ADDN ALTN TO MD ACCN AT DEHRADUN

Amount

BUILDING WORKS

Dismantling of plain or corrugated steel sheeting any gauge, thickness including nanital or similar pattern as in roof coverings complete all as specified and directed.

Dismantling timber scantling 40 sq cm and over in section, in any position for Framed / unframed work complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc. Laid, bedded and pointed in any mortar complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and paving n. exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

Demolition of cement concrete reinforced of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Demolition of concrete of any description and in any position not otherwise specifically provided for. Complete all as specified and as directed. (Sunken floor/roof padding)

Demolition of brick work in cement mortar including all quoins, arches, pillars etc, but excluding ashler facings, dressed stonework and precast concrete articles complete all as specified and as directed.

Taking down cement plaster of any description, thickness on brick, stone, concrete surfaces including racking out joints, hacking for key, scrubbing down with water, removal of rubbish and cleaning, etc complete all as specified and directed.

Taking down Chowkats or frames with shutters (without taking off shutters from the frame) exc 1.50 sqm but n.exc 4.0 sqm each and removing from site including making good disturbed portions of wall with new or old bricks, lintel, cills etc in CM 1:4 complete all as specified and directed.

Taking down Chowkats or frames with shutters (without taking off shutters from the frame) n.exc 1.50 sqm each and removing from site including making good disturbed portions of wall with new or old bricks, lintel, cills etc in CM 1:4 complete all as specified and directed.

Dismantling of cast iron / PVC / AC / SGSW pipes alongwith fittings and accessories upto (100/75) mm dia jointed in cement mortar and taking out of walls, floors or trenches, if required complete all as specified and directed.

Taking up or down 15 mm steel tubing and connections complete all as specified and directed.

Taking up or down 20 mm steel tubing and connections complete all as specified and directed.

Dismantling of water tanks capacity exc 250 ltrs and n.exc 500 ltrs complete all as specified and directed.

Dismantling of water tanks capacity exc 500 ltrs and n.exc 1000 ltrs complete all as specified and directed.

M&L PCC 1:4:8 type D 2, 75 mm th (using 40mm graded stone aggregate) as in floor , sub base & pavings complete all as specified and directed.

M & L for 25 mm thick PCC 1:2:4 type B-0, using 12.5 mm graded stone aggregate as in floors, to receive surface of tile complete all as specified and directed.

M&L for Non skid coloured ceramic tiles 400 X 400 X 7 to 8 mm thick (square/ rectangular) on floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:6. Complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified and directed.

M&L for coloured Vitrified double charged tiles 8-9 mm thick (square/rectangular) any shade of size (600 x 600 ) mm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with and including 15 mm thick screed bed or bedding layer in CM 1:4 complete all as directed.

M&L for coloured Vitrified double charged tiles 8-9 mm thick (square/rectangular) any shade as in Skirting, riser etc (length of tiles not less than 600 mm) set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick rendering in CM 1:4 complete all as specified and directed,

M&L Glazed ceramic tiles coloured 300mmx 450mm , 7 to 8 mm thick, set and jointed in neat cement slurry and pointed in white or colour cement to match on vertical surfaces of wall incl 10 mm thick rendering on brick surface in CM 1:4. complete all as specified and as directed.

M & L for 18 to 20 mm thick prepolished machine cut kota stone tile as in flooring incl 20 mm th cement screed base in CM 1:6 , laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including necessary grinding, rubbing and polishing. complete all as specified and directed.

All as per item no 25 but on vertical surfaces of walls as in skirting and dados incl 10mm th backing coat in CM 1:4. Complete all as specified and directed.

M & L for 16 to 18 mm thick granite(Zed Black colour as approved by GE) stone slab machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing as in kitchen platform/dado/skirting /plateform counter top WHB in cluding cutting holes for oval shape /urinal partitions etc. including 15 mm thick cement screed bed 1:6 CM in horizontal or vertical surfaces including grinding the edges half round and polishing complete all as specified and directed by Engineer-In- Charge.

M & L for 16 to 18 mm thick granite(Ruby Red colour as approved by GE) in steps / staircase machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing including 15 mm thick cement screed bed 1:6 CM in horizontal or vertical surfaces including grinding the edges half round and polishing complete all as specified and directed by Engineer-In- Charge.

M & L for 16 to 18 mm thick granite(Ruby Red colour as approved by GE) stone slab in risers / dado of steps / staircase machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing etc. including 10 mm thick cement screed bed 1:4 CM in vertical surfaces complete all as specified and directed by Engineer-In- Charge.

M & L for 20-25 mm thick red colour rough dressed stone slab as in plinth protection, bedded and jointed in cement mortar 1:6 & pointed in cement mortar 1:3 over 20 mm thick screed bed in CM 1:6 over 75 mm PCC 1:4:8 type D-2 using 40 mm graded stone aggregate . complete all as specified and directed.

M&L for brick work with sub class 'B' bricks old size bricks, straight or curved on plan exc. 6 m mean radius, built in CM (1:6) complete all as specified and directed.

All as per item No 31 above but except bricks complete all as specified and directed.

M & L for 15mm thick ready mix internal sand faced cement plaster on brick or concrete surfaces including providing as per manufacturers specifications, surfaced finished even and fair complete all as specified and directed.

M & L for 15mm thick ready mix external sand faced cement plaster on brick or concrete surfaces including providing & mixing water proofing compound as per manufacturers specifications, surfaced finished even and fair complete all as specified and directed.

M & L for 10mm thick ready mix sand faced cement plaster on concrete ceiling surfaces including dubbing coat after applying one coat of alkaline anticorrosion chemical coating having specific gravity of 1.2 ti 1.22 upon exposed reinforcement as per manufacturers instructions etc complete all as specified and as directed

M & L for rendering 5 mm thick in CM 1:3 as on concrete surface on ceilings finished even and smooth without using extra cement complete all as specified and directed.

Taking down existing un-serviceable water proofing treatment from roof slab and cleaning the roof slab by wire brush and removing WPT felt exc 500 mtr but not exc 1.50 Km etc complete all as specified and as directed

M&L for cement concrete 1:2:4 type, B0 using 12.5 mm graded stone aggregates as in copings, roof padding/staging of water tank etc including necessary fromwork, weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed

M & L for cement concrete 1:5:10 type E-2 using 40 mm graded brick aggregates as in sunken portion etc complete all as specified and as directed.

M & L for applying cement slurry over existing roof surface @ 3 Kg/Sqm incl mix with water proofing liquid @ 0.15 ltr per 50 kg cement bags as per manufactures instructions complete all as specified and directed.

M&L for rendering 10 mm thick , in cement mortar 1:4 over RCC slab, mixed using water proofing compound liquid @ 200 ml per bag of cement. Complete all as specified and directed.

M & L for two coats of elastomeric compound i.e super latex of Dr fixit Pidilite-302 super latex / Fosroc-brush crete / Cico Tape Crete on concrete surface after cleaning of sunken portion (vertical or horizontal) by removing all the loose mortar laitance dirt, dust etc by chisel, hammer, wire brush, jute, brush and air blower. complete all as specified and directed.

S & F for 32mm dia GI pipe, medium grade as in spout pipe in sunken floor complete all as specified and directed.

M & L for water proofing treatment to non-accessible roof slab with APP based madified polymeric membrane as per manufacturers instructions with following course of description below:- (a) Applying a priming coat of bituminous primer @ 0.30 kg / sqm, till the surface is properly impregnated. (b) A coat of hot blown bitumen 85/25 @ 1.2 Kg / Sqm over bitumen primer. (c) Providing APP based 5 layer polymeric membrane minimum weighing 3.6 kg / sqm and minimum 3 mm thick reinforced with polyester non-woven fabric (weight not less than 150 gms /sqm) centre core, laid on primed surface by forced applications as per manufacturers instructions with side over lap of 75mm and end overlap of 100 mm. All overlap joints shall be sealed thoroughly by thermo fusing both the membrane layer (torching overlap by propane or butane gas torch) and sealing it with the help of hot trowel. The overlap joints shall be made as a monolithic layer. (d) Apply two coat of bituminous aluminium paint @ 0.20 Kg / Sqm over APP membrane. Note:-

1. The work of water proofing treatment shallbe got executed authorised applicator of the manufacturer only and 10 year company back warranty to be submitted by contrcator. 2. The work is required to be carried out at non-accessible roof slab upto triple storey. The contractor shall make arrangement of scaffolding, safety and security of workers and arrangement for approach to roof. The rates quoted shall be deemed to be included for these items.

M & L for water proofing treatment to accessible roof slab with APP based modified polymeric membrane as per manufacturers instructions with following course :- (a) Applying a priming coat of oil based bituminous primer @ 0.30 kg / sqm, till the surface is properly impregnated. (b) Providing APP based 5 layer polymeric membrane minimum weighing 3.6 kg / sqm and minimum 3 mm thick reinforced with polyester non-woven fabric (weight not less than 150 gms /sqm) centre core and with mineral finish, laid on primed surface Fixed with hot molten bitumen of grade 85/25 @ 1.2 Kg / Sqm by forced applications as per manufacturers instructions with side over lap of 75 mm and end overlap of 100 mm. All overlap joints shall be sealed thoroughly by thermo fusing both the membrane layer (torching overlap by propane or butane gas torch) and sealing it with the help of hot trowel. The overlap joints shall be made as a monolithic layer.

Note:- 1. The work of water proofing treatment shall be got executed through authorised applicator of the manufacturer only and 10 year company back warranty to be submitted by contrcator. 2. The work is required to be carried out at accessible roof slab upto three storeyed. The contractor shall make arrangement of scaffolding, safety and security of workers . The rates quoted shall be deemed to be included for these items.

M&L for Cement concrete tiles 25cmx 25cmx 22mm thick machine pressed with grey cement and no pigments, set jointed and pointed in neat cement slurry in floor over 20 mm thick screed bed in cement mortar (1:4) over APP membrane.

S&F factory made single extruded WPC (Wood polymer Composite) pre-laminated both side Solid moulded Flush Door Shutter of 35 mm size comprising of virgin PVC resin of K value 58-60 (Suspension Grade), Calcium Carbonate and natural Fibers (Wood Powders/ rice husk/ wheat husk) and Non toxic additives (max toxicity index of 12 for 100 gms) having min density of 650 Kg/Cum and screw withdrawal strength of 1800 N (Face) &900 N (Edge) Minimum Compressive Strength of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of class A category with property of being Termite/ Borer proof. Water/ Moisture Proof, Fire retardant and fixing with stainless steel four Nos but hinges of 100 mm size on each shutter with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer - in- Charge, Materia test certificate and authentication should be compulsory provided by the manufacturing company.

S&F in repair for 35 mm thick factory made wiremess solid WPC (Wood polymer Composite) prelaminated on both side door shutter consisting of density 650 Kg / Cum manufactured by an ISO 9001-2015 certified company. Door to be paneled with SS mosquito mess and XTN aluminium mess for additional strength and safety purpose (confirming as per IS 4020). The door should be fixed to frame with 3 Nos SS (ISI marked) butt hinges size (100 x 25 x 2 ) mm and 32 mm long steel screw-drilled suitable to pass both the walls of MS tube. Other hardware should be fixed with (19 x 6) mmsize steel screw etc complete all as per directions of Engineer-in-Charge, manufacturer's specification Complete all as specified and directed.

S & F factory made WPC single extruded 100% lead free ROHS certified board of 18mm thick pre laminated shutter for kitchen, cupboards. The laminated shutter should be pre laminated side with different design and other side plain white of density not less than 600 kg / cum manufactured by an ISO 9001:2015 certified company. The 18mm board should be 100% lead free, water proof, termite proof and borer proof and should have good screw holding capacity and complete all as specified and directed.

S & F SS cabinet handles D type size 100 mm

Supply & fixing factory made single extruded WPC(Wood polymer composite) Solid door frame/ chowkat of size 100X50 comprising of virign PVC polymer of K value 58-60 (suspension grade ) calcium corbonate and natural fibers ( wood powder/rice husk /wheat husk) and non toxic additives (max toxicity index of 12 to 100 gms) fabricated with mitred joints and applying PVC solvent cement and screwed with full body threaded star headed SS screws having min frame density of750Kg/cum screw withdrawal strength of 2200 N (face) & 1100 N edge,minimum compressive strength of 58 N/mm2, moduus of elasticity 900N/mm2 and resistance to spread of flame of class 'A' category with property of being termite / borer proof, water / moisture proof & fire retardant & fixed in postion with SS dash fasterns / hold fast of required dia and length,colour of door frame to match that of shutter all as specified and directed.

Supply & fixing factory made single extruded WPC(Wood polymer composite) Solid door frame/ chowkat of size 65X125 comprising of virign PVC polymer of K value 58-60 (suspension grade ) calcium corbonate and natural fibers ( wood powder/rice husk /wheat husk) and non toxic additives (max toxicity index of 12 to 100 gms) fabricated with mitred joints and applying PVC solvent cement and screwed with full body threaded star headed SS screws having min frame density of750Kg/cum screw withdrawal strength of 2200 N (face) & 1100 N edge,minimum compressive strength of 58 N/mm2, moduus of elasticity 900N/mm2 and resistance to spread of flame of class 'A' category with property of being termite / borer proof, water / moisture proof & fire retardant & fixed in postion with SS dash fasterns / hold fast of required dia and length,colour of door frame to match that of shutter all as specified and directed.

S&F factory made single extruded WPC (Wood polymer Composite) Solid moulded Flush Door Shutter pre-laminated both side of 30 mm size comprising of virgin PVC resin of K value 58-60 (Suspension Grade), Calcium Carbonate and natural Fibers (Wood Powders/ rice husk/ wheat husk) and Non toxic additives (max toxicity index of 12 for 100 gms) having min density of 650 Kg/Cum and screw withdrawal strength of 1800 N (Face) &900 N (Edge) Minimum Compressive Strength of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of class A category with property of being Termite/ Borer proof. Water/ Moisture Proof, Fire retardant and fixing with stainless steel three Nos of butt hinges of 100 mm size on each shutter with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer - in- Charge, Materia test certificate and authentication should be compulsory provided by the manufacturing company.

S&F for mild steel window grills box type framed work as in window guard bars, grills or forged into spikes, framed balusters, walkway railing and similar work including welding, FE-290 grade E-165 complete all as specfied and directed.

S&F factory made steel windows (Box type) with side hung shutters precoated (colourcoated/ powder coated) with double shutters (glazed and gauged shutter bothn ) with frame complete all as specified and directed and shown on drg TD 158 sheet 1/2 & sheet 2/2 . NOTE :- Measurements shall be tken and paid compositly for frame, glazed and gauged. Grill shall be measured and paid seperately under respective item. No extra claim shall be entertained on this ground

S&F for steel ventilator (Box type) with side hung/top hung shutters precoated (colourcoated/ powder coated) with double shutters (glazed and gauged shutter both ) with frame complete all as specified and directed and shown on drg TD 158 sheet 1/2 & sheet 2/2 . NOTE :- Measurements shall be tken and paid compositly for frame, glazed and gauged. Grill shall be measured and paid seperately under respective item. No extra claim shall be entertained on this ground

Powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-Charge..

Providing and fixing factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware, EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured lor payment purpose.) Area not exceeding 2.00 Sqmn each.

S&F sheet glass ordinary quality 4mm thick and glazing with oil putty or fixed with bead/ glazing pins in squares n.exc. .5 sqm each pane all corner of glass to be fixed with silicon complete all as specified and directed.

S&F sheet glass ordinary quality 5.5mm thick and glazing with oil putty or fixed with bead/ glazing pins or fixed with silicon complete all as specified and directed.

S&F 4 mm thick Figured glass, pin head type and glazing with oil putty in squares n.exc 0.5 sq. m in each pane complete all as specified and directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with stainles steel wire stapel etc complete all as secified and as directed

S&F stainless steel tower bolt 200 mm long, complete all as specified and as directed

S&F stainless steel sliding door bolt size 300 mm with hasp, staple (bolt type). Complete all as specified and directed by Engr-In-charge.

S&F 150 mm long stainless steel handle,complete all as specified and as directed

S&F stainless steel double legged floor door stopper 150 mm long ,complete all as specified and as directed

S&F bal catches with 8 mm dia steel ball magnet catches for cuboard shutter including strking plate as approved etc complete all as specified and as directed

S&F mild steel helical door spring 300 mm long ordinary rat tail type incl roller and roller plate complete fixed with screws to wooden frames or with welding to steel frames complete all as specified and directed

S&F in repairs stainless steel decorative curtain rod of 25 mm bore incl necessary brackets, finial etc, complete all as specified and as directed

S & F stainless steel hydraulic concealed hinge with clip on installation and integrated Silent System, opening angle not less than 100º, For shutter thickness 15 - 24 mm full overlay type shutters, hinge cup dia 35 mm including necessary fixing arrangement with stainless steel screw complete all as specified & directed.

S & F for stainless steel glossy finish hat peg set of five tier with necessary fitting complete all as specified and directed.

S&F 500 litre rotational moulded tripple layer polyethlene water storage tanks white colour (cylindrical vertical with closed top) and suitable size of MS tasla with locking system hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed.

S&F 1000 litre rotational moulded tripple layer polyethlene water storage tanks white colour (cylindrical vertical with closed top) and suitable size of MS tasla with locking system hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed.

S&F 20mm ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed etc complete all as specified and as directed

S&F in repair Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe 20 mm bore and fixed as in repair complete all as specified and as directed

M & L for cutting chases, pinning in brick/PCC blocks wall in making good to facings where required and pointing in cement mortar 1:3 and cutting chases for concealed water tubing etc and making good complete all as specified and as directed

S&F medium grade galvanized steel tubing with all fittings &fixed complete to walls & ceiling or laid in floors 15 mm dia bore pipe (including in short length) complete all as specified and as directed

S&F tubes medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors 20 mm dia bore pipe (including in short length) complete all as specified and as directed

S&F in repairs vitreous chinaware white wash hand basin with pedestal of size 55X40 cm complete including fancy CP pillar tap, CP brass waste coupling ,waste pipe including fixing arrangement and cutting for and pinning in walls & making good complete all as specifed and directed.

S&F in repairs vitreous China corner wash hand basin, size as per manufacturer any design approved by GE including 15mm dia pillar tap, CP brass waste coupling, 450 mm long HDPE PVC connection, 750 mm long 32mm bore HDPE waste down pipe including CI brackets complete all as specified and directed.

S & F Brass CP wall mixer 15 mm bore (wall mounted type) for mixing hot and cold water screwed down for iron pipe and fixed complete all as specified and as directed

S&F Chromium plated brass Single lever hot & cold basin mixer with 450 mm braided connection pipe with out POP up complete all as directed.

S & F in repair fancy type 125mm size square brass CP shower rose with or without swivel joints complete all as specified and as directed.

S&F in repair bib tap long body fancy type cast copper alloy chromium plated with crutch or butterfly handle screwed down screwed for iron pipe or brass ferrule or fixed for 15 mm dia bore pipe complete all as specified and as directed

S&F in repair stop valves/angle valves fancy type chromium plated brass cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions fixed for 15 mm dia bore pipe complete all as specified and as directed

S&F in repair tubular towel rail 20mm dia type brass chrormium plated 600mm long between flanges complete all as specified and as directed

S&F in repair PVC connection of 45 cm length including brass nuts complete all as specified and as directed

S&F fancy type brass chromium plated soap dish of 160x160x90 mm complete all as specified and directed.

S&F fancy type glass corner 300mm radius of 10mm thick toughned glass with CP railing fixed with fancy type screws complete all as specified and directed.

S&F in repairs vitreous china squatting pan orissa pattern long pan size 580 mm x440mm white with spun pipe ‘P’ or ‘S’ trap, front or back inlet and foot rests excluding flushing cistern & flush pipe but incl. cement concrete bedding fixed complete all as specified and as directed

S&F in repair vitreous china wash down water closet pan (pedestal pattern) with 'P' or 'S' trap white, including seat cover, water jet and connection to drain or out going pipe and flush pipe anti symphonize pipes etc complete all as specified and directed.

S&F in repair PVC low level flushing cistern 10 litres, valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, flushing pipe complete all as specified and directed.

S&F Health faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1.25m long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

Supply and fixed CP 2- way Angle cock 15mm dia with wall flange.

S&F in repair Toilet paper holder with flat ressed type stainless steel complete all as specified and directed

S&F in repair for 75 mm bore out let cast iron floor trap spun pipe (conforming to IS 3989) incl cockroach trap with gratings including including jointing to waste pipe fixed in cement concrete tpe B-1 (1:2:4) etc complete all as specified and as directed

S&F in repair for 75 mm bore Cast iron spun pipe (conforming to IS 3989) soil, waste and vent pipes, in any length with or without ears with lead joints, laid in trenches or in floors or fixed to wall vertically complete all as specified and as directed

S&F in repair for 100 mm bore Cast iron spun pipe (conforming to IS 3989) soil, waste and vent pipes, in any length with or without ears with lead joints, laid in trenches or in floors or vertically cast, complete all as specified and as directed

S&F in repair 100 mm bore cast iron Bends of (any radius), spun pipe (conforming to IS 3989) diminishing piecs or tapers (larger bore measured) complete all as specified and as directed

S&F 75 mm bore cast iron spun pipe Branch pieces with oval access door Single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches (conforming to IS 3989) complete all as specified and as directed

S&F 100 mm bore cast iron spun pipe Branch pieces with oval access door Single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches (conforming to IS 3989) complete all as specified and as directed

S&F in repair 75 mm bore cast iron Branch pieces with oval access door Single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches (conforming to IS 3989) complete all as specified and as directed

S&F Salt-glazed stoneware gully traps, square or round mouthed, type 'P' with mouth size 150mm x 150mm setting and jointed to drains with cement mortar 1:1 including embedding in PCC (1:2:4) type B1 using 20 mm graded stone aggregate complete all as specified and as directed

S&F in repair 75 mm cast iron cowls spun pipe (conforming to IS 3989) complete all as specified and as directed

S&F in repair stainless steel sink with drainage board 1.00mm thick Gde 304 for kitchen with plug/waste pipe washers including cantiliver bracket or, connecting unions etc over all size 915 x 460mm with bowel size 410mm x 330mm x 160mm complete all as specified and as directed

S&F in repair stainless steel Gde 304 double bowl kitchen sink matt finish with plug/waste pipe washers including cantiliver bracket or, connecting unions etc over all size 1145 x 510mm with bowel size 532mm x 460mm x 225mm complete all as specified and as directed

S&F in repair kitchen plate rack stainless steel not less than 0.67 mm thick of size 90cm x 75cm complete fixed to brick/concrete wall, with screw including rawl plug complete all as specified and as directed

S&F in repair kitchen plate rack stainless steel 0.6 mm thick of size 76.2cm x 61cm complete fixed to brick/concrete wall, with screw including rawl plug complete all as specified and as directed

S&F in repairs for Stainless Steel (AISI 304 grade ) non magnetic multilayer nickel chrome plated for cutlery basket,with perforated bottom & side of compacted /slots for holding cutlery of size 510x470x100mm or 520x485x100 mm ( clear depth 500 mm). Complete all incl fixing of necessary telescopic channels, handels etc as required complete all as specified and as directed.

S&F for Stainless Steel (AISI 304 grade ) non magnetic multilayer nickel chrome plated for Plain basket of size 510x470x200mm or 520x485x200 mm or 486x500x200 mm .Complete all incl fixing of necessary telescopic channels, handels etc as required complete all as specified and as directed.

Excavation in post holes (or similar holes) each n exc 0.5 cum, getting out any type of soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50 m and making good surface

M&L for PCC 1:2:4 type B-2 using 20mm graded stone aggregates as in posts filling ,complete all as specified and directed by Engineer-in-Charge.

S&F MS joist channel (Fe 410-W Gde E-250 Quality A), angle or Tee section,MS tubes, flats square bars etc fixed indepently or framed or without connecting plates ,trusses etc any type framing including purlins and rafters etc confirming to Grade Fe 410-0 or Fe-310-0 complete all as specified and directed by Engr-in-Charge

S & F pre-painted galvalume aluminium zinc coating GI based corrugated steel 0.50 mm thick of any colour as directed by GE having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-Charge

S & F pre-painted galvalume aluminium zinc coating GI based plain steel 0.50 mm thick for ridge cover of any colour as directed by GE having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-Charge

M & L for (595 mm X 595mm) false ceiling system , using hot dipped galvanised steel section exposed surface with precoated capping, GI powerd coated tee and cross tee of size 24x32mm & 24x27mm having 0.27mm gauge at every 600mm c/c interval and wall angle of size 19x19mm having 0.35mm gauge fixed to the wall. The above grid is tobe suspended at every 1200mm c/c in both direction using 2mm thick pre-straightened GI wire laying designer tile ivory painted (high pressure steam cured) of 4 mm thickness (as per IS 14862) of size 595x595 mm and ant ine of the design (cascadev or electra) , back of the tile duly sanded and finished with a coat of protective paint over the formed grid etc complete all as specified and directed by Engineer-in-Charge.

S&F framed work as in doors or gates of angle or other section Fe 410 W Gde E 250 with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed.

S&F 1.25 mm thick mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete including cutting out of existing sheet if required complete all as specified and directed.

M&L for Preparation of new steel and iron surfaces of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer etc complete all as specified and as directed

M&L for Preparation of old steel and iron surfaces of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint etc complete all as specified and as directed

M&L for three coats of white wash on ceiling on new/old plastered surfaces including preparation of surfaces complete all as specified and as directed

M&L for complete removal of existing treatment by scrapping with mechanical wall sander (having mechanical vacum mechanism) having RPM not less than 1500 , sanding pad of 80 grit having dia 7" / 9" to make the surface free from dust loose paint etc from existing plastered surface by skilled labour complete all as directed by Engr-in-charge.

M&L for applying two coats of acrylic distemper using airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose lenth of 30 mtr. The spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface complete all as specified & directed.

Providing and applying external water proof cement based wall putty @ 1 Kg (undiluted) per sqm of average thickness 1 mm over plastered / old painted wall after scrapping to prepare the surface even and smooth complete and sanding of the putty surface with mechanical wall sander (having mechanical vacum mechanism) having RPM not less than 1500 , sanding pad of 240 grit or above to make the surface free fro dust etc. by skilled labour as per following steps :- Step 1 : Mix the putty powder by adding water as per manufacturer instructions and mix it with putty mixer with the mixing capacity of 2.50 Kg putty per minute. Step 2 : Apply the first coat of the prepared mix with the help of fully automatic airless spray machine of putty application having flow speed of max 6 Ltr per minute with a max pressure 3300 PSI. Step 3 : Allow 6 to 8 Hrs time to dry the putty surface.

Material & Labour for one coat of acrylic water based interior grade primer @ 0.80 Ltr (undiluted) / 10 Sqm diluted with water in 1:1 ratio to be applied with fully automatic airless spray machine of paint application with a flow speed of min 1 Ltr per minute having a pressure of 3300 PSI. Allow 6-8 hrs to dry the surface for painting of subsequent coats.

Material & Labour for two coat water based premium acrylic smooth exterier emulsion of approved colour with silicon additive & colour stay technlogy, excellent dirt pickup registance with low VOC less than 50 gm/litre as per the LEEDA specifications anti algal properties in two coats @ 1.79 Ltrs (undiluted) / 10 Sqm diluted with water as per manufacturer in instructions applied over one coat of acrylic water based exterier grade primer @ 0.90 Ltr (undiluted) / 10 Sqm diluted with water in 1:1 ratio, to be applied with fully automatic airless spray machine of paint application with a flow speed of min 1 Ltr per minute having a pressure of 3300 PSI. Allow 6-8 hrs to dry the surface for painting of subsequent coats. Complete all as specified and directed. Note: 1. For Item No 129 to 133 : (a) The work pertaining to periodical services & water proofing shall be executed from authorized applicator through manufacturer of which the material ie paint distemper, cement base paint Putty etc is proposed to be used by the contractor and approved by Garrison Engineer (b) The contractor shall upload the MOU with one of the manufacturer mentioned in the tender alongwith other documents under cover -1 failing which the bid shall be liable to be rejected.

M&L for brick work with sub class ‘B’ bricks straight or curved on plan in CM 1:4 as in half brick thick walls complete all as specified and as directed

Surface excavation n exc 30 cm deep and averaging 15 cm and getting out in any type of soil complete all as specified.

Excavation in trenches n.exc 1.5 m deep and n.exc 1.5 m wide in depth for foundation etc or for shaft wells, cesspits, manholes, peir holes etc. n exc.10 sqm on plan and n' exc 1.50 M depth and getting out in any type of soil for foundation etc complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in soil complete all as specified & directed.

Removing excavated materials (soil) n,exc 50 m and depositing where directed at a level n.exc 1.5 m above starting point complete all as specified and directed.

Spreading and levelling of soil obtained from excavation in layers n exc. 25 and well ramming including watering as required.

M&L for broken stone hard core n. exc 63mm, deposited, spread and levelled in layers n. exc 15 cm thick, watered and rammed to a true surface complete all as directed by Engineer- in- charge.

M&L for PCC (1:4:8) type D-2 using 40mm graded crushed stone aggregate as in foundation, filling, mass concrete etc complete all as specified and as directed.

M&L for providing plain cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregate) as in foundation and mass concrete complete all as specified and directed by Engr-In- Charge.

M&L for reinforced cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) (nominal mix) as in slabs supported on wall, landing, balconies, canopies, deck slabs and in shelves and like in repair to Chajjas, Claddings, soffits etc including bonding agent, complete all as specified and directed. Note:- Reinforcement to be measured & paid under respective items.

M&L for Treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area.

M&L for Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured).

M&L for Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface.

M&L for Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area.

M&L for Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall.

M&L for ATT Post construction treatment of soil under existing floor using emulsion as per manufacturer instruction @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floor complete all as specified.

M&L for Treating the soil along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping

M & L for form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide for rough finished surfaces of concrete complete all as specified and directed.

M & L for TMT Bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete incl welding etc (if reqd) all as specified and directed.

M&L for TMT Bars 6 to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete incl welding etc (if reqd) all as specified and directed.

Supply only liquid water proofing compound complete all as specified and directed.

S&F 15mm bore brass chromium plated sink mixer wall mounted typewith swivel spout 150 mm long, connecting legs & wall flange for mixing of Hot & cold water screwed down for iron pipe and fixed complete all as specified & directed.

Cutting openings through walls for door, window and other openings or enlarging existing openings, etc., or cutting out defective masonry for underpinning including providing, fixing and removing, shoring, cleaning and stacking stone and removing surplus to store and rubbish off the premises old masonry wall built in cement mortar, complete all as specified & directed.

Forming jambs, etc., to openings (to foregoing item), with stone supplied by MES including cutting, toothings and properly bonding into old work, including facing and pointing (if necessary) to match existing work, complete new work built in cement mortar (1:6) complete all as specified & directed.

Making good under cills (or over arches, lintels and bressummers) including all pinning as necessary new work built in cement mortar (1:6) complete all as specified & directed.

S&F stainless steel towel ring.

M&L for providing and fixing stainless steel (Grade-304) railing made of hollow tubes, channels, plates etc including welding, grinding, buffing, polishing and making curvature ( where ever required) and fitting the same with necessary stainless steel nuts and boltscomplete, including fixing the railing with necessary accessories & stailess steel dash fasteners, sstainless steel bolts etc, of required size, on the top of floor or the side of waist slab with suitable arrangement.

S&F aluminium extruded section body door clouser hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 kg and fixed complete all as specified & directed.

S&F brass matt finish Magic eye (Door viewer) with cover 180 degree for door thickness 35 mm to 55mm including screws and acessories.

M & L for cement concrete 1:3:6 type C-2 for 150 mm dia in concrete bed to drain pipes including packing under and haunching against the sides of pipes etc complete all as specified and directed.

M & L for reinforced concrete pipes, 150 mm dia class NP-2 laid and jointed complete with collars complete all as specified and directed.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1 : 4 mixed with water proofing compound finished even and smooth without using extra cement complete all as specified and directed by Engineer-In- Charge. (Water proofing compound shall be measure and paid seperatelly).

Cutting into existing manholes for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 or 3/4 section ) in cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate finished smooth and reforming benching as required for 150mm dia pipes complete all as specified and directed.

M&L for providing pre cast RCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in cover slab and man hole covers etc complete all as specified and directed by Engineer-In- Charge.

M & L for Construction of Septic Tank 50 users with brick masonry, PCC in foundation , floor, cover slab, including sludge chamber, CI vent pipe, CI cowl inlet and outlet pipe, RCC baffle wall and all necessary earthwork complete all as specified and directed. Ref. TD 217 sheet 1/7 to 7/7

M & L Soakage wells of size 3.00 m x 4.50 m complete all as shown on drawing and complete all as specified and directed. Ref. TD 309 sheet 1/4 to 4/4

M & L PCC 1:3:6 type C0 (using 12.5 mm graded stone aggragate) as in surface channel drain. Complete all as specified and directed

Extra for forming fair finished drain or channel, 30 cm inner girth in cement concrete using extra cement incl forms, moulds, mitred stopped ends etc complete all as specified and directed

M & L for Desludging / desilting of 150 mm dia sewage lines including manholes, up to 2.0 m depth by removing blockage if any by means of rodding manually or mechanically by pumping out water where required and removing residual silt / mud / peat / sludge out side of defence land complete all as directed. Note: Work of sewage disposal has to be carried under foul condition, hence the rate to be deemed included.Nothing extra shall be paid to the contractor on this account

M&L for brick work with sub class 'B' bricks old size bricks, straight or curved on plan exc. 6 m mean radius, built in CM (1:4) complete all as specified and directed.

M&L for 15mm thick rendering in cement mortar 1:4 on fair faces of brick masonry wall surfaces finished even and smooth without using extra cement complete all as specified and directed.

M & L applying two coats of cement based paint over a coat of primer on new plastered surface incl preparation of surfaces complete all as specified and directed by Engineer-in-Charge.

S & F mild steel angles, tees, flats, C section, MS square bars, MS Tubes etc as in steel gates, steel posts and struts in fencing, grills including embedding in concrete and screwing etc. including cut to shape as directed, drilling holes, notching for wire etc including all necessary drilling, bolting, welding or riveting and similar work conforming to FE-290 Gde E-165 complete all as specified and directed.

S & F 2mm thick fibre glass reinforced translucent corrugated / plain sheeting with two corrugated side lap fixed with coach screws and washers in roof, wall etc complete all as specified and directed.

Supply only PVC coated Chain link MS Galvanised fencing any size or type complete all as specified and directed by Engineer-in-Charge. Note :- Weight should be ascertained by the BOO.

Fixing only Chain link fencing including line wires,any mesh,size and type to any type of standard, rails, straining bolts, etc. including provision of binding wire complete all as specified and directed.

M&L for exterior grade, heavy duty tile 10-12 mm thick dark shade ( as approved by GE) square / rectangular size (400 x 400 ) mm, set, jointed and pointed in neat cement slurry with grey cement and pigment to match the shade / colour / matrix of tiles as in floor etc. including 15 mm thick cement screed bed in CM 1:6 etc complete all as specified and directed.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M&L for glossyfinish precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 grade, set and jointed in grey cement and pigment complete all as specified and directed.

Supply and laying in replacement pipe galvanized, “Medium class”, including fittings 40 mm dia all as specified and directed by Eng-in-charge.

Supply and laying in replacement pipe galvanized, “Medium class”, including fittings 25 mm dia all as specified and directed by Eng-in-charge.

Supply and fix in replacement Gun-metal, globe or gate valves confirmung to IS 9338 , 40 mm dia with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Supply and fix in replacement Gun-metal, globe or gate valves confirmung to IS 9338 , 25 mm dia with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

M&L for cutting cast iron/GI pipe up to 150 mm bore and reducing to required lenth before laying in position for insertion of new tees, branch, bends, Y junction including jointing materials complete all as specified and directed

M&L for construction of brick masonry valve pit of following internally size 600mm x 600mm x 600mm with angle iron 25mm x 25mm x 4mm frame and 2mm thick mild steel plate cover painted with two coats of synthetic enameled paint over a coat of red oxide primer after preparation of surface including locking arrangement, including necessary excavation and earth work 75 mm thick PCC 1:3:6 type C1 using 20mm graded stone aggregate over 100 mm thick hard core using broken in foundation/base floor, brick work in cement mortar (1:6) in one brick thick wall and 15mm thick cement plaster in cement mortar 1:4 on internal surface of walls and outside upto 150 mm deep below ground level complete all as specified and directed at site.

M&L for CI bends ( any type, radius & angle ) tapers any type, (straight), bends increasing or decreasing or double socket etc Tee pieces single branch, Y junction, double branch complete all as specified and directed

(a) One light point point /bell buzzer point controlled by one-one way switch.

(b) One ceiling fan/Exhaust fan point controlled by one-one way switch through Regulator.

(c) One three pin 5 Amp socket on same board with other switches.

(d) One three pin 5 Amp socket on independent board

(e) One light point controlled by two way switch

All as per item No 188 above but one 3 pin socket outlet 15 Amp independent, with cable 2.5 Sq mm size, with earth continuity coductor of size 2.5 Sq mm. compete all as specified and directed

All as per item No 188 above but for AC / Geyser point wiring ( one circuit for one point only) , with cable 4 Sq mm size, with earth continuity coductor of size 4 Sq mm. compete all as specified and directed

All as per iten no 188 above but for new point wiring of the following:-

(a) One light point point /bell buzzer point controlled by one,one way switch.

(b) One ceiling fan/Exhaust fan point controlled by one-one way switch through Regulator.

All as per item No 189 above but one 3 pin socket outlet 15 Amp independent, with cable 2.5 Sq mm size, with earth continuity coductor of size 2.5 Sq mm. compete all as specified and directed

All as per item No 189 above but for AC / Geyser point wiring ( one circuit for one point only), with cable 4 Sq mm size, with earth continuity coductor of size 4 Sq mm. compete all as specified and directed

S&F Modular switch 1 way 6A,1 Module SP 230 V AC complete all as specified & directed.

S&F Modular switch 1 way 16A,1 Module SP 230 V AC complete all as specified & directed.

S&F Modular switch 2way 6A,1 Module SP 230 V AC complete all as specified & directed.

S&F Modular Socket,6A-2/3 pin combined,2 Module 230 V AC complete all as specified & directed.

S&F Modular socket outlet two in one three pin 6/16 Amp flush type complete al as specified.

S&F Modular Bell switch 6 Amp,1 Module complete all as specified.

S & F ding dong bell AC 230 V single pole complete all as specified & directed.

S & F modular stepped type electronic fan regulator flush type two module suitable for 28 to 35 Watt BLDC ceiling fan complete all as specified & directed.

S & F ceiling rose, 3 terminal/PVC/polycarbonate, isolated body 250 V AC complete all as specified & directed.

S & F lamp holder PVC / polycarbonate type with back plate 230 V AC complete all as specified & directed.

Supply & fixing in replacement and Testing TP & N Vertical load line (VTPN) 4 way 415 Volts 50 Hz indoor type double door sheet metal enclosure IP-43 DB's IK-09 flush mounted with 250 Amp Copper busbar for each phase with two neutral bar & two earthbar and cable ties for cable management for Provision of MCCB as in comer including connecting terminal strip complete and SP MCBs as out going etc complete pre wired with suitable size copper conductor. The DB's shall hold type test certificate (CPRI) as per IEC 61439-3 complete all as specified and directed including taking out old unserviceable DB and removing from site. (Note :- DBs/MCCBs/ MCBs shall be of same make) MCCB and MCB are measured and paid seperately.

S & F in replacement sheet metal enclosures 240 volt with 100 amps rated copper bus bar for double door 8 way IP-43DB's lk-09 suitable for one MCB SPN as incoming and 6 MCB SP as out going, mounting flush on wall and making good disturbed surfaces complete all as specified and directed, including taking down old unserviceable DBs . (MCBs shall be measured and paid separately).

S & F MCB double pole 240 Volt 10 KA 40-63 Amp 'B' series conforming to ISI marked complete all as specified & directed .

S & F MCB single pole and 240 volt 10 KA 5-32 Amp 'B' series conforming to ISI marked all as specified and directed .

S & F MCCB 415 Volt 16 KA 4 pole 63 Amp magnetic trip release & setting as incoming with fixing arrangement complete all as specified and directed.

S & F MCCB 415 Volt 16 KA 4 pole 100 Amp magnetic trip release & setting as incoming with fixing arrangement complete all as specified and directed.

Supply & fix in replacement LED batten (4 ft) with aluminium extruded channel ( housing) and polycarbonate diffuser for glare free light with input power 20 watt, system efficiency not less than 100 lm / watt with built in surge protection not less than 2.0 KV with acessories like both side end cap, driver holder, screw including light fitting 1x20 W,220V AC decorative box type with driver ,holder including LED light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply & fix new LED batten (4 ft) with aluminium extruded channel ( housing) and polycarbonate diffuser for glare free light with input power 20 watt, system efficiency not less than 100 lm / watt with built in surge protection not less than 2.0 KV with acessories like both side end cap, driver holder, screw including light fitting 1x20 W,220V AC decorative box type with driver ,holder including LED light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S & F LED light fitting mirror type with aluminium ( housing) and polycarbonate diffuser 2 feet, 10 watt 220vV AC decorative type with acessories high out put diffuser 2 feet ,10 watt 220V AC decorative type like both side end cap, driver holder, screw including light fitting connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F Decorative, wall mounting, brushed nickel finish fixture with opal glass diffuser suitable with 10 W LED lamp B22 base with and including one No 10 watt LED bulb. complete with accessories and including connecting up with twin core twisted flexible copper conductor cable of suitable size. Make Havells/ Phillips/ Crompton

S & F in replacement of emergency LED 9 watt B-22 CDL Bulb Cool Day Light with lithium iron battery for 4-5 hours backup complete all as specified and directed.

S&F ceiling fans complete with blades, down rods and accessories, 230 V,1200mm sweep.Min air delivery 210 CMM with service value 6.00 BEE Five Star Rated with Brushless Direct Current(BLDC) Motor. Note: (1) Rate for taking down and trasportaion to deposit at E/M storeyard to ceiling fan deemed to be incuded in this rate.

Supply and fix electric water heater ,storage type ABS outer body with glass lined coated MS inner tank suitable to withstand 8 bar pressure and and heating element upto 2 KW capacity 25 litre,BEE 5 Star rated with led temp indicator and integrated shock safe plug complete with all accessories such as safety valve ,thermostate , NRV,connection pipe etc. complete all as specified and directed. Note-Old Unserviceable Geyser of any capacity will be deposited in E/M storeyard.

S&F sheet metal enclosure with 20 Amp modular socket, plug top and modular MCB SP 20 Amp 10 KA ( ready plug & play all in one device) complete all as specified and directed.

S&F exhaust fans complete with blades, frames & louvers etc with steel body AC single phase 230 Vof size 300 mm sweep and speed not less than 1400 RPM with double ball bearing, 100% copper winding motor all as specified by Engineer-in-Charge. Note Note:(1) Rate for taking down and trasportaion to deposit at E/M storeyard incl making hole of suitable size deemed to be incuded in this rate.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1400, Copper winding of sweep 250mm. Note:(1) Rate for taking down and trasportaion to deposit at E/M storeyard to exhaust fan incl making hole of suitable size deemed to be incuded in this rate.

M&L for earthing complete with using galvanized mild steel earth plate (electrode) 600 mm x 600 mmx 6 mm thick buried directly in ground, earth pit not less than 2.25 mtr deep below ground level with top edge of the earth plate not less than 1.50 m below ground level and earth plate surrounded with adequate quantity of charcoal dust mixed with salt to be packed thickness of 15 cm all round the plate using 4 mm dia GI earth lead wire as earth lead moulded and rivetted to earth plate at one end and connected to main equipment at switch/control board at another end, GI earth lead protected in and including 15 mm dia GI ‘medium grade’ pipe from upper end of earth plate upto equipment with & including 20 mm dia bore GI pipe ‘medium grade’ as water pipe from earth chamber to upper edge of the earth plate, GI funnel with wire mesh fixed on water pipe and provision of PCC 1:2:4 type B1(using 20 mm graded stone agg) as in pits chamber and RCC pit cover 50 mm thick of precast RCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as per electrical plate No.3 of SSR Part-II 2010 and testing on completion all as specified and directed.

Supply and Fixing in replacement Integral LED Street Light Luminaire comprising of high pressure die cast aluminum housing heat resistant toughened glass with frame IP-65 protection road way luminaries with high power LED 40/45 watt with efficiency 120 lumen/watt including GI brackete made out of 25 mm GI pipe medium grade and MS clamps for fixing of light fitting complete and connected with twin core PVC insulated copper flexible cable with existing point all as specified and directed

S&F in replacement of LED Bulkhead light fitting with aluminium housing and polycarbonate opal diffuser with power 10 watt, IP-65, system efficiency not less than 100lm / watt & built in surge protection not less than 2.0 KV with accessories connection up with three core flexible sheathed copper conductor cable of suitable size from ceiling rose complete all as directed.

S&F post top lantern LED type 40 watt 230 volts AC outdoor type made in die cast aluminium housing with decorative post top for 360 degree indirect light IP-65 protection with impact and corrosion resistant complete with driver and lamp complete.

M&L for cutting, chases, pinning in. making good to facings (For TV and Telephone Wiring) where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc. and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting not exc 10 cm girth.

S&F rigid non-metallic PVC conduit of 20mm external dia, exclusive of boxes (Junction/ terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing of accessories such as couplers, lock nuts, saddles, pipe hooks etc

S&F Junction box (1 to 4 way) compitable for 20 mm conduit complete all as specified and directed.

S&F of modular Telephone socket RJ11 complete with modular plate fitted on modular GI metal box of 1/2 module including frame of suitable size. (For ofrs Qtrs)

S&F of modular TV socket complete with modular plate including modular frame fitted on modular GI metal box of 1/2 module.

M&L for TV Wiring with Co axial RG-6 heavy duty PVC insulated, PVC sheathed cable having single strand of 0.7 mm dia taped in concealed PVC conduit suitable for television wiring including all necessary connections from terminal box to TV socket, drawn in separate concealed PVC conduit, complete all as specified and directed.

M&L for Telephone Wiring with 0.5 mm dia FRLS-H, 2 pair PVC insulated annealed copper conductor, unarmored telephone cable in the existing concealed PVC conduit suitable for television wiring including all necessary connections from terminal box to socket, drawn in separate concealed PVC conduit, complete all as specified and directed.

S&F of 4 way co axial cable splitter to distribute single cable TV into four output work on 5-2500 MHz frequency, complete all as specified and directed.

S&F of 2 way co axial cable splitter to distribute single cable TV into two output work on 5-2500 MHz frequency, complete all as specified and directed.

S&F of 10 pair telephone DP box made out of MS steel duily painted, complete all as specified and directed.

Supply and Fixing of electric chimney with autoclean function 750mmx500mmx550mm (width) dimensions having suction power of inlets 1300 Cum/hrs, motor warrany 3 years with power onsumption 180W, 230V, 50Htz having 3 speed gesture movement in black coated CRCA material and to be installed with proper aluminium pipe suitable size length as recommended by manufacturers from electric chimney to outside of bldg. complete all as specified and directed. Make : Hindware / Crompton / Faber

M&L for sheet metal board complete with locking arrangement, fabricated out of 2mm thick MS sheet of size 0.75 x 0.90 Mtr flushed in wall including mounting arrangements for energy meters and one MCB DB TPN 4 way, front opening, painting with two coats of synthetic enamel paint over a coat of red oxide primer on internal and external surfaces and making good damaged surface complete including taking down old unserviceable rusted sheet metal enclosure, from the building and all as specified and directed by Engineer-in-charge. Note:- 1. Meter Box for 06 Nos Energy Meters and 4-way TPN DB. 2. Energy Meter and TPN DB will be measured and paid seperately under relavent items.

M&L for vertical instant electric water heater with 3000 w power input & SS inner tank, capacity 3 Ltr complete with all accessories such as safety valve, thermostat, NRV, fixing bolts, stainless steel braided connection piece 450 mm long etc all as specified and directed by Engineer-in-charge.

Supplying, laying in replacement jointing and testing LT underground cable of size 16 sqmm 4 core heavy duty, 1100 volts PVC insulated and sheathed, armoured with multi stranded aluminium conductor cable confirmung to latest IS, laid in trenches / ducts or fixed to poles / walls or laid under roards / paths / drains / culverts duly protected in galvanised steel pipe of suitable sizes all bare conductor of cable duly insulated 1.1 KV grade heat shrinkable sleeve including cable gland and lugging etc at both ends all complete all as specified and directed. Note Excavation, earthwork, cable sand cushioning & cable protection shall be measured seperately under relevant items.

All as per Item No 235 above but of size 10 sqmm 2 core complete all as specified and directed.

M & L (in replacement) for GI tubing 'light grade with all necessary fittings laid in trenches / under road crossing / fixed on pole / wall / under floor including suitable mild steel FI clamps of required sizes complete for 50 mm bore.

M & L for boring holes (maunally) under road, hard standing without damaging surface for 50 mm dia GI pipe etc complete all as specified and directed.

M & L for laying local dry clean sand filling cushioning in trenches around under ground cable complete all as specified and directed. Note : - Total depth of the sand shall be 23 cm punned till 18 cm. Punned thickness will be measured.

M & L for laying well burnt brick, old size in trenches, as protection of underground cable complete all as specified and directed.

Note : Tenderers may note that amount of credit Rs 18,90,540.00 will be deducted from the total amount arrived, at the time of Acceptance of contract.

M/S SURAT SINGH AND SONS (BID ID -3291250)

M/s Arihant Builders (BID ID -3291153)

Pooja Singla Builders And Engineers Pvt Ltd (BID ID -3291142)

India Guniting Corporation (BID ID -3291278)

City Promoter and Buildwell Pvt. Ltd. (BID ID -3291311)

GEMINI PROMOTERS AND BUILDERS PVT. LTD. (BID ID -3290850)

M/s Chitter Mal & Co. (BID ID -3290719)

M/S RAJINDER SINGH (BID ID -3290213)

NARSINGH DEVELOPERS LLP (BID ID -3291323)

NITYA NAND AND SONS CONTRACTORS PVT LTD (BID ID -3291375)

AMIT ASSOCIATES (BID ID -3290723)