Renovation works of godown for KSBC at State Warehouse Haripad in Alappuzha District

Amount

Renovation work

Demolishing R.C.C. work manually / by mechanical means including stacking of steel bars and disposal of unserviceable material with in 500 metres lead as per direction of Engineer -in-Charge.

Taking out doors, windows and clerestory window shutters (steel or wood ) including stacking within 500 metres lead:of area 3 sq. metes and below.

Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 500 metres lead as per direction of Engineer-in-Charge.In cement mortar

Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x15cm or nearest available size confirming to IS 2185 part I of 1979 for super structure above floor two level upto floor five level with thickness 15cm in : CM 1:6 ( 1 cement : 6 coarse sand) etc complete

Reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 150 landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (Zone III) : 3 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers.

12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) including cost of all materials, conveyance, labour charge, scaffolding etc complete as required.

Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface after preparing the surface by using wirebrush or emery paper,all works including cost and conveyance of all materials,labour charges, scaffolding etc. complete as required.Water thinnable cement primer

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:after preparing the surface by using wirebrush or emery paper,all works including cost and conveyance of all materials,labour charges, scaffolding etc. complete as required.Two or more coats on new work.

Steel work for purlin/single section with G I pipes of minimum thickness 2.00 mm including cutting, hoisting, fixing in position,including welding and bolted with special shaped washers and applying a priming coat of approved steel primer after preparing the surface by using wirebrush or emery paper,all works including cost and conveyance of all materials,labour charges, scaffolding etc. complete as required.

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, after preparing the surface by using wirebrush or emery paper,all works including cost and conveyance of all materials,labour charges, scaffolding etc. complete as required.On Steel work

Hacking of CC flooring including cleaning for surface etc. complete as per direction of the Engineer-in-Cha. rgAll works including cost and conveyance of all materials,labour charges, scaffolding etc. complete as required.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm.

Providing and fixing false ceiling with PVC multichamber hollow section (plain) 9 mm or nearest thick including frame work using 20x20x1.5 mm aluminium anodised square tubes for intermediate members in a grid pattern with spacing @60 cm centre to centre in bothways (horizontally and vertically) or at required spacing and suspended from ceiling with 20x20x1.5 mm aluminium angle, 20x20x3mm or nearest PVC angle for outer frame screwed to the walls and to the required line and levels including making provision for openings for electrical conduits etc. including cost of all labour charges etc. complete as per the direction of departmental officers.

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.80x0.90 mm M.S. laths with 0.90 mm thick to cover

Providing and fixing ball bearing for rolling shutters.All works including cost and conveyance of all materials,labour charges, scaffolding etc. complete as required.

Dismantling roofing including ridges, hips, velleys and gutters etc., and stacking the material within 50 metres lead of :Asbestos Sheet

Providing & fixing asbestos corrugated roofing sheets (thickness 2mm or above) of good quality up to any pitch, including ridges, fixing with polymer coatedhooks, bolts & nuts 8 mm dia G. I plain/ bitumen washers complete but excluding the cost of purlins, rafters, trusses and including shifting, lifting, cutting sheets to size and shape wherever required,all tools,tackles, labours, scaffolding etc.complete

Providing bitumen compound covering to G.I. bolts over roof using 0.45Kg of bitumen compound per 10 m2 area.All works including cost and conveyance of all materials,labour charges, scaffolding etc. complete as required.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285(minimum thickness of Aluminium section 1.20mm),fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required .Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge:With float glass panes of 4.0 mm thickness

Providing and fixing Thomson Multi wood board or equivalent make paneling 12 mm thick, to frame, backing or studding with screws etc. complete ( Frames, backing or studding to be paid separately) as per the direction of site Engineer-in-charge.All works including cost and conveyance of all materials,labour charges, scaffolding etc. complete as required.

Rajendra Prasad B (BID ID -1939083)

KS.MURALEEDHARAN (BID ID -1939688)

Bidder Name

Rajendra Prasad B

KS.MURALEEDHARAN

SREEJITH P