clause 408

Inverted Choke (Construction of inverted choke by providing, laying, spreading and compacting screening B type/ coarse sand of specified grade in uniform layer on a prepared surface with motor grader and compacting with power roller etc)

Providing steel R.S.Js/built-up steel sections including cutting, welding/rivetting, hoisting, fixing in position for composite girders with shear connectors complete with painting as per drawing and technical specifications Clause 1205.6 13-26-1Steel section (VERTICAL SECTIONS@3M C/C) IN SLANT MANNER

Half-brick masonry with common burnt clay F.P.S. (non-modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level Cement mortar 1:4 (1 cement :4 coarse sand)

Providing and fixing 10x10x7.50 cm Granite stone block hand cut and chisel dressed on top, for paving in floors, drains etc. laid over 20mm thick base mortar 1:4 (1 cement : 4 coarse sand) with joints 10mm wide filled with same mortar including ruled pointing etc.complete as per direction of Engineer-in-charge.

Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). - Medium shade using 50% white cement 50% Grey Cement

Providing and laying 500x500x40 mm thick Turf paver (Turfpave XD) on 150 mm thick sub grade of compacted bed of 20 mm thick nominal size stone aggregate and base course and filling with 150 mm thick jamuna sand, including spreading, well ramming, consolidating and finishing smooth etc. all complete as per direction of Engineer-in-charge

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.

Providing and laying Ceramic glazed wall tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. SIZE 500X500 MM

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Painting top of roofs with bitumen of approved quality @ 17kg per 10 sqm impregnated with a coat of coarse sand at 60 cudm per 10sqm, including cleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil complete :12.15.1 With residual type petroleum bitumen of grade VG -10

Finishing walls with water proofing cement paint of required shade : New work (Two or more coats applied @ 3.84 kg/10 sqm)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer

Providing and fixing white vitreous china squatting plate urinal with integral rim longitudinal flush pipe.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : - W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings : Flat back wash basin of size 630x450mm.

Providing and Fixing factory made PVC door frame made of PVC extruded sections of size 75 mm x 53 mm, having wall thickness 2.0 mm (± 0.2 mm). Both vertical sides of the frame reinforced with PVC profile of cross section size 28 mm x 30 mm x 2 mm thickness (± 0.2 mm) and75 mm x 200 mm long, including reinforcing both ends of the top framewith PVC profile. PVC Door Frame and PVC reinforcement profile to bemitred cut, jointed and fusion welded together, including providing andfixing 3 nos of 125 mm long stainless steel hinges to frame, fixing the frame with jamb with required nos & sizes of anchor dash fastener, all complete as per manufacturer's specification and direction of engineer in-charge.

Providing and fixing 37 mm thick factory made PVC Door shutter, styles and rails made of PVC hollow extruded printed and laminated section having overall dimension 115 mm x 37 mm with wall thickness 2 mm (± 0.2 mm) with inbuilt beading on one side, the styles and rails mitred cut and joint at corners by inserting 2 nos PVC profile reinforcement of size 75 mm x 200 mm long with cross section size of 28 mm x 30 mm having wall thickness 2 mm (± 0.2 mm). Styles, rails and reinforcements to be fusion welded together. Only hinge side vertical style to be reinforced with PVC profile reinforcement in full length. Printed and laminated PVC lock rail of size 110 mm x 37 mm having wall thickness 2 mm (± 0.2 mm) to be welded horizontally with the vertical styles after inserting PVC profile reinforcement as in styles and rails, providing with PVC snap fit beading, panels of 100 x 20 mm printed & laminated and inserting 2 nos 6 mm dia bright steel rod horizontally with both side threaded and tightened with check nuts and washers complete, all as per manufacturer's specification and direction of engineer-in-charge.

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) - Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm).

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : - Float Glass Panes 5.0 mm thick glass panes (weight not less than 12.5 kg per sqm)

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws, etc. complete: - 300x16 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : - 300x10 mm

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :- 125 mm

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. - Single rubber stopper

Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. - Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement :3 coarse sand: 6 graded stone aggregate 20 mm nominal size).

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. - 80x1.25 mm M.S. laths with 1.25 mm th. top cover

Providing and fixing ball bearing for rolling shutters.

Providing and fixing hard drawn steel wire fabric 75x25 mm mesh of weight not less than 7.75 Kg per sqm to window frames etc. including 62x19 mm beading of second class teak wood and priming coat with approved steel primer all complete

Providing and fixing in position factory made non asbestos fibre reinforced aerated cement sandwich wall/roof/floor light weight solid core panels made of light weight cement concrete core composed of OPC cement, pulverized flyash, quick lime, cotton pulp & Gypsum in mortar state mixed with aeration agent in a preset mould. The outer face on both sides of the panels will be non asbestos fibre cement board confirming to IS 14862:2000. These solid wall panels are installed using Galvanized iron steel tracks/C channel of 1mm thick of required sizes as recommended by manufacturer’s and fixed to floor and RCC soffit in plumb to each other with steel screw/ fasteners. The panel shall be fixed vertically with tongue & groove joint with cement based polymer modified jointing compound. The exposed surface finished with fibre mesh/glass fibre tape with polymer based jointing compound having superior flexibility. Panels should be used as floor & roofing with additional structural support, steel or RCC depending upon the design. All the operation shall be completed in all respect as per drawings, Manufacturers specifications and under the overall direction of Engineer-in-Charge (Cost of all the material is included except “tracks/C channel” which will be paid separately). 26.50.1Non load bearing panels 50mm thick of required size (minimum 4mm thick fibre cement board)

40 mm thick fine dressed stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1 cement : 5 coarse sand), including pointing with cement mortar 1:2 (1 cement : 2 stone dust) with an admixture of pigment to match the shade of stone. - Red sand stone

Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab.

Providing and laying 18 mm thick granite stone slabs, gangsaw cut, mirror polished, pre-moulded and pre-polished, machine-cut to required size and shape, of approved shade, colour and texture in footpath, flooring, road side plazas and similar locations, laid over 20mm thick base of cement mortar 1:4 (1cement: 4 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. complete as per direction of Engineer-in-Charge: - With granite stone of area less than 0.50 sqm

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment tomatch the shade of the slabs, including rubbing and polishing complete.

Supplying & making of end terminations with brass compression gland and Al. lugs for following sizes of PVC insulated and PVC sheathed/ XLPE Al. conductor cable of 1.1 KV grade as required.

3½ X 185 sq. mm (57mm)

3½ X 70 sq. mm (38mm)

3½ X 50 sq. mm (35mm)

4 X 35 sq. mm (32mm)

4 X 16 sq. mm (28mm)

4 X 10 sq. mm (25mm)

2 X 10 sq. mm (19mm)

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required. (150 mm dia)

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. (Above 95 sq. mm and upto 185 sq. mm)

Laying of one number PVC insulated & PVC sheathed/ XLPE Power cable of 1.1 KV grade of following size in the existing RCC/HUME/METAL pipe as required.

Upto 35 sq.mm

Above 35 sq. mm and upto 95 sq. mm

Supplying and making cable route marker with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) of size 60 cm X 60 cm at the bottom and 50 cm X 50 cm at the top with a thickness of 10cm including inscription duly engraved as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Earthing with G.I. earth Plate 600mm x 600mm x 6mm thick including accesssories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long with charcoal or coke and salt as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Providing and fixing 6 SWG dia GI Wire on surface or in recess for loop earthing as required.

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required.

63 mm dia (OD-63 mm & ID-51 mm nominal)

90 mm dia (OD-90 mm & ID-76 mm nominal)

120 mm dia (OD-120 mm & ID-103 mm nominal)

Two pole structure: Supplying, fixing, testing and commissioning of two pole structure for receiving 11 KV 3 phase incoming line comprising of :- Supplying, fixing, testing and commissioning of two pole structure for receiving 11 KV 3 phase incoming line from Electricity board comprising of :- 2 nos Steel tubular pole 11 mtrs long, swaged type 410 SP-55 as per IS- 2713. Cement Concrete foundation (1:2:4), 1850 mm below ground abd 450 mm above including excavation and refilling etc. Steel section, channels, angles, flats, clamps, GI nuts, bolts and required hardware etc. of different sizes for cross arms, bracings, supports etc. for pole, insulators, lightning arrestors, GO switch, GI pipe for 11 KV cables, supports for terminations, etc. including anti climbing barbed wires, danger plate etc. 11 KV class disc/pin/support insulator complete with clamps and fixing hardware etc. 3 nos, one per phase, 11 KV station class thyrite type lightning arrestors complete with mounting arrangement on the incoming overhead line along with earthing connections as required. 1 set of G.O. Air break switch with DO fuse 200 Amp. With gang operated devices, with pad locking arrangement. Operating rod, supports, complete with operating handle and locking arrangement 1 Lot - ACSR Conductor and connectors for tapping the connection and for connections with in four pole structure with heat shrinkable insulating sleeves for protection of connections etc. 1 lot -Earth connection with 50 x 6 mm GI Strip.

Transformer: Supply, fixing, testing and commissioing of 160 KVA, 11kV/ 433 volt, 3 phase, 4 wire 50 Hz. oil Type ONAN Cu. wound Transformer for outdoor installation with cable box at primary and secondary end, silica gel breather (Completely Self Protected) , 4 star rating as per nigam specification etc. completed as required.

EX. LIGHTING FEEDER PILLARS: Design, Manufacturing, supplying, fixing in position, testing and commissioning of the following front operated front access 2mm thick CRCA steel enclosure free standing, water, dust and vermin proof outdoor type Feeder pillars with IP-54 protection hinged and lockable doors complete with interconnections copper crimping lugs, brass glands bonding to earth and painting, suitable for use at 415 volts, 3 phase 4 wire 50 Hz system . The panels fault withstanding capacity shall be of 25 MVA at 415 volts. All live accessories part shall be shrouded and all equipment shall be finger touch proof. The bus bars shall be of colure coded with Heat shrinkable PVC insulated sleeves.The job includes all labour & material required for cement concrete plat-form of suitable dimensions. INCOMING: 1 no. 63A, 415V, 4P MCCB of 16kA. 1 no. 70A 4P Contactor with time switch. 1 set of Phase indicating lamp with MCB. BUS BARS: 150A TPN bus bars of aluminium alloy. OUT GOINGS: 3 Nos. 32A 4P MCB of 10kA. 8 Nos. 16A DP MCB of 10kA.

Supplying of 1C x 70 sq.mm XLPE Al. armoured cable, 11 KV grade, conforming to IS : 7098 Part-II and as per specification.

Supply of the following size XLPE insulated PVC sheathed aluminium conductor armoured cables as per IS:7098(part-1)

3 1/2 x 185 sq.mm

3 1/2 x 70 sq.mm

3.5C x 50sq.mm

4C x 35 sq.mm

4C x 16 sq.mm

4C x 10 sq.mm

2C x 10 sq.mm

EXTERNAL LIGHTING: Street Lighting Pole 7.00M. Double Arm: Supply, Installation, testing and commissioning of Galvanised steel octagonal pole with double arm bracket, with mounting height of 7 Mtr above ground level for street lighting .minimum sheet thickness 3mm or as per design whichever is higher, with embedded/built-in/separate 3-way junction box (including MCB, connector, 3C x 2.5 Sqmm Cu PVC flexible cable within the pole etc.) with IP65 protection (suitable for looping & termination of 4CX16 sqmm Al XLPE armoured cable), hot-dip galvanised internally and externally to 80 microns DFT. (2 nos. street light luminaires per pole. Foundation and foundation bolts is in scope of street light supplier/vendor. )

High Mast 20M. with 12 Lamp Carriage: Design, Manufacture, Supply, installation, testing & commissioning of 20M high mast complete in all respects including electrically operated raising and lowering gear, double-drum winch with steel wire ropes, integral power tool, lantern carriage, top pulley arrangement complete with hot-dip galvanised finish, RCC foundation with excavation in soil, foundation bolts, anchor plates, nuts, washers including multicore copper conductor cable (Trailing cable) in two circuits (each for 12 nos. 250W LED Light Fixture) of suitable current-carrying capacity between top carriage and the base terminal (inside mast) including provision of outdoor type double-door feeder pillar made of 14swg CRCA sheet with powder-coated paint, comprising of suitably rated one no. incomer TP MCCB of 25KA and two nos. outgoing circuits with TP MCB(s) of 10KA, Auto ON/OFF with astronomical switch, contactor(s) , timer toggle switches, interconnecting copper wiring, etc. as required suitable for operation on 415V, 3-phase, 50Hz, AC power supply. The scope of work also includes installation of 12 nos. floodlight luminaires, provision of lightning arrester, one no. LED obstruction light fixture erected with lantern carriage and connected in two separate wiring/connections from mast control board, extending earth strip from feeder pillar to mast body, connections, interconnections, complete as required and as specified.

Supply of 250W LED FLOOD Light Luminaire with initial system lumen of 25000 lumen and minimum system efficacy ≥ 100lm/W. Housing shall be Die Cast Aluminium . IP66 , Optics:Toughened Glass. The operating CCT shall be 5700K with CRI of ≥70. The luminaire shall be with BIS Registered electronic driver with input voltage range of 150 to 270V , THD ≤ 10% & PF ≥ 0.95, 50,000 Hrs LED Life with L70 Criteria.The LED Driver shall be easily avaiable in India for repair and service. The LED shall be SMD type. Luminaire shall have minimum surge protection of 4KV.The luminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along with Photo Biological Safety Standard. similar to Wipro Cat No LF20-342-060-57-G2 or eqv

Supplying, erection, testing and commissioning of pole of 3 meter height.Finish : Coated with epoxy zinc phosphate primer and finished using environmentally stable polyurethane based paint. Applications : Ideally suitable for entrance to memorials, pathways, garden, residential road and similar locations. Installation : Surface mounted with base plate and fitted on a pre formed foundation, with 20W LED post top Light , prewired control box with service door including lock and safety chain, supplying and fixing of 6 Amp SP MCB C-Series and 32 Amp heavy duty connector etc. for making connections with suitable size of copper wire and thimbles / lugs in the connector box. The pole shall be installed in cement concrete foundation (1:3:6) i.e. 1 cement, 3 coarse sand and 6 graded stone with the help of anchor bolts of 3/4" dia by laying iron bar mesh fabricated with 6mm dia iron bar, earthing of pole, connection etc. complete as required. (The light shall be of Eq. to K Lite cat no. 6619).

Supply, fixing, Testing & Commissioning of Surface mounted LED bollard 16W with IP 65 rating, luminaire made of extuded aluminium alloy (grade 6063) with die-cast aluminium components and non corrosive SS fasteners, reflector system made of spun aluminium(powder coated white), non yellowing UV stabilized polycarbonate clear diffuser, silicon gasket, Cast Iron / aluminium mounting plate for bolting onto a foundation. Luminaire can be aligned on the mounting plate around 360°.The Light shall be fixed with proper nut/screw. The job includes cost of labour, Civil work and petty material required to complete the job to the entire satisfaction of EIC of the work.(The Light shall be Eq. to KLite cat no. KP 7050).

DG SETS: Providing ,Installing and commissioning of Silent type Diesel generator set along with having Prime Power rating of 160 kVA ,415 volt at 1500 Rpm,0.8 lagging power factor at 415 v suitable for 50 Hz, 3 phase system & 0.85 load factor and consisting of following. Diesel Engine 4 stroke water cooled ,Electric start of suitable BHP AT 1500 RPM suitable for above output of alternator at 40 degree c,50 % RH & at 1000 meter MSL and conforming to BS 5514,BS 649,IS 10000,Capable of taking 10 % overloading for one hour after 12 hour of continuous operation. The engine will be fitted complete with all required accessories. Engine mounted instrument panel fitted with and having digital display for following Start -stop switch with Key water temperature indication. Lubrication oil pressure indication Lubrication oil temperature indication. Battery Charging Indication. RPM Indication. Over speed indication, Low Lub. Oil trip indication, Engine Hours indication. Alternator.Synchronous alternator rated at 160 KVA,415 volts at 1500 Rpm ,3 Phase 50 Hz,AC supply with 0.8 Lagging power factor at 40 Degree C,50 % RH & at 1000 Metre MSL.The alternator shall be having SPDP enclosure,Brushless,Continous duty, Self excited and self regulated through AVR conforming to IS: 4722/BS 2613 suitable for tropical condition and with class-F/H insulation. Base Frame & Foundation. Both the engine and alternator shall be mounted on suitable Base frame made up of MS channel with necessary reinforcement which shall be installed on suitable cement concrete foundation and vibration isolation arrangement as per recommendation of manufacturer. Exhaust System. Dry exhaust manifold with hospital exhaust silencer and catalytic convertor. Starting System. 12V/24V DC Starting system comprising of starter motors : Voltage Regulator and arrangement of for initial excitation complete with suitable nos of batteries(25 Plates,180 Amp. Hours Capacity Lead acid type)as required as per specification. Acoustic and weather proof enclosure with arrangement fresh air intake for cooling of the engine & alternator,extraction,discharging hot air in to the atmosphere as per specification

Supply, fixing and commissioning 225 ltrs capacity 16 SWG MS steel, Disel oil Tank with manhole, PVC gauge, inlet and outlet connections with gate valve, drain plug, piping between tank and engine vent etc. mounted on suitable MS staging to maintain gravity flow of diesel oil From tank to DG set including painting etc. as required.

Supplying and fixing exhaust gas piping of following dia welded black MS,B class pipe conforming to IS :3589 cut to required lengths and installed with necessary Bends ,support and clamps, and anti-vibration mounting, insulation of exhaust system with mineral wool/Rockwool,50mm thick wire mesh & aluminium cladding etc as required as per specification including Supplying, Fabricating and installation of MS fabricated support for silencer complete with welding, grouting and painting etc. including providing the suitable support on DG set side and other side complete as per the instruction of the Engineer in charge / Architect (1x100mm dia Class - B MS pipe.)

Supply, fixing testing and commissioning of 25 mm dia. Class C, MS pipe with welded joints including all accessories valves etc.

Copper control cable amoured type XLPE 1.1KV grade

2Cx2.5sqmm

4Cx2.5sqmm

12Cx2.5sqmm

Termination of the above cables

Bullet Camera: Supply, installation, testing and commissioning of Bullet Camera having Image Sensor: 1/2.8” Progressive Scan CMOS; Min. Illumination: Color-0.005 Lux @ (F1.2, AGC ON) 0 Lux with IR, Color-0.0068 Lux @ (F1.4, AGC ON) 0 Lux with IR; Shutter Speed: 1/3 s to 1/100,000 s, Slow Shutter supported; Day & Night: IR Cut Filter; Digital Noise Reduction: 3D DNR; WDR: 120dB ; 3-Axis Adjustment-Pan: 0° to 360°, tilt:-0° to 90°, rotate-0° to 360°; Focal length: 2.8 to 12 mm, Motorized zoom Lens; Aperture: F1.4, H.264 Type: Main Profile/High Profile , H.265 Type: Main Profile , Video Bit Rate: 32 Kbps to 16 Mbps; Audio Compression: G722.1/ G711ulaw/ G711alaw/ G726/ MP2L2; Audio Bit Rate: 32 to 128kbps; Day/Night Switch: Auto/Schedule/Triggered by Alarm, Alarm Trigger: Motion detection, video tampering, network disconnected, IP address conflict, illegal login, HDD full, HDD error, Alarm input, Alarm output; Built-in Micro SD/SDHC/ SDXC slot, up to 128 GB; IR Range: Up to 50m, Regulatory: UL, CE, FCC; Protection Level: IP67, IK10 TVS 2000V Lightning Protection, Surge Protection and Voltage Transient Protection. Make-Tyco/ Mobotix/ Pelco

Network Video Recorder: Supply, Installation, Testing and Commissioning of 4U Rack mounted single chassis Network Video Recorder with DVI-I, HDMI, 1 display port, max 2 simultaneous monitors, connect min. 128 full HD (1920x1080p) cameras per appliances.It must continuously record up to 800 Mbps (Windows).1200 Mbps (Linux)of video for high concentration of high definition IP cameras.Local client display rate:. Windows OS: up to 700 frames per second.Linux OS:up to 1100frames per second. NVR shall have RS-485serial port capabilities to communicate with serial devices. It should support 3/1Alarm Inputs/Output. NVR shall have Dual Hot Swap redundant Power Supplies. Operating Temperature 40° - 95°F (4.5° - 35°C). Operating System must be support Windows/Linux both platform & Should Support up to 128 Cameras. Make-Tyco/ Mobotix/ Pelco

Hard Disc Drive: Supply, installation, testing and commissioning of Enterprise Class 6TB Hard Disc Drive. Make-WD/Seagate

Video Management System: Supply, installation, testing and commissioning of Video Management System (VMS) software to view live and recorded video from capture cards and IP devices connected to local and wide area networks. The VMS software shall have a client/server-based architecture that can be configured as a standalone VMS system with the client software running on the server hardware and/or the client running on any network-connected TCP/IP workstation. The VMS server software shall also have the ability to be installed on an IP edge device, such as an IP camera or encoder, that allows for 3rd party applications—allowing the device to serve both as a server and as an IP video recording device. The VMS shall not charge for the number of concurrent clients (min. 50 thick clients and 16 mobile clients to be provided along with VMS). Make-Tyco/ Mobotix/ Pelco

Outdoor Armored Cable: Supply & Laying of 4-pair Category 6 outdoor armoured cable as per TIA-568C.2, tested till 250 MHz, certified Fire-Retardant, Low-Smoke & Zero-Halogen as per IEC 60332-1, IEC 61034-2 & IEC 60754-1 respectively. Make-Legrand/Siemon/Panduit

Feeder Pillar: Supply, installation, testing & commissioning of Feeder Pillar having IP55 Outdoor 17U Network Rack with Hood and FAN for Field Devices. The Rack box shall be provided with external earthing lugs 5 socket; Power terminaton with MCB for proper fixing through RCC base as per site requirements is under bidder’s scope. Make-Rittal/ Satellier/ Valrack.

PoE+ Switch: Supply, installation, testing & commissioning of 12 Port Power-over-Ethernet (PoE+) Switch with 2 SFP slots 12 x 10/100/1000 Base-T PoE+ ports and additional 2 100/1000X SFP PORTS Should support PoE+ as per IEEE 802.3 at with PoE budget of 100W. Should support STP, RSTP, MSTP, IGMP v1/v2/v3 snooping, STP root guard, Voice VLAN, MLD snooping (MLDv1 and v2), IEEE 802.3ac VLAN tagging IEEE 802.17/equivalent for sub 50ms ring protection in following scenario: single, dual fibre cuts in ring and when fibre cut at common shared link in between two or more rings. Make-Juniper/ Cisco/ Extreme

Outdoor Junction Box: Supply, installation, testing & commissioning of IP55 Outdoor Junction Box For Field Devices at camera side. JB must be of appropriate size to house different components as per CCTV system design confirming. The junction box shall be fixing along with weather proof clamping with pole as per site requirement.

Fibre-Optic Patch Panel: Supplying & Fixing of LC-style fully loaded Fiber Optic Patch Panel (FOPP), 19" Rack Mount, having all accessories including coupler plates pre-loaded with 12 nos. LC couplers (OM3) complete in all respects. Make-Legrand/ Siemon/ Panduit

Fibre-Optic Patch Cable: Supplying & fixing Fiber Optic Patch Cable (LC-LC), 3 Mtrs. Long, ISO/IEC-11801-OM3 50μ Duplex, LSZH,All patch cords shall conform to EIA/TIA-568C.3 and ISO/IEC-11801,Shall be Duplex Multi Mode Fiber Optic Patch Cords OM3 50μ,Shall support network line speeds up to 10 Gbps.Shall have LC-LC Connector connectors at the ends complete in all respect. Make-Legrand/ Siemon/ Panduit

Pigtail Connector: Supply & fixing OM3 50/125μ Type Pigtails of ISO/IEC-11801-OM3 with LC Type Connectors for terminating fibers on the FOPP complete in all respects. Make-Legrand/ Siemon/ Panduit

SFP+ Transceiver: Supply, installation testing and commissioning of Small Form-factor Pluggable (SFP+) Transceiver with 10 Gigabit Ethernet SR Optics. Make-Juniper/ Cisco/ Extreme

Metallic Armored Fibre Cable: Supply, installation, testing & commissioning of 50μm, 6-core Multi mode OM3 metallic armored Fiber cable as per ISO/IEC-11801, Shall be able to meet Gigabit & 10 Gigabit Ethernet performance up to 300 meters requirement specified by IEEE 802.3z (1000 Base-X) & IEEE 802.3ae (10G Base-X) Tensile load should be 800 Newton or higher and crush resistance should be 2000 Newton or higher , the fiber construction can be unitube or multitube, but tensile and crush resistance parameters should be matched, the jacket shall be LSZH complete in all respects. Make-Legrand/ Siemon/ Panduit

Client Workstation: Supply, installation, testing & commissioning of Client Workstation having Intel Core i5 orginal motherboard, 16 GB RAM, Video graphics card 2 GB Licensed Windows 8 Professional (64 bit) and 1 TB Hard Disk with Web camera,Printer and finger print scanner. Make-HP/ Dell/ Lenovo

Television Monitor: Supplying, Installation,Testing & Commissioning of 55 " LED Full HD TV Resolution 1920 x 1080 ,Contrast Ratio (Typical) 5000:1,Built-in Speaker (10W + 10W), Magic Clone (to USB), Auto Source Switching & Recovery, Lamp Error Detection, Super Clear Coating, Temperature Sensor, Plug and Play (DDC2B), Pivot Display, Clock Battery, PIP/PBP, Video Wall (10x10), Image Rotation, Button Lock, HDCP Support,Smart Scheduling, Smart F/W update, Built-In MagicInfo Premium-Swith Mounting Brackets as per Technical Specification complete in all respects. Make-Sony/ Samsung/ Panasonic

Uninterrupted Power Supply: Supply, installation, testing & commissioning of online 1KVA fully Microprocessor-based UPS System suitable for Single phase, AC 50Hz. input supply comprising of following features: High-frequency PWM Inverter using IGBT Technology, Manual by-pass switch, LCD display, SMF VRLA Batteries with 30 minutes back up time for full load, including interconnecting cables and Battery Rack. Make-APC/ Eaton/ Elnova

Two-way Long Throw Horn Speakers: Supply, installation, testing, and commissioning of two-way long throw horn speakesr, Transformer power taps: 60-30-16-8 W @ 100V or more, Woofer: 6.5 inch cone, Tweeter : 1 inch horn driver, SPL 1W/1m: 106 dB, SPL max. 123dB, Dispersion (H x V): 110° x 80° or more, IP Rating: 66, depth: 290mm, height: 250mm, complying with EN62368-1:2014, EN55020:2007+A12:2016, EN61000-3-2:2014, EN55013:2013 etc. required complete as per specifications and description. Make- Bosch/Ahuja/Megha

Pole-mount Bracket: Supply, installation, testing, and commissioning of W-shaped pole-mount bracket for LTH speaker from the same (OEM) make only, (no external or cutomized allowed) etc compete required as per specifications. Make- Bosch/Ahuja/Megha

Amplifier: Supply, installtion, testing and commissioning of digital amplifier having 100V transformers, High thermal efficiency, Convectional cooling with temperature controlled cooling fan, APC limiter to automatically avoid overloads of incoming audio signal, Input connections: 4 x unbalanced on RCA with pass-through + 4 x balanced on Euroblock, Input sensitivity: 0 dBV /1 V, Input impedance: 22 kΩ, S/N ratio: >101 dB A-weighted, THD: < 0.3 % , Frequency response: 50 – 20 kHz + 0 / - 3 dB, Protection circuits: over-current, over-temperature / monitoring, Power amp topology: Class-D, Power supply: 2 x switching mode power supply, Electromagnetic Compatibility Directive: EN55013:2013, EN61000-3-2:2014, EN55020:2007+A12:2016, certified from Low Voltage Directive: EN62368-1:2014, Cooling: convectional and temperature controlled fan, Operating temperature range: 0 to 40°C, output voltage tappings: 100-70-50-35 volts - 4 ohms, Output power RMS bridged 100 volts: 2 x 480 watts, etc. complete required as per specifications and description. Make- Bosch/Ahuja/Megha/Daksh

Digital Signal Processor: Supply, installation, testing and commissioning of audio control Digital Signal Processor capable of being mounted in a standard 19-inch equipment rack and will take up 1 rack units in height with a maximum built in depth of 313mm/12.32 inches and a weight of at least 3.8kg/8.38lbs. The preamplifier inputs shall include at least 6 single balanced mic/line inputs using euroblock connectors which can be configured as mono or stereo and be supplied with 24v phantom power and six single unbalanced line inputs using RCA connectors which can be configured as mono or stereo The preamplifier shall include 8 single unbalanced outputs using RCA connectors configurable to be any combination of mono, stereo, 2.1, mono crossover or stereo crossover outputs. The frequency response of the preamplifier shall be 20-30kHz Zone combining shall be available in the preamplifier etc complete required as per specifications and description. Make- Bosch/Ahuja/Megha/Daksh

Media Player: Supply, installation, testing and commissioning of Media Player, DAB/FM RDS Tuner, CD/MP3 from Disc, SD-card or USB memory stick, RS232 control, IR remote included etc complete required as per specifications. Make- Sony/Samsung/Panasonic

Feeder Pillar: Supply, installation, testing & commissioning of Feeder Pillar having IP55 Outdoor 17U Network Rack with Hood and FAN For field devices. The Rack box shall be provided with external earthing lugs 5 socket. Power terminaton with MCB or more proper/sturdy fixing through RCC base as per site requirements is under bidder’s scope. Make- Rittal/ Satellier/ Valrack.

Supply & Laying of 1.5 sq.mm. multistrand PVC sheathed Two Core Twin Twisted Speaker outdoor armoured Cable in Exiting PVC Conduit. Make: Finolex/V imco/ Polycab

Surface Dressing of the ground including removing vegetation and in-equalities not exceeding 15cm deep and disposal of rubbish.

Supply and stacking of good earth at site including royalty and carriage complete.

Spreading good earth in required thickness and graded formations as per directions of the officer in charge. Cost of earth to be paid seperately.

PLANTATION OF TREES: Preparation of pits for trees by excavating 1.0 x 1.0m and 1.0m deep, placing in position the specified tree in the pit, refilling the excavated pit with good earth after breaking clods and mixing with manure in the ratio 4:1, alongwith soil improvement nutrients ( 0.5 kg of gypsum, 20 gms each of DAP and carbofuran 3G per pit), staking and watering as directed by officer-in-charge all complete.

PLANTATION OF SHRUBS: Preparation of pits for large shrubs by excavating 0.6 x 0.6m and 0.6m deep, placing in positiion the specified shrub in the pit, refilling the excavated pit with good earth after breaking clods and mixing with manure in the ratio 4:1, alongwith soil improvement nutrients ( 0.25 kg per of gypsum, 20 gms each of DAP and carbofuran 3G per pit), staking and watering as directed by officer-in-charge all complete.

GROUND COVER & HEDGES: Preparation of pits for ground cover, hedges and climbers by excavating as per plan to depth of 0.30m., removing all foreign bodies, placing in position the specified shrub in the pit, refilling the excavated area with good earth after breaking clods and mixing with manure in the ratio 4:1, along with soil improvement nutrients (0.25 kg of gypsum, 10 gms each of DAP and carbofuran 3G per sqm.),staking and watering as directed by officesr-in-charge all complete.

Anti Termite Treatment: Providing and Applying anti termite treatment of lawn area through Premise 30.50 % IP or equivalent one litre diluted in 499 litres of water or chemical and applying the solution @ 1.00 litre solution per sqm lawn or bed area (two application) or Chloropyriphos 20% in the ratio of 1% concentration including cost of chemical and as directed by the officer in charge.

Plant Supply

Plumeria Alba (1.80 m height, 150 mm girth)

Delonix Regia (4.50 m height, 350 mm girth)

Cassia Semia (4.50 m height, 200 mm girth)

Pilkhan (4.50 m height, 480 mm girth)

Cassia fistula (4.50 m height, 180 mm girth)

Kadamb (4.50 m height, 300 mm girth)

Chorisia (1.20 m height, 480 mm girth)

Jacaranda M. (1.50 m height, 300 mm girth)

Erythina Indica (4.50 m height, 300 mm girth)

Bottle Brush (3.00 m height, 200 mm girth)

Bauhinia V. (4.50 m height, 300 mm girth)

Shrubs

Lantana Sellowiana

Lantana Depressa

Lilly

Caesalpinia

Cassia Biflora

Calliandra

Oleander

Bougainvillea

C - GROUND COVER & HEDGES

Clerodendrum Inerme (min.10 nos. polybag/ )

Wadelia Trilobata (min.36 nos. Polybag/ )

Dianella Variegated (min.25 nos. Polybag/ )

M/S RAM PAL SINGH MUKHTYAR AHMAD CONTRACTOR