Construction of vehicle garage for 9 Nos of Magistrate Qtr Partition wall alongwith 1 toilet construction in the double room of 2nd floor Circuit House concrete base and shed for DG set Udalguri DCs Complex in Udalguri District_TN_92_1

Amount

(A) Cost of Garrage 9 Nos.: 1.1 Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completetion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. A) Up to a depth of 2.00m below the existing ground level. (a) In ordinary soil

4.1.1. Providing soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete. (a) Brick on flat Soling

2.1.1. Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing stepts, walls brick works etc. as directed and specified including dewatering if necessary and curing complete (Shutering where necessary shall be measured and paid separately) (a) In prop 1 cement : 3 sand : 6 coarse aggregate by volume

18.1.1. Supplying, fitting and fixing in position reinforcement bars conforming to relevent I.S. Code for R.C.C. work/R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20 G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete (No extra measurement for lap, hook, chair, anchpr etc. will be entertained in the measurement as they are included in the rate) (Upto Ist floor level) (a) Super Ductile (SD) TMT reinforcement bars.

18.1.1. Supplying, fitting and fixing in position reinforcement bars conforming to relevent I.S. Code for R.C.C. work/R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20 G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete (No extra measurement for lap, hook, chair, anchpr etc. will be entertained in the measurement as they are included in the rate) (Upto Ist floor level) (c) ISI approved Mild Steel reinforcement bar (M.S. Bar) (a) 6mm dia

3.2.1.Providing form work of 12mm thick plywood board so as to give a rough finish including centering shuttering, strutting and propping etc. 3.2.1.1. Column, pillars posts & struct of square/rectangular/ Polygonal in plain ar any shape like Tee/ L etc.

3.2.1.2.Providing form work of 12mm thick plywood board so as to give a rough finish including centering shuttering, strutting and propping etc. 3.2.1.2. : Sides and soffits of beam, beam haunchings, cantilever girders bressumers, lintels and horizantal ties. a) For depth not execeding 1.00 M

2.2.1. Providing and laying plain/reinforced cement concrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinfor cement for reinforced cement concrete work (from work and reinforcement will be measured and paid separately) (I) Using Mixture Machine (A) Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. (N) Without using admixture, plasticiser (b) M20 grade concrete or prop. 1:1.5:3

2.2.1 Providing and laying plain/reinforced cement concrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (from work and reinforcement will be measured and paid separately) (b) In super structure from plinthlevel upto Ist floor level. ii) Columns, pillars, posts, struts, suspended floor, roof, landing, shelf and support, belcony, lintel, sill band, beam, girder, bressumer, cantilever, staircase (exceptspiral staircase and landing) including preparing the top surface and finishing of nosing. (N) Without using admixture, plasticiser (b) M20 grade concrete or prop. 1:1.5:3

4.1.4. Brick work in cement mortar with Ist class brick including racking outjoints and curing complete as directed. (i) In sub-structure upto plinth level including dewatering if necessary b) In prop. 1:4

1.3. Earth/ sand filling in plinth layers not more than 150mm thick including necessary carriage, watering, ramming etc. complete as directed and specified including payment of land compensation, forest royalty, sales tax and other duties and taxes as may be necessary. (c) With river sand or silt (predominantly non plastic) by truck carriage including loading and unloading

2.1.3. Providing and laying 25mm thick damp proof course with cement concrete in prop. 1:1.5:3 with graded stone agg. of 10mm down nominal size including providing approved damp proof admixture in proportion as recommended by the manufacture including curing etc. complete as directed.

4.1.8. Ist class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth upto Ist floor level (protruding M.S. rod/Tor steel of column to be embeded in cement mortar and will be measured and paid separately) A) 112mm thick brick wall (a) In cement mortar in proportion 1:4 (1 cement : 4 sand)

18.3.2. Providing, fitting, hoisting and fixing of roof trusses fabricated using any one or combination of following section of (i) Square (ii) Rectangular Hollow section of specification SHS/RHS and including purlins, bottom runners and providing M.S. cleat, M.S. angle base plank, bolts and nut with red oxide primer including fitting bottom runner and cleat etc. for fixing ceiling joist as per design complete as directed as per specifications. (b) Using other ISI marked approved barnd tube 1) 60.30 OD (H) Black tube

8.1.35. Providing pre painted galvalume sheet roofing (P.P.GL) at all levels including fitting and fixing self drilling, self tapping screws complete ( Roof trusses, purlin etc. to be measured and paid separately) Tata Blue scope/Dyna roof/Wonder Roof or equivalent as directed by the department. (iv) 0.60mm thick

9.4.1. Providing barge board of size 200mm x 25mm with Ist class wood Hollock/Bonsum timber including fitting and fixing with necessary wood screws etc.... complete

6.2.2. 15mm thick cement plaster in single coat on single or half brick wall for interior plastering upto Ist floor level including arise, internal roundred angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. A) On rough side b) In cement mortar 1:4

6.2.2. 15mm thick cement plaster in single coat on single or half brick wall for interior plastering upto Ist floor level including arise, internal roundred angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. B) On fair side b) In cement mortar 1:4

5.1.4. 65mm thick cement concrete floor consisting of 50mm under layer of cement concrete in prop. 1:3:6 (1 cement : 3 coarse sand : 6 coarse aggregate of 25mm and down) and 15mm thick wearing layer in cement concrete in prop. 1:1:2 ........ complete as directed.

19.3. Providing plinth protection with brick flat laid in cement mortar 1:4 and finished 15mm thick cement plaster in prop. 1:2 with a flating coat of neat cement finish.

13.2.3.(a) Applying one coat of cement primer of approved brand and manufacture on new wall surface after throughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth.

13.2.3.(b) Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on new walls surface (two coats) to give an even shade after throughly brooming the surfaces to remove all dirt and remains of loose powdered materials.

26.1.1. Pre-construction anti terment at the bottom of foundation pits … a) Column , trench

26.1.2. Pre-construction anti terment ….. a)

26.1.3. Pre-construction anti terment treatment by applying in the entire ... a) area

(B) Cost of DG Shed: 1.1. Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completetion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. A) Up to a depth of 2.00m below the existing ground level. (a) In ordinary soil Post , Wall

4.1.1.Providing soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and material sand if necessary dewatering, complete. (a) Brick on flat Soling

2.1.1. Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing stepts, walls brick works etc. as directed and specified including dewatering if necessary and curing complete (Shutering where necessary shall be measured and paid separately) (a) In prop 1 cement : 3 sand : 6 coarse aggregate by volume

18.1.1. Supplying, fitting and fixing in position reinforcement bars conforming to relevent I.S. Code for R.C.C. work/R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20 G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete (No extra measurement for lap, hook, chair, anchpr etc. will be entertained in the measurement as they are included in the rate) (Upto Ist floor level) (a) Super Ductile (SD) TMT reinforcement bars.

18.1.1. Supplying, fitting and fixing in position reinforcement bars conforming to relevent I.S. Code for R.C.C. work/R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20 G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete (No extra measurement for lap, hook, chair, anchpr etc. will be entertained in the measurement as they are included in the rate) (Upto Ist floor level) (c) ISI approved Mild Steel reinforcement bar (M.S. Bar) (a) 6mm dia Post, tie beam and Cap beam

3.2.1. Providing form work of 12mm thick plywood board so as to give a rough finish including centering shuttering, strutting and propping etc. 3.2.1.1. Column, pillars posts & struct of square/rectangular/ Polygonal in plain ar any shape like Tee/ L etc.

3.2.1. Providing form work of 12mm thick plywood board so as to give a rough finish including centering shuttering, strutting and propping etc. 3.2.1.2. : Sides and soffits of beam, beam haunchings, cantilever girders bressumers, lintels and horizantal ties. a) For depth not execeding 1.00 M

2.2.1. Providing and laying plain/reinforced cement concrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinfor cement for reinforced cement concrete work (from work and reinforcement will be measured and paid separately) (I) Using Mixture Machine (A) Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection … (N) Without using admixture, plasticiser (a) M15 grade concrete or prop. 1:2:4

2.2.1. Providing and laying plain/reinforced cement concrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinfor cement for reinforced cement concrete work (from work and reinforcement will be measured and paid separately) (I) Using Mixture Machine (B) In super structure from plinthlevel upto Ist floor level. ii) Columns, pillars, posts, struts, suspended floor, roof, landing, shelf and support, belcony, lintel, sill band, beam, girder, bressumer, cantilever, staircase (exceptspiral staircase and landing) including preparing the top surface and finishing of nosing. (N) Without using admixture, plasticiser (b) M15 grade concrete or prop. 1:2:4

4.1.4. Brick work in cement mortar with Ist class brick including racking outjoints and curing complete as directed. (i) In sub-structure upto plinth level including dewatering if necessary b) In prop. 1:4 Wall, Step.

1.3. Earth/ sand filling in plinth layers not more than 150mm thick including necessary carriage, watering, ramming etc. complete as directed and specified including payment of land compensation, forest royalty, sales tax and other duties and taxes as may be necessary. (c) With river sand or silt (predominantly non plastic) by truck carriage including loading and unloading

18.3.2. Providing, fitting, hoisting and fixing of roof trusses fabricated using any one or combination of following section of (i) Square (ii) Rectangular Hollow section of specification SHS/RHS and including purlins, bottom runners and providing M.S. cleat, M.S. angle base plank, bolts and nut with red oxide primer including fitting bottom runner and cleat etc. for fixing ceiling joist as per design complete as directed as per specifications. (b) Using other ISI marked approved barnd tube

18.1.35.Providing pre painted galvalume sheet roofing (P.P.GL) at all levels including fitting and fixing self drilling, self tapping screws complete ( Roof trusses, purlin etc. to be measured and paid separately) Tata Blue scope/Dyna roof/Wonder Roof or equivalent as directed by the department. (iv) 0.60mm thick

6.2.2. 15mm thick cement plaster in single coat on single or half brick wall for interior plastering upto Ist floor level including arise, internal roundred angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. A) On rough side b) In cement mortar 1:4

5.1.4. 65mm thick cement concrete floor consisting of 50mm under layer of cement concrete in prop. 1:3:6 (1 cement : 3 coarse sand : 6 coarse aggregate of 25mm and down) and 15mm thick wearing layer in cement concrete in prop. 1:1:2 ........ complete as directed.

9.4.1. Providing barge board of size 200mm x 25mm with Ist class wood Hollock/Bonsum timber including fitting and fixing with necessary wood screws etc.... complete

19.3. Providing plinth protection with brick flat laid in cement mortar 1:4 and finished 15mm thick cement plaster in prop. 1:2 with a flating coat of neat cement finish.

13.2.3. (a) Applying one coat of cement primer of approved brand and manufacture on new wall surface after throughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth.

13.2.3. (b) Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on new walls surface (two coats) to give an even shade after throughly brooming the surfaces to remove all dirt and remains of loose powdered materials.

(C) Cost of Partition wall along with 1 (one) Toilet: 23.18.Dismentaling and removing the existing door and windows frame (chowkath) both wooden and steel of different size .. (i) Area of door/window upto 3.00 m2

23.16. Demolising mosai of various thickness both mosiac tiles and cast in-situ type including C.C. base course and removal of debris as directed for all levels

18.1.1. Supplying, fitting and fixing in position reinforcement bars conforming to relevent I.S. Code for R.C.C. work/R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20 G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete (No extra measurement for lap, hook, chair, anchpr etc. will be entertained in the measurement as they are included in the rate) (Upto Ist floor level) (a) Super Ductile (SD) TMT reinforcement bars.

3.2.1. Providing form work of 12mm thick plywood board so as to give a rough finish including centering shuttering, strutting and propping etc. 3.2.1.2. : Sides and soffits of beam, beam haunchings, cantilever girders bressumers, lintels and horizantal ties. a) For depth not execeding 1.00 M

2.2.1. Providing and laying plain/reinforced cement concrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinfor cement for reinforced cement concrete work (from work and reinforcement will be measured and paid separately) (I) Using Mixture Machine (A) Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. N) Without using admixture, plasticiser b) M20 grade concrete or prop. 1:1.5:3

4.1.8 Ist class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth upto Ist floor level (protruding M.S. rod/Tor steel of column to be embeded in cement mortar and will be measured and paid separately) A) 112mm thick brick wall (a) In cement mortar in proportion 1:4 (1 cement : 4 sand)

9.1.2. Providing wood work in frame (Chowkaths) or doors, window, clerestory windows and other similar works rough finished framed fixing in position in contact with C.C. brick, necessary wall etc. etc. complete specified. (b) With Ist class local wood Hollock/Bonsum

9.9.3. Providing, fitting and fixing factory made wonder panelled door with panel inserts of 75mm to 50mm width and 12mm to 20mm thick …. Etc. b) With Ist Class local wood (Hollock/Gamari/Sundi/Bonsum ii) 35mm thick

9.9.7. Providing and fitting fully glazed window with sash bars including oxidised M.S. bult hinges (75mm x 60mm x 3.15mm) 2 nos on each leaf and 3 nos on single left … etc. b) With Ist Class local wood (Hollock/Gamari/Sundi/Bonsum ii) 35mm thick

16.1. Providing and fixing cleare sheet glass beded in putty and fixed with/without wooden bidding including necessary cutting and glass be required sized.. Etc. b) Area of glass panes not execluding 0.15m2 a) 3.00mm thick

6.2.2. 15mm thick cement plaster in single coat on single or half brick wall for interior plastering upto Ist floor level including arise, internal roundred angles, not exceeding 80mm girth and finished even and smooth including ...as directed. A) On rough side b) In cement mortar 1:4

1.3. Earth/ sand filling in plinth layers not more than 150mm thick including necessary carriage, watering, ramming etc. complete as directed and specified including payment of .............as may be necessary. (c) With river sand or silt (predominantly non plastic) by truck carriage including loading and unloading

4.1.1 Providing soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materialsand if necessary dewatering, complete. (a) Brick on flat Soling

5.1.4. 65mm thick cement concrete floor consisting of 50mm under layer of cement concrete in prop. 1:3:6 (1 cement : 3 coarse sand : 6 coarse aggregate of 25mm and down) and 15mm thick wearing layer in cement concrete in prop. 1:1:2 ........ complete as directed.

5.7.2.1. Providing VITRIFIED floor tiles of approved quality of specified size, shape and thickness not less than 18mm on floor, skirtings, risers and treads of step over 15mm thick base of cement mortar in prop. 1:3 etc. (I) Normal range (Somany/orient/Nitco varmora/Jhonson make. (a) of size 600mm x 600mm and above

5.7.2.2. Providing Polish vitrified wall tiles of approved quality size shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10mm thick in prop. 1:3 including cutting where necessary finished .. Etc. (iii) of size 300mm x 600 mm and above

4.1.14. Extra for brick walling for each subsequent floor or part thereof above the Ist floor level a) 112mm thick brick/R.B. Wall

6.2.4. Extra over item no 6.2.1. to 6.2.3 for providing and mixing water proofing materials in cement mortar in prop as recommended by the manufacture including curing complete a) 15mm thick plaster (b) In prop. 1:4

13.3.1. Providing surface preparation for walls, ceiling etc. using average 1.5 mm thick plaster of pairs including cleaning rubbing ……

13.4.1. Wall painting (two coat) with arylic emulsion paint approved brand and manufacture (Asian paint, Berger, ICI Paint/J&N Paint/Nerolac) on new surface to give and even shade after througly brushing the surface.. Etc.

13.6.3. Applying priming coat over new wood and wood based surfaces over 100mm in girth/ width after and including preparing the surface throughly cleanning oil, grease, dirt and other foreign matter, sand papering and knotting. b) With ready mixed paint wood primer white.

13.6.5. Painting two coats (excluding priming coat) on new wood and wood based surface with enamel paint of approved brand and manufacture (Asian paint, Berger, ICI Paint/J&N Paint/Nerolac) to give and even shade including cleaning the surface of all dirt and dust, other foreign matter, sand papering and topping (i) Surface over 100mm in width or girth (b) High gloss (Asian Paint/Berger paint/ICI paint))

Sanitary and Water Supply 1.3. Providing fitting and fixing vitreous china wall hang water closet(European type W.C. pan 400mm high) with seat and pead, CP brass hings and rubber buffers CI/MS brackets 40mm dia flush band….. etc. etc. complete a) Parryware make a) Pal wal vit pan (inclusive of seat cover and fitting (White/Coloured) (Cat No. C844K)

1.13. Providing vitreous wash basin with CI/MS bracket, CP brass chain with plug, PVC waste Pipe including painting of fittings and brackets cutting and making good the walls, whatever required (Aillar cock, stop cock, waste cenpling are to be paid separetely) 1.13.2. Basin (Without Pedestal) A) Parryware Make a) White i) Duke 660 x 495 (Cat No. C8416/27) (White/coloured)

1.19. Providing fitting and fixing Decorative Mirror complete as directed and specified A) Parryware make (a) Size 800mm x 600mm

1.21. Providing fitting and fixing recessed soup tray soup dish complete as directed. a) Parryware (i) Recess SP&SG dish (Cat No. C9935)

1.24. Providing fitting and fixing C.P towel rail complete as directed and specified. A) Jaquar make (iii) Queen's (600mm long) (Cat No. AQN-7711)

1.37.2. Supplying fitting and fixing 87.50 degree PVC bend of (Supreme/prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all level… etc. a) In exposed surfaces or intrenches ii) 110mm dia

1.37.2. Supplying fitting and fixing 87.50 degree PVC bend of (Supreme/prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all level… etc. a) In exposed surfaces or intrenches iv) 75mm dia

1.37.5. Supplying fitting and fixing PVC plain single tee of (Supreme/prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete. a) In exposed surfaces or intrenches ii) 110mm dia

1.37.14. Supplying fitting and fixing PVC reducer of (Supreme/prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete. a) In exposed surfaces or intrenches ii) 110mm x 90mm dia

1.37.17. Providing fitting and fixing PVC Sockets Plug of (Supreme/prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete. a) In exposed surfaces or intrenches ii) 110mm x 90mm dia

1.39. Providing fitting and fixing PVC Cowel of ISI make complete as directed and specified. ii) 110mm dia PVC cowel of ISI make

1.387.1.Supplying fitting and fixing gun metal country pit valve (full way valve

3.1.1. Supplying, fitting and fixing G.I. pipes of following sizes with all necessary 'R" brand or similar approved G.I. fitting such as bend, tee, elbow reducer, nipple plug long screw fittings etc. (A) Eeposed on walls b) 25mm dia (Mediam) (i) Using Tata make

3.1.1. Supplying, fitting and fixing G.I. pipes of following sizes with all necessary 'R" brand or similar approved G.I. fitting such as bend, tee, elbow reducer, nipple plug long screw fittings etc. (A) Eeposed on walls d) 15mm dia (Mediam) (i) Using Tata make

3.2.1. Supplying fitting and fixing C.P. bib cock 15mm dia of approved brand as directed and specified…. (G.I. & CP pipes will be measured separetly) (ii) Jaquare make (ii) Bicock long thread (i) Standard

3.3.2. Supplying fitting and fixing chrome plated (C.P.) Stop cock of approved brand and size as mentioned below as directed … etc. (ii) Jaquare make (ii) 15mm dia (Angular stop cock)

3.8.1. Supplying fitting and fixing overhead adjustable chrome plated (C.P.) spray shower 15mm dia at sona make .. Etc. (a) Supreme shower with arm b) Apex/Kiran/Priya/Star… etc.

3.17.1. Supplying fitting and fixing gun metal country pil valve (full way valve) ISI make as directed b) 40mm dia

5.1.1. Supplying fitting and fixing pipes with all necessary fitting in exposed or in trenches including trenching and refilling the sum etc. (A) G.I. pipe with GI fitting a) TATA/SAIL (Medium) (iii) 25mm dia meter ix) 100 mm dia meter

5.3.6. Supplying fitting and fixing section pipes plain/bevel ended conforming to relevent IS codes of practice including supplying and fitting of accessories etc. A) G.I. Pipe (iii) 40mm dia meter

(D) Cost of C.C. Pavement: 30.1. Construction of Sub-grade and earthen shoulder with approved materials obtained from borrow pit, with all lifts & leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2 (including compensatin of earth) (including cost of testing of materials at site and laboratory as directed by the deptt.) b) From Government land 1. Layers of 0.45m Thickness

30.2. Construction of Granular sub-base providing close material, spreading in uniform layers with motor grader on prepared surface mixing by mix place method .... etc. etc. as directed by the deptt. (ii) Using Grading -II material

18.1.1. Supplying, fitting and fixing in position reinforcement, bars conforming to relevant I.S. Code for R.C.C. work/R.B. walling including staightening cleaning, cutting and bending to proper shape and length as per details ... etc. complete. (ii) Other ISI marked approved brand Considering 8mm dia @ 150 C/C

30.4. Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering etc...... complete. (ii) Using 25mm thick planks.

30.5. Providing and laying controlled cement concrete pavement of approved grade with 20mm down graded stone aggregate etc.. complete. (I) M20 Grade Concrete.

Sri Ransingh Daimari

Bapan Ch Boro