CERTAIN REPAIRS OF JOINERY AT MD AND OTM ACCN OF SECTOR C UNDER GE (A) BARODA.

Amount

Taking down chowkats or frame with shutters (without taking off shutters from the frame) exc. 1.5 Sqm but n.exc.4 Sqm each

S&F Hand rail, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for chowkhats of doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

S&F 35 mm thick flush shutters, solid core construction, with block board core and both faces covered with decorative face veneer with lipping/frame to match complete all as specified and directed.

S&F in repairs 25mm dia stainless steel tubular curtain rod and fancy type socket fixing with brackets, stop, rollee etc complete all as specified and directed.

Taking down chowkats or frame with shutters (without taking off shutters from the frame) n exc. 1.5 Sqm each

M&L for 18-20mm thick green marble in one piece machine cut as in Door frame, windowcills and like, in cement mortor (1:4) set and jointed in grey cement slurry and pointed in coloured cement (1:2) using marble dust with admixture of pigment to make door frame with marble shade, laid over and including 10mm thick Rendering in cement mortor 1:4 complete all as specified.

Rounding to edges of stone slabs such as door frame and other similar situations complete all as specified

S&F powder coated Anodised frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. power coating (minimum thickness of powder coating 50 micron) complete all as specified and directed.

S&F Powder coated aluminium (minimum thickness of powder coating 50micron) work for doors,windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top,bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle,Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge complete all as specified and directed.

S&F 4mm thick sheet glass ordinary quality and glazing with oil putty in square exc 0.50 Sqm in each pane including Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers complete all as spd and directed. .

S&F Framed work as in doors, windows or gates or grill/grating of angle or other section with gusset plates, rails, braces, etc., complete, drolled for fixing of steel sheeting or other covering. Doors/Windows, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fitting (exclusive of steel sheeting or other covering, running rails and guides) and hanging: also fastening and fixing, conforming to Fe-290 Gde E-165 complete all as specified and directed.

M&L for preparation of new steel or iron surface of any description not otherwise descsribed over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified

Taking down shutters of any description exc. 2 Sqm each complete all as specified and directed.

M&L for 35mm thick 2nd calss hard wood (factory made) glazed and skeleton shutters, open rebated and prerpared to receive glass, gauge, etc edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing , glass etc. sizes of members of shutters as specified in SSR Part-I Section 8.20 (a) complete all as specified.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperature 1.40mm dia and fixed with stainless steel wire staples or with wooden beading.

S&F 125 mm long safety type aluminium anodised hasp and staple with hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

Dismantling timber scantling as in frames of Cup board shelves and equivalent, 40Sqm cm and over in section, in any position complete all as specified and directed.

S&F in repair White/Coloured 18mm thick HDHMR BOARD exterior grade including any coloured prelaminated sheet of required thickness over HDHMR board, anti fungal, moisture resistance, anti borer as per IS 14587 for frame and shutter for kitchen cabinets/cupboards etc all as per specified and directed by Engr-in-charge. Note: sample as approved by GE. Make: Action Tessa/Greenply/Century.

M&L for preparation of new wood and wood based surface of any description not otherwise descsribed over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

S&F Mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate fixed to stone/ concrete choukhats with flat iron 40 x 3 mm size 75cm olng with necessary bolts, etc complete all as specified and directed.

S&F in repair Aluminium (Extruded section) body door closer hydraulically regulated, designation No.3, universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 kg and fixed complete. Make: Dyna and equvalent ISI marked.

Taking down shutters of any description exc. 1 Sqm but n.exc.2 Sqm each

S&F Factory made single extruded WPC (Wood polymer composite) solid door Frame/Chowkhat comprising of 62mmx32mm size applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 KG/Cum and resistance to spread of flame of class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with MS hold fast/SS dash fasteners of required dia and length all as specified and directed.

S&F factory made 28-30mm thick single extruded WPC (Wood polymer composite) solid panel flush door shutter of required size modulus of elasticity 850 N/mm^2 and resistance to spread of flame of class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws complete all as specified and directed.

S&F stainlees steel butt hinges 100mm medium weight complete all as specified and directed.

S&F 300 mm aluminium alloy, anodised sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section.

S&F aluminium alloy handle 150 mm cast type anodised all as specified.

S&F 150 mm aluminium anodised barrel tower bolts of extruded section .

S&F in repair floor door stopper of aluminium alloy body and tongue, overall length of cover plate 140 mm anodised with hard drawn steel spring, fixed in floors complete all as specified and directed.

Demolition of brick work built in cement or cement lime mortor complete all as specified and directed.

M&L for brick work with sub class 'B' bricks straight or curved on plan exceeding 6 mtr mean radius,built in CM 1:6 complete all as specified.

Brick work with sub class 'B' bricks straight or curved on plan exceeding 6 mtr mean radius,built in CM 1:6. but except brick. (Note:-Reusable Bricks retrieved from item No 31 above shall be reused after necessary cleaning etc as directed by Engr-in charge)

Taking down cement plaster from brick/concrete surface including raking out joints hacking for key scrubbing down with water etc complete all as specified .

M & L for 10mm thick rendering in cement mortor 1:6 on brick work or concrete surface of wall, surface finished even and smooth without using extra cement

M & L for preparation of newly plastered surface of wall and applying two coats of Oil bound distemper over and including a coat of 3mm average thick birla/equivalent wall care putty over chalk whiting primer complete all as specified .

S&F 3 mm thick figured glass pin head type and glazing with oil putty in squares not exc 0.5 sqm in each pane complete all as specified and directed

M/s. RAMESH NARHARI VALEKAR

Badri Electricals

Aditya Construction