Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹1.2 LAccepted-AOC | L1 | Accepted-AOC Accepted Vide Resolution No.3(2) dtd.15/05/2023 Mathur GP | |
| 2 | L2₹1.3 L+₹10,151 (8.33%)Rejected-AOC | L2 | Rejected-AOC Higher rate hence rejected |
Tender Value
₹1.0 L
EMD Value
₹2,539
Closing Date
30 Dec 2023, 5:00 pmClosed
ASSISTANT ENGINEER,MATHUR GP
OFFICE OF ASSISTANT ENGINEER, LIDEW SECTION, MATHUR GP, MATHUR (P.O) PALAKKAD PIN CODE 678571
MAINTENANCE OF THANNERANGAD ANGANWADI IN MATHUR GP
2023_LSGD_634871_1
97/2023/AE/LSGD/MTR
Open Tender
Civil Works - Buildings
Item Rate
320 days
MATHUR GP
Please refer Tender documents.
7 documents required · 7 mandatory
₹555
Yes
₹2,539
Yes
24 Sept 2024
22 Dec 2023
4 Jan 2024
22 Dec 2023
30 Dec 2023
22 Dec 2023
Amount
Sheet work
10.16.1:Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes
12.50:Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)
50.6.1.5:Solid block masonry using pre cast solid blocks ( Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 Part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete
13.7.1:12 mm cement plaster finished with a floating coat of neat cement of mix:1:3 ( 1 cement : 3 fine sand)
LAL KISHEN.R
Bidder Name
HARIDAS K
LAL KISHEN.R
tech_eval.pdf
fin_eval.pdf
aoc.pdf
finance_963506.pdf
boq_comp_chart.xlsx
xlsx
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .