PROVN OF CHAIN LINK FENCING AT RAMGARH

Amount

Demolition of brick work or stone masonry built in cement mortar including all quions, pillars, pillasters etc. complete all as specified and directed.

Dismantling wrought iron or mild steel work/ structural work incl doors/gates of any description not otherwise provided for, complete all as specified and directed.

Dismantling of CGI/PGI Sheet fixed with screws as in roof covering complete all as specified and directed.

Demolition of cement concrete (Unreinforced) in ground floor and paving n exc 15 cm thick blow or above ground level complete all as specified and directed

Taking down cement plaster on brick / block walling including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Taking down of chowkats or frames not exc 1.5 Sqm each with shutters (without taking of shutters from the frames) including cutting holes for taking out hold fats or dismantling brick work( holes cut and any other damage o jambs , walls for taking out hold fasts shall be finished identical to existing finish without any extra cost to the govt.) complete all as specified and directed

Excavation in trenches n exc 1.50m wide and n exc 1.50m in depth for foundation etc or for shaft wells, cesspits manholes pier holes etc n. exc 10 sqm on plan and n. exc 1.5m in depth and getting out in soft/loose of soil, complete all as specified and directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in hard/dense soil complete all as specified and directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n exc 25cm in depth complete all as specified and directed.

Removing excavated material n exc 50 m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and directed.

M&L PCC 1:3:6 type C-2(40mm gardded aggregate) as in surface channel and drains complete all as specified and directed

M&L providing Cement Concrete M-15, type B-1, 1:2:4 ( using 20mm graded crushed stone aggregate) as in coping, benching, all as specified.

M&L PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified.

M&L PCC 1:3:6 type C-2 (40 mm graded aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

M & L for 75mm thick Plain Cement Concrete 1:4:8, type D-2 using 40mm graded crushed stone aggregate as in sub base of flooring etc for laying floor finishes even and smooth without using extra cement complete all as specified and directed.

M & L for 75mm thick Plain Cement Concrete 1:3:6, type C-2 using 40mm graded crushed stone aggregate as in sub base of flooring etc for laying floor finishes even and smooth without using extra cement complete all as specified and directed.

M & L PCC (1:2:4) type B-0 (Using 12.5 mm graded stone aggregates), as in flooring 25 mm thick. complete all as specified and directed.

M&L PCC 1:5:10 type E-2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified.

M&L Plain cement concrete M-15, nominal mix, type B-1, using 20 mm graded mechanically crushed stone aggregate as in floor, 40mm thick, finished even and smooth without using extra cement complete all as specified.

Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm soft/loose soil complete all as specified and directed.

S&F mild steel work as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc. flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc. and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

M&L for preparation of steel and iron surface exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer complete all as specified and directed.

M&L Preparing surfaces and treating ends of posts, backs of chowkats, etc., area tarred exc 0.1 sq. m but n exc 0.5 sq. m each treated with tar or coal tar black paint, complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provisions of binding wire complete all as specified and directed

Supply only Chain link MS galvanised fencing, any size of type (weight 2.4 Kg/sqm) complete all as specified and directed

Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt n exc 30cm long, diameter of neck n exc 12mm, all as specified.

M & L for MS TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not les than 0.9 mm dia or securing with clips quality conforming to complete all as specified and directed.

M&L TMT bars 5mm to 10mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending spirally for hoping for columns and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, all as specified.

S&F Galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. complete all as directed. Note : (each line of wire to be measured)

M&L black Granite 20mm thick work (table rubbed and polished) in cooking platforms and like in 15 mm thick screed bed of cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M&L RCC M-25 design mix using 20 mm graded stone aggregate in foundations, including rafts, footings, foundation beams, plinth beams, base for columns, etc basements slabs under rammed piles and mass concrete complete all as specified and directed.

M&L RCC M-25 design mix using 20 mm graded stone aggregate in Column, pillars, piers, posts and struts complete all as specified and directed.

M&L RCC M-25 design mix using 20 mm graded stone aggregate as in Beams cantilevers, bressummers lintels over 1.5 m span complete all as specified and directed.

M&L RCC M-25 design mix using 20 mm graded stone aggregate as in slab supported on walls, beams and columns in floors, roofs landings balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Form work to sides of concrete foundations, footings, bases of columns, raft beams sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter complete all as specified and directed.

Form work to sides of pillars, posts, struts, piers, columns and stanchions rough finish surface of concrete square, rectangular or polygonal complete all as specified and directed.

Form work to sides and soffits of floor or roof beam, haunching , lintels, cantilevers shelve including supports overhangs etc also splays between floors and beams, etc complete all as specified and directed.

Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 20 mm thick (horizontal or sloping) complete all as specified and directed.

M&L Brick work with old size bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6, complete all as specified.

M&L Brick work with old size bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4, all as specified.

S&F Providing precast cement concrete louvers and jallies, 35mm thick, type B-0 (1:2:4) 12.5mm graded aggregate, (measured solid), including all mouldings but excluding frame, set in CM 1:4 incl two coats of cement base paint after preparation, complete all as specified as directed by Engr-in- Charge

M&L precast concrete type B-1, 1: 2: 4 (20 mm graded aggregate) as in manhole/septic tank covers slab set in CM 1:4 complete all as specified and directed. Note :- Reinforcement shall be paid seperately under respective items of BOQ.

M&L rendering 10 mm thick in CM 1:4 on fair faces of brick work or concrete surface finished even and smooth without using extra cement complete all as specified and directed

M&L rendering 15 mm thick in CM 1:6 on other than fair faces of brick work or concrete surface finished even and smooth without using extra cement complete all as specified and directed

M&L rendering 10mm thick in CM 1:3 on fair faces of brick work or concrete surface finished even and smooth without using extra cement complete all as specified and directed

Supply only Integral water proofing compound, complete all as specified.

M &L for preapration of newly plastered surface of walls and applying two coats of white wash, complete all as specified and directed.

M &L Preparation of new plastered surfaces and applying two coats of cement base paint in camouflage pattern over alkali resistant priming coat complete all as specified and directed.

M&L for preparation of newly plastered surface of wall any description and applying two coats of oil emulsion distemper over a 2mm thick coat of wall care putty layer on plastered surfaces complete all as specified.

M&L Hard core of broken stone boulders of gauge n exc 63 mm, deposited spread and leveled in layers n exc 15 cm thick, watered and rammed to true surface complete all as specified and directed.

S&F vitrified ceramic dark shade coloured tiles 10mm thick (square/rectangular) polished,area of each tiles n/ exc 0.36 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed in CM 1:6 all as specified and directed

S&F Non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floors set and jointed in neat cement slurry and pointed in coloured cement to match the coloured tiles over 15mm thick screed bed or bedding layer in CM 1:6 for laying finishes,complete all as specified as directed by Engr-in- Charge and approved by GE.

M&L Glazed ceramic tiles, coloured of size 350x250mm/450mm x 350mm/ thickness not less than 7mm as in vertical surfaces such as skirting/dado etc., set and jointed in neat cement slurry and pointed with white or coloured cement, laid over and including 10mm thick bedding layer in cement mortar 1:4 on surfaces of walls complete, all as specified.

M&L for heavy duty coloured chequered cement concrete tiles 30cm x 30cm x 25 mm thick ( As per Sample kept in the office of AGE B/R office) , with grey cement & pigments set, jointed and pointed in neat cement slurry in floors including 15 mm thick screed bed in cement mortar (1:6) and laying floor finishes complete all as specified and directed by Engineer-in-Charge.

M&L for coloured chequered cement concrete tiles 20cm x 20cm x 25 mm thick, with grey cement & pigments set, jointed and pointed in neat cement slurry in floors including 15 mm thick screed bed in cement mortar (1:6) and laying floor finishes complete all as specified and directed by Engineer-in-Charge.

M&L for coloured chequered cement concrete tiles 25cm x 25cm x 25 mm thick, with grey cement & pigments set, jointed and pointed in neat cement slurry in floors including 15 mm thick screed bed in cement mortar (1:6) and laying floor finishes complete all as specified and directed by Engineer-in-Charge.

M&L Plain cement concrete M-10, 1:3:6, type C-1, using 20mm graded mechanically crushed stone aggregate, 50mm thick, as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified. Note:- The unit rate include for use of form work (straight or curved).

S&F Rolled sections as in roof trusses, main and cross beams, hip and jack rafters, Purlins where connected to common rafters and running rails fixed with angle cleats or other connecting plates of Fe-410W (Gde -E-250 quality A) (framed) etc complete all as specified

M&L for preparation of steel and iron surface exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer complete all as specified and directed.

M&L galvalume aluminium zink coating Pre-painted GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ Clading to wall, fixed with self tapping screws as specified complete all as specified and directed.

M&L galvalume aluminium zink coating Pre-painted GI based Plain steel sheet 0.50 mm lthick of an colour having tensile strength of 550 Mpa as in roof covering/Clading to wall, Ridge and eaves board, fixed with self tapping screws as in specified complete all as specified and directed

S&F Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F powder coated aluminium glazed and panelled door with shutter with powder coated aluminium frame of section 83x44x 2mm including 5.5mm thick tinted sheet glass ordinary quality 2 mm thick coloured PVC pannel , 9mm thick ACP sheet with all necessary suitable screw , rubber packing , with all necessary suitable screw, rubber packing, aluminium snap beading complete all as specified and directed.

S&F powder coated Anodised aluminium window and Ventilator side hung shutters type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc., anodised aluminium fittings such as peg stays 150mm long (01 No), hinges type B-21, 100mm long (02 Nos) and suitable size hnadle (01 No) in each shutter, complete all as specified.

S&F 5.5mm thick sheet glass ordinary quality and glazing with oil putty, complete all as specified

S&F aluminium anodised diamond shape grill of size 75mmx75mmx10mm thickk (DG 916, complete all as specified and directed by Engr-in-Charge.

S&F 2nd class hard wood plain framed panelled shutters (any number of panels) with panels of timber flat on both sides(feather edges) or of veneered particle board medium density, wood particle board with commercial face veneers 35mm thick, complete all as specified and directed by Engr-in -Charge

S&F for 30 mm thick 2nd class hard wood glazed and skeleton windows/ventilators shutters open rebated and prepared to receive glass, gauge etc , devide into square with plain chamferred or rounded, mitered and rebated sash bars any numbers , provided with stiles and rails as specified in SSR part I section 8 clause 8.24 (b).

S&F Stairs (framed) conforming to Fe 410-W(Gde-E- 250) quality-A (framed) including stringers, treades, landing, balusters, hand rails etc. including cleats, brackets, etc. complete all as specified as directed by Engr-in- Charge.

M&L 6 mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one face, fixed in ceiling flat and sloping with nails to timber frame complete all as specified and directed

M&L for preparation of new surface and applying two coats of synthetic enamel paint over a coat of pink primer on wooden surface over 10cm width or girth complete all as specified and directed..

S&F 2nd Class soft wood plain fillets square rectangular or triangular in section clean sawn fixed with nails Sectional area exc 13 but not exc 25 sqcm complete all as specified and directed

S & F Solid PVC Door Frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with M S Square tube,supplying and fixing in opening as per manufacturers instructions and as directed by Engineer-in-Charge.

S & F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails .M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail ,lock rail & bottom rail on either side & as gap insert for top rail & bottom rail ; Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/scaled to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement and fixing in the frame as per manufacturers instructions and as directed by Engineer-in-Charge.

S&F aluminium handles, anodised, cast type, of size 150mm complete all as specified and directed

S&F aluminium handles, anodised, cast type, of size 125mm complete all as specified and directed

S&F aluminium anodised barrel tower bolts of extruded section 125mm long complete all as specified and directed

S&F aluminium anodised barrel tower bolts of extruded section 150mm long complete all as specified and directed

S&F butt hinges 100mm long size MS cold rolled medium weight complete all as specified and directed.

S&F butt hinges 75mm long size MS cold rolled medium weight complete all as specified and directed.

S&F aluminium handles, anodised, cast type, of size 150mm complete all as specified and directed

S&F butt hinges 100mm size stainless steel medium weight complete all as specified and directed.

S&F Aluminium alloy, anodised, sliding door bolt size 250 mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolt and sliding bolts of extruded section or cast aluminum alloy and fixed complete all as specified and directed.

S&F 2nd Class Hard wood plain, solid, straight chowkhats and frames wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed.

S&F Vitreous china wash hand basin, with padestal Vitreous china white, flat back, size 550 x 400 mm with brackets, including cutting for and pinning in ends of brackets or erecting stand complete all as specified and directed. (Including 15mm bore CP pillar tap, waste coupling and 32mm dia PVC waste pipe)

S & F 15mm dia pillar taps, cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without lettered 'Hot' and 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F Waste coupling 32mm dia of PTMT (half or full threaded) (Minimum weight 32mm-45gms/40mm-60 gms) all as specified and directed by Engr-in-Charge.

S&F PVC Connection 15 x 450mm size with PTMT Nuts at both ends with rubber washers.complete all as specified and directed.

S&F 32 / 40 mm waste pipe complete all as specified complete all as specified and directed

S&F sheet glass ordinary quality 3mm thick and glazing with oil putty or wooden beads in square n exc 0.50 sqm in each pane complete all as specified and directed

S&F fancy type corner Glass shelf of size 200mmx200mm x 5.5mm thick glasss with CP Railing complete all as specified and directed

Supply, laying, jointing and testing of 15mm bore laid in trenches/ fixed to wall surfaces, galvanized iron steel water tubing medium grade (ISI marked) including provision of all necessary steel fittings/ accessories complete all as specified and directed.

Supply, laying, jointing and testing of 20mm bore laid in trenches/ fixed to wall surfaces, galvanized iron steel water tubing medium grade (ISI marked) including provision of all necessary steel fittings/ accessories complete all as specified and directed.

S&F 15 mm bore bib taps cast copper alloy, chromium plated, fancy type with crutch or butterfly nuts , handle, screwed down for iron pipe for brass ferrule,complete all as specified and directed.

S&F 15 mm bore stop/angle valve cast copper alloy fancy type chromium plated screwed down , high pressure with crutch or butterfly handle, complete all as specified and directed by Engr-in-Charge.

S&F fancy type CP soap dish complete all as specified and directed.

S&F fancy type CP Brass tubular towel rail 20 mm dia & 600 mm long complete all as specified and directed

S&F aluminium anodised tubular towel rail 20 mm dia & 600 mm long 'D' type complete all as specified and directed

S&F CP shower rose of size 125mm dia with shower arm 15mm size, 195 mm long with bend of 45 degree with flange, complete all as specified and directed

S&F Grating square 150 mm with waste hole of PTMT, (Minimum weight 100 gms), all as specified.

S&F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed

S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed

S&F PVC (SWR) junction single, (Single T) equal or unequal, 110mm bore, provided with oval access door all as specified.

S&F PVC (SWR) reducers, 110mm bore, provided with oval access door all as specified.

S&F ‘P’ or ‘S’ trap, 110mm size complete all as specified.

S&F 75mm PVC (SWR) vent cowl, all as specified.

PVC (SWR) bends 110mm bore complete all as specified and directed

PVC (SWR) bends 75mm bore complete all as specified and directed

S&F vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including connections of flush pipe to squatt pattern closet including lime concrete bedding and all joint making good to the floor all as specified.

S & F vitreous china wash down water closet pan "Pedestal" coloured including fixing bolts etc including PVC seat cover white with flat bottom including MS, CP or aluminium anodised hinge devices with all internal fitting, inlet, outlet pipe connections etc complete all as specified and direcrted.

S&F health faucet CP Brass hand Jet Shower 15mm bore dia and 1000mm long CP pipe complete all as specified and directed by Engr-in-Charge.

S&F 10 lit PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet,ball valve, float and handle including brackets, complete all as specified and directed by Engr-in -Charge.

Construction of Septic Tank 25 user, excavation in any type of soil, foundation PCC, brick work in CM 1:4 , RCC/CI man hole covers, Vent shaft and sludge chambers etc complete all as specified and shown in drg directed by Engr-in-Charge. Drg No CESZ/TD-01/2015 Sheet 1/3, 2/3

Construction of soakage well for users, excavation in any type of soil, foundation PCC 1:3:6 wells of honey combed and solid in M-25 concrete, including intercepting chamber screen chamber, brick work CM 1: 4, RCC cover slab in M-25/ RR masonry filling with brick bats, complete of size 1.20 m dia 3.0 m deep as shown in drg complete all as specified and directed by Engr-in-Charge. Drg No CESZ/TD-01/2015 Sheet 3/3

S&F for Rotational moulded polythylene 1000 litres capacity water storage tank (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position including 20 mm ball valve high prressure of PTMT with epoxy coated alu rod & high density plastic ball, complete all as specified

S&F 20mm bore Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed, complete all as specified

S&F in repair Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), (half stall type, white), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe, complete all as specified.

S & F vitreous china wash hand basin, counter sunk type of size 550x400mm , PVC waste coupling 32mm, chain and plug and PVC waste pipe, PVC connection 45cm long including CI brackets/fixing with fasteners etc complete in repairs all as specified and directed by Engineer-in-Charge.

S & F 15 mm bore brass CP mixer for mixing hot and cold water screwed down high pressure with long screwed shanks and fly nuts screwed for iron pipes

Supply, fixing, jointing and testing, ISI Marked, of approved quality, gun metal globe/gate valve 20mm dia with iron wheel head, both ends screwed for iron pipe complete all as specified and directed.

Rough excavation not exc. 1.5 metres in depth in any type of soil complete, all as specified.

Walling random rubble masonry with best stone, uncoursed, well bonded, bedded, solidly hearted and built in cement mortar 1:6 (1 cement : 6 coarse sand), all as specified. Note: Locally available slate stone shall not be used. (If PCC bond stone used in lieu of stone bond, the same shall be measured and paid separately and deduction shall be made for using PCC bond stones).

M&L Cement concrete M-15, type B-1, 1:2:4 ( using 20mm graded crushed stone aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating and necessary form work, all as specified.

M&L Precast cement concrete type 1:3:6 ( 16mm graded stone aggregates), hollow block masonry exc. 10 cm in width and setting in mortar complete setting in mortar Set in cement mortar 1:4, complete all as specified and directed.

M&L Brick work with old size bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:4, complete all as specified.

M&L rendering 15 mm thick in CM 1:4 on fair faces of brick work or concrete surface finished even and smooth without using extra cement complete all as specified and directed

Taking down carefully aluminum/copper point wiring (light fan socket or power) complete with fitting such as switches, tube lights, ceiling rose, pendants, regulators, MCB DB, MCB'S, Main switch from control board and making good disturbed surfaces of walls, floor to match with existing specification complete and all as specified keeping aside regulators/ light fitting/ MCBs all as specified and directed.

Point wiring for one light point/fan point controlled by one switch with 1.5 sqmm PVC FRLS insulated unsheathed copper conductor single core multi strand flexible cable and 1.5 sqmm PVC insulated unsheathed copper conductor single core cable (green color) as earth lead in and including PVC casing and capping/Conduit medium grade of suitable size run on wall/surface with all fittings (ISI Marked) controlled by one switch including CI/MS sunk box of required size or PVC Gang Box all as directed by Engr in Charge & 3mm thick plastic laminated sheet, including cutting chases to wall making good the disturbed surfaces to match with the existing specification complete all as specified. .

All as per srl item No-130 here in above but for one 3 pin 5A socket outlet independent controlled by one switch.

All as per srl item No-130 here in above but for one 5A socket outlet on the same board controlled by one switch.

All as per srl item No-130 here in above but for one 3 pin 15 Amps socket outlet independent with 2.5 sqmm PVC insulated unsheathed copper conductor single core multi strand flexible cable and 2.5 Sqmm PVC FRLS insulated unsheathed copper conductor single core cable (green color) as earth lead.

M&L for switch piano flush button single pole one way 5 amps 240 volts.

M&L for Switch Socket combination 2 in 1, 5 pin, 5 Amps flush type, 230 volts.

M&L for socket out let, 6 pin 5 and 15 amps multi purpose 2 in 01 flush type, 230 volts.

S & F Lamp holder angular/straight insulated body with back plate for batten fittings.

Supply & fixing ceiling rose, 3 phase/PVC/polycarbonate isolated body complete all as specified & directed by Engineer -in- Charge.

S&F decorative ultra slim linear LED in replacement of 20 Watt , 4 ' long lighting fixture with extruded Al heat sink , environment friendly , energy efficient ready to use pack incl LED tube complete with inbuilt electronic driver , PCB , connector block etc including connecting up with three core twisted flexible copper conductor cable with suitable size LED tube all as specified and directed by EIC. Make : Havells Cat Part No LHDD02102674 or Equivalnet/C&S/Bajaj.

Supply and fix LED Bulk Head light fitting ,System consumption should be between 6-10W. Similar to Philips Cat No : WT202W LED 6S NW PSU S2 PC or Havells cat part No RUGBYNE ONFT 10W LED 760 SSYMBOPC

Supplying and fixing in repair recess mounted 18 W LED pressure die- cast aluminium luminaries in powder coated white finish in round profile with optimized heat sink for efficient heat dissipation and separate replaceable electronic driver, including provision of fixing in ceiling with all items required for fixing all as specified and directed by Engr-in-Charge Make:- Havells Items description NEODLR18WLED857S HSN Code 9405 or equivalent in Phillips/Bajaj

Supply and fixing MCB Distribution board , 240 volts single pole and neutral ,double door, sheet steel, enclosure powder coated with 200 Amps rated copper busbar with neutral link, 4 ways , fixed on wall duly grouted in solid block wall or on wooden board with electrical connection incl taking down existing DB, complete all as specified and directed.

Supply & fixing in repair sheet metal enclosure MCB distribution board Single pole & neutral 240 volts 8 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification .

Supply and fixing MCB, SP, AC, 240 volts "B" series capacity of 06 to 32 Amps, 10kA and making connections complete all as specified & directed.

Supply & fixing MCB, DP (Double Pole), AC, 240 volts, B series capacity 05 Amps to 32 Amps, 10kA and making connections complete all as specified & directed .

Earthing complete with galvanised steel earth plate electrode 60 cm x 60cmx6mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 meters below normal ground level. connecting to the GI wire 4 mm dia by means of bolls, nuts, check nuts and washers of galvanised iron and earth wire protected by provision of GI light grade pipe 15mm bore including provision of concrete pit in PCC (1:2:4) type B-1 using 20mm graded stone aggregates with 40mm thick cover of RCC (1:2:4) reinforced with XPM weight not less than 4 Kg/Sqm) and frame of angle iron 25x25x6mm with lugs 02 Nos and handle of 6mm dia MS bar made to shape, GI medium grade 20mm bore pipe for watering , perforated at bottom. 1.75 metre long placed on top edge of earth plate. charcoal and common salt filling with fixing arrangement, funnel wire mesh and earth work in soft soil returning filling in and removal of surplus soil to a distance not exceeding 50 meters all as per electrical plate 3 of SSR-2009 Part-I and connecting to earth test point all as specified or indicated including testing on completion. NOTE :- (i) Item of earthing includes cost of 7.5 m long GI wire of size 4 mm dia with protection pipe of 15mm dia GI medium grade, any variation in length shall be adjusted through deviation order based on SSR rates enhanced by 25%. (ii) On testing after completion of earthing if the desired earth resistance is not obtained earthing will be re-done by the contractor at his own risk and cost.

Supply and fixing exhaust fan 230 mm sweep PVC body with louvers, 240 volts AC single phase, 50 Hz, ISI marked, including necessary work in wall/sheet, including connection cable of suitable size, nut bolt and other fixing material complete all as specified and directed by Engr-in-Charge.

Supply and laying or fixing or passing through pipe or binding with fencing/pole etc, 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 10 Sq mm nominal cross section 2 core all as specified and directed by engr-in-charge.

M/S Sofi Brothers

M/S HAMID AND CO

JANDOO AND CO.

M/S LATIF AHMAD BABA CONSTRUCTION

M/s M Ashraf and Brothers

M/S AK ENTERPRISES

M/S KASHCON CONSTRUCTION CO