Webel Bhavan FF Civil Interior 07 IDM 20 21 42

Amount

Full/Half Height Partition

Supplying and erecting half height or full height partition I.e. upto soffit of the ceiling, beam, false ceiling, bulk head etc made of aluminium hollow tube (50 x 50 x 2) mm frame work for both vertical and horizontal members linked horizontally and vertically, top runners bottom skirting end trims, corner posts both horizontal as per drawing and direction with all labour and materials. Allow for cutting chase to wall, floors and mending good damages. Partition which are to be terminated at false ceiling level, the end & intermediate vertical members are to be extended upto ceiling/beam and frames are to be fitted properly by means of approved metal (Brass) expansion fastener.

Rate should include necessary hardware fittings and fixtures, adhesive, roof/height adjuster etc and arrangement shall be made to both vertical and horizontal members by cutting slots for drawing of raw power, UPS power, LAN connection, telephone etc and also making provisions for fixing of power outlets. Special cover plates, pierced for fittings of switch board should be fitted on the frame work as per drawing and direction. The rates should also include to cover the end trims by 75 mm x 25 mm (approx) Indian best quality moulded teak wood bead duly polished and malamine finish as per drawing and direction complete with all labour and materials.

Partitions made with 9 mm thick phenol formaldehyde bonded BWR and borer proof plywood with IS 303 mark fitted on both sides of the frame work with groove design. All complete as per drawing and direction with all labour and materials.(Partition measurement will be single side)

Partitions made with glass (single glazed) each glass being 6mm clear float glass of approved make fixed to aluminium frame with moulded best quality Indian teak wood beads duly polished and malamine finish of approved shade, all complete as per drawing and directions with all labour and materials.

Extra over item no. 1(a) for providing and laying 50mm thick expanded polystyrene block (self extinguishing type) having density 34.00Kg/Cum, thermal conductivity 0.28 W/M-K, water absorption 0.1% (Maximum to be laid inside the partition wall by adhesive/fasteners as per manufacturers specification and specific direction of Bank/Architect, complete with all materials and labour.

LAMINATES & VENEER

Supplying and fixing 1.00 mm thick decorative laminate of approved quality and shade fitted over plywood (plywood measured and paid separately in the respective items) to ) to partition wall, column encasing, furniture and for other surfaces as per the approved pattern and instructions. The rate should include the costs of approved adhesive (Fevicol), nail, screws etc for proper fixing as per design, drawing and direction complete in all respects with all labour and materials.

Supplying and fixing 3.5 mm thick (approx) veneer of approved quality over plywood (plywood measured separately aganst respective item) to partition, column encasing, table, cabinets and for other surfaces etc as per drawings and directions includingTwo or more coat polishing of approved shade with malamine finish. The rate should include adhesive (Fevicol) nail, screws etc and other as required hardware fittings & fixture for proper fixing complete in all respects as per drawing and direction with all labour and materials (Payment shall be made for finished surface area).

Decorative veneer with hi gloss PU polish

Supplying, fitting and fixing boiling water resistant ply conforming to IS: 303-1989 bonded with phenol formaldehyde synthetic resin of approved make and brand fitted and fixed as per design as per approval and direction of Engineer-in-Charge.[excluding the cost of supporting frame work and teak wood batten/Lipping]

Supplying, fitting and fixing boiling water proof block board conforming to IS:1659-1990 conforming to IS:848-1974 of approved make and brand, fitted and fixed as per design as per direction of Engineer-in-charge. [Excluding the cost of supporting frame work and teak wood batten/Lipping]. 19mm thik

FLOORING

Supplying , fitting & fixing Digital glazed 1st quality Ceramic tiles (Size - 600mm X 600mm or 200mm X400mm X minimum 8-10mm thick) ) in floors and dado to match with the existing work & 4 nos. of key stones (10 mm.) fixed with araldite at back of each tiles & finishing the joints with the white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface ,if necessary or by synthetic adhesive & grout materials etc. Floor With Polymerised and epoxy grout pointing including spacer-2mm (When Tiles are laid over existing hard ready surface). Colour Decorative in any floors.

Providing & laying "3M FASARA" & digital artistic self adhesive frosted film of 70-80 microns on glass surface as per approved shade and design complete with all materials and labour and as per manufactures specification.

Fittings

Wood work in post, post plates, rafters, battens, truss members, purlins,wall panelling etc. fitted and fixed complete including the cost of bolts, nails, screw etc.). Malayasian Sal

Supplying, fitting and fixing SS lock for tables/drawers/cabinets.

CPU Trolley ( Size:245X245X240 mm)( MS) made with CRCA steel with 40 to 50 micron seven to eight processing powder coating. It will be supported on twin wheel nylon castors of four nos.

Key Board Tray ( Size:510x350x55 mm)( MS) made with CRCA /Alluminium steel with 40 to 50 micron seven to eight processing powder coating. It will be fixed with the table with the C Bracket and rolling channel for smoth running

Supplying, fitting and fixing 300mm powder coated MS Telescopic channel.

Supplying, fitting and fixing 100 mm SS handle.

Supplying, fitting and fixing 75mm SS handle.

Supplying, fitting and fixing S/S hinge auto closure

Supplying, fitting, fixing of Tower Bolt as per direction of EIC

100mm long

300mm long

Supplying, fitting and fixing wire manager cap including cutting hole as required.

Supplying, fitting and fixing up to 25mm CP Teak liping including polishing.

Supplying, fitting and fixing up to 50mm CP Teak liping including polishing.

Supplying, fitting and fixing up to 2 mm thick PVC liping.

French polishing of approved shade to wood work including preparation of surface with all labour and materials in all floors as per direction.

PAINTING

Rendering the surface of walls and ceiling, beams with white cement based wall putty WATER PROOF of approved make and brand(1.5mm thick) as directed by EIC in plumb line and level including preparation of base with all labour and materials. Specific approval to be taken before execution.

Providing and applying 1st quality acrylic emulsion paint having low VOC of approved shade to interior walls, ceiling, beams, etc (two coat or more coats to achieve even shade) over and including a coat of cement primer of approved quality (as per manufacturer's specification) including cleaning, smoothening and repairing the putty surface where ever required thoroughly, scaffolding etc complete with all labour and materials in all floors. As direction of EIC

Painting with 1st quality synthetic enamel paint two or more coats to achieve proper even shade of approved shade and quality synthetic enamel paint over and inclusing a coat of approved primer to steel /wooden /other surface after preparation of surface properly with all labour & materials in all floors. As direction of EIC

Steel surface

Joinery Surface

Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

Scraping of moss, blisters etc.thoroughly from interior/exterior surface of walls necessitating the use of scraper, wire brush etc. including stagging(Payment against this item will be made only when this has been done on the specific direction of the Engineer-in-charge)

General Civil works

Dismantling carefully vitrified tiles, marble, kota stone, glazed/ceramic tiles, in flooring, steps, risers, dado skirting etc laid in cement mortar including stacking serviceable materials at site as per direction and disposal of unserviceable material from work site including mending good tod amaes to match with adjacent surface complete with all labour & materials at all floors.

Dismantling the existing false ceiling boards and its frame work and removing & stacking the same in good condition as per direction of owner/Engineer-in-Charge

Dismantling carefully wooden walling, wooden partition including glass (full heigrt) wall,flooring of ceiling and stacking dismantled materials as directed by EIC.

Removal of misc unused items from the working site and disposal of the same beyond the compound loading and cleaning the site in all respect as per direction of Engineer in charge within 10km

Removal and shiftig of unused furnitures and other materials within the compound in suitable position in other floor.

Labour charges for removal of exesting workstation & refixing the same as per direction of EIC.

Cutting chase upto 125 x 150 mm. and subsequent mending of damages.

In brick wall [Cement-3.6 Kg/Mtr]

In concrete wall [Cement-3.6 Kg/Mtr]

M.F. suspended ceiling made with 12.5 mm thick Gypsum plaster board including G.I. perimeter channel of 0.55 mm flush (having two flanges 20 mm and 30 mm respectively and web 27 mm ) along with perimeter of ceiling with G.I. intermediate channel of 0.9 mm thick size 45 mmx15mm placed at 750 mm c/c with G.I. ceiling angle of size 25 mmx10mmx0.55 mm thick fixed to the ceiling with G.I. Cleat and steel expansion fastener ceiling section 0.55 mm thick of size 51.50 mmx26mm fixed to the intermediate channels with the help of connecting clip and in the direction of perpendicular to the intermediate channel of 300 mm c/c 12.5 mm thick Gypsum plastered board are to be fixed under ceiling section as above by machine screws. The boards are to be joined and finished with jointing compound, paper tape and application of top coat etc. as per the direction of Engineer-in-charge. (The rate includes of cost of all materials including taxes, cost of accessories, fittings and fixtures, scaffolding and labour charges etc. complete)

Chair

High Back Chairs : For Manger Cabins Supply, fitting and installation of Executive High Back chair with overall dimesnion of height - 1200 to1350mm, width & depth - 650 to 800mm. The seat should be made up of 10-13 mm thick hot pressed plywood and moulded PU foam, back should be made up of injection moulded glass filled nylon and the seat & back should be upholstered using Quitted Leatherette fabric. .The armrest top should be moulded from polyurethane (PU) and should be height adjustable(6+/-.5 cm) type in differenet levels. The chair should have 360 degre revolving facility, synchronized tilting mechanism,continous adjustable lumbar support, multi point tilt locking features. The chair should have Pneumatic seat height adjustment facility (6+/-.5 cm), the pedestal should be 5 prong chrome plated pedestal with twin wheel nylon castors.

Mid Back Chairs : For Workstations, visitors,others Supply, fitting and installation of Executive Mid Back chair (Overall dimesnion: Height - 900-1100mm, width & depth - 650-800mm) The seat should be made up of 12 - 14 mm thick hot pressed plywood & moulded PU foam upholstered with fabric. The back should be made up of injection moulded glass filled nylon and upholstered with mesh fabric.The armrest top should be moulded from polyurethane (PU) and should be height adjustable type. The chair should have 360 degre revolving facility, synchronized tilting mechanism,continoous adjustable lumbar support, multi point tilt locking features. The chair should have Pneumatic seat height adjustment facility (6+/-.5 cm), the pedestal should be 5 prong chrome plated pedestal with twin wheel nylon castors.

NUNDYS

INDIA TIMBER TRADERS

Fusion

PRESCIENCE TECHNO INDUSTRIES