Certain revenue and minor works under GE Derhdun.

Amount

Surface excavation n.exc(not exceeding) 30 cm deep and averaging 15cm deep and getting out soft and loose soil complete all as specified and directed.

Excavation in trenches in any type of soil, n. exc. 1.5m wide and n. exc. 1.5m deep and getting out for foundation, UG Cable etc complete all as specified and directed.

Material and labour PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in foundation filling, mass concrete, sub base or leveling course of floor etc. complete all as specified and directed.

Material and labour for Brickwork with subclass ‘B’ bricks old jsize, straight or curved on plan exc 6m mean radius built in cement mortor 1:6 complete all as specified and as directed.

Returning filling in, including spreading, leveling, watering and well ramming in layers n. exc 25 cm thick in any type of soil complete all as specified and directed.

Removal of surplus excavated soil to a distance n. exc. 50 m and depositing where directed at a level n. exc. 1.5 m above starting point complete all as specified and directed.

Material and labour for with 15 mm thick rendering on of brick work or concrete surfaces in cement mortar 1:4 finished surfaces even and smooth without using extra complete all as specified and as directed by Engr-in-Charge.

Material and labour for with 15 mm thick rendering on of brick work or concrete surfaces in cement mortar 1:6 finished surfaces even and smooth with using extra cement complete all as specified and as directed by Engr-in-Charge.

Material and labour finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and directed.

Supply and fix plate girder or single stanchions, built up of one beam or channel section with flange plates, caps, bases. splices, angle brackets, cleats and other connections complete all as specified and directed

Supply and fix roof trusses (framed), trussed,purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel ,hollow sections or flat sections) including distance pieces, cleats etc Fe-290(Gde E 16 complete all as specified and directed .

Supply and fix Pre- painted galvatume aluminum zinc coating round shape and arch type GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as etc complete all as specified and directed .

Supply and fix Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Material and labour applying two coats of synthetic enamel paint on new or previously untreated steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete all as specified and directed.

Material and labour for 100mm thick cement concrete type C - 2, 1:3:6 (40mm graded stone aggregate) for sub base etc complete all as specified and directed.

Material and labour for 25 mm thick cement concrete in 1:2:4 type B-1 ( 20mm graded stone aggregate) below floor tiles etc complete all as specified and directed.

Material and labour virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry @ 3 kg/ sqm and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

Material and labour 75mm thick PCC 1:3:6 type C-2, (20 mm graded stone aggregate)as plinth protection and finishing even and smooth without using extra cement, complete all as specified and directed.

Material and labour for preparation of newly plastered surface of walls including corners and applying two coats of White wash complete all as specified and directed.

Material and labour for providing & fixing false ceiling of Designer tile Ivory painted (High Pressure Steam cured) of 4mm thickness (as per IS : 14862) of size 595x595mm and any one of the design (Cascade or electra) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel section (Galvanised @120 grams, both side inclusive and black painted groove on all T webs) consisting of main T runner with suitably spaced joints to get required length and 15x32mm made from 0.30mm thick sheet spaced at 1200mm c/c and cross 'T' of size 15x32mm made of 0.30mm sheet 1200mm long spaced between main "T" at 600 mm c/c to form a grid of 1200x600mm and secondary cross "T" of length 600mm and size 15x32 mm made of 0.30mm thick sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x22x0.40mm and laying false ceiling tiles in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable wire of 4mm dia with galvanised butterfly level clips, spaced at 1200mm c/c along main 'T', bottom exposed width of 15mm of all 'T'' sections of 4mm dia GI wire shall be pre-painted with polyester paint and black painted groove at center of size 4mm depth and 4.5mm width, complete all as specified and directed.

Supply and fix Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.) hinges type B-21 100mm long (2 no.) suitable handle (1no.), and 5.5 mm thick sheet glass complete all as specified and directed.

Material and labour for excavating in post holes (or similar holes) in soft/loose soil each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm and removing surplus soil to a distance n exc 50m and making good surface in any type of soil complete all as specified and directed.

Material and labour for cement concrete type C2 1:3:6 (40mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

Supply and fix for hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

Supply and fix Pre- painted semi-circular or straight (as directed) galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Material and labour 75 mm thick PCC (1:4:8) type D-2 using 40 mm graded stone agg as in sub base complete all as specified and as directed by the Engr-in-Charge.

Material and labour for 60 mm thick pre polished rubber moulded coloured machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658- 2006 M-35 Grade with grey cement and no pigment complete all as specified and as directed by the Engr-in-Charge.

Material and labour for sand filling 25mm thick under floors or in foundations covering of UG cable including watering and consolidation complete all as specified and as directed.

Material and labour for dark coloured Glazed ceramic tiles in vertical surfaces of size 450x 300 x 6mm thick over and including 10 mm thick bedding layer in CM 1:4 , set and jointed in neat cement slurry @ 3 kg / sqm and pointed in white or coloured cement to match all as directed.

Taking out & removing existing roof treatment of any description completely upto concrete surface including racking out joints, hacking for key,sweeping clean and scrubbing down with water etc to remove dust etc,complete all as specified.

Material and labour for brushing neat cement slurry @ 3 Kg of cement per Sqm on cleaned roof/wall surface complete all as specified and directed.

Material and labour for rendering 10 mm thick in cement mortar 1:4 mixed with water proofing compound @ 3% by weight of cement in roof surface, complete all as specified and as directed. (Note- WPC shall be measured and paid separetely.)

Supply only integral water proofing compound as per manufacturers instructions , complete all as specified and directed.

Material and labour for Water proofing roof treatment with Polymeric water proofing membrane of weight not less than 3Kg/sqm and minimum 3mm thick, five layers with center core as 90 micron high molesuvre, high density polythene film sand witched between two layers of polymeric (Static polythene based) between laminated on both sides with 20 micron HMDPF film over a coat of hot blown bitumen with 85/25 grade @ 1.20 Kg/Sqm after priming the surface with bituminous emulsion @ 0.30 Litre/Sqm on plastered surface. Water proofing membrane should be laid with over laps 150 mm at ends and 75 mm for sides and shall be bounded uniformity by LPG torch flame over the polymeric water proofing membranes apply semi hot blown bitumen 85/25 grade @ 1.20 Kg/ sqm dusted sand over the coat of the coat @0.5 Kg/Sqm, and applying aluminium reflective paint over it complete all as specified and as per manufacturers instructions. Note : - The water proofing treatment shall be got carried out by the manufacturer or their authorised applicators duly approved by GE in writing. (ii) 2.5% amount of the total amount of water proofing treatment shall be retained as a guarantee and shall be released after 10 years. However contractor may deposit the FDR of same amount in favour of GE. If contractor fail to rectify the defect pointed out during this period in writing, the defect shall be got rectified at contractor risk and cost and the payment shall be made from the amount kept reserved or by encashing the FDR deposited by the contractor as guarantee. Contractor's quoted rate for this item shall deemed to be inclusive of this aspect.

Supply and fix PVC (SWR) pipes of 150 mm dia, single socketed fixed to walls or laid in trenches or floors complete all as specified and directed.

Supply and fix PVC (SWR) bends of 150 mm dia, any radius complete all as specified and directed.

Supply and fix MS joist channel (Fe 410-W Gde E-250 Quality A), angle or Tee section, MS tubes, flats square bars etc fixed indepently or framed or without connecting plates ,trusses etc any type framing including purlins and rafters etc confirming to Grade Fe 410-0 or Fe-310-0 complete all as specified and directed by Engr-in-Charge

Material and labour for cement concrete 1:2:4 type B-1 (using 20mm graded stone agg) as in roof kerbs or mud stops, rounded or chamfered on edges , in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed

Supply and fix butt hinges 100mm , heavy weight, cold rolled mild steel, and fixed on frame made up of angle iron incl welding complete all as specified and directed.

Supply and fix Mild steel sliding door bolts of 150mm long bolt, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed with angle iron frame for locking complete all as specified and directed.

Supply and fix Expanded metal weight n-exc 4 Kg/ sqm cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples and fixed complete to wood or steel memberscomplete all as specified and directed by Engr-in-Charge

Cutting holes exc one brick but n.exc two bricks in walls built in cement mortar or cement lime mortar and stone walls built in lime mortar for inserting holdfasts and marking good dismatled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required and directed by Engr-in-Charge.

Material and labour point wiring with 1. 5 Sqmm PVC insulated unsheathed multistranded single core copper conductor cable in PVC surface conduit wiring and incl making good with factory made terminal box (recessed) with 1.5 Sqmm PVC insulated copper conductor earth continuity wire for one light point controlled by one switch.

Description all as per item 43 above but One ceiling fan/Exhaust fan point controlled by one-one way switch through Regulator.

Description all as per item 43 above but One three pin 5 Amp socket on same board with other switches.

Description all as per item 43 above butOne three pin 5 Amp socket on independent board.

Description all as per item 43 above but with 4 Sq.mm. (nominal area) cable for one 3 Pin 15 amp socket on independent board complete all as specified and directed.

Supply and fix switch piano flush, button type 5 Amp SP 250V AC complete all as specified and directed.

Supply and fix switch piano flush button type 15 Amps SP 250V AC complete all as specified and directed.

Supply and fix socket outlet 2-in-1, 5 Pin 5 Amps 250V AC complete all as specified and directed.

Supply and fix socket outlet 2-in1,3 pin 5 and 15 Amp flush type 250V AC complete all as specified and directed.

Supply and fix ceiling rose surface bakelite 3 terminals of size 65x25mm complete all as specified and directed.

Supply and fix LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

Supply and fix BLDC Ceiling Fan complete with electronic type regulator and accessories 230 V,1200 mm sweep. BEE 5 star rated PVC AC single Phase 230 V / 240V 50 Hz of , complete connecting up ceiling rose to connector block of fan including fabricating and fixing of Fan hooks from ceiling truss/angle iron, required length of down rods (Aas per site requirement) and necessary nuts and bolts complete all as specified and directed.

Supply and fix sheet metal enclosures 240 volt 8 way with suitable rated bus bar for Single door IP-43DB's complete all as specified and directed .

Supply and fix MCB SP 240 volt 10 KA 5 to 40 Amp, conforming to relevant IS complete all as specified & directed.

Supply and fix MCB TPN 415 Volt 10 KA 63 Amp conforming to IS complete all as specified and directed.

Material and labour for submain wiring with 3 runs(N+P+E) of 1.5 Sqmm single core,PVC insulated, unsheathed, multistranded copper conductor FRLS cable 1100 volts grade drawn through and including concealed/surface PVC conduit pipe of medium duty not less than 15 mm dia including necessary PVC conduit specials and connecting with suitable size thimble complete all as specified and directed. Note:-3 runs of 1.5 Sqmm size PVC copper cable, and one run of PVC conduit shall be measured as one unit length.

Description all as per item No 58 above, but 3 run of copper conductor FRLS cable 2.5 Sqmm complete all as specified and directed.

Description all as per item No 58 above, but 3 run of copper conductor FRLS cable 4 Sqmm complete all as specified and directed.

Material and labour for earthing complete with galvanised iron earth plate electrode 600 mm x 600 mm x 6 mm thick, burried directly and preferably vertically in ground, earth pit not less than 2.25 m below ground level with top edge of the plate not less than 1.5 m below ground level connetced with galvanised wire 4mm dia by means of nuts, bolts, check nuts and washers made of galvanised iron or steel earthing lead to be protected by galvanised iron pipe 20 mm bore (medium grade) and other end connected to earthing test point or lightening arrestor or main controlling switch all as shown in electrical plate No 3 of SSR Part-I 2009 including providing funnel with 20mm bore galvanised iron pipe (light grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded stone aggregate), 50mm thick precast RCC (1:2:4) type B-1 using 20mm graded stone aggregate cover slab (reinforced with 8mm dia TMT bar @ 15 cm C/C bothways and suitable handle made of 10mm dia), with 40x40x6mm MS angle iron frame including necessary earth work and testing on completion, complete all as specified and as directed.

Supply and Laying XLPE insulated galvanised steel strip or wire armoured elctric power cable with stranded aluminium conductor 1100 V grade of size 35 sqmm 4 core after cutting to required length with necessary glands, nuts, bolts, and lugs complete all as specified and directed

Material and labour for laying brick well burnt Class ‘B’ as cover to U/G cable laid dry flat over the cable with width equal to length of the cable and abutting each other with gap between adjacent slab not exceeding 10mm over under ground cable for cable protection in trenches complete all as specified and directed.

Cutting existing road/hardstand of any type by using crow bar chisel uprto a depthof 30 cm for laying GI pipe including making good the surface by returning filling watering ramming in layers 150 mm thick PCC 1:2:4 type B-2 over 200 mm thick hard core of broken bricks/stones over returning filling watering ramming in layers not exceeding 25 cm thick complete all as specified and directed

Material and labour for GI tubing medium grade (ISI marked) with all fitting/acessories for protection of cable on pole/wall and under road crossing including clamps, nut bolt etc all as specified and directed of size 50mm dia complete all as specified and directed.

Alankar Traders (BID ID -3152280)

M/S JAI PRAKASH GOEL (BID ID -3145665)

M/s Pradeep Kumar (BID ID -3151589)

R K BUILDERS (BID ID -3151121)

VERDHMAN ASSOCIATES (BID ID -3146310)