Construction of 6 nos. Type-III quarter for HPPWD employees at Bhawarna Distt. Kangra (HP)

Amount

Excavation in foundation, trenches etcetera in earth work involving all classification of soil such as pick work, pick jumper work, blasting work, soft or hard rocks including chiseling/wedging out of rocks where blasting work is prohibited or any other mixed variety of intermediate soil, dewatering and removal of slush if arrisen during course of construction and lifts upto all heights including stacking the excavated soil not more than three meters clear from the edge of the excavation and then returning the stacked soil in 15 cm (fifteen centimeters) thick layers when required into plinths, sides of foundation etcetera consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth within all leads,lifts by any mode of transportation and other incidental, as per the direction and entire satisfaction of Engineer-In-Charge. Any loss to the private and public property during course of construction shall be absolute responsibility of the contractor. Rate inclusive royalty, malkana, toll tax, GST and other taxes imposed by the government.

Excavation in drains and channels etc; in earth work in all classification of soil, such as pick work, jumper work, pick jumper work, blasting work, hard and soft blasting, saturated soil including chiseling or any other mixed variety of soil, lift upto any heights, stacking the excavated soil for all heights from the edge of excavation and then returning the stacked soil in 15cm (Fifteen centimeter) layer when required into plinths sides of foundations etc. Consolidating each deposited layer by ramming, watering and then disposing of all surplus excavated earth as directed by the Engineer- Incharge, within all leads, lifts of materials and other incidentals. Rate inclusive royalty, malkana, toll tax, GST and any other taxes imposed by the government.

Excavation in earth work and filling in 15cm ( Fifteen centimetre) layers in foundation and plinths including ramming, watering and consolidating upto a level of 20 (Twenty) metres and lift upto a 1.5 (One decimal five) metres. The rates are inclusive of cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Filling in plinth with sand under floor including watering, ramming, consolidating and dressing complete as per PWD specification. The rates are inclusive of cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.Rate is inclusive of royalty, malkana, toll tax, GST and any other taxes imposed by the government.

Providing form work with steel plates of 3.15mm (three decimal one five milimetre) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimetre) so as to give a fair finish including centring, shuttering, strutting and propping etcetra, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in foundation, Footings, bases of columns and mass concrete. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing form work with steel plates of 3.15mm (three decimal one five milimetre) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimetre) so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in flat surfaces such as soffits of suspended floors roofs, landings and the like floor etcetra. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing form work with steel plates of 3.15mm (three decimal one five milimetre) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimetre) so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in beams, cantilevers, girders, lintels, sides, and soffits of beams haunchings, cantilevers, bressumers and lintels upto all depths in all floor. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing form work with steel plates of 3.15mm (three decimal one five milimetre) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimetre) so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in columns, pillars , posts and struts, square, rectangular or polygonal in plain in all floor level. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing form work with steel plates of 3.15mm (three decimal one five milimetre) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimetre) so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in stairs cases with slopping or stepped soffits, excluding, landing in all floor. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing form work with steel plates of 3.15mm (three decimal one five milimetre) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimetre) so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in edges of slabs and breaks in floors and walls up to any width. The rates are inclusive of cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing form work with steel plates of 3.15mm (three decimal one five milimetre) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimetre) so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for cast in-situ reinforced concrete and plain concrete work in vertical surfaces such as walls up to any thickness/ any height.The Rate is inclusive of cost and carriage of material with all lead & lift and other incidential and toll taxes, GST and any other taxes imposed by the government.

Providing and laying cement concrete 1:4:8 (One cement isto four sand isto eight aggregate) graded crushed stone aggregate 40mm (forty milimeter) nominal size mechanically mixed and vibrated and curing complete, excluding cost of form work in foundation and plinth as per approved specification, drawing including entire carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Stone filling tightly dry hand packed under flooring including ramming and consolidation complete as per the direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidental . The rate is including of octroi, royality, Malkana, toll tax , sales tax or other taxes imposed by the government.

Providing and laying cement concrete work M20 (M-twenty) mix design to obtain the minimum compressive strength 20N/mm2 ( twenty newton per square millileter) with cement contents not less than 330 kg/ cum mechanically mixed and vibrated and curing complete excluding cost of form work and reinforcement for reinforced concrete work in foundation footing, base of columns, and the like mass cooncrete as per approved specification, drawing and design including entire carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of Royality, malkana, sale tax, toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete work M-20 design mix to obtain the minimum compresive strength 20N/mm2 (Twenty newton per square millimeter) cement content not less than 320 kg/cubic meter and curing complete and mechanically mixed and vibrated as per approved specification, drawing and design, excluding cost of form work and reinforcement for reinforced concrete work in suspended floor roofs, landing and shelves and their supports balconies, beams, girder, bressumers and cantiliver in all depth/ height upto any floor level. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete work M-20 design mix to obtain the minimum compresive strength of 20N/mm2( twenty newton per square millimetre)with cement content not less than 320 kg/cubic meter mechanically mixed and vibrated including curing complete as per PWD specification, drawing and design excluding cost of form work and reinforcement for reinforced concrete work in coulmn, pillers posts and struts in all depth/thickness upto any floor level. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete work M-20 design mix to obtain the minimum compresive strength of 20N/mm2( twenty newton per square millimetre) with cement content not less than 320 kg/cubic meter mechanically mixed and vibrated including curing complete as per approved specification, drawing and design, excluding cost of form work and reinforcement for reinforced concrete work in stair cases (except spiral stair cases) excluding landings, but including preparing of top surfaces and finishing of nosing upto all floor levels. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete work M-20 design mix to obtain the minimum compresive strength of 20N/mm2 (twenty newton per square millimetre) with cement content not less than 320 kg/cubic meter mechanically mixed and vibrated including curing complete as per PWD specification, drawing and design including cost of form work but excluding cost of reinforcement for reinforced concrete work in moulding as in cornies, window sills etcetra in girth upto all floor levels. The rates are inclusive of cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.Rate is inclusive toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete grade M-20 design mix with cement contents not less than 320 Kg (Three hundred twenty kilogram). (Three hundred twenty kilogram per Cubicmetre) mechanically mixed and vibrated and curing complete including the cost of form work but excluding the cost of reinforcement for R.C.C. work in Chajja upto all floor level including finishing the exposed surface with cement mortar 1:3 (One Cement isto Three Sand) to give a smooth and ever surface. The rates are inclusive of cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.Rate is inclusive toll tax, GST and any other taxes imposed by the government.

Providing and laying tor steel of TISCO, SAIL reinforcement for reinforced cement concrete work including bending, binding and placing in position complete in all respects as per approved drawing, design, and specification in all floor levels including the cost of binding wire and cost of dewatering if arrisen during placement of reinforcement as per PWD specification and approved, drawing design. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In- Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and laying plain cement concrete 1:2:4 (One cement isto two sand isto four graded crushed stone aggregate 20mm millimeter nominal size & curing complete, excluding cost of form work in foundation and plinth as per approved specification, drawing including entire carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete grade M-25 (M-Twenty five) design mix with minimum compressive strength 25N/mm2 with cement contents not less than 400 Kg (Four hundred kilogram) (Four hundred kilogram per Cubicmetre) mechanically mixed and vibrated including curing complete as per PWD specification, drawing and design excluding the cost of form work and reinforcement for cement concrete work in wall any thickness but not l0 meter thickness) attached pilasters, buttresses, plinth & string course etecetra including carriage of material with in all leads, lifts and other incidentals. The rate is inclusive of octroi, Royality, malkana, sale tax, toll tax, GST and any other taxes imposed by the government.

Random rubble masonry with hard stone of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (one cement isto six sand isto Twelve graded stone aggregate) 20 mm (Twenty millimetre nominal size) at plinth level in cement mortar 1:6 (one cement isto six sand ). The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and laying Damp Proof Course 100mm (One Hundred millimetre) thick with cement concrete 1:2:4 (one cement isto two sand isto four graded crushed stone aggregate 12.5mm (Twelve decimal five millimetre nominal size) mechanically mixed including cost of form work and curing complete, as per H.P.P.W.D. specification, approved drawing design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of materials within all leads lifts and other incidential. The rates is including of octroi, royality, Malkana, toll tax, sales tax or other taxes imposed by the Government.

Applying a coat of hot bitumen (mexphalt) 80/100 (Eighty by hundred) or VG-10 using 1.70 kg (one decimal seven) kilogram per square meter on damp proof course after cleaning the surface with a piece of cloth lightly socked with kerosene as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.

Second class brick work using common burnt clay building bricks in cement mortar 1:6 (one cement isto six sand) in super structure upto all floor lavels as per PWD specification drawing and design and curing complete including scaffolding. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Square rubble masonry crushed with hard stone of approved quality in foundation and plinth including racking out the joints in cement mortar 1:5 (one cement isto five sand) and curing complete including carriage of material with in all leads, lifts and other incidentals, as per the approved specification, drawing and design. Rate is inclusive of octroi, royality, malkana, toll tax,sale tax, GST and any other taxes imposed by the government.

Second class half brick work using common burnt clay building bricks with hoop iron in cement mortar 1:4 (one cement isto four sand) in super structure up to all floor level as per PWD specification, drawing and design and curing complete including scaffolding. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 40mm (forty millimeter) thick second class deodar wood panelled, glazed or panelled and glazed shutter including fixing of Modi guard 6mm (six milimetre) thick for doors, windows and clere story windows including black enamelled iron butt hinges with necessary screws. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing 40 mm thick 2nd class deodar wood wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screws. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax,sale tax GST and any other taxes imposed by the government.

Providing and fixing 19mm (Ninety millimetre) thick water proof termit resistante commercial board of Centuary/ kit ply/ Dura ply/ Action teara (ISI marked) shutter for cup board and to be finished with mica laminatory of approved shades in shutter complete including bright finished Piano butt hinges with screws including hard wood edging etcetera complete. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing 19mm (Ninety millimetre) thick water proof termit resistante commercial board of Centuary/ kit ply/ Dura ply/ Action teara/(ISI marked) shelves cup board with hard wood edging and to be finished with mica laminatory of approved shades in shelves/Box complete including bright finished black enamelled iron butt hinges with screws etcetera complete as per H.P.P.W.D. specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidential. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government

Providing and fixing 6mm (Six millimetre) thick ply wood Uniply/Greenply/ Action Teara with butt jointing and nails (Frame work and cover fillets to be measured and paid for separately). The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing 19mm (Nineteen milimetre) thick water proof termite resistant commercial board of Uniply/Greenply/Action Teara/Kitply ISI mark maked IS No.1659 in SDB shutter with 6mm (Six milimetre) thick hard wood edging and 0.63mm (Zero point six three milimetre) thick P.G.I.sheet lining on the inner side of shutter including fixing with nickel plated piano hinges with screws etc. complete. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete 1:5:10 (One cement: five sand: ten graded /broken stone crushed aggregate 40 mm (forty milimetre nominal size) mechanically mixed, curing complete excluding the cost of form work in foundation and plinth. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing Megnetic Catcher for cup boards shutter with necessary screws complete. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 65x35mm( Sixty five into thirty five millimeters) special quality chromium plated brass cup board lock with six leavers including necessary screws etc. complete (Indian make) The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing M.S. plain grills of required pattern and design in iron frames of windows/ ventilator etcetra with MS (mild steel) flats square or round bars with round headed bolts and nuts or by screws complete as per approved specification, drawing & design The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 25mm (Twenty five millimetre) diametre stainless steel curtain rods including plugs and brackets etcetra complete. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing coloured / anodized aluminum sliding door bolt, anodized transparent or dyed to required colour and shade with bolts and nuts, screws etcetra complete. 300x16mm (Three hundred into sixteen milimeter) size. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing coloured anodized aluminum tower bolts (barrel type) anodized transparent or dyed to required shade and colour with screws etcetra complete . The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In- Charge.Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

200x10mm (Two hundred into ten millimeter) size.

150x10mm (One hundred fifty into ten millimeter) size.

Providing and fixing coloured / anodized aluminum handle anodized transparent or dyed to required shade or colour with necessary screws etcetera complete. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

125mm (One hundred twenty five millimeter) size.

100mm (One hundred millimeter) size.

75mm (Seventy five millimeter) size.

Providing and fixing oxidized aluminium hooks and eyes 250 mm (Two hundred fifty millimeter) size. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 100mm (one hundred millimetre) bright finished brass floor door stopper with rubber cushion screws etcetera to suit shutter thickness. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing Hydraulic door closer of approved brand ISI marked for door including necessary fitting complete in all respect. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Ceremic glazed tiles 6mm (six millimetre) thick in skirting and dado of Nitco/ Johnson/Rak/Kajaria laid on a bed of 12mm (twelve millimetre) thick cement mortar 1:3 (one cement : three sand) and jointed with cement slurry complete. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and laying 20mm (Twenty millimetre) Kota stone 55x55/55x27.50 cm with 7.5 cm wide Jaisalmer yellow band flooring 20mm (twenty millimeter) thick base of cement mortar 1:4 (one cement : four sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including moulding and nossing complete as per approved specification, drawing and design and entire carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in- Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and laying heavy duty vitrified tiles of Nitco/Kajaria/Orient/Johnson/Rak double charged 600x600x10mm (Six hundred into six hundred into ten millimeter) of approved shade and colour in flooring, tread of steps and landings laid over 12mm (Twelve millimetre) thick cement mortar 1:3 (One cement isto three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete upto all floor level in all heights as per approved specification, drawing and design and entire carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in- Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and laying 300 x 300mm (Three hundred into three hundred millimetre) size antiskid (Non slippery) vetrified tiles of Nitco/Kajaria/Orient/Johnson/Rak in flooring, treads of steps laid on a bed of 12mm (Twelve millimetre) thick cement mortar 1:3 (One cement isto three sand) finished with flush pointing in white cement.complete upto all floor level in all heightsas per approved specification, drawing and design and entire carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in- Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and laying 20mm (Twenty millimetre) thick Granite stone in work top laid over 20mm (Twenty millimetre) thick base of cement mortar 1:3 (One cement isto three sand) including jointing with cement mortar 1:2 (One white cement isto two marble dust) with an admixure of pigment to match the shade of granite stone as per approved specification, drawing and design including rubbing, cutting, nosing and moulding complete in all respect and entire carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In- Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and laying 60 mm ( Sixty millileters) thick heavy duty precast cement concrete inter locking paver blocks of NTC with vibro compacted upto M-50 grade including border or kurb block grey or coloured over sub-base of concrete with 25mm( twenty five millimeters) thick average thickness of cement mortar 1:4 (one1 cement :four sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks including curing rubbing & polishing complete (Sub base concrete floor to be measure sepertely. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 150mm single acting spring hinges with necessary screws etcetra complete. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 0.60mm (sixty millimetre) thick prepainted steel sheet (IS marked Z-120) of TATA durashine/ sail over steel trussed in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating of back coat of polyster of 5 (Five) microns over 5 (Five) microns primer coating Tata/ Sail/ Reliance/ Jinda including fixing with prepainted iron J or L hooks,bolts and nuts 6mm (six millimetre) diametres with prepainted limpet and rubber washers complete with all accessories as required as per the direction of Engineer-in-charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing pre-painted steel sheet ridge or hips of TATA Durashine/ Sail 60cm (sixty centimetre) over all with 0.60mm (zero decimal six zero millimetre) thick prepainted sheet in roofing with hot dipped metalic zinc coated sheets with top coat of regulat modified polyster organic coating of 20 (twenty) microns over 5 (Five) microns primer coating + back coating of polyster of 5 (Five) microns over 5 (Five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (Six millimetre) dia prepainted bitumen washers complete in all respect as per approved drawing and design. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing pre-painted sheet valleys 90cm (Ninety centimetre) over all with 0.60mm (zero decimal six zero millimetre) thick prepainted sheet of TATA Durashine/ Sail in roofing with hot dipped metalic zinc coated sheet with top coat of regulat modified polyster organic coating of 20 (twenty) mocrons over 5 (Five) microns coating + back coat of polyster of 5 (Five) microns over 5 (Five) microns primer coating including fixing with J or L hooks, bolts and nuts 6mm (Six millimetre) dia with prepainted limpet and bitumen washers complete in all respect as per approved drawing and design. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 30cm (Thirty centimetre) wide 30cm (Thirty centimeter) deep 0.63mm (zero decimal six three millimetre) thick plain G.I. sheet gutter of TATA Durashine/ Sail with bolts and nuts and washers etcetra and having dome shape gratting including making necessary connections with rain water pipe complete as per design, drawing and specifications.The rate is inclusive of cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing M.S. B.P. sheet 2 mm (two millimetre) thick eaves board/Facia/Soffit/Ceiling including cutting, fixing and gass/electric welding steel roof member and applying a coat of red lead primer complete as per PWD specification (frame work is to be measured and paid for separately). The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing on wall face PVC (D-plast) rain water pipes of Finolex/Supreme/ Prince of working pressure not less than 4.00/6.00 kg (four to six kilogram) per centimetre square including filling the joints with approved adhesive complete 110 mm (one hundred milimeter) diametre ISI marked pipe. The rates are inclusive of cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing on wall face PVC (D-plast) accessories for rain water pipes of Finolex/Supreme/ Prince including filling the joints with approved adhesive complete as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer- In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

110mm (one hundred ten millimeter) dia PVC plain bend

110mm (one hundred ten millimeter) dia PVC shoe

Providing and fixing 110 mm (One hundred ten millimeters) diametre PVC Clamps fitted with steel screws and rawal plug etcetra complete. The rates are inclusive of cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer- In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Steel work welded in built up sections of TATA/Sail composed in beams, joists, channels, angles, tees flats with connecting plates or angles, cleats as in trusses and trussed purlins, main and cross beams, hips, jack rafters, purlins connect to common rafter and like work including cutting hoisting fixing in position & applying a priming coat of red lead paint complete including entire carriage of material within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing M.S. channels of TATA/Sai in doors, windows clerestory windows frames manufactured from M.S. channel section 35x35x4mm (Thirty five into thirty five into four millimetre) with M.S. flat 50x4mm (Fifty into Four millimetre) combination as per specifications design, drawing including hinges, jambs, beads if required thrashold of M.S. angles 50x25mm (Fifty into Twenty five millimetre) welded or rigidly fixed by mechanical means lugs, with split ends tails to each jambs including steel butt hinges 2.5mm (Two decimal five millimetre) thick with a provision of locking arrangements, shock observers as specified and applying a coat of approved steel primer after pretreatment of the surfaces as directed by the Engineer-in-Charge. The rate is inclusive for carriage of material with in all leads, lifts and other incidentals including sale tax, toll tax, GST or all type of other taxes imposed by the Government.

Providing and fixing angle iron cup-board frames of TATA/Sail manufactured from M.S angle iron sections 25x25x5mm (Twenty five into Twenty five into Five millimetre) thickness including hinges jambs, lock jambs, beed and if required angle threshold of mild steel 25x25x5mm (Twenty five into twenty five into five millimetre) welded or rigidly fixed by mechanically means luge split and tails to each jambs including steel butt hinges 2.5 mm (Two decimal five millimetre) thick with provision for locking arrangements and shock absorbers as specified and applying a cost of approved steel primer after pre-treat-ment of the surfaces or as directed by the Engineer-in-Charge including carriage of materials within all leads and lifts and other incidentals .

Providing and fixing M.S. channels of TATA/Sail in doors, windows clerestory windows frames manufactured from M.S. channel section 75x40x4mm (Seventy five into Forty into four millimetre) with M.S. flat 75x4mm (Seventy Five into Four millimetre) combination as per specifications design, drawing including hinges, jambs, beeds if required thrashold of M.S. angles 50x25mm (Fifty into Twenty five millimetre) welded or rigidly fixed by mechanical means lugs, with split ends tails to each jambs including steel butts hinges 2.5mm (Two decimal five millimetre) thick with a provision of locking arrangements, shock observers as specified and applying a coat of approved steel primer after pretreatment of the surfaces as directed by the Engineer-in-Charge. The rate is inclusive for carriage of material with in all leads, lifts and other incidentals including sale tax, toll tax, GST or all type of other taxes imposed by the Government.

Providing and fixing double steel shutter windows side hung ( one glazed and other wire gauged) including frame of channels ISLC-75 (Seventy five ) flappd with mild steel flat 75 X 4mm (seventy five into four millimetre) and 50 X 4 mm (fifty into four millimetre) in the opening side of channels to make multi frame and shutter of rolling steel Z-section and T-section and T-hinges, handles with closing device and making provision of fixing of window with 16X 3.15 mm (Sixteen into three decimal one five millimtre) l0 cm (ten centimeters) long embedded in cement concrete block 15 X 10 X 10 cm ( Fifteen into ten into ten centimetre) size of 1:3:6 (one cement isto three sand isto six garded crushed stone aggregate 20 mm (twenty millimetre) nominal size or with wooden / steel plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as required and iron fittings including 4 mm (four millimtre) thick glass panes with glazing clips and special metal sesh putty of approved make for glazed shutter and metal beading with screws etcetera and including fixing of wire guage shutter using galvenised MS wire guage of IS guage designation 85-G (eighty five-G) with wire of 0.56 mm (zero decimal five six millimetre) and for fixing wire mesh with MS flats 20 X 3 mm (twenty into three millimetre) for beading and screws and applying a primimg coat of approved steel primer after pretreatment of the surfaces as direction of the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, sales tax, toll tax, GST or all types of other taxes imposed by the Government.

Providing and fixing 5mm thick (Five millimetre) plain asbestos cement sheet ceiling of approved quality with butt jointing and wood screws (Frame work and cover fillets to be measured and paid for separately) including carriage of materials within all leads, lifts and other incidentals as direction of the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkana, sales tax, toll tax, GST or all types of other taxes imposed by the Government.

Supplying and fixing expended metal to wood or steel members to obtain the minimum weight not less than 5kg (Five Kilogram) per square metre in partitions etc. The rates are inclusive cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and laying double coat water proffing treatment in depressed toilet area shall be done with Dr. Fixit Pidilite water proof coating shall be done in two coats apply first coat of Dr. Fixit Fast flex to the clean and saturated surface maintaing a coverage of 6-7 sq ft. ( 0.60 sqm) per Kg(Kilogram) to achieve 1mm thickness. This coating shall also be extended upto 30mm vertically. The second coat shall be applied in opposite direction after 4-6 (Four to six) hours of application of first coat then sprinkle sand on top surface of applied Dr. Fixit Fast flex while still tacky over the second coat. Then apply cement mortar 1:4 ( 1 Cement; 4 Sand ) admixed with Pidiproff L.W over the floor with suitable gradient words drain water pipe while the second coat of Dr. Fixit is till tacky.

Providing and fixing moulded hand rail of M.S hollow pipe 50mm (Fifty Milimetre) diametre welded in straight length over M.S. flat at top of vertical balusters including one coat of red oxide priming coat complete (M.S. flat & balusters of railings shall be measured & paid separately) . The rates are inclusive of cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing M.S. rectangular pipe stair railing over M.S. flat having baluster 20mmx20mm and 12mmx12mm (Twenty milimetre into twenty milimetre and twelve milimetre into twelve milimetre) M.S. solid square bars in combination with M.S. flat 40x6mm (Forty into six millimetre) with a clear height of 85cm (Eighty five centimetre) @ 60 (Sixty) centimetre centre to centre, embeded in cement concrete steps and jointing with electrical gas welding at top along with hand rail of hollow M.S rectangular pipe of 75x25mm (Seventy five into twenty five) ( SWG-16) Vertical M.S solid squiare bars, baluster welded/ jointed with each with 2 Nos. (Two number) M.S flat of 40x6mm (Forty into six millimetre) complete with a priming coat of read lead paint as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing hollow M.S. pipe of 50mm (Fifty millimetre) diameter hand rail slip resistant with round ended joint at two levels at 75 and 90cm (Seventy five and ninety centimetre) height welded with 25mm (Twenty five millimetre) diametre baluster embeded in cement concrete 60 (Sixty) centre to centre jointing in with electrical gas welding at top along wing hand rail of hollow M.S pipe of 50mm (Fifty millimetre) diametre ( SWG-16). The balusters welded/ jointed with each with 2 Nos (Two numbers) M.S flat of 50x5mm (Fifty into five millimetre) complete with applying priming coat of red lead paint as per specification and direction of the Engineer-in-Charge. The rate is inclusive for carriage of materials within all leads, lifts and other incidentals.

Painting two coats of Nerolac/Berger/Asian Paint (excluding priming costs) on new steel and other metal surfaces with enamel paint to give an even shade including cleaning the surfaces of all dirt, dust and other foreign matters complete as per PWD specification. The rates are inclusive cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Applying a priming coat of Nerolac/Berger/Asian Paint over new wood and wood bases surfaces after and including preparing the surface by thoroughly cleaning, oil, grease, dirt and other foreign matter, sand papering and knotting with ready mixed paints brushing wood primer pink as per PWD specification. The rates are inclusive of cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Painting two coats of Nerolac/Berger/Asian Paint (excluding priming coat) on new wood and wood based surfaces with enamel paint brushing to give an any shade including cleaning the surfaces of all dirt, dust and other foreign matters sand papering and stopping as per PWD specification. The rates are inclusive cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

6mm (six millimeter) cement plaster 1:3 (one cement isto three sand) in ceiling complete including curing and scaffolding complete as per PWD specification. The rates are inclusive cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

15mm (fifteen millimeters) thick cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering upto any floor level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (eighty milimetewrs) in girth, in rough side with cement mortar 1:6 (one cement isto six sand) complete including curing as per PWD specification. The rates are inclusive cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

15mm (fifteen millimeter) thick cement plaster in single coat on the fair side of brick/concrete/stone walls for exterior plastering upto any floor level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (eighty millimeters) in girth, with cement mortar 1:6 (one cement isto six sand) complete including curing as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

15mm (fifteen millimeter) thick cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering upto any floor level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (eighty millimeters) in girth, with cement mortar 1:6 (one cement isto six sand) complete including curing as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

15mm (fifteen millimeter) thick cement plaster in single coat on the fair side of brick/concrete/stone walls for exterior plastering upto any floor level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (eighty millimeters) in girth, with cement mortar 1:4 (one cement isto four sand) complete including curing as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing throating or plaster drip and moulding to R.C.C. Chhajja including carriage of materials within all leads, lifts and other incidentals as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Distempering (two or more coats) with oil bound washable distemper of Berger/Nerolac/Asian Paint and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings & other foreign matter and also including preparing the surface even and sand papered smooth priming coat with distemper primer as PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on undecorated wall surfaces (Two or more coats) to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing under layer for plinth protection of 75 mm (Seventy five millimetre) thick unconsolidated) bed of dry brick stone broken aggregate 40mm (Forty millimetre) nominal size well rammed and consolidated and grouted with fine sand including preparation of ground per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing plinth protection 50mm (Fifty millimetre) thick with cement concrete 1:3:6 (One cement isto Three sand: Six graded stone aggregate 20mm (Twenty milimetre)nominal size including finishing the top surface of concrete smooth per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government..

Construction of cement concrete covered drain in cement concrete 1:3:6 (One cement isto Three Sand isto Six graded stone aggregate 20mm (Twenty milimetre) nominal size_ including earth work shuttering and cast in-situ RCC slab over drain and cement concrete flooring 1:2:4 (One cement isto Two sand isto Four graded stone aggregate) and finished with a floating ncoat of neat cement complete as per standard design. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government..

Providing and fixing to wall ceiling and floor galvanised mild steel tubes of TATA steel/jindal (Hissar) (Heavy grade) tube fittings and clamps including making good the wall, ceiling and floor. The rates are inclusive cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

15 mm nominal bore/ diametre.

20 mm nominal bore / diametre

Providing and fixing G.I. sockets of Tata steel/ Jindal ISI Marked including fixing with approved adhesive etc. complete within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

15 mm ( Fifteen millimeter) diametre

20 mm ( Twenty millimeter) diametre

Providing and fixing G.I. Tees of Tata steel/Jindal ISI Marked including fixing with approved adhesive etc. complete within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

15 mm ( Fifteen millimeter) diametre

20 mm ( Twenty millimeter) diametre

Providing and fixing G.I. Elbow of Tata steel/ Jindal including carraige of material within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

15 mm ( Fifteen millimeter) diametre

20 mm ( Twenty millimeter) diametre

Providing and fixing G.I. Nipples ISI Marked of Tata steel/ Jindal including carraige of material within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

15 mm ( Fifteen millimeter) diametre

20 mm ( Twenty millimeter) diametre

Providing and fixing G.I./M.I. Union ISI Marked of Tata steel/ Jindal including carraige of material including fixing with approved adhesive etc. complete within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

15 mm ( Fifteen millimeter) diametre

20 mm ( Twenty millimeter) diametre

Making connection of galvanised mild steel distribution branch with galvanised mild steel main 20mm (Twenty millimetre) including carraige of materail within all leads, lifts of material and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing high pressure P.V.C spigot and socket soil, waste and ventilating pipe of Supreme/Finolex working pressure not less than 6.0 kg/m2(Six kilograme per square metre) I.S.I Marked including fixing with approved adhesive etc. complete The rate is inclusive for carriage of material within all leads, lifts and other incidentals. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

110 mm (One hundred millimeter) diametre (4.6mm) Four decimal six millimetre thick

75 mm (Seventy five millimeter) diametre (2.7mm) Two decimal seven millimetre thick

Providing and fixing PVC holder bat clamps of approved design rain water pipe embedded in cement concrete blocks 10x10x20cm (Ten into Ten into Twenty centimetre) of 1:2:4 (One Cement isto Two Sand isto Four graded crushed stone aggregate) 20mm (Twenty milimetre) nominal size and cost of cutting holes and making good the walls etc. The rate is inclusive for carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-Charge.

110 mm (One hundred millimeter) bore/diametre

75 mm (Seventy five millimeter) bore/diametre

Providing and fixing PVC Plain Bend ISI Marked of Finolex/ Supreme including fixing with approved adhesive etcetra Complete including carraige of materail within all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

110 mm ( One hundred ten millimeters)

75 mm ( Seventy five millimeters)

Providing and fixing PVC Tees of Finolex/ Supreme (Medium Class) ISI Marked including fixing with approved adhesive etcetra complete including carraige of materail within all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

110 mm (One hundred ten millimeter) diametre

75 mm ( Seventy five millimeter) diametre

Providing and fixing PVC Supreme/Finolex/Astral heal rest including filling the joints with approved adhesive complete within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

110 mm (One hundred ten millimeter) diametre

75 mm ( Seventy five millimeter) diametre

Providing and fixing PVC Supreme/Finolex/ Astral Collar complete within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

110 mm (One hundred ten millimeter) diametre

75 mm ( Seventy five millimeter) diametre

Providing and fixing PVC door bend of Finolex/ Supreme with ovel access door, insertion rubber washer 3mm (three millimetre) thick bolts and nuts ISI marked complete including fixing with approved adhesive etcetera complete including carriage of material within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

110mm (one hundred ten millimetre) diametre.

75mm (seventy five millimetre) diametre.

Providing and fixing PVC Floor Trap size 110x75 mm ( one hundred ten into seventy five millimeters) ISI marked self cleaning design od Finolex/ Supreme including fixing with approved adhesive cost of cutting and making good the wall and floor complete including carriage of material within all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing PVC Single Equal Branch with oval access ISI Marked of Supreme/ Finolex insertion rubber washer 3 mm (Three millimetre) thick bolt and nuts complete including fixing with approved adhesive etcetra Complete including carraige of material within all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

110 mm ( One hundred ten millimeter)

75 mm ( Seventy five millimeter)

Providing and fixing vitreous china wash down water closet of Hindware/ Cera/ Jaguar European type W.C. Pan with integral P or S trap including jointing the trap with soil piper in cement mortar 1:1 (One Cement: One Sand) seat cover to be measured and paid for separately) Anglo Indian Universal closet) No. 2012 size. The rate is inclusive for carriage of material within all leads, lifts and other incidentals. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 10.0/12.50/15.00 ltrs.(Ten oblique twelve point five zero oblique fifteen litre) PVC low level dual flushing cistern of Hindware/ Cera/ Jaguar with a pair of CI or mild steel brackets complete with fitting such as lead valve less syphon, 15 mm nominal size brass bass valve with polythene float, CP brass handle unions and couplings for connections with inlet, outlet & overflow pipes, 40mm (Forty milimetre)dia. CP flush bend i/c cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately. The rate is inclusive for carriage of material within all leads, lifts and other incidentals. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing 32mm (thirty two millimetre)diametre galvanized steel tube flush pipe for low level flushing cistern including connecting the flush pipe with cistern and closet making good the walls and floors in position with clamps etc. The rate is inclusive for carriage of materials within all leads, lifts and other incidentals. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing plastic seat hollow type white seat and cover for washed and water closet of Hindware/ Cera with chromium plated brass hinges and rubber buffers. The rate is inclusive for carriage of material within all leads, lifts and other incidentals. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing vitreous china wash basin of Hindwre/ Cera/ Jaguar Delta No 10010 and size 55x40 cm ( fifty five into forty centimeters) Hindware/Cera/Jaguar with double hole for pillar trap with C.I. or M.S. brackets including hole in walls and making good the same (under counter basin) including all fitting complete in all respect including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing heavy quality stainless steel kitchen sink of AMC/UNIK/ DIAMOND ISI marked with drain board and C.P. waste pipe C.I. or M.S. brackets painted white i/c cutting holes and making good the same including fitting 600x480x150 mm (six hundred into four hundred eighty into one hundred fifty millimetre) with bowl depth 20 mm ( twenty millimeters) including entire carriage of material within all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing vitreous china pedestal for wash basin CERA/ Hindware/ Cera/ Jaquar make at the back for the resption of pipe and fitting including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 32mm (Thirty two millimetres) nominal size diameters rubber plug for wash basin sink, within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 32mm (Thirty two millimetres) nominal size diameters M.I. union for wash basin sink, within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 32mm (Thirty two millimetres) diameters C.P. brass waste (Heavy duty make ISI marked NO-8931 & 8934) Jal/ Jaguar for wash basin or sink with in all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 100mm (One hundred milimetres) nominal size diameters CP grating of ESS/ JAL/ Jaquar trap of approved brand complete, within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 600mmx450mm (six hundred millimeter into four hundred fifty millimeter) beveled edge mirror of superior glass of Atul/Modigurard/ Saint Gobianmounted on 6mm (six millimeter) thick A.C. Sheet or plywood sheet and fixed to wooden plugs with C.P. screws and washers of Atul/Modi Guard/ Golden fish including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing C.P. brass towel rail size 600x20mm (Six hundred into twenty millimetre) of JAL/ESS/Jaguar with C.P. brass brackets fixed to wooden plugs with C.P. brass socket including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 600x120mm (Six hundred into one hundred twenty milimetres) glass shelf with C.P. brass brackets and guard rail complete fixed to wooden plugs with C.P. brass screws, within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing C.P. (Charomium plated) brass Toilet paper holder of JAL/Jaguar/ESS within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and fixing PTMT/PVC jet sprey of JAL/ESS/ Jaguar for Europen seat of approved brand and manufacture, within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 15mm (Fifteen millimetres) diameters C.P. brass push cock tap of JAL/ESS/Jaguar within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 15mm (Fifteen millimetres) diameters C.P. brass bib tap of Jal/Jaguar/ESS within all leads, lifts of materials and other incidental, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing C.P. brass pillar tap Jal/ESS/Jaguar 15mm (fifteen millimetre) dia (Heavey duty makes ISI marked No. 8931 & 8934) including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 15mm (fifteen milimetre) C.P. Brass Angle valve Jaguar/ESS/Jal without nuts & bolts including carriage of material within all leads, lifts, and other incidentals. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing C.P. brass full way valve with wheel of Jaguar/ESS/Jal within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

15 mm ( Fifteen millimeter) nominal size bore.

20 mm ( Twenty millimeter) nominal size bore.

Providing and fixing brass ball valve ( Horizontal plunger type) high pressure of Jaguar/Jal/ESS with copper float 15mm (fifteen millimetre) nominal bore of continental series/ clasic series/ floral series of Hindware/Jaguar/Cera within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing PVC connection 15 mm( fifteen millimeters)nominal bore and 450 mm ( four hundred millimeters) long including necessary fitting complete and entire carriage of material within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and placing water tank of make PVC (Poly venyl chloride) Sintex (Triple layer) having capacity 1000 ( One thousand) litres each with necessary fitting including over flow pipes scour pipe and bull valve and with cover locking arrangement of good quality including providing pads of sizes as required for inlet and outlet and inside painting of good quality all complete including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and laying ( to level or slope) of PVC 150 mm (One hundred fifty millimetre) of Finolex/Supreme/Prince sewerage pipe of working pressure not less than 6.0 kg/cm2. (Six kilogrms per square centimetre) of including filling the joints with approved adhesive complete. The rates are including cost and carriage within all leads and lifts and other incidentals as per PWD specification and entire satisfaction/direction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete 1:5:10 (1 Cement: 5 Sand :10 graded stone aggregate 40mm nominal size ) bedding for stoneware pipes of the 150 mm ( One hundred fifty millimeters) internal diameters, necessary form work and curing complete within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Construction manhole with R.C.C. top slab in 1:2:4(One cement: Two sand: Four graded crushed stone aggregate 20mm(Twenty milimetre nominal size), foundation concrete 1:4:8 (One cement: Four sand: Eight graded crushed stone aggregate 40mm(Forty milimetres nominal size) inside plastering 15mm (Fifteen milimetre) thick with cement mortar 1:3 (One Cement: three sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4(One cement: Two sand: Four graded crushed stone aggregate 20mm(Twenty milimetres nominal size) finished smooth complete including curing and testing inside size 800x800mm (Eight hundred into Eight hundred milimetre) 500mm(Five hundred milimetre) deep, including C.I. cover with frame (light duty single seal pattern–I) 450x610mm (Four hundred fifty into six hundred and ten milimetre) internal dimensions total weight of cover and frame to be not less than 38 Kgs (Thirty eight kilogram) weight of cover 23Kgs(twenty three kilogram) and weight of frame 15 Kgs (Fifteen kilogram) with 300mm (Three hundred milimetre) thick walls of squared rubble masonry coursed with hard stone of approved quality in cement mortar 1:3 (one cement: three sand) including carriage of material within all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Construction manhole with R.C.C. top slab in 1:2:4 (One cement: Two sand: Four graded crushed stone aggregate 20mm(Twenty milimetres nominal size), foundation concrete 1:4:8 (One cement: Four sand: Eight graded crushed stone aggregate 40mm(Forty milimetres nominal size) inside plastering 15mm (Fifteen millimetres) thick with cement mortar 1:3 (One Cement: three sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4(One cement: Two sand: Four graded crushed stone aggregate 20mm(Twenty millimetres nominal size) finished smooth complete including curing and testing inside size 800x800mm (Eight hundred into Eight hundred millimetres) 1000mm(One thousand millimetre) deep, including C.I. cover with frame (light duty single seal pattern–I) 450x610mm (Four hundred fifty into six hundred and ten millimetre) internal dimensions total weight of cover and frame to be not less than 38 Kgs (Thirty eight kilogram) weight of cover 23Kgs(twenty three kilogram) and weight of frame 15 Kgs (Fifteen kilogram) with 300mm (Three hundred millimetre) thick walls of squared rubble masonry coursed with hard stone of approved quality in cement mortar 1:3 (one cement: three sand) including carriage of material within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Constructing brick masonry chamber for under ground CI inspection chamber and bends with common burnt clay building bricks in cement mortar 1:5 (one cement : five sand) cover with frame (light duty) 355mmx610mm (Three hundred fifty five millimetre into six hundred ten millimetre) internal dimensions. Total weight of cover with frame to be not less then 38Kg. (weight of cover 23Kg. and weight of frame 15Kg) RCC top slab with 1:2:4 (one cement : two sand : four graded stone aggregate 20mm (Twenty millimetre nominal size) foundation concrete 1:5:10 (one cement isto five sand isto ten graded stone aggregate 40mm (forty millimetre) nominal size), in side plaster 15mm (fifteen millimetre) thick with cement mortar 1:3 (one cement isto three sand) finished smooth with floating coat of neat cement on wall and bed concrete etcetra complete. Inside dimension 455x610x450mm (Four hundred fifty five into six hundred ten into four hundred fifty millimetre) deep single pipe line. The rates are including cost and carriage within all leads lifts and other incidentals as per PWD specification and entire satisfaction/direction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and laying (to level or slopes) and jointing with adhesive of approved brand PVC pipes grade 'A' of the 150 mm (One hundred fifty millimetre) internal diameter including testing of pipes and joints and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

Providing and fixing 150mm dia (one hundred fifty millimetre) PVC Plain Bend ISI Marked of Supreme/Finolex/Prince including fixing with approved adhesive etcetra Complete including carraigre of material within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government.

vinay kumar gupta