REPAIR MAINT OF INTERNAL EXTERNAL ELECTRIFICATION AND EXTERNAL WATER SUPPLY SYSTEM AT ALMORA UNDER GE RANIKHET

Amount

BOQ ( Sch A ) Internal Electric works Taking down carefully copper / aluminium point wiring (light, fan, socket or power) complete with fittings such as switches, ceiling roses, pendants, sockets, lamp holders, brackets, bulk head fittings, tube light fittings etc. and making good disturbed surfaces of walls etc. as per existing finishes by plastering, repairs and white / colour wash etc. complete all as specified and directed.

Supply and fixing point wiring for one light point / fan point / bell point (independent point), controlled by one, one way switch with 1.50 sqmm size PVC insulated unsheathed 1100 volts grade single core (multi-stranded) copper conductor cable (FRLS) drawn into and including medium grade PVC conduit concealed (not less than 20 mm dia) with all necessary fittings and accessories fixed concealed (including chase cutting in brick/stone/PCC block masonery wall for fixing conduit and plastering the external surfaces and matching the same with existing suface) and sunk cast iron or pressed steel terminal boxes for mounting fitting like switches, sockets, lamp holders, sketch fittings and covered with 3 mm thick plastic laminated bakelite sheet cover fixed with brass screws and cup washers including one continuous run of PVC insulated (green colour) 1.50 sqmm size multistranded copper conductor cable as in earth wire and connected to common earth dolly complete all as specified (Note:- wiring shall be in done in colour coding as directed by Engineer in charge )

All as per item No 2 above but one light point controlled by two 2- way switch

All as per item No 2 above but one socket outlet 5 pin 5 Amp controlled by one, one way switch on same board.

All as per item No 2 above but one socket outlet 5 pin 5 Amp controlled by one, one way switch on indipendent board..

All as per item No 2 above but wiring with using cable 2.50 sqmm size multistranded copper wire (FRLS) and earth wire of PVC insulated (Green colour) 1.50 Sqmm size multistranded copper wire for one 6 pin socket outlet, 15/16 Amp on independent board.

Supply & Fixing point wiring for one light point / fan point / bell point (independent point), controlled by one, one way switch with 1.50 sqmm size PVC insulated unsheathed 1100 volts grade single core (multi-stranded) copper conductor cable ( FRLS) drawn into and including PVC casing capping of suitable size with its all necessary fittings and accessories on wooden/stone/brick/PCC block masonry wall surface and sunk cast iron or pressed steel terminal boxes for mounting fitting like switches, sockets, lamp holders, sketch fittings and covered with 3 mm thick plastic laminated Bakelite sheet cover fixed with brass screws and cup washers including one continuous run of PVC insulated (green colour) 1.50 sqmm size multistranded copper conductor cable as in earth wire and connected to common earth dolly complete all as specified and directed, are as follows :- (Note:- wiring shall be in done in colour coding as directed by Engineer in charge )

All as per item No 7 above but One socket outlet 5 pin 5 Amp controlled by one, one way switch on same board.

All as per item No 7 above but one socket outlet 5 pin 5 Amp controlled by one, one way switch on independent board.

All as per item No. 7 above but wiring with using cable 2.50 sqmm size multistranded copper wire (FRLS) and earth wire of PVC insulated (Green colour) 1.50 Sqmm size multistranded copper wire for one 6 pin socket outlet, 15/16 Amp on independent board.

Supply and fixing switch piano flush type single pole one-way 5/6Amp complete all as specified and directed.

Supply and fixing switch piano flush type single pole Two way 5/6 Amp complete all as specified and directed.

Supply and fixing switch piano flush type single pole one-way 15/16 Amp complete all as specified and directed.

Supply and fixing socket outlet 5/6 Amp, 5 pin , flush type complete all as specified and directed.

Supply and fixing socket outlet 2-in-1, 3 pin 5/6 and 15/16 Amp flush type, complete all as specified and directed.

Supply and fixing ceiling rose, PVC / polycarbonate isolated body three terminal complete all as specified and directed.

Supply and fixing lamp holder, PVC / polycarbonate type insulated body with back plate suitable for batten / wall fittings complete all as specified and directed.

Supply and fixing High quality LED T8 indoor batten tube light 20 watt with aluminium extrusion in D shaped have large diametre for increased convection heat transfer including one LED PC tube rod and driver, internally pre wired of 1.5 sqmm twin twisted flexible cable complete all as specified & directed.

Supply & Fixing 240 V, 10 KA AC 'B' curve miniature circiut breaker ( MCB) of single poles and current carrying capacity 6 to 32 Amp in the MCB DB complete with connection testing and commissioning including taking down complete all as specified and directed.

Supply and fixing LED light fitting mirror type with high output diffuser 2 feet, 1x10 watt, 220 Volt AC, decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size & length, complete all as specified and directed

S & F in MCB SPN, 240 volts, 40 Amps to 63 Amps (Isolator), rupturing capacity 10 KA, ‘C’ curve type complete all as specified and directed.

S & F in repair MCB Four pole, 415 volts, 40 to 100 Ampere, rupturing capacity 10 KA, ‘B’ curve type complete all as specified and directed.

Supply & Fixing LED bulk head light fitting, 1x10/1x9 watt with PDC aluminium housing and milky diffuser with all accessories and including LED light driver holder, connecting up with three core twisted flexible copper conductor cable suitable size of 230 volts, 50 HZ complete all as specified and directed.

Supply and fixing in repair sheet metal enclosure for DB’s (Double door type) when MCB’s to be used, single pole and neutral, 8 ways with 200 Amp rated bus bar, 240 volts including blanking plates fixed sunk / flush to the wall or niche complete all as specified and directed.

S & F Recess mounting LED luminaire 600mm x 600 mm ,36 W, 220v, with high efficiency PMMA diffuser soft glare free light suitable for recessed mounting ,with powder coated CRCA housing with LEDs, seamless front frame complete with driver and all accessories internally pre-wired and including necessary cutting as required in panel and connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed.

Supply and fixing in repair sheet metal enclosure for DB’s (Double door type) when MCB’s to be used, triple pole and neutral, 4 ways with 200 Amp rated bus bar, 415 volts including blanking plate fixed sunk / flush to the wall or niche complete all as specified and directed.

Material & labour for sub main wiring with 1100 volt grade two single core PVC insulated and unsheathed cable with multistranded copper conductor 4 sqmm (FRLS) drawn into and including electrical grade PVC conduit not less than 25 mm dia with all accessories fixed concealed including chase cutting in brick/ stone/PCC block masonry for fixing conduit and making good the disturb surfaces of wall as per existing including 4 sqmm multi - stranded copper conductor as earth wire in green colour including taking down existing unserviceable sub main wiring complete all as specified and directed. NOTE: (Note :- 2 runs of 4 sqmm single cable, one run of 4 sqmm earth wire cable and PVC conduit shall be considered as one unit/1Rm)

Material & labour for sub main wiring with 1100 volt grade two single core PVC insulated and unsheathed cable with multistranded copper conductor 6 sqmm (FRLS) fixed in and including PVC conduit pipe 25 mm dia with all accessories and one continuous run of 4.0 Sqmm multistranded copper conductor PVC including taking down existing unserviceable sub main wiring complete all as specified and directed. NOTE: (Note :- 2 single core cables along with earth wire and concuit shall be measured as one unit length).

Material and Labour for replacing insulation deteriorated PVC insulated twin core flat 10 Sqmm, 1100 Volts grade heavy duty multistranded aluminium, conductor cable in service connection suspended by insulating hangers not more than 1 mtr apart including 4mm dia GI wire including taking down complete all as specified and as directed.

Material and labour for earthing complete with galvanised earth plate electrode 600 X 600 X 6 mm thick burried directly in ground (earth pit not less than 2.25 m below ground level) with top edge of earth plate not less than 1.5 m below normal ground level, connected to galvanised earth lead wire 4 mm dia by means of nuts, bolts, check nuts & washers of galvanised iron or steel all as shown on electrical plate No. 3 of MES schedule 2009, Part – I (Specifications) and connected to main switch board / main DB’s / earthing test point including all necessary excavation and earth work in any type of soil, adequate quantity of charcoal dust & common salt all around the earth plate minimum 150 mm in all directions with & including watering pipe 20 mm dia GI medium grade, GI funnel made out of 0.63 mm thick GI sheet, wire gauge, 50 mm thick RCC cover in PCC 1:2:4, type B-1 (using 20 mm graded crushed stone aggregate), duly reinforced with 6 mm dia mild steel round bars @ 150 mm both ways center to center with suitable lifting handle to cover, earth pit of PCC 1:3:6 type C-1 (using 20 mm graded stone aggregate), GI protection pipe light grade 15 mm bore up to 7.5 m length from earth electrode & engraving of earth marking on nearby building with CM 1:4 plate size 200 X 150 X 15 mm & painting of earth result etc. including testing on complete all as specified and directed Note: - On testing after completion of job, if desired earth resistance is not obtained, the earthing shall be redone by the contractor without any extra cost to Govt at his own expenses.

Supply and fixing of single phase call bell ‘DING DONG’, AC 230 volts single pole complete all as specified and directed.

Supply and fixing of bell push, piano flush type, single pole, one way 5 amps complete all as specified and directed.

Supply & Fixing Exhaust fan plastic body heavy duty ISI mark, 250 mm size with louvers including all connecting accessories including, cutting, opening through bricks/ stone/PCC block wall for fixing in openings , grounting of suitable size of nuts & bolts for exhaust fan and making good distrubed surface , connecting flexible cable wire from ceiling rose to exhaust fan complete all as specified and directed .

Supply and fixing in replacement High quality LED T8 tube rod 20 watt (with in build driber) with single sided connection including connection with wire of 1.5 Sqmm twin twisted flexible cable complete all as specified and directed.

Supply and fixing round shape 6 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fixing round shape 12 watt 220 volts AC surface type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fixing High quality LED T5 integrated batten tube light 20 watt with aluminium extrusion with frosted PMMA/PC diffuser, internally pre wired of 1.5 sqmm twin twisted flexible cable complete all as specified & directed.

Supply & Fixing LED post top lantern 40 watt with IP 65 protection comprises of Spherical/Diamond shape diffuser cover, etc and all accessories including monkey cage of suitable size for protection of light, light grade GI pipe of suitable length and wire required for connections etc complete all as directed. Make : Havells, Philips, Crompton, C&S.

Supply and fixing in repairs plug top 15/16 Amp, 3 Pin complete all as specified & directed.

Material and labour for supply, transporting, erecting truly in vertical position and fixing of steel tubular pole swaged, over all length 9 metres, type 410 – SP – 31 complete with mild steel base plate, pole cap, finial taper plug, MS bolts, nuts & washers, necessary excavation & earthwork in hard / dense soil, PCC sub base block as mass concrete of size 600 X 600 X 150 mm in cement concrete 1:4:8 Type D-2 in base of foundation, PCC foundation block of size 600 X 600 X 1500 mm in cement concrete 1:3:6 Type C-2, pole plinth of size 600 X 600 X 300 mm in cement concrete 1:2:4 Type B-1 including necessary form work as required at site and painting of pole with two coats of anti corrosive black bituminous paint through out internally and externally upto planting depth (embedded in concrete) and remaining portion of the pole painted two coats of aluminium paint over a coat of red oxide primer on complete exposed surface including painting of 05 Nos. bands / strips of 30 cm wide each with two coats of synthetic enamel paint (black & yellow) at a distance of 30 cm from plinth block upto 1500 mm height and marking / sign writing of pole number and feeders locations of pole with thick synthetic enamel paint (white) complete all as specified and directed.

Material and labour for stringing, stretching and strengthening of overhead conductor (ACSR) on existing LT steel tubular pole including binding and jointing the conductor with and including 14 SWG binding wire and following sizes ACSR conductors: - (a) 6/1 X 2.59 mm aluminium and 1 X 2.59 mm steel (Weasel) (b) 6/1 X 3.00 mm aluminium and 1 X 3.00 mm steel (Ferret)

Supply and fixing in repairs shackle type insulator, porcelain, vitreous, white, brown or green insulator of size 75 mm height and 90 mm dia for working pressure of 1100 volts, LT complete with galvanised mild steel strap of size 31 X 3 mm / flat iron 50 X 6 mm ‘D’ clamp or ‘U’ clamp of suitable size and holding clamp, washers, insulator bolts of 12 mm dia, washers and nuts complete all as specified and directed.

Supply and fixing in repair stay assembly comprising of GI stay bow 14mm dia, 40cm long, galvanised stay rod 16mm dia, 180cm long with threaded ends, GI nuts, bolts, washers, GI stay plate 23x23cmx6mm thick, 02 Nos of thimbles, MS clamps made out of 50x6mm flat iron and stay wire 7/3.15 SWG, stay clamp, loop insulator of size 65x95 mm clearance of hole 16mm complete including necessary excavation, earth work in hard dense soil and PCC 1:3:6 all as shown in electrical plate No. 01 of SSR-2009 part1 , complete all as specified and directed.

Material and labour for stringing, stretching and strengthening of GI wire 4mm dia on LT electric lines including binding, jointing etc complete all as specified and directed

Material and labour for earthing complete with galvanised earth plate electrode 600 X 600 X 6 mm thick burried directly in ground (earth pit not less than 2.25 m below ground level) with top edge of earth plate not less than 1.5 m below normal ground level, connected to galvanised earth strip 32 X 6 mm size by means of nuts, bolts, check nuts & washers of galvanised iron or steel all as shown on electrical plate No. 3 of MES schedule 2009, Part – I (Specifications) and connected to main switch board / main DB’s / earthing test point including all necessary excavation and earth work in any type of soil, adequate quantity of charcoal dust & common salt all around the earth plate minimum 150 mm in all directions with & including watering pipe 20 mm dia GI medium grade, GI funnel made out of 0.63 mm thick GI sheet, wire gauge, 50 mm thick RCC cover in PCC 1:2:4, type B-1 (using 20 mm graded crushed stone aggregate), duly reinforced with 6 mm dia mild steel round bars @ 150 mm both ways center to center with suitable lifting handle to cover, earth pit of PCC 1:3:6 type C-1 (using 20 mm graded stone aggregate), GI protection pipe light grade 40 mm bore up to 7.5 m length from earth electrode & engraving of earth marking on nearby building with CM 1:4 plate size 200 X 150 X 15 mm & painting of earth result etc. including testing on complete all as specified and directed. Note: - On testing after completion of job, if desired earth resistance is not obtained, the earthing shall be redone by the contractor without any extra cost to Govt at his own expenses.

Supply, laying, jointing and commissioning LT XLPE 1100 volts grade heavy duty cable PVC insulated, multistranded aluminium conductor served with inner sheathing of PVC tape, armoured with GI steel or tape and over all PVC sheathing laid in trenches, floor through pipes, in duct on pole and roads etc of size 95 Sqmm 3.5 core

All as per Srl item No 46 here-in-before but sectional area 50sqmm 3.5 core

All as per Srl item No 46 here-in-before but sectional area 25 sqmm 4 core

All as per Srl item No 46 here-in-before but sectional area 16 sqmm 4 core

All as per Srl item No 46 here-in-before but sectional area 16 sqmm 2 core

All as per Srl item No 46 here-in-before but sectional area 10 sqmm 2 core

Taking out unserviceable LT cable of any type and size from pole/wall/trenches by disconnecting electric connections for repair / replacement of cable complete all as specified and directed.

Excavation in trenches not exceeding 1.50M wide and not exceeding 1.5M depth for laying cable and getting out in hard/dense soil complete all as specified and directed.

Returning, filling in, trenches including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick in hard/dense soil complete all as specified and directed.

Removing surplus soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above starting point complete all as specified and directed..

Material and labour for sand cushioning with a layer of fine sand 8 cm thick before laying the cable and 15 cm after laying the cable in trenches to cover under ground cable complete all as specified and directed. Note :-Punned down thickness of sand shall be considered for measurement)

Material and labour for brick protection to cable using old size class 'B' bricks of size (230x115x75mm), laid flat, dry butt jointed, laid lengthwise perpendicular to the axis of cable complete all as specified and directed by Engineer-in-charge.

Supply & Fixing in replacement plastic (moulded polypropylene) line phase separator (for separating 05 Nos. of over head line conductors of length 1200 mm) with 25 mm fly nuts and clamps suitable for 1100 volts grade LT electric lines of any size fixed with over head electric lines complete all as specified and directed.

Supply and fixing / laying of galvanized iron pipe of 80 mm nominal bore light grade for cable protection, fixed to pole/ alongwall/ floor/ under road/ across the drain or nallaha etc with clamps nuts, bolts and washers complete all as specified and directed. Note : The cost of MS clamp, nut, bolt, washer and GI fittings etc shall deemed to be included in the unit rate quoted by contractor.

All as per Srl item No 59 here-in-before but 32mm nominal bore of pipe

All as per Srl item No 59 here-in-before but 25mm nominal bore of pipe

Dismantling / taking out of old LT steel tubular pole any type and any size from foundations including dismantling of concrete, MS clamps, nuts-bolts, earth wire, over head line conductors, insulators, guarding cradles and other accessories including necessary excavation and earth work in any type of soil complete all as specified and directed.

Dismantling of existing stay assembly any type / size from its stay rod, cutting stay rod (above ground portion) dismantling of MS clamps, nut-bolts, stay bow, loop insulators, stay wire etc. complete all as specified and directed.

Dismantling / taking out old ACSR conductor / copper conductor / GI earth wire any size from existing overhead lines including disconnection complete all as specified and directed.

Dismantling / taking out old unserviceable insulator of any size / type from existing electric LT lines complete all as specified and directed.

M&L for one coat of aluminium shade paint of approved quality including preparation of existing old painted surface of steel tubular poles LT complete including flat iron clamps, bracing, cross arms etc and numbering of poles with white synthetic enamel paint over a circular painted base and strip marking paint up to a height of 5 feet with black & yellow five bands with synthetic paint (strip of 1 feet height each) complete all as specified and directed.

Supply & Fixing in repairs MCCB of Cap 160 Amp, 4pole, 36 KA, with adjustable thermal release and earth fault protection, 415 volt grade including cutting and welding work for fixing of MCCB in existing panels any type and model complete all as specified and directed.

All as per item No 67 here in before but cap 200 Amp,36 KA

All as per item No 67 here in before but cap 630 Amp, 50 KA

Cutting/ trimming of tree branches of any width/ girth up to 1.0 mtr distance on both sides of HT/ LT over load lines including collection and depositing the retrieved timber at a place as directed by Engr-in-charge. Note :- (i) Each span have a distance 40mtr approximately (ii) All cutting branches of trees shall be thrown away/ burnt at approximate 200 to 500 mtr away as directed.

Material and labour for PCC 1:2:4 type B-1, (using 20mm graded crushed stone aggregate) as in coping of pole, floor including necessary form work where required and fair and even finish to the exposed surfaces all as specified & directed.

Supply and Fix Danger notice plate of 1.6mm thick mild steel sheet, vitreous enamelled white, with letters, figures and conventional skull and bones in signal red colour and fixed with M.S. clamps, bolts and nuts of approved size, for LT, 20x15cm size complete all as specified and directed.

Supply and fixing for LT lightining arresters for outdoor use, expulsion type complete with all fittings, 30 Kiloamp discharge capacity distribution class complete all as specified and directed.

Dismantling and taking down unserviceable cross arm, channels and angle section various sizes and shapes flat iron clamps, including nut bolts and washer and removing from site complete all as specified and directed.

Supply & fixing cross arms bracing supports clamps, flat iron strips and back plates fabrication from structural steel section incl nuts, bolts washer MS pipe of required size and thickness for extension of height of pole by welding incl bending or welding cold or hot drilling holes for bolt in any shape or size as indicated or directed and inclusive of one primer coat under two finishing coat of aluminum paint complete all as specified and directed.

S&F synthetic insulating mat near electric Installations of size 2m x lmX 3mm thick complete all as specified and directed.

All as per item No 76 above but of size 2m x lm x 2.5 mm thick.

Supply and fix aluminium lugs of size 150 sqmm complete all as specified and directed.

Supply and fix aluminium lugs of size 120 sqmm complete all as specified and directed.

Supply and fix aluminium lugs of size 95 sqmm complete all as specified and directed.

Supply and fix aluminium lugs of size 25 sqmm complete all as specified and directed.

Supply and fix Test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 Nos 8mm dia 25mm long hexagonal head screw complete all as specified and directed.

Supply and fix Copper strip 20 x 3.15mm with saddles and fixing screws etc. for roof conductors and down conductors above ground complete all as specified and directed.

Dismantling fencing wire mesh, any type and any size complete all as specified and directed.

Dismantling posts or struts (wood, steel or RCC) embeded in concrete any section, including taking out embeded portion and making good distrubed ground in complete all as specified and as directed.

Excavating post holes or similar holes, each not exceeding 0.5 Cum, getting out in soft/ loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance not exceeding 50 M and making good surface complete all as specified and directed.

M&L for MS work for Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embedding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 290, Gde E-165 complete all as specified and directed.

S & F Mild steel, flat iron etc , as in supports for stiffening of fencing, wall ties, hold fasts, clamps, plain angle cleats for securing purlins and similar small articles confirming to Fe 410-W 0r E- 250 quality 'A' complete all as specified and directed.

S&F 4 mm dia GI wire chain link fencing including line wires, 100 x 100 mm mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and directed.

M& L for PCC 1:2:4 type B1 (using 20mm graded stone aggregate) in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under reamed piles and mass concrete in Columns, pillars, piers, posts and struts complete all as specified and directed.

S & F Mild steel TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia, or securing with clips complete all as specified and directed.

M& L for preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

S&F Mild steel bolts of dia n exc 12mm purpose made, with hexagonal or square head one end and screwed the other, or screw both ends; each screwed end to be fitted with washers and one hexagonal or square nut, exc 30cm long including drilling hole in iron post complete all as specified and directed.

Taking down old unserviceable junction box and Supply and fixing Junction Box made up of High quality thermoplastic polycarbonate enclosure with IP 65 degree of protection, weather proof, corrosion proof, dust proof, insulted and shock proof, fire retardant non toxic material with internally embedded gasket with 10 Amp MCB and 4 nos terminal of size 200x160x98 mm of make Hensel or equivalent make of Sintex/ Universal complete all as specified and directed

Taking up or down existing rusted/unserviceable GI tubing of any grade including S&F GI water tubing medium grade 50 mm bore, galvanised with all GI fittings (such as bends,elbows, tees, conectors, short pieces, back nuts, unions, caps & plugs etc) laid in trenches/on surface including cutttting, threading and testing complete all as specified and directed.

All as per item No 95 above but 40 mm bore

All as per item No 95 above but 25 mm bore

All as per item No 95 above but 20 mm bore

All as per item No 95 above but 15 mm bore

Taking out old unserviceable gate valves for replacement including S&F of gun metal gate valve of 50 mm bore ISI marked class I with iron wheel head screwed both ends for iron pipe & fixed complete all as specified and directed.

All as per item No 100 above but 40mm bore

All as per item No 100 above but 25 mm bore

All as per item No 100 above but 20 mm bore

All as per item No 100 above but 15 mm bore

S & F 40mm bore GI union complete all as specified and directed.

S & F 25mm bore GI union complete all as specified and directed.

S & F 20mm bore GI union complete all as specified and directed.

S & F 15mm bore GI union complete all as specified and directed.

Taking out old unserviceable sluice valve for replacement including S & F new sluice valve of 100 mm size cast iron body flanged and drilled as per ISI 14846 (ISI Marked) specifications PN-1.6 with stainless nuts, bolts, washers & fibre/rubber gasket steel spindle including all accessories complete all as specified and directed.

All as per item No 109 above but 80 mm size

S&F Mild steel, plain, black sheet of 1.6 mm thick in hearths, covering to water tanks; water troughs; ducts; urinal troughs and funnels, valve pit etc. cut to size edges beaded if directed, holes punched; including round headed screws, clout nails or rivets and fixed to steel members, etc., with plain 40 mm lap joints or welded/ riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as required complete all as directed. (Note : One end should be properly hinged and another end should be with locking arrangement.)

Serviceing, Overhaluing, checking and Testing complete of DG Set 62.5 KVA at Pump House No - 2 as under:- a) Supply and replacement of Lub oil filter, Fuel filter primary and secondary, Hose bend & Hose pipe, Air filter. b) Draing out old lubricant oil from oil sump and supply and filling of fresh lubricant oil 20 W 40 grade. c)Draing out water from radiator of engine and cleaning the same with anti rusting solution and supply and filling of coolent. d) Checking and making necessary adjustment to drive belts, Speed governor and fuel injectors for smooth function of the engine. Make:- Kirloskar

M & L for painting with two coat of synthetic enamelled paint of approved shade over a coat of red oxide primer on external surfaces of motor and pumps after complete removal of existing paint and preparation of steel & iron surfaces including writing SM/MES Nos with paint etc. complete all as specified and as directed.

Cleaning of valve pit chambers, removing algae, silt, sludge accumulated at bottom of valve pit chambers up to the entire satisfaction of Engineer in Charge complete all as specified and as directed.

S & F Nut, bolts and washers off Size as per sample complete all as specified and as directed.

Supply and fixing in repairs Pressure gauge with isolating valve and siphon of 7 Kg x 4" dial complete all as specified and as directed.

Collecting samples of under ground sump water from Almora pump house for Bacteriological testing and complete Chemical testing for parameters as specified Note : The bacteriological and chemical testing of water shall be carried out in Govt authorised laboratory . The item cost includes collecting of samples of water from UG sump and Pump house site and charges of Govt authorised laboratory for carrying out testing of water sample shall be born by the contractor.

Material and labour for servicing of electrically driven centrifugal pump set 20 HP Motor - pump set) including greasing , cleaning and replacement of water body kit seal cup, screw ring retainer, bearing , greasing of motor, nut bolt etc. complete all as specified and directed

Demolition of existing unserviceable masonry valve pit including all accessories like angle iron frame, door fixed with MS sheet cover etc and M & L for construction of brick masonery valve pit of size610x610x610mm (internal dimensions) with brick work of sub class 'B' old size bricks built in cement morter 1:4 and 10mm thick rendering on internal and exposed external surface and including 40x40x6mm mild steel angle frame 3.15mm thick mild steel sheet cover in two Nos shutters with handle and locking arrangement and 1 Nos 50mm size 4 levers lock with key in duplicate make Navtal including painting steel and iron surfaces with two coats of black bituminous paint over a coat of red oxide primer complete all as specified, shown on drawing and as directed.

Demolition of existing unserviceable masonry valve pit including all accessories like angle iron frame, door fixed with MS sheet cover etc and M & L for construction of brick masonery valve pit of size 1050x1050x900mm (internal dimensions) with brick work of sub class 'B' old size bricks built in cement morter 1:4 and 10mm thick rendering on internal and exposed external surface and including 40x40x6mm mild steel angle frame 3.15mm thick mild steel sheet cover in two Nos shutters with handle and locking arrangement and 1 Nos 50mm size 4 levers lock with key in duplicate make Navtal including painting steel and iron surfaces with two coats of black bituminous paint over a coat of red oxide primer complete all as specified, shown on drawing and as directed.

M & L for Cleaning of complete UG sump tank capacity 50000 gallon and clear water tank 50000 gallon by carrying out following works all as specified and directed and specified by Engr-in-charge :- a) Dewatering of left out water from the tanks by pumping out existing contaminated water complete with diesel engine driven pump or manually. b) Taking out complete mud/dirt and depositing the same not exceeding a distance of 500mtrs from the well/ UG Sump . c) Cleaning the tank by washing the sides and floor of the tank using scrubbers. d) Washing the tank using bleaching powder solution, removing sludge and mass from all the surface taking out the same until a clean surface is obtained, applying two coats of lime wash on walls, e) Painting the date of cleaning at a prominent place complete all as specified and as directed by Engineer-in-Charge.

Complete cleaning & welding of pressed steel/iron water storage tank from inside of capacity 1,91000 Ltrs capacity PS tank located at Helipad Ground, extraction of all mud/sand/dust/Algee deposits making it free from algee growth by scrapping & washing all mud/sand/dust/Algee deposits making it free from algee growth by scrapping & washing with water & painting with one coat of black bitumeneous paint all the MS items fitted inside the tank to make corrosion free incl marking of tank capacity and date of cleaning etc complete all as specified & as directed.

All as per item No 122 above but 80,000 Ltrs capacity PS tank located at MES Office pump house

All as per item No 122 above but 45,000 Ltrs capacity PS tank located at Near Army school

All as per item No 122 above but 41000 Ltrs capacity PS tank located at Near Army school

All as per item No 122 above but 10000 Ltrs capacity PS tank located at Near Army school

Surface dressing n.exc 15 cm deep as in any type soil including taking out all sapling shrubs, brushwood, undergrowth, roots, and trees n. exc 30 cm girth all removing to a distance n.exc 100 m from starting point complete all as specified and directed by Engr-in-charge (The area is to be carried out in and around Almora power house near APS and other E/M installation complete all as specified and directed

Taking out old unserviceable water level indicator and supply and fixing FRP scale conventional / Mechanical water level indicator complete with float, wire, float guide pipe , bracket & pulley, counter weight, indicator pin, etc including all accessories all as specified and as directed

Taking down cement or cement lime plaster of any description on brick or stone or PCC block walls, etc. including racking out joints, hacking for key, scrubbing down with water etc.&removing rubbish to a disance not exc 250m Complete all as specified and directed.

M&L for 15mm rendering thick in CM (1:4) on fair faces of brick work/concrete surfaces finished even & smooth (without using extra cement), complete all as specified and directed.

M&L for applying two coats of white wash on wall surface , including preparation of new plastered surfaces complete all as specified and directed

M & L for applying two coats of snowcem (cement based paint) on external wall surfaces including preparation of old decorated plastered or unplastered surfaces complete all as specified and directed .

Supply and fixing in Replacement of fully automatic Satr Delta Starter for 40 HP 415 Volts 50 hz 3 phase complete all as specified and directed. (L&T MN 25 FASD Cat Part No SS94366 or eqivalent approved make in Havells/Legrand/Siemans).

Supply and fixing LED street light fitting 30/35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all asspecified and directed.

Supply & Fixing LED street light fitting 45 W pressure die cast aluminium IP66 roadway luminaire with operating range from 80V AC to 440 V AC with high power LED as light source and electronic driver make in Havells with Cat Part no. ELEKTRASL45WLED757SASYBOPC or its equivelent approved make in C&S, Bajaj, Philips, Wipro including GI bracket light grade 25/32/40 mm and provn of electric supply to fitting from source by means of PVC Sheathed multi-stranded aluminium conductor cable of 2 x 2.5 core complete all as specified and directed.

Supply and fixing on pole / wall Nature switch 02 EC with enclosure factory made suitable for 8 KW street light load single phase 240 volts and power contactor rating 40 Ampere with MCB 63 Ampere contactor and terminal block confirming to IEC – 60947 – 4 – 1 / IS – 13947 – 4 – 1 (Sensor alongwith pre-dawn switching off timer, 4 – 8 hours) infrared sensor based switch for intelligent outdoor street light control model No. SWADEEP – 02EC8kW1P, Make – KAKATIYA ENERGY SYSTEMS LTD or its equivalent approved make in Indo Asian/Legrand/ L & T complete with and including mounting bracket, cable glands, openable doors with lock complete all as specified and directed.

M/S BHATT ENTERPRISES

KRISHNA SAI ENTERPRISES

AJA BUILDERS

aditya construction

M/s JS Constructions