Construction of Higher Secondary School (Plus 2 Arts Stream) under STAR at Govt. Up-Graded Higher School Bankuli in Kosagumuda Block in the District of Nabarangpur for the year 2024-25

Supplying all materials, labour, T&P and fitting and fixing Brass/CP fittings(Jaquar Make) of the following nominal bore with supply of all jointing materials etc. all complete as per specification and the direction of the E.I.C. 15mm dia CP Angle Stop Cock

Earth work excavation in foundation in Hard of soil including hard moorum, stoney earth mixed with boulders ( except sheet rocks and boulders requiring blasting) with all leads and lifts including rough dressing the bed and depositing the excavated earth at places away from work site with all leads and lifts including cost of all labour and T&P required for the work complete as per direction of the Engineer-in-charge. (GROUND FLOOR)

Earth work in foundation excavation in Hard soil within initial lead and lift including rough dressing the bed etc complete as per direction of the Engineer-in-charge.CC Road (Paver Block) Key wall. Approach road

Supplying, filling in foundation and plinth with sand in layers well watered and rammed including cost, conveyance, royalty of all the materials required for the work labour with T&P and cess etc. complete in all respect as per specification and direction of the Engineer-in-charge. (GROUND FLOOR)

Supplying, filling in foundation and plinth with sand in layers well watered and rammed including cost, conveyance, royalty of all the materials required for the work labour with T&P and cess etc. complete in all respect as per specification and direction of the Engineer-in-charge.CC Road (Paver Block) Key wall. Approach road

Cement Concrete (1:3:6) in foundation and floors using 4cm size black broken granite aggregates of approved quality and from approved quarry including hoisting, lowering and laying concrete in layers not exceding 15cm (6") thick to the required level ramming, watering, curing etc. complete including cost and conveyance royalty, taxes of all materials and labour with T&P required for the work etc. complete as per direction of the Engineer in charge. (GROUND FLOOR)

Cement Concrete (1:3:6) in foundation and floors using 4cm size black broken granite aggregates of approved quality and from approved quarry including hoisting, lowering and laying concrete in layers not exceding 15cm (6") thick to the required level ramming, watering, curing etc. complete including cost and conveyance royalty, taxes of all materials and labour with T&P required for the work etc. complete as per direction of the Engineer in charge. CC Road (Paver Block) Key wall. Approach road

Cement concrete (1:2:4) with 12mm. Size hard broken granite chips (Crusher broken) including all cost, conveyance , royality etc. complete. (GROUND FLOOR)

RCC work of M 25 grade with 20 mm and down grade black hard granite (Crusher broken) stone chips including hoisting and laying.Footing (GROUND FLOOR)

RCC work of M 25 grade with 20 mm and down grade black hard granite (Crusher broken) stone chips including hoisting and laying.Column up to Plinth beam Level (GROUND FLOOR)

RCC work of M 25 grade with 20 mm and down grade black hard granite (Crusher broken) stone chips including hoisting and laying.Plinth Beam (GROUND FLOOR)

RCC work of M 25 grade with 20 mm and down grade black hard granite (Crusher broken) stone chips including hoisting and laying.Column (GROUND FLOOR)

RCC work of M 25 grade with 20 mm and down grade black hard granite (Crusher broken) stone chips including hoisting and laying.Roof Beam (GROUND FLOOR)

RCC work of M 25 grade with 20 mm and down grade black hard granite (Crusher broken) stone chips including hoisting and laying.Lintel (GROUND FLOOR)

RCC work of M 25 grade with 20 mm and down grade black hard granite (Crusher broken) stone chips including hoisting and laying.Roof Slab (GROUND FLOOR)

RCC work of M 25 grade with 20 mm and down grade black hard granite (Crusher broken) stone chips including hoisting and laying.Stair Case (GROUND FLOOR)

RCC work of M 25 grade with 20 mm and down grade black hard granite (Crusher broken) stone chips including hoisting and laying.Chajjas (GROUND FLOOR)

RCC work of M 25 grade with 20 mm and down grade black hard granite (Crusher broken) stone chips including hoisting and laying. Column (TERRACE FLOOR)

RCC work of M 25 grade with 20 mm and down grade black hard granite (Crusher broken) stone chips including hoisting and laying. Roof Beam (TERRACE FLOOR)

RCC work of M 25 grade with 20 mm and down grade black hard granite (Crusher broken) stone chips including hoisting and laying. Roof Slab (TERRACE FLOOR)

Providing HYSD bars including cutting, bending, binding and tying the grills and placing in position including cost, conveyance and royalty of all materials and cost of all labour etc. complete (GROUND FLOOR)

Providing HYSD bars including cutting, bending, binding and tying the grills and placing in position including cost, conveyance and royalty of all materials and cost of all labour etc. complete. (TERRACE FLOOR)

Fly ash Brick masonary with C.M (1:6) in Foundation including cost ,conveyance, royalty & taxex of all materials, labour, T&P etc. complete including watering and curing for required period as per the direction of the Engineer in charge. (GROUND FLOOR)

Fly ash Brick masonary with C.M (1:6) in Superstructure including cost ,conveyance, royalty & taxex of all materials, labour, T&P etc. complete including watering and curing for required period as per the direction of the Engineer in charge. (GROUND FLOOR)

Fly ash Brick masonary with C.M (1:6) in Superstructure including cost ,conveyance, royalty & taxex of all materials, labour, T&P etc. complete including watering and curing for required period as per the direction of the Engineer in charge. (TERRACE FLOOR)

20mm th Cement plaster in C.M (1:4) including punning over walls, finished smooth including watering curing and scaffolding with cost, conveyance, royalty, taxes of all the (GROUND FLOOR)

Coal taring two coats including cost of coal tar and tar paper with all cost, conveyance, labour, T&P and cess etc. complete as per specifications and direction of the Engineer-in-charge (GROUND FLOOR)

12mm thick inside Plastering with cement mortar(1:6) including all cost and conveyance, royalty, taxes of all materials etc. complete as directed by the Engineer in Charge. (GROUND FLOOR)

12mm thick outside Plastering with cement mortar (1:6) including all cost and conveyance, royalty, taxes of all materials etc. complete as directed by the Engineer in Charge.(TERRACE FLOOR)

16mm thick outside Plastering with cement mortar (1:6) including all cost and conveyance, royalty, taxes of all materials etc. complete as directed by the Engineer in Charge. (GROUND FLOOR)

16mm thick inside Plastering with cement mortar(1:6) including all cost and conveyance, royalty, taxes of all materials etc. complete as directed by the Engineer in Charge.(TERRACE FLOOR)

Fixing vetrified tiles of 600 x 600mm in floors treads or steps and landing on 25mm thick bed of cement mortar 1:1 jointed with neat cement slury mixed with pigment to match the shades of the tiles including rubbing and polishing with cost carriage royalty of all materials etc. complete. (GROUND FLOOR)

Supplying, fitting and fixing of Vitrified tile (In dados / skirting) of premium grade having thickness 8mm to 10mm conforming to IS 13756 of size 60cm x 60cm plain (Ivory) in floors with application of polymer modified cement based water resistance adhesive bed of required thickness of 10 mm and filling joints with epoxy grout of approved quality including cost of all materials, labour, T&P, taxes etc. complete required for the work as per direction of the Engineer-in-charge. (GROUND FLOOR)

Providing and fixing Kadappa tiles (upto 0.10 Sqm.) in dados, skirtings and risers of steps on 12 mm thick cement plaster (1:3) jointed with neat cement slury mixed with pigment to match the shades of the tiles including rubbing and polishing complete including cost of precast tiles as directed by the Engineer-in-charge. (GROUND FLOOR)

Fixing chequred tiles in floors, treads and landings on 25mm thick bed of cement mortar (1:1) joined with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing including cost of tile. (GROUND FLOOR)

Finishing walls with weather seal coat (two coats) over a coat of cement primer to outer walls surface including cost and conveyance of all materials to site, and all labour charges complete as per direction of Engineer in Charge. (GROUND FLOOR)

Finishing walls with weather seal coat (two coats) over a coat of cement primer to outer walls surface including cost and conveyance of all materials to site, and all labour charges complete as per direction of Engineer in Charge.(TERRACE FLOOR)

Wall painting 2 coats with plastic emulsion paint of approved shade on new work to give an even shade including cost of paint. (GROUND FLOOR)

Wall painting 2 coats with plastic emulsion paint of approved shade on new work to give an even shade including cost of paint. (TERRACE FLOOR)

Finishing wall surface of wall with Acrylic Wall Putty (Water based) of approved make and finished smooth and even surface to receive painting including cost conveyance and royalties of all materials etc complete as per direction of the Engineer in Charge. (GROUND FLOOR)

Providing, fitting and fixing of 32 mm thick flush door shutter with approved quality of 30mm thick BWR block board pasted with 1mm thick sunmica on both side of approved design and quality including cost of all fittings and fixtures etc. Complete. (GROUND FLOOR)

Providing, fitting and fixing of WPC Door frame (100 x 75 mm) with approved quality including cost of all fittings and fixtures etc. complete. (GROUND FLOOR)

Providing & Fixing of M.S. Door & Window and window Grills including cost and conveyance of all materials to site, and all labour charges etc complet as per direction of E.I.C. (GROUND FLOOR)

Providing & Fixing of M.S. Door & Window and window Grills including cost and conveyance of all materials to site, and all labour charges etc complet as per direction of E.I.C.(TERRACE FLOOR)

Labour for fixing of M.S doors and windows shutters of approved design in proper position making good to the damges of walls of R.C.C or other structural etc. including mending or cutting sizes or grooves in chaukhats with cost, conveyance, taxes, T&P and cess etc. complete in all respect as per specification and direction of the Engineer-in-charge.(TERRACE FLOOR)

Supplying, fitting and fixing of two track UPVC sliding window of approved make with 6mm thick glass of approved quality complete with frame, shutters and all fitting and fixtures. (GROUND FLOOR)

Providing and fixing of Partly fixed, partly top hung and partly louvered windows of approved make to be fabricated from roll formed sections made of pre-painted steel (base steel as per IS-513 of 0.6 mm thick “D” quality, galvanized as per IS-277 with zinc of 120 Gm/Sq.mtr) with paint specification being with primer of 5-7 microns and finished paint with polyster paint (Black /Pearl white/ Chocolate Brown) of 12-16 microns alongwith the alkyd backer at the back of 5-7 microns and the sizes of outer frame being of 46x52 mm and with all vertical and horizontal mullions are of 46x70 mm and fixed beadings are of 18x25 mm. Section for internal top and bottom frames in the louvered areas should be 18 x 40 mm.Top hung shutter should be of 46 x 46 mm. Accessories / gaskets are to be used as per the manufacturer’s supply and specification like handle being made of high grade aluminium powder coated and with nylon receiver and gasket will be made of EPDM. All corner brackets are to be made of CRCA with zinc phosphating. The mullion caps and louvered-clips should be of glass filled nylon. The sections are to be cut to length ,mitre joined with corner bracket and frames are fixed to the concrete/masonry walls by means of self expanding screws and glass to be used of 5 mm reflective with all taxes complete. (GROUND FLOOR)

Painting two coats over wood and iron work with approved Enamel paint over a coat of priming including cost and conveyance of all materials to site and all labour charges complete as per direction of E.I.C. (GROUND FLOOR)

Supplying, fitting and fixing of stainless steel of 304 grade in hand railing using 50mm dia of 2mm thick circular pipe with Balustrade of size 32mm x 32mm @ 0.90mtr. C/C and stainless square pipe bracing of size 32mm x 32mm x 2mm in 3 rows in stair case as per approved design and specification, buffing, polishing etc. with cost conveyance, taxes of all materials labour, T&P etc. required for the complete in all respect.

2.5 cm. thick grading concrete (1:2:2) on roof slab with 6mm. size hard granite chips on new work. (GROUND FLOOR)

2.5 cm. thick grading concrete (1:2:2) on roof slab with 6mm. size hard granite chips on new work. (TERRACE FLOOR)

Providing and applying of pre contructional antitermite treatment by drilling 12 mm dia holes at distance of 30 cm @ junction wall & floors about 300 mm apart deep enough

to reach the soil below & chemical emulsion ( PREMISE,IMIDACHLOPRIED30.5SC OF BAYER MAKE mixed with 47.5 ltrs water) pumped these holes to soak the soil @ 1 Ltr solution of each hole as per manufactures specification & the holes should be pluged the filling materials including cost of all materials,labour,conveyance,T&P,all taxes and hire charges of machinaries as per direction of Engineer-in-charge. (GROUND FLOOR)

Painting two coats over wood and iron work with approved Enamel paint over a coat of priming including cost and conveyance of all materials to site and all labour charges complete as per direction of E.I.C.(TERRACE FLOOR)

Providing and fixing rain water down pipe with necessary bend shoes and heads including cost of 75mm dia earthen pipe, clamps and nails etc. with all cost, conveyance, taxes of all the materials required for the work with all labour, T&P and cess etc. complete in all respect as per specification and direction of the Engineer-in-charge. (TERRACE FLOOR)

Providing and laying of 80 mm thick factory made cement concrete interlocking paver block of M-30 grade and approved make, varity, colour and size made by Block making machine with strong vibratory compaction of approved design and shape laid in required colour and pattern over 50 mm thick compacted bed of course sand, filling the joints with fine sand etc. all complete include cost, conveyance, royality, taxes of all materials, labour T&P etc, complete as per direction of Engineer-in-Charge.CC Road (Paver Block). Approach road

EI Work Recessed wiring to light point with 1.5 sq.mm FR PVC insulatedsingle core multistrand copper conductor of ISI marked with 20 mm dia non-metalic PVC flexible conduit with 5Amp, 250 V piano type modular switch ISI marked and ceiling rose ISI marked mounted on MS box having front Modular base & cover of suitable size , MS box with 1 sq.mm FR PVC insulated single core multistrand copper conductor as earth wire including all accesories and connection as per direction of Engineer in Charge. ( Make of wire Finolex/ L&T / Anchor / Havels /HPL/ V Guard ) (Wiring) Group A

Recessed wiring to light point with 1.5 sq.mm FR PVC insulatedsingle core multistrand copper conductor of ISI marked with 20 mm dia non-metalic PVC flexible conduit with 5Amp, 250 V piano type modular switch ISI marked and ceiling rose ISI marked mounted on MS box having front Modular base & cover of suitable size , MS box with 1 sq.mm FR PVC insulated single core multistrand copper conductor as earth wire including all accesories and connection as per direction of Engineer in Charge. ( Make of wire Finolex/ L&T / Anchor / Havels /HPL/ V Guard ) (Wiring) Group B

Recessed wiring to light point with 1.5 sq.mm FR PVC insulatedsingle core multistrand copper conductor of ISI marked with 20 mm dia non-metalic PVC flexible conduit with 5Amp, 250 V piano type modular switch ISI marked and ceiling rose ISI marked mounted on MS box having front Modular base & cover of suitable size , MS box with 1 sq.mm FR PVC insulated single core multistrand copper conductor as earth wire including all accesories and connection as per direction of Engineer in Charge. ( Make of wire Finolex/ L&T / Anchor / Havels /HPL/ V Guard ) (Wiring) Group C

Recessed wiring to Fan Point in... (Wiring) Group B

Recessed wiring to Fan Point in... (Wiring) Group C

Recessed wiring to Exhaust Fan Point in….. (Wiring) Group B

S/F of Angle holder replacing Ceilling Rose (Wiring)

S/F of fan hook 'S' type made of 16 mm MS rod for fixing in the Existing RCC Roof.

S/F of extension board of 6 modular Metal box with modular base & cover in recess including providing and fixing of 2 nos of 3pin 5/6amp modular socket out let & 2 nos of 5/6 amp piano type modular switch, connection, painting etc as required. (Switch Boards)

S/F of computer board consisting of 3 nos of 5amp modular plug and modular switch & 1 no of Mini MCB complete with wiring on 12 modular M.S. box with modular cover. (Switch Boards)

S/F of 1 no of 5 pin 15/16 amp. Socket , 1 no of switch & 1 no of 15/16A top with modular mini MCB, in 6 modular box with cover with connection, painting etc as required for Inverter connection.(Switch Boards)

S/F of 18 SWG Modular metal box of following sizes (Nominal size) in recess with suitable size of Modular base & cover in front including cutting the wall and making good the same in case of recessed conduit as required. (Switch Boards) 4 Modular box with base & cover

S/F of 18 SWG Modular metal box of following sizes (Nominal size) in recess with suitable size of Modular base & cover in front including cutting the wall and making good the same in case of recessed conduit as required. (Switch Boards) 8 Modular box with base & cover

S/F of 18 SWG Modular metal box of following sizes (Nominal size) in recess with suitable size of Modular base & cover in front including cutting the wall and making good the same in case of recessed conduit as required. (Switch Boards) 12 Modular box with base & cover

Wiring for circuit / sub-main wiring along with earth wire with following sizes of PVC insulated single core multistrand copper conductor with ISI marked conforming to IS-694/1990 in 20mm dia non metalic heavy duty flexible conduit 1.6mm in recessed PVC conduit as required (Make of wire - Finolex/L&T/Anchor/Havels/V-guard) 2x1.5+1x1.5 (1.8.1)

Wiring for circuit / sub-main wiring along with earth wire with following sizes of PVC insulated single core multistrand copper conductor with ISI marked conforming to IS-694/1990 in 20mm dia non metalic heavy duty flexible conduit 1.6mm in recessed PVC conduit as required (Make of wire - Finolex/L&T/Anchor/Havels/V-guard) 2x2.5+1x1.5 (1.8.2)

Wiring for circuit / sub-main wiring along with earth wire with following sizes of PVC insulated single core multistrand copper conductor with ISI marked conforming to IS-694/1990 in 20mm dia non metalic heavy duty flexible conduit 1.6mm in recessed PVC conduit as required (Make of wire - Finolex/L&T/Anchor/Havels/V-guard) 4x6+2x2.5(1:8:10)

Wiring for circuit / sub-main wiring along with earth wire with following sizes of PVC insulated single core multistrand copper conductor with ISI marked conforming to IS-694/1990 in 20mm dia non metalic heavy duty flexible conduit 1.6mm in recessed PVC conduit as required (Make of wire - Finolex/L&T/Anchor/Havels/V-guard) Inverter wiring (1x2.5smm) Copper wire (1.19.11A)

S/F of 'B/C/D' series SP MCB of 5 - 32A amp rating (As per direction of engineer in charge) 240Volt for lighting and other loads in the existing MCB Distribution board ISI marked complete with connection, testing and commissioning etc. as required single pole (SP) (2.6.1) Circuit Breakers & BDB

S/F of 'C' series 4 Pole MCB of 63A amp rating (As per direction of engineer in charge) 440Volt for lighting and other loads in the existing MCB Distribution board ISI marked complete with connection, testing and commissioning etc. as required without MCB box.Circuit Breakers & BDB

S/F of 'B/C/D' series TPN MCB of 5 - 32A amp rating (As per direction of engineer in charge) 440Volt for lighting and other loads in the existing MCB Distribution board ISI marked complete with connection, testing and commissioning etc. as required without MCB box(2.6.4) Circuit Breakers & BDB

Supply, Installation testing & commissioning of Main Switches (IS13940 part 3/1993) of following coopacity on existing surface/wall mounting & complete with H.R.C fuse links, inter connections earthing etc as required as per direction of Engineer Incharge (Make-Seimens/HPL/Anchor/L&T /Havels/C&S/R. K.) Circuit Breakers & BDB.S/F of 4 way (4+12) TPN MCB DB Single door (2.5.1)

Earthing with G.I. Earth pipe 3 mtr Long 40mm dia ISI marked including accessories & providing masonary enclosure with cover plate having locking arrangement & watering pipe with charcoal & salt as required (3.2) Earthing

Supply & laying 6 SWG G.I. wire in recess for loop earthing as required (3.17) Earthing

Providing & fixing plain 16/0.2mm twin twisted flexible, FR PVC insulated copper cable in polythene sleeve or conduit

of suitable size on the floor/wall or side of the table/door etc as required.(1.31) Fittings

S/F of 300 Exhaust fan with all accessoriesand connections (Make Usha-Aero Clean Plus DBB/ Polycab-Fresh on DBB/ Cropmton-Trans Air12" reversible/ Havells-Ventil Air DS(HS)/ Anchor-Anmol Delus R/ Orient-Power Flow DBB) Fittings

S/F of 18-25 wt. LED single strip tube. Light fittingwith all accessories & connection (make Havels/HPL/Crompton/Polycab/PAC) Fittings

S/F of 1200mm A.C. Ceiling fan (1Star) with all accessories and connections with out fan regulator (Make:Usha-Striker One/Neo/Crompton- highspeed/Havells-Samrat ES/Anchor- Turbo Speed Star/Orient-Summer Breeze Pro/ Great White-ALDOUS/Pollycab-Vital HS) Fittings

Fixing /I.T.C. of stepped type Modular regulator (1.25a)

S/F of 20mm dia down rod with all accessories (1.39+1.41) Fittings

S/F of 30-35 wt. LED St. Light fitting with LED Electronic driver with all accessories & connection( Make- Crompton/Phillips/HPL/Polycab/Havells ) Fittings

S/F of 9w Watt LED Bulb (Fittings)

S/F of portico lamp. (Fittings)

Provision of 40mm dia HDPE pipe for laying & protection of cable (Fittings)

Provision of Armoured cable size 3 1/2 x 35sqmm (25) (Cables)

Laying of MV cable above 25sqmm to 120 sqmm in ground (5.1.2) (Cables)

Laying of MV cable above 25sqmm to 120 sqmm on surface (Horizontally)(5.5.2) (Cables)

S/M of end termination of LV/MV cable size 3 1/2 x50 sqmm (5.8.22) (Cables)

Supply of "U" clamp, Nail, Screw, Clips etc. (Cables)

Supply & fixing of 100 A TPN Panel board 1. 100A MCCB (Make- Legrand/Seimens/L&T/C&S/) & 100A kitkat & bus bar 2. 32 A TPN MCB (Make- Legrand/Seimens/L&T/C&S/)- 2nos 3. 32A DP MCB (Make- Legrand/Seimens/L&T/C&S/)- 5 nos 4. 100 A 4P Manual changeover (Make- Legrand/Seimens/L&T/C&S/)- 1nos 5. Digital Volt meter & Ameter three phase 6. All accesories & Connection (Rating & Danger borad)

Labour for drilling a perfectly vertical bore hole at specified dia for a specified depth below ground level through consolidated and unconsolidated rock with down the hole hammer drilling rigs or combination rigs as required to suit the site condition as per the direction of the Engineer-in-charge including use of own rigs with its accessories, tools and plants and consumables etc for lowering of 125 mm dia P.V.C/G.I/MS pipes for housing fitted socket and with or without well screen as per the necessity for soft, medium, hard and boulder formation (G.I/P.V.C/M.S casing pipes if required to prevent collapse of over burden is to be provided by the contractor including lowering and withdrawing after completion of the tubewell) Drilling of 125mm dia bore :-00 mtr to 30.00 mtr Drilling of 100 mm dia bore :- 31 mtr to 70 Mtr

Lowering of the following size G.I/P.V.C pipes with or without slotted pipes as per the necessary from ground level upto 30 mtrs depth and fitted and fixed up in perfectly vertical position including cutting and threading pipes and slotted pipe and supplying and fixing all jointing materials, tools and plants complete and keeping the top of the casing pipe threaded including plugging tubewell to prevent entry of foreign materials from above. Lowering of 125 mm dia PVC pipes :- 00mtr to 30.00 mtr

Lowering of the following size G.I/P.V.C pipes with or without slotted pipes as per the necessary from ground level upto 30 mtrs depth and fitted and fixed up in perfectly vertical position including cutting and threading pipes and slotted pipe and supplying and fixing all jointing materials, tools and plants complete and keeping the top of the casing pipe threaded including plugging tubewell to prevent entry of foreign materials from above. Lowering of 125 mm dia PVC pipes :- 00mtr to 30.00 mtr. Cost of 125 mm dia PVC pipes:-00 mtr to 30 mtr

Supplying and fitting & fixing of I.S.I make 1.00 H.P single phase Submersible Pump set to give discharge of 3000 ltr/hour at a head of 40 mtr etc all complete as direction of EIC.

Supplying and fitting & fixing of D.O.L starter for 1.0 H.P single phase Submersible Pump etc all complete as per direction of E.I.C

Supplying and fitting & fixing of suitable cable and connecting the pump and starter etc all complete as per direction of E.I.C

Supplying and fitting & fixing of Plastic rope, M.S well cover, M.S clamp, etc all complete as per direction of Engineer-in-charge.

Supplying and fitting & fixing of HDPE pipes and pipe fittings with C.P Nippling and lowering to bore well, making connection to pumpset & testing etc all complete as per specification and the direction of the E.I.C. 32 mm dia HDPE Pipe

Supplying all materials, labour, T&P and Fitting and Fixing of Rotational moulded polythene cylindrical vertical water storage tank conforming to 15701/1996 including cutting holes through the tank and fixing mild steel tubes and fittings and providing extra sockets and jamnuts, including hoisting upto a height of 5 mtr above G.Land placing the tank in required position including conveyance of all materials to work site, payment of royalty, taxes etc all complete as per P.H specification and direction of the E.I.C. 2000 lits capacity on the roof of GF

Supplying all materials, labour, T&P and construction of masonry staging with providing 1st class K.B. Brick work in C.M.(1:6) of 0.46mtr height in staging, 12 mm cement plaster in C.M (1:6), R.C.C. Beam of 0.25mx0.30mx2.60m & roof slab of 1.40mx1.40m in C.C (1:1.5:3) using 12mm size H.G.Chips including centering, shuttering, bending and binding of rod etc watering, curring, conveyance of all materials to work site, payment of royalty, taxes etc all complete as per P.H specification and direction of the E.I.C. 2000 lits capacity on the roof of GF

Supplying all materials, labour, T&P and constructing Inspection Chamber of the following sizes with cement concrete (1:3:6) using 40 mm size HG metal on bed, 1st class KB Brick work in CM (1:6) moulding and shaping the channel inside and benching with C:C (1:1.5:3) using 12 mm size H.G chips, 12 mm thick cement plaster (1:3) with punning to inside, cement flush pointing (1:3) to outside, RCC cover slab in C.C(1:1.5:3) using 12 mm size H.G chips with RCC man hole cover, etc. all complete as per approved specification and direction of E.I.C Inside size 760mm x 760mm x 460mm

Supplying all materials, labour, T&P and constructing Gully Trap chamber of the following inside size with 8 cm thick precast cover slab in CC (1:2:4) mix using 12 mm size H.G chips, foundation concrete (1:4:8) using 40 mm size HG metal on bed and around trap , !st class KB Brick work in CM (1:6) in F & P and inside 12 mm thick cement plaster (1:3) finished with a floating coat of neat cement including fixing 100mmx100mm size HCI gully trap 150mmx150mm size C.I grating etc. all completed as per approved drawing, specification and direction of E.I.C.

Supplying all materials, labour, T&P and constructing soakway pit of the following size with dry brick walling from bottom upto invert of inlet pipe and 1st class KB brick work in CM (1:6) for the remaining height at top, 12mm thick Cement Plaster (1:4) inside and outside over masonry brick work, gravel packing in the rear of well steining, RCC cover slab in CC (1:1.5:3) using 12mm HG chips, fitted with iron lifting handles. etc all complete as per approved specification and direct

ion of the E.I.C. 0.90 m diax 2.0 m deep soakway pit

Supplying all materials, labour, T&P and constructing soakway pit of the following size with dry brick walling from bottom upto invert of inlet pipe and 1st class KB brick work in CM (1:6) for the remaining height at top, 12mm thick Cement Plaster (1:4) inside and outside over masonry brick work, gravel packing in the rear of well steining, RCC cover slab in CC (1:1.5:3) using 12mm HG chips, fitted with iron lifting handles. etc all complete as per approved specification and direction of the E.I.C. 0.90 m diax 2.0 m deep soakway pit. 1.20 m diax 2.0 m deep soakway pit

Supplying all materials, labour, T&P and laying in trenches U-PVC SWR/4Kg/cm2 soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No 13592/1992 including jointing with supply of approved rubber lubricant by non-heat application method/as per manufacturer's specification, testing, earthwork in excavation in all kinds of soil and providing bed concrete in P:C:C (1:4:8) using 40 mm size metal and haunch top the pipe with refilling of trenches etc all complete as per P.H specification and direction of the E.I.C.110mm Hunch Top

Supplying all materials, labour, T&P and laying in trenches U-PVC SWR/4Kg/cm2 soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No 13592/1992 including jointing with supply of approved rubber lubricant by non-heat application method/as per manufacturer's specification, testing, earthwork in excavation in all kinds of soil and providing bed concrete in P:C:C (1:4:8) using 40 mm size metal and haunch top the pipe with refilling of trenches etc all complete as per P.H specification and direction of the E.I.C.160mm PVc Pipe all round Hunch top

Earthwork in all kinds of soil in excavation of foundation trenches within 50m initial lead and 1.5m initial lift including rough dressing and breaking clods to maximum 5cm to 7cm and laying in layers not exceeding 0.30m in depth etc all complete as per direction of the E.I.C. Initial lift upto 1.5 mtr. 4.37 m x 3.18 m x 1.50 m

Earthwork in all kinds of soil in excavation of foundation trenches within 50m initial lead and 1.5m initial lift including rough dressing and breaking clods to maximum 5cm to 7cm and laying in layers not exceeding 0.30m in depth etc all complete as per direction of the E.I.C. From 1.5 mtr to 3.0 mtr depth. 4.37 m x 3.18 m x 0.70 m

Supplying all materials, labour, T&P and filling in foundation and plinth with river sand well watered and rammed including conveyance of all materials to work site, payment of royalty, taxes etc all complete as per the direction of the E.I.C.4.37 m x 3.18 m x 0.15 m

Supplying all materials, labour, T&P and providing cement concrete (1:3:6) with 40mm H.G metal including watering, curing and conveyance of all materials to site payment of royalty, taxes etc all complete as per P.H specification and direction of the E.I.C.4.37 m x 3.18 m x 0.10 m

Supplying all materials, labour, T&P and providing plain cement concrete (1:1.5:3) with 12mm size H.G chips including watering, curing and conveyance of all materials to work site, payment of royalty, taxes etc all complete as per P.H specification and direction of the E.I.C. 4.37 m x 3.18 m x 0.10 m =1.389 Cum 3.07 m x 1.88 m x 0.038 m = 0.219 Cum

Supplying all materials,labour, T&P and providing Brick work with K.B.Brick having crushing strength not less than 75 Kg/CM2 with dimensional tolerence of +/- 8% in C.M including watering, curring, conveyance of all materials to work site, payment of royalty, taxes etc all complete as per P.H specification and direction of the E.I.C. In Foundation and Plinth in C:M (1:4) 2 x ( 4.07 + 1.88 ) m x 0.50 m x 1.10 m = 6.545 cum 2 x ( 3.82 + 1.88 ) m x 0.375 m x 0.80 m = 3.420 cum

Supplying all materials, labour, T&P and providing cement plaster on brick/stone work including watering,curring and conveyance of all materials to work site, payment of royalty, taxes etc all complete as per P.H specification and direction of the E.I.C. 12 mm thick C.P in C:M (1:3) 2 x ( 3.07 + 1.88 ) m x 1.90 m =18.81sqm 3.07 x 1.88 m = 5.771 sqm

Supplying all materials, labour, T&P and providing cement punning on plastered surface including watering,curring and conveyance of all materials to work site, payment of royalty, taxes etc all complete as per P.H specification and direction of the E.I.C.Same as above item 20mm C.P in 1:3

Supplying all materials, labour, T&P and providing rigid and smooth centering and shuttering for RCC work including false work and dismantling them after casting including conveyance of all materials to work site, payment of royalty, taxes etc all complete as per P.H specification and direction of the Engineer-in-charge. 2 x (3.82 + 2.63 ) m x 0.125 m =1.612 sqm 3.07 m x 1.88 m = 5.771 sqm

Supplying all materials, labour, T&P and providing M.S.reinforcements for RCC work including cutting, bending, binding, straightening and tying the grills and placing in position including cost of binding wire 18 to 20 gauge conveyance of all materials to work site, payment of royalty, taxes etc all complete as per P.H specification and direction of the Engineer-in-charge.

Supplying all materials, labour, T&P and providing Reinforced cement concrete (1:1.5:3) with 12mm size H.G chips including watering, curing and conveyance of all materials to work site, payment of royalty, taxes etc all complete as per P.H specification and direction of the E.I.C. 3.82 m x 2.63 m x 0.125 m

Supplying all materials, labour,T&P and providing 12mm thick cement flush pointing in C:M (1:3) to Brick Masonry works including watering curring and conveyance of all materials to work site, payment of royalty, taxes etc all complete as per P.H specification and direction of the Engineer-in-charge. 2 x ( 4.07 + 2.88 ) m x 1.10 m = 15.29 Sqm 2 x ( 3.82 + 2.63 ) m x 0.80 m = 10.32 Sqm 2 x ( 4.07 + 2.63 ) m x 0.125 m = 1.675 Sqm

Supplying all materials, labour,T&P and filling Foundation and Plinth with excavated earth including watering, ramming etc all complete as per direction of the E.I.C.

SanitaryInstalation/Supplying all materials, labour, T&P and fitting and fixing U-PVC SWR soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No 13592/1992 to walls with nails, bobbins and wooden plugs including jointing with supply of approved rubber lubricant by non-heat application method/as per manufacturer's specification, testing etc all complete as per P.H specification and direction of the E.I.C. 110mm diameter U-PVC SWR pipes

SanitaryInstalation/Supplying all materials, labour, T&P and fitting and fixing U-PVC SWR soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No 13592/1992 to walls with nails, bobbins and wooden plugs including jointing with supply of approved rubber lubricant by non-heat application method/as per manufacturer's specification, testing etc all complete as per P.H specification and direction of the E.I.C. 110mm U-PVC SWR P-trap

SanitaryInstalation/Supplying all materials, labour, T&P and fitting and fixing U-PVC SWR soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No 13592/1992 to walls with nails, bobbins and wooden plugs including jointing with supply of approved rubber lubricant by non-heat application method/as per manufacturer's specification, testing etc all complete as per P.H specification and direction of the E.I.C. 110mm U-PVC SWR Single junction door

SanitaryInstalation/Supplying all materials, labour, T&P and fitting and fixing U-PVC SWR soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No 13592/1992 to walls with nails, bobbins and wooden plugs including jointing with supply of approved rubber lubricant by non-heat application method/as per manufacturer's specification, testing etc all complete as per P.H specification and direction of the E.I.C. 110mm U-PVC SWR door bend

SanitaryInstalation/Supplying all materials, labour, T&P and fitting and f

ixing U-PVC SWR soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No 13592/1992 to walls with nails, bobbins and wooden plugs including jointing with supply of approved rubber lubricant by non-heat application method/as per manufacturer's specification, testing etc all complete as per P.H specification and direction of the E.I.C. 110mm U-PVC SWR Offset

SanitaryInstalation/Supplying all materials, labour, T&P and fitting and fixing U-PVC SWR soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No 13592/1992 to walls with nails, bobbins and wooden plugs including jointing with supply of approved rubber lubricant by non-heat application method/as per manufacturer's specification, testing etc all complete as per P.H specification and direction of the E.I.C. 110mm U-PVC SWR plain bend

SanitaryInstalation/Supplying all materials, labour, T&P and fitting and fixing U-PVC SWR soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No 13592/1992 to walls with nails, bobbins and wooden plugs including jointing with supply of approved rubber lubricant by non-heat application method/as per manufacturer's specification, testing etc all complete as per P.H specification and direction of the E.I.C. 110mm U-PVC SWR vent cowl

SanitaryInstalation/Supplying all materials, labour, T&P and fitting and fixing U-PVC SWR soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No 13592/1992 to walls with nails, bobbins and wooden plugs including jointing with supply of approved rubber lubricant by non-heat application method/as per manufacturer's specification, testing etc all complete as per P.H specification and direction of the E.I.C. 75 mm diameter U-PVC SWR pipes

SanitaryInstalation/Supplying all materials, labour, T&P and fitting and fixing U-PVC SWR soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No 13592/1992 to walls with nails, bobbins and wooden plugs including jointing with supply of approved rubber lubricant by non-heat application method/as per manufacturer's specification, testing etc all complete as per P.H specification and direction of the E.I.C.75 mm U-PVC SWR plain bend.

SanitaryInstalation/Supplying all materials, labour, T&P and fitting and fixing U-PVC SWR soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No 13592/1992 to walls with nails, bobbins and wooden plugs including jointing with supply of approved rubber lubricant by non-heat application method/as per manufacturer's specification, testing etc all complete as per P.H specification and direction of the E.I.C.125 mm dia C.P Grating

Internal PH Works Supplying all materials, labour, T&P and providing and fixing to wall or ceiling or floor G.I./PVC pipes and pipe fittings of the following nominal bore with clamps including making good the wall, ceiling,and floor, testing all complete as per specification and the direction of the E.I.C. 20mm dia CPVC pipes Internal

Supplying all materials, labour, T&P and providing and fixing to wall or ceiling or floor G.I./PVC pipes and pipe fittings of the following nominal bore with clamps including making good the wall, ceiling,and floor, testing all complete as per specification and the direction of the E.I.C. 25mm dia CPVC pipes External

supplying all materials, labour, T&P and cutting holes through existing brick/stone masonry walls for taking GI/PVC pipes and fittings including making good the damages in cement mortar (1:4) etc. all complete as per P.H. specification and direction of E.I.C. R.C.C Roof/Chaja

supplying all materials, labour, T&P and cutting holes through existing brick/stone masonry walls for taking GI/PVC pipes and fittings including making good the damages in cement mortar (1:4) etc. all complete as per P.H. specification and direction of E.I.C.R.C.C oof/Chaja Cutting Groove in wall or floor

supplying all materials, labour, T&P and cutting holes through existing brick/stone masonry walls for taking GI/PVC pipes and fittings including making good the damages in cement mortar (1:4) etc. all complete as per P.H. specification and direction of E.I.C.R.C.C oof/Chaja Cutting hole(250 mm wall)

supplying all materials, labour, T&P and cutting holes through existing brick/stone masonry walls for taking GI/PVC pipes and fittings including making good the damages in cement mortar (1:4) etc. all complete as per P.H. specification and direction of E.I.C.R.C.C oof/Chaja Cutting hole(375 mm wall)

Supplying all materials, labour, T&P and fixing porcelain glazed tiles in floors, on 25mm thick bed of cement mortar 1:1 joined with neat cement slurry mixed with pigment to match the shades of the tiles including rubbing and polishing etc. all complete as per specification and direction of the E.I.C. Ground Floor. 2nosx7.0x2.4m=34.00 Sqm

Supplying all materials, labour, T&P and fixing porcelain glazed tiles in dados/skirtings on 12mm thick cement plaster (1:3) joined with neat cement slurry mixed with pigments to match the shades of the tiles including rubbing and polishing etc. all complete as per direction of the E.I.C. Ground Floor. 2nos 35.00mx1.50=105.00 Sqm

Supplying all materials, labour, T&P and fixing water closet, squatting pan (Indian type W.C pan/Orissa pattern squatting pan) duly embedded in cement concrete (1:5:10) using 4cm size hard granite metal including fixing a pair of vitreous china 250mm x 130mm x30mm footrest etc all complete as per specification and direction of the E.I.C.580mm size Orissa pan(Hindware,Parryware)

Supplying all materials, labour, T&P and fixing Eoropian Watter closet and seat cover with 'P' trap plain etc all complete as per specification and direction of the E.I.C.

Supplying all materials, labour T&P and fitting & fixing 10 Litres capacity low level cistern with a pair of cast iron of m.s. brackets complete with fittings such as siphonic arrangements 15mm nominal size brass/pvc ball valve with polythene float, c.p. brass handle, unions and couplings for connection with inlet, outlet and overflow pipe. 32 mm C.P flush bend 15mm PVC inlet connection pipe including cutting holes and making good the same and connecting the flush bend with cistern and closet and connecting inlet pipe with supply main etc. all complete as per specification and direction of E.I.C (Cerra/ Parry ware/ Hindware)

Supplying all materials, labour T&P and fitting and fixing of C.P Shower(Parryware,Hindware) with 15mm or 20mm inlet with C.P Shower arm including polishing etc all complete as per specification and direction of the E.I.C 15 mm x 150mm dia C.P Shower with arm

Supplying all materials, labour T&P and fixing wash basins(Hindware,Parryware) with C.I. or M.S.brackets painted white including cutting holes in walls and making good the damages with supply of wooden plugs, screws and cement etc, fixing PVC waste pipe of 32mm nominal diameter for wash basin including brass check nut complete, fixing 32mm dia CP brass waste, etc all complete as per specification and direction of the E.I.C. 550mmx400mm size wash hand basin

Supplying all materials, labour, T&P and fixing mirror of superior glass mounted on 6mm thick A.C.sheet or plywood sheet and fixed to wooden plugs with CP screws and washers complete as per specification and direction of the E.I.C.

Supplying all materials,labour, T&P and fixing standard sized CP towel rail complete with CP brass brackets fixed to wooden plugs with CP screws as per specification and direction of the E.I.C 20mmx450mm long CP towel rail

Supplying all materials, labour, T&P and fixing CP soap holder complete with CP brass brackets fixed to wooden plugs with CP screws as per specification and direction of the E.I.C

Supplying all materials, labour, T&P and fitting and fixing Brass/CP fittings(Jaquar Make) of the following nominal bore with supply of all jointing materials etc. all complete as per specification and the direction of the E.I.C. 15mm dia CP Bib Cock SB

Supplying a

ll materials, labour, T&P and fitting and fixing Brass/CP fittings(Jaquar Make) of the following nominal bore with supply of all jointing materials etc. all complete as per specification and the direction of the E.I.C. 15mm dia CP Bib Cock LB

Supplying all materials, labour, T&P and fitting and fixing Brass/CP fittings(Jaquar Make) of the following nominal bore with supply of all jointing materials etc. all complete as per specification and the direction of the E.I.C. 15mm dia CP Pillar Cock

Supplying all materials, labour, T&P and fitting and fixing Brass/CP fittings(Jaquar Make) of the following nominal bore with supply of all jointing materials etc. all complete as per specification and the direction of the E.I.C. 15mm dia 2 in 1 way Bib Cock