PROVN OF GENERATOR SHED NEAR NFS NODE IN ZONE R AND PROVN OF SCREEN WALL AROUND OR BATHING POINT OF FD REGT AT MIL STN AGARTALA

Amount

Schedule'A' Part-I: B&R works

Excavation in trenches n.exc 1.5 M wide and n.exc 1.5m deep as in soft/loose soil for foundation etc or for shaft walls, cesspit, manhole etc n.exc 10Sqm on plan

M&L for Excavating in post holes ( or similar holes ) each n exc 1.5 cum, getting out soft loose soil, returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm.

M & L for PCC 1:4:8 type D-2 (using 40mm graded aggregate) as in foundation filling and mass concrete.

M & L for cement concrete (1:3:6) Type C2 using 40mm graded aggregate in foundations, filling and mass concrete

Material and labour for brick work with locally available sub class ‘B’, old size, best quality bricks, straight or curved on plan exc 6 m mean radius built in cement mortar ( 1:6) all as specified and directed.

M & L returning, filling including spreading, levelling and well ramming in layers not exceeding 25 cm in each layer as in hard / dense soil complete.(Note- Soil recd from exn that are to be used in RFR in Fdn and adjecent to low laying area of fdn to avoid water stagnate)

M & L earth filling under floor spreading and levelling in layers n exc 25 cm thick for well ramming with water.( Note:- Soil shall be used neary by MOD land free of cost).

M&L for 15 mm thick rendering in CM 1:4 in finishing the surface even and smooth without using extra cement.

M&L for preparation of new plastered surfaces of walls and applying two coats of cement base paint over one coat complete all as specified and directed.

M&L roof trusses framed, trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing ( beam, tee, angle, channel or flat sections Fe-410W) including distance pieces, cleats etc.

S and F tie bars with screwed ends, nuts, washers and mild steel plates for walls, chimneys, roofs, arches, etc. king rods and straining bolts conforming to Fe?290 Gde-E-165

M and L for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete

M & L pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile stenght of 550 Mpa as in roof covering/claddiing to wall , fixed with self tapping screws as specefied.

M and L for Pre-painted galvalume based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surfaces of any description over 10cm in width or girth not otherwise described.

M and L for half brick thick brick work sub class 'B' brick straight or curved on plan to any radius in CM 1:4 complete all as spd and directed .

M & L removing excavated material exc 250 Mtrs but n exc 500 Mtrs and depositing where directed by Engineer-in-Charge.

M&L TMT bars of 10mm dia and over cut to lenth, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia.

M&L RCC type B1 (1:2:4) using 20 mm graded aggregate ) slabs supported on walls, beams and columns in floors, roos, landing,balconies deck slabs and in shelves and like.

M&L form work for flat fair finished surfaces of concrete to soffits of suspended slabs such as roof slab not exceeding 200mm thick

M & L formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete rail?ings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizon?tal or sloping and similar work exc 10cm but n exc 20cm wide

M and L for providing precast cement concrete louvres and jallies type B-0 1:2:4 using 12.5mm aggregate set and jointed in CM 1:4 , 25mm thick (mea sured solid), including all mould- ings but excluding frame (Pre cast frame shall be measur?ed separately and paid for under item

Schedule'A' Part-I: E & M works

M&L for point wiring with 1.5 Sqmm nominal cross sectional area, PVC insulated, FR unsheathed, 1100 volt grade, multistranded single core copper conductor and including PVC casing-capping minimum 25 mm wide with all fittings and accessories such as bends, Tees, Joints etc fixed to wall or ceiling and Recessed mild steel switch board of required size including bakelite sheet of 3mm thick with chromium plated screws or rectangular PVC box closed recessed having 40mm depth ISI marked ISI No 14772 Make: Presto plastic for fixing of switch etc and provision of 1.5 sqmm nominal cross sectional area, PVC insulated, FR, unsheathed, 1100 volt grade,multistranded single core green colour copper conductor for earth continuity connected to earth dolly, all metal parts, such as tube light fittings, fan hook, earth terminal of all socket points etc as specified and directed .

One light / Fan / Bell Point controlled by one way switch 5 Amp.

Supply and fixing ceiling rose, 3 Phase/ PVC/ polycarbonate, isolated body complete all as specified & directed.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

Material & Labour Switch piano, flush type single pole, one way 5 Amp complete all as specified and directed.

Material&Labour PVC rectangular block for mounting, switches, sockets, fan regulator etc. with 3 mm thick plastic laminated sheet cover of size 175 x 100 x 50mm .

M&L XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 4 sq mm.2core.

NOTES :- 1. The amount of schedule of credit shall be deducted from the total of this BOQ for arriving at contract sum. 2. Unless otherwise specified the rates for PCC shall deemed to include the cost of formwork shuttering etc, required for complete and proper execution of the work. Refer Schedule 'A' notes for details.

SHRI CHANDAN CHANDA

M/S New Saha Enterprise

M/s Amrit Gope

M/S SWAPAN DEBNATH