Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹73.8 LAccepted-AOC ARYASAMAJ BELONIA SOUTH TRIPURA PIN 799155 | BELONIA | SOUTH TRIPURA | TRIPURA | 799155 | ₹73.8 L | L1 | Accepted-AOC Awarded the work as lowest bidder has quoted his rate twenty seven point five one percent below. |
| 2 | L2₹88.0 LRejected-AOC | ₹88.0 L | L2 | Rejected-AOC Not awarded due to higher rate compare to lowest bidder |
| 3 | L3₹89.5 LRejected-AOC | ₹89.5 L | L3 | Rejected-AOC Not awarded due to higher rate compare to lowest bidder |
| 4 | L4₹1.0 CrRejected-AOC VILL SN PALLI BELONIA SOUTH TRIPURA PIN 799155 | BELONIA | SOUTH TRIPURA | TRIPURA | 799155 | ₹1.0 Cr | L4 | Rejected-AOC Not awarded due to higher rate compare to lowest bidder |
| 5 | L5₹1.1 CrRejected-AOC BC NAGAR BELONIA SOUTH TRIPURA PIN 799155 | BELONIA | SOUTH TRIPURA | TRIPURA | 799155 | ₹1.1 Cr | L5 | Rejected-AOC Not awarded due to higher rate compare to lowest bidder |
Tender Value
₹1.0 Cr
EMD Value
₹2.0 L
Closing Date
16 Feb 2026, 3:00 pmClosed
Executive Engineer
O/O. the Executive Engineer, PWD(RandB) Belonia Division, South Tripura
Patch metalling, Bituminous grouting, Carpeting and other allied works
2026_CEPWD_69973_1
66/NIT/SE-III/R/PWDRandB/25-26
Open Tender
Civil Works - Roads
180 days
Hrishyamukh R.D. Block area
Please refer Tender documents.
5 documents required · 5 mandatory
₹4,000
₹2.0 L
11 May 2026
6 Feb 2026
16 Feb 2026
6 Feb 2026
16 Feb 2026
6 Feb 2026
Maintenance of bituminous surface road Repair to pot holes by removal of failed material, trimming the sides to vertical and levelling the bottom, cleaning the same with compressed air or any appropriate method, filled with 75 mm B.M, after applying bitumen emulsion prime coat at the bottom and bitumen emulsion tack coat on sides and on bottom as per MoRD technical specification Clauses 1900, 502, 503 and 504.
WBM Grading 2 Providing, laying, spreading and compacting jhama brick aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing rolling with three wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming binding materials to fill up the interstices of coarse aggregate, watering and compacting to the required density Grading- 2 as per MoRD Technical Specification Clause 405
WBM Grading 3 Providing, laying, spreading and compacting jhama brick aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing rolling with three wheel roller 80-100 KN in stages to proper grade and camber, applying and brooming, binding materials to fill up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per MoRD Technical Specification Clause 405. I. By Manual Means
Prime Coat Low porosity Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70- 1.00 kg/sqm using mechanical means as per MoRD Technical Specification Clause 502.
Tack Coat Providing and applying tack coat with bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surface treated with primer & cleaned with Hydraulic broom as per MoRD Technical Specification Clause 503.
Tack coat using hot straight run bitumen of grade VG-30 on bituminous surface Providing and applying tack coat using hot straight run bitumen of grade VG-30, including heating the bitumen, spraying the bitumen, cleaning and preparing the existing road surface as per specifications: On bituminous surface @ 0.50 Kg/ Sqm.
20 mm thick Open-Graded Premix Carpet using Bituminous (Viscosity grade / modified bitumen) Binder Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using viscosity grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C or Type D as per MoRD Technical Specification Clause 508 Case - II: By Mechanical Means Bitumen of VG-30
Seal Coat Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A or Type B or Type C or Type D as per MoRD Technical Specification Clause 510. A. By Manual Means i) Case - IV : Type D (premix with fine sand) a) Bitumen of VG-30
Road side Pucca Drains Construction of road side pucca drain with M10 (1:3:6 with jhama brick aggregate) to specified lines, grades, levels and dimensions as per approved design and MoRD Technical Specification Clause 307, 1606. Excavated material to be used in embankment at site. (including centering, shuttering, etc. but excluding reinforcement) a) Trapezoidal drain (top clear width 600 mm, bottom clear width 300 mm and clear depth of 400 mm) i) In Ordinary Soil
Surface Drains Construction of unlined surface drains of average cross-sectional area 0.4 sqm in ordinary soil to specified lines, grades, levels and dimensions. Excavated material to be used in embankment with a lift upto 3 m and lead of 50 m (average lead 25 m) as per MoRD Technical Specification Clause 307. (i) Surface Drains in Ordinary Soil a) Manual Means
Maintenance of Earthen shoulder (Stripping of excess soil) Stripping excess soil from the shoulder surface to achieve the approved level and compacting with plate compactor at OMC as per drawing and MoRD technical specification Clause 1903.
Manufacturing & supplying of machine made 4 mm G.I wire crates chain link type size of cage 1500 mm x 600 mm x 450 mm having square mesh of 80 mm x 80 mm. including carrying to the work site as per direction of the Engineer-in-Charge (Weight of each cage shall not be less than 7.80 Kg).
Supplying and stacking mixed class brick bats (50% first class & 50% unclass) including carriage, loading & unloading at the site of work complete as per direction of the Engineer-in-Charge
Labour charge for filling/packing of mixed class brick bats in S.W.G PVC wire crates of size of 1500 mm x 600 mm x 450 mm fastening with SWG GI wire and placing in river bed/slope properly as per direction of the Engineer-in-Charge
Please Enable Macros to View BoQ information
stage.html
html • 0.05 MB
tech_eval.pdf
fin_eval.pdf
aoc.pdf
finance_71207.pdf
boq_comp_chart.xlsx
xlsx
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.04 MB
Tendernotice_1.pdf
PDF • 1.43 MB
BOQ_71207.xls
BOQ • 0.29 MB
DNIeT66.pdf
Tender Documents • 2.49 MB
Download all tender documents and submit your bid