NIT NO:995/TC/2026-27

Excavation for all types and sizes of foundations, trenches and drains or for any other purpose including disposal of excavated stuff upto 1.5 m lift and lead upto 50m (at least 5m away from the excavated area), including dressing and leveling of pits. In all types of soils.

Extra for every additional lift of 1.5 m or part thereof All kinds of soil

Filling from available excavated stuff (Excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering with a lead upto 50 M. and lift upto 1.5 M.

Providing and filling in plinth with sand/ Crusher dust and hard moorum under floor in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering, including dressing etc. complete.

Supplying chlorpyrifos/ Lindane emulsifiable concentrate of 20% in sealed containers including delivery as specified.

Diluting chemical emulsion (chlorpyrifos/ lindane) in water as per manufacturers recommendation and injecting for post - constructional ani- termite treatment (excluding cost of chemical emulsion): Along external wall below concrete or masonry apron along the plinth wall using diluted chemical emulsion @ 0.65 litres per hole including drilling 12mmdia holes 300mm apart and plugging the same with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing apron after injecting chemical emulsion.

Diluting chemical emulsion (chlorpyrifos/ lindane) in water as per manufacturers recommendation and injecting for pre-constructional curative cum preventive anti-termite treatment:(Five year service guarantee bond to be signed by contractor) Surface treatment by spreading emulsion under floor, over the plinth area before laying base concrete @ 5 litres / sqm

Treatment of inside of plinth masonry wall on using diluted chemical emulsion @ 1.5 litre per hole, including drilling 12 mm diameter holes in plinth wall below plinth protection at the interval of 300 mm and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand).

Treatment of outer side of plinth masonry wall using diluted chemical emulsion @ 1.5 litre per hole, including drilling 12 mm diameter holes in plinth wall at the junction of floor at the interval of 300 mm and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand).

Carriage by mechanical transport upto 5 km lead: Dismantled Building debris (Mulba)

Providing and laying nominal mix plain cement concrete with crushedstone aggregate using concrete mixer in all works upto plinth levelexcluding cost of form work. 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources).

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 12.5mm nominal size)

Providing and fixing aluminium strip 1.60 mm thick on expansion joints with iron screws as per design to match the colour, shade of wall treatment .

Providing and fixing in expansion joint pre moulded cross linked polymer based filler as per IS:1838 (part III) of approved make including cutting to required size and shape etc complete. 50 mm thick

Providing and laying design mix reinforced cement concrete with crushed graded stone aggregate 20mm nominal size using batching plant, transit mixer and concrete pump, in all works upto plinth level excluding cost of form work. M-25 Grade

Providing and laying design mix reinforced cement concrete with crushed graded stone aggregate 20mm nominal size using batching plant, transit mixer and concrete pump, in all works upto plinth level excluding cost of form work. M-30 Grade

M-25 Grade Ground Level

First Level

Second Level

Providing and placing in position reinforcement for R.C.C. work including straightening, cutting, bending, binding etc. complete as per drawings including cost of binding wire all complete: Thermo mechanically Treated bars of grade Fe 550D or more.

Applying a coat of hot bitumen VG-10 using @ 1.7kg/ sqm on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Dry Lean Cement Concrete Sub- base Construction of dry lean cement concrete Sub-base as per IRC:SP-49 over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 26.5 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 tonnes vibratory roller, finishing and curing as per clause 601.

Providing and laying Un-reinforced Cement Concrete without Dowel bars including formwork and expansion, contraction & longitudinal joints as per design and as per IRC-62, over a prepared base a per approved mix design and finising to lines and grade as per Drawing for Pavement thickness less than 200mm in Low Volume Roads. With Cement concrete grade M-30 and minimum cement content @ 375 kg/cum

Providing and fixing form work including centring, shuttering, strutting, staging, propping bracing etc. complete and including its removal at all levels, for: Foundations, footings, bases of columns plinth beam, curtain wall in any shape and size and all type of wall below plinth level.

Wall of any thickness including attached pilasters, buttresses etc. in super structure.

Columns, Pillars, Piers and likes- rectangular or square in shape

Suspended floors, roofs, access platform, balconies (plain surfaces) and shelves (cast in situ)

Beams, lintels, cantilevers & walls

Folded plates slabs

Stair cases of all types excluding spiral and folded plate type, including risers and landings

Extra for additional height every 1m or part thereof where height of staging for form work exceeds 4.0 metre with adequate bracing, propping etc at all levels, for suspended floor, roof, landing, beam and balcony. (only plan area is to be measured):

Providing and laying integral cement based treatment for water proofing on horizontal surface at all depth below ground level for underground structures using rough Kota stone and consisting of: i) 1st layer of 22mm to 25mm thick approved rough Kota stone slab over a 25mm thick base of cement mortar 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound conforming to IS:2645 over the leveling course (leveling course to be paid separately). Joints sealed and grouted with cement slurry mixed with water proofing compound. ii) 2nd layer of 25mm thick cement mortar 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound. iii) Finishing top with stone aggregate of 10mm to 12mm nominal size spreading @ 8 cudm/sqm thoroughly embedded in the 2nd layer.

Providing and laying integral cement based treatment for water proofing on the vertical surface at all levels by fixing 22 mm to 25mm thick rough Kota stone slab with cement slurry mixed with water proofing compound conforming to IS:2645 with a gap of 20mm (minimum) between stone slabs and the receiving surfaces and filling the gaps with neat cement slurry mixed with water proofing compound and finishing the exterior of stone slab with 20mm thick cement mortar 1:3 (1 cement : 3 coarse sand) with neat cement punning mixed with water proofing compound complete.

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of following applications including surface preparation: i) 1st layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. ii) 2nd layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. iii) 3rdlayer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with coarse sand @ 1.289 kg/sqm and water proofing cement compound @ 0.07 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30cm on parapet wall and tucked into groove in parapet all around. iv) 4th and final layer of brick tiling with cement mortar (which will be paid for separately) For the purpose of measurement the entire treated surface will be measured.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1mx1mx650 micron thick (0.65mm), finished with 12mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement rounding the edge sand making and finishing the outlet complete.

Extra for brick work in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth: Ground Floor

First floor

Second Floor

Extra for providing and placing in position hopping 25x1.60 mm or 2 Nos 6mm dia MS bars reinforcement at every third course of half brick masonry.

Providing and laying AAC Autoclaved aerated concrete block confirming to IS: 2185 (Part-3)-1984) in block masonry with AAC blocks of width 100/ 200mm height 200/250/300mm, length 400/500/600 mm (approved sizes) with cement mortar 1 :6 (1 Cement :6 coarse sand) in superstructure. AAC blocks should have specific gravity 0.6 to 0.65 and crushing strength should not be less than 3 N/ sqmm (testing as per IS: 6441 - 1972).

Providing and laying precast lime fry ash concrete blocks 1 :2:3:6 (1 lime: 2 fly ash : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), including finishing with l0mm thick cement mortar l :3 (1 cement : 3 coarse sand) as required in1 :4 Cement mortar.

15mm thick Granite work (machine cut, table rubbed & mirror polished) for wall lining (veneer work) in cement mortar 1:3 (1 cement : 3 coarse sand) including pointing with cement mortar 1:2 (1 white cement: 2 marble dust) mixed with matching pigment. (Area of slab should be over 0.5 sqm). Granite stone black

Providing and fixing flush door shutters, conforming to IS : 2202 (Part-I), decorative type core of block board construction with frame of first class hard wood and well matched teak ply veneering with vertical grains or cross bands and face veneers on both faces of shutters excluding hinges. 35 mm. thick (single leaf)

Extra for double leaf shutter instead of single leaf. 35 mm. thick (Double leaf)

Providing and fixing factory made UPVC door frame made of UPVC profile section having an overall dimension as below (tolerance ± 1mm) with wall thickness 2.0mm ± 0.2mm, corners of the door frame to be jointed with galvanized brackets and stainless steel screws, joints mitred and plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19mm and 1mm ± 0.1mm wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturers specification and direction of Engineer-in-charge Extruded section Profile size 48x40 mm.

Providing and fixing factory made PVC door shutters of specified thickness made of styles and rails of a UPVC hollow section of specified size 59x24 mm and wall thickness 2 mm ± 0.2 mm with inbuilt edging on both sides. The styles and rails mitred and joined at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. 30 mm thick door shutters with styles and rails of size 60x30mm

Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete : 150x2.5mm (heavy)

100x2.5mm (heavy)

Providing and fixing bright finished brass tower bolts (barrel type) with brass polished MS screws complete: 200x10 mm

Providing and fixing of bright finished brass mortise latch and lock 100x65mm with six levers and a pair of lever handles with brass polished MS screws etc. complete.

Providing and fixing bright finished brass handles with screws etc. complete: 125 mm

Providing and fixing bright finished brass hanging door stopper with necessary brass finished MS steel screws complete.

Providing and fixing IS: 3564 marked aluminium die cast body tubular type universal hydraulic door closer with necessary accessories and screws etc complete.

Extra for providing vision panel not exceeding 0.10 sqm in all type of flush shutters (excluding cost of glass) Rectangular or square

Extra for providing louvers in flush doors upto 0.20 sqm Decorative type doors (50 x 5 mm)

Extra for cutting rebate in flush door shutter (total area of door shutter to be measured).

Providing and fixing expandable fasteners of specified size with necessary plastic sleeves and galvanized M.S screws including drilling holes in masonry work /CC/ R.C.C by drilling machine and making good etc complete. 25 mm long

Providing 40x5mm iron hold fast 40cm long including fixing to frame with 10mm bolts nuts and wooden plug and embedding in Cement Concrete 1:2:4 in blocks of size 30x10x15cm.

Providing and fixing clear float toughened glass door or partation in required thickness frameless in appropriated sizes inclusive of edge molding polish and making required size slot or hole for patch fitting/hardware etc. The glass to be assembled together with patch fitting and hardware in proper alignment with all labour tools and tackles etc complete. (Patch fittings and hardware to be paid for separately). 12 mm thick for door/partation

Providing and fixing double glazed hermetically sealed glazing in aluminium windows, ventilators and partition etc. with 6 mm thick clear float glass both side having 12 mm air gap including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both primary and secondary sealant) etc. complete.

Providing and fixing aluminium work for doors, windows, ventilators and partitions made out of extruded aluminium standard sections (main section with minimum 1.5mm thickness) conforming to IS: 733, IS: 1285 mitred and jointed mechanically including aluminium cleats, neoprene weather stripping gasket beveled edge beading, screws duly fixed in wall/ floor with fixing clips or hold fasteners or bolts and nuts as required aluminium sections shall be anodized transparent or dyed to approved shade according to IS: 1868, minimum anodic coating shall be of grade AC-15. (Glazing to be paid for separately): For fixed portion

For shutter of doors, windows & ventilators including providing and making provision for fixing of fitting wherever required including the cost of PVC/ neoprene gasket required (Fittings shall be paid for separately).

Extra for powder coated (minimum 50 micron) aluminium sections instead of anodized.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC/ neoprene gasket etc. complete. (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness

Providing and fixing steel door made of angle iron of suitable sizes with M.S. grill of approved pattern made of M.S. flats or square or round bars coat of red oxide zinc chromate primer.

Providing and fixing of floor spring IS: marked (Everite, Door link or any equivalent make) with stainless steel cover plate

Providing stainless steel railing/ grill made of S.S. flats, hollow S.S. pipe or square/ rectangular sections of approved design fixing in stair case, balcony or other places with metal fasteners and stainless steel bolts etc complete. SS Grade 304

Steel work in tubular (round, square or rectangular hollow tubes etc.) structure in built-up sections, trusses and frame work including cutting, hoisting, fixing in position upto a height of 5m above plinth level, consisting of columns trusses, roof and bottom purlins, base plate, holding down bolts, wind ties bracing (if required), bolts, nuts and washers for fastening etc. complete with applying a priming coat of red oxide zinc chromate primer. Electric resistance or induction butt welded tubes Grade-300

Extra for curvature in making steel work in tubular structure in built-up sections, trusses and frame work

Extra for hoisting trusses and placing in position over height above 5m for every 2.5 m height or part thereof.

Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of red oxide zinc chromate primer. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing M.S. fan clamp/hook for ceiling fan made out of 16 mm dia M.S. bar bent to shape with hooked ends in R.C.C. slabs, beams during laying including painting the exposed portion of loop.

Providing and fixing false ceiling at all heights with 15 mm thick integral densified Microlook tegular edged lightweight calcium silicate false ceiling tile reinforced with fibre and natural filler false ceiling tiles of Size 595x595 MM of approved texture, design and patterns (such as cosmos, spinnton, quatra, gold) having NRC (Noise Reduction Coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum), Non-combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 & 7), humidity resistance of 100%, thermal conductivity 0.048 to 0.050 W/m0 KC as per ASTM 518:1991, Weight 1.900 Kg to 2.100 Kg per tile, 15 MM Edge Density having 450 Kg/cum & 10 MM Central portion of tile having 350 Kg/cum, in true horizontal level suspended on interlocking metal powder coated T-Grid of hot dipped galvanised iron section of 0.40 mm thick on Silhouette grid, rotary stitched double webbed white with 6 mm reveal profile (white/black), comprising of main-T runners of size 15x44 mm of length 3000 mm, cross-T of size 15x42 mm of length 1200 mm and secondary intermediate cross-T of size 15x42 mm of length 600 mm to form grid module of size 600x600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 40 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape wall adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 22x19x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall S.S screws.

Providing and fixing at all height false ceiling consisting of frame work "W" / "U" / "L" sections made of G.I. sheet with zinc coating of grade 120 consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 22mm and 37mm at 1200mm centre to centre one flange fixed to the ceiling with dash fastener 12.5mm diax40mm long with 6mm dia bolts to the angle hangers of 25x25x0.55mm of required length, and other end of angle hanger being fixed with nut and bolts to G.I. channels 45x15x0.9mm running at the rate of 1200mm centre to centre to which the ceiling section 0.5mm thick button wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to centre shall be fixed in a direction perpendicular to G.I. channel with connecting clips made out of 2.64mm diax230mm long G.I. wire at every junction including fixing the gypsum board with ceiling section and perimeter channels 0.55mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450mm centre to centre with 25mm long drive-all screws @ 230mm interval including jointing and fixing to a flush finish of tapered and square edges of the board with recommended filler, jointing tapes, finisher and two coats of primer suitable for board as per manufactures specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed including providing and fixing 12.5 mm thick tapered edge gypsum board conforming to IS: 2095- Part-I all complete as per drawing and specification and direction of the Engineer in Charge but excluding the cost of painting.

Extra for additional height every 1 m or part thereof where height of false ceiling work exceeds 3.5 meters from the floor under consideration for necessary scaffolding with adequate bracing, propping etc at all level of floor for all type of ceiling .Extra height shall be considered from adjacent floor to finished bottom level of false ceiling. (only plan area is to be measured):

Providing and making 6mm thick cement plaster of mix: In Cement mortar1:3 (1 cement : 3 fine sand).

Providing and making 12mm thick cement plaster of mix: In Cement mortar1:4 (1 cement: 4 fine sand)

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) and a top layer 6 mm thick cement plaster 1:3 (1 cement : 3 coarse sand) finished rough with sponge.

Extra for providing and mixing water proofing materials in cement plaster work in proportion as recommended by manufacturer.

Providing and fixing chicken mesh weighting not less than 250 gms/ sqm as per IS : specification in the required width with 40mm long steel nails on vertical and horizontal surface near R.C.C. and brick walls junctions including scaffolding and all lead and lifts etc. complete before plastering upto 10mts in height.

Making grove in cement plaster while plastering upto10 mm deep and 10 mm wide

Providing and applying 2mm thick white cement based Acrylic grade putty with minimum 3 coats applied (a). 4.0 kg/ lOSqm as per relevant IS code 17545:2021 (Product such as Asian trucare, Berger Happy walls Putty , Birla Opus One pro smooth) to make the surface smooth and even with all tools tackles and labour etc. complete for the work .

Providing and applying of Acrylic primer on all surface applied @ 0.80 liters/10 sqm as per relevant I.S. code 15489:1974 (Product such as Asian Spark/suprimo, J.K. Primer, Dulux Acrylic Primer) with all tools tackles and labour etc. complete for the work.

Providing and applying on exterior surface with PREMIUM Exterior Emulsion paint of required shade to give protective and waterproof finish, minimum 3 coats applied @ 1.40 lit / 10 Sqm up to final finish as per relevant I.S. Code 15489:2013 Type-2 Class D, C (Glossy / Semi Glossy finish) (Product such as Asian Apex, Dulux Weather Shield Prima E900, Berger Weathercoat Antidust, Nerolac Everlas Excel, Nippon Sumo Etra, Opus True Flex) inclusive of providing abro tape on edges and article and cleaning of door, windows, floor, and surface as required with all tools, tackles, and labour etc. complete for the work. (With 3 Year Warranty)

Providing and applying 2mm thick white cement based polymeric Exterior grade Putty with minimum 3 coats applied @ 5.4 kg/10Sqm as per relevant IS code 17545:2021 (Product such as Birla wall care, Asian trucare, JK wall putty, Berger Bison wall putty) to make the surface smooth and even with all tools tackles and labour etc. complete for the work.

Providing and applying Premium Plastic Emulsion Paint with roller application. Minimum three coats applied @ 0.75 lit / 10 Sqm up to final finish as per relevant I.S. Code 15489:2013 Type -1 Class D & C (Glossy and Semi Glossy Finish) (Product such as Asian Apcolite Premium, Dulux Super Cover, Berger Easy Clean, Nippon Breezee Metex Gold, Opus I-50 / Calista) Inclusive of providing abro tape on edges and article and cleaning of door, windows, floor, and surface as required with all tools, tackles and labour etc. complete for the work. (With 3 Year Warranty)

paint of required shade to give protective and water proof finish minimum three coats applied @ 1.43 lit / lOSqm up to final finish as per relevant I.S. Code 15489:2013 Tvpe -2 Class D , C , B & A ( Glossy / matt / Egg Shell finish )having high DFT and silicon aditive for elastomaric property (Product such as Asian Ultima ,Dulux Weathershield Maxx , Berger Weathercoat All Guard , Nerolac Excel Total , Nippon Durafresh Expert , Opus Tru Look) inclusive of providing abro tape on edges and article and cleaning of door, windows, floor and surface as required with all tools tackles and labour etc. complete for the work. (With 4 Year Warranty) ^ ^

Providing and applying Aluminium paint mimimum 2 coats in all metal surface applying @ 0.75 lit/ 10 Sqm up to required finish as per relevent I.S. code 2932: 2013 of (Product such as Asian Apcolite aluminium paint, Dulux Aliminium paint, Burger Superior Aluminium Paint) with all tools tackle and labour etc. complete for the work.

Providing and applying acrylic modified resin EXTERIOR TEXTURED with special quality silica quartz plaster as an intermediate coating on external surface giving protective layer and decorative finish on plastered surface in approved design and shade (product such as Asian Apex Scries Duracast Dulux weathersheald sandtax creation) as per manufacturer's specifications inclusive of providing abro tape on edges and article and cleaning of door, windows, floor and surface as required with all tools tackles and labour etc.complete for the work. 2.0mm thickness (average) having design scratched with leveled & smooth surface.

Providing and laying Matt/Glazed finish HOMOGENEOUS ACROSS FULL BODY VITRIFIED floor tiles (heavy duty) with water absorption less than 0.05% and conforming to IS: 15622-2017 of 1st quality of approved make in all colours and shades and size mentioned below (+/- 10mm), laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete. Size 600x600mm thickness 9 to 10mm

15 mm thick Table rubbed polished Granite stone slab flooring laid over 20mm (Average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry including rubbing and polishing etc. complete. (Area of slab should be 0.50 sqm and above) Granite stone black

25 mm thick KOTA stone slab flooring over 20mm (Average) thick base of cement mortar 1:4 laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding rubbing and polishing etc. complete (Area of slab to be over 0.20 sqm and upto 0.50 sqm)

Cement concrete flooring with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm) finished with a floating coat of neat cement. 50 mm thick

Providing and laying non-modular brick tiles of class designation 3.5 over mumty roofs grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement, over a 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat .

Extra for providing and laying vitrified floor tiles with 2-5mm grove in between the tiles including grouting the grove with water resistant epoxy compound or with white cement and approved pigments etc. complete. Size 1000x1000mm

Extra for fixing glazed/ Ceramic/ Vitrified floor tiles with cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS: 15477 (Type 1) for interior applications, using 5kg. adhesive per sqm of tile area, in 3mm-6mm thickness in place of cement mortar.

Extra for fixing glazed/ Ceramic/ Vitrified floor tiles with cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS: 15477 (Type 2) for interior/exterior applications, using 5kg. adhesive per sqm of tile area, in 3mm-6mm thickness in place of cement mortar.

Providing & laying 60mm thick precast interlocking concrete blocks of approved size (approx 305 sqcm) and shape/ pattern, over 40 mm thick average complete coarse sand bed with joints of 3mm thick filled by fine sand including leveling with surface vibrator, temping and sweeping etc. complete of minimum compressive strength of 250 kg/sq.cm Pigment Coloured (rubber mould) precast interlock concrete blocks

Providing and laying Glazed Vitrified wall/dado tiles (GVT/PGVT) with digital print of random design with water absorption less than 0.08% and conforming to IS: 15622-2017 of 1st quality of approved make in all colours and shades and size mentioned below (+/- 10mm) for wall/dado laid on 12mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete. Size 600x600mm thickness 9 to 10mm

15 mm thick Table rubbed polished Granite stone slab flooring laid over 20mm (Average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry including rubbing and polishing etc. complete. (Area of slab should be 0.50 sqm and above) Granite stone lakha red/ shahi red

15 mm thick Table rubbed polished Granite stone slab in risers and treads of steps ,skirting, dado and pillars laid on 12mm (Average) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry including rubbing and polishing etc. complete (single stone is to be used for risers and treads of steps and width of stone for skirting and dado shall be equal to the height of skirting & dado and length of 1.0 m). Granite stone black

15 mm thick Table rubbed polished Granite stone slab in risers and treads of steps ,skirting, dado and pillars laid on 12mm (Average) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry including rubbing and polishing etc. complete (single stone is to be used for risers and treads of steps and width of stone for skirting and dado shall be equal to the height of skirting & dado and length of 1.0 m). Granite stone lakha red/ shahi red

15mm thick Granite work (machine cut, table rubbed & mirror polished) for kitchen platform, vanity counters, window sills and similar locations of required size laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) including joints treated with white cement mixed with matching pigment including rubbing and polishing to edge moulding to give high gloss finish Granite stone black

Extra for providing edge moulding to 15mm thick stone counters, vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work

Extra for making opening of required size & shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble/Granite/stone work including making necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete.

Providing and fixing 15mm thick Granite (machine cut, table rubbed & mirror polished on both sides) for partition curtain in toilets or similar locations of required size in wall with cement mortar 1:4 (1 cement : 4 coarse sand) including cutting chase in wall and joint with wall treated with white cement mixed with matching pigment including rubbing and polishing to edge moulding to give high gloss finish. Granite stone black

DOOR WORKS Providing and fixing of Metal Fire door from ISO 9001:2015 certified Manufacturer. The door must have been manufactured with galvanised GI sheet of GPSP Grade as per IS 277. All Fire doors must satisfy the requirement of latest NBC 2016 Part 4 for Fire & Life Safety guidelines for 120 minutes Fire Rating with minimum 20 minutes Insulation properties along with its Stability & Integrity for 120 minutes. The Prototype sample of the door must carry a prior test evidence as per IS 3614 part-2/ BS 476 Part 20 & 22. The manufacturer must submit the copy of test evidence prior to start of production .The offered test certificate should either carries it's Validity or certificate must not be older than 5 years from CBRI / NABL Accreditated Lab i.e Spectro / International Lab i.e Exova / TBW etc. Recommended fire door must also be certified by a third party evaluation program from approved International agency like IFC/ Intertek/ Certifire and must carry a lable on all doors. All doors should be finished with Powder coating in desired regular RAL Shades. Door frame shall be Single rebate profile of section 100 x 57 mm made out of 1.20mm thick galvanised steel sheet with a factory pre-punched groove so as to accomodate Fire & smoke seal size 10x4mm. Frames should be butt jointed and field assembled with bolting system for proper strength .Frames should be provided with back plate for anchor fasteners (payable extra) for installation on a finished plastered wall opening. The Air gap between Wall and frame can be filled with fire retardant sealant. Door leaf should be minimum 46mm thick fully flush double skin door. Door leaf must be manufactured from 0.8mm (22 guage) thick galvanised steel sheet. The door should be provided with reinforcement pads to receiving appropriate Hardwares of Becker Fire Solutions or Equivalent make. The Shutter shall be filled with proprietary infill material. For Double leaf doors; astragal has to be provided on meeting stile for both active and inactive leaf. Vision panels wherever required should be of 120 minutes fire rating and should be of nonwired type. fixing of Interlayered FR Glass of Saint-gobain, Pyrobeck Glaverbel or equivqlent make minimum 11 mm thick interlayred, 120 minutes fire Rated (EW120, El 20 minutes) Non Wired, Toughened Interlayered Glass of approved make and is to be fixed in between the glass beading by using ceramic fiber of size 300 mm x 600mm (Clear vision) and the manufacturer should have tested the similar glass of similar size or bigger size. The Location of the Fr Glass will be as per the directions of Engineer-in-charge (Actual supplied Glass size will be meaured for payment). FIXTURES FOR DOORS a)Supply & fixing of SS Ball Bearing Hinges of size 100 x 75 x 3mm complet with SS Screws of BB1953 Becker F.S Make (4 Nos per panel) (Required For All Doors) (b) Supply & fixing of anchor fastners of HILTI/ FISHER/ Equvalent of maximum 80mm length. (c) Supply & fixing of door closers of BLC-0408 Becker F.S Make. d)Supply & fixing of PEL 246/346 Becker F.S. double leaf panic exit devices. e) Single Leaf Panic Bar Set Double Leaf Panic Bar Set f) Supply & fixing of PEL905 Becker F.S. Make Panic Trim For Operation From The Other Side Of The Panic Bar. g) Supply & fixing of Mortise Dead Lock Becker F.S. Make. (Required for Corridor, services area etc) Supply & fixing of SS D Type Offset Pull Handle of size 300mm mm Long of PHD2230 Becker F.SMake. h)Supply & fixing of Mortise Shash Lock With SS Lever Handle Of SL7260 Make i) Supply & fixing of Stainless Steel 304 grade 300mm Long Concealed Flush Bolt of BFBS1930 Becker FS Make with necessary screws as required. (Required with all varieties of Double Leaf door except having 3 Point Panic Bar) j) Supply & fixing of shaft lock with allen key of Becker FS Make. k) Supply & fixing of SS flush pull handle of BFPR1250 Becker FS Make.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat Frame size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed in position with M.S hold fast/ lugs/ SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge.

Providing and fixing factory made 35 mm thick single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-in- Charge.

Providing and fixing factory made 35 mm thick single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. complete as per direction of Engineer-in-Charge.

ROOFING WORKS Providing and fixing of vendor- 65/400 OR 50/429Self Supported Secret Fix Aluminum STANDING SEAM ROOFING SYSTEM in 0.9 mm thick in AA-5052 Aluminium Alloy comprising of the following layers : 1.Top Layer - The topmost profiled sheeting of Aluminium Kingspan 65/400 self supported standing seam roof system manufactured from aluminium alloy AlMnlMg1 Quality AA 5052, in accordance with B209M/ BS-EN-485-2:1995 minimum material thickness of 0.90 mm and 60 Micron Durabond finish /60 Micron PVDF finish in accordance with BS-EN-1396: 2007 finish including Accessories. Original make of aluminum coil to be Gramco,Bahraun/Euramax,E.U/Hulemin,South Africa, and material test certificate (MTC) to be submited. The support halters shall be manufactured from extruded aluminium alloy 6082 T6 in accordance with BSEN 755 part2. Each aluminium halter shall be coupled with a 6mm thick black polyamide thermal barrier base pad. The material properties shall be as follows: Ultimate tensile strength: minimum 200 N/mm2, 0.2% Proof Stress: min 185 N/mm2, Modulus of elasticity: 70,000 N/mm2. Sheets are to be laid in Single Length to meet the requirements of the building geometry and fixed on Aluminum Clip/ Halter and which is fixed to purlin through Bottom sheet with screws. (Color as per architect choice) Aproved Make: KINGSPAN / BEMO / SANKYO / VIJAYNATH Please note: Detail structural load calclation report to be submitted by the manufacturer based on wind load as per IS 875 and screw pull out force.2. Insulation Layer - Rockwool Insulation of 150 mm thickness x minimum 60kg/m3 density. K-value 0.037 W/mK as per standard ASTM C-518. Fire classification as per BS 476: Part 6&7 / EN-1350-1 / UL-273.1) Thermal Transimttance (U-value) to be 0.35 W/m2.K including all losses and calculation to be submitted in accordance with BS EN ISO 6946 and shall take account 2)SoundTransmissionClass(STC) tobe38±3.CalculationofSTC to be submitted by the manufacturer when tested to ASTM E 90 -97. 3.VapourControlLayer–Doublesidedaluminiumfoilofminimum thickness 0.15mm. 4. BottomSheet–Supply&Fixing of Colour coatedGalvalume profilesheetof1000-1050mmeffectivecoverwidthand28-35mm height ribs withsubtlesquareflutinginthefivepanat200-250mm centre-to-centre. The feedmaterial ismanufacturedout of nominal 0.50mmTotalCoatedThickness(TMT),Hi-strengthsteelwithmin. 550MPayieldstrength,metallichotdipcoatedwithAluminium-Zinc alloy (55%Aluminium, 45%Zinc) as per AS 1397- Zincalume AZ150(Min.150gms/sq.mt totalonbothsides)Fixedtothepurlins with self drilling screws at 500mm spacing. Note:1.PurlinspacingshouldbeMaximum1.4mC/C&Purlintobe provided by the client. 2. MS structure/Frame work separate of the thermal bridging effects of any fixing elements.

Supply and Fixing of 0.90 mm thick Aluminium Flashing (Specification same as above) maximum girth of 578 mm.

SPECIALIZED ITEM - SPORTS DEPARTMENT Supplying laying and commissioning 7 mm thick Seamless point elastic indoor sports floor. The system consists of a high resilient granular base mat with polyurethane self-leveling elastic wear layer covered by a wear resistant mat top coat finish. The PU Sport© system (i) Elastic Layer 5 mm thick rubber MAt with the following specifications of volumetric weight 750 - 775 gm/m², tensile strength 0.60N/mm² 2 mm thick PU includes (ii) 1 Layer two component polyurethane pore sealer (iii) 2nd Layer of two component polyurethane self-leveling wear coat that ensures exceptional durability. (iv) 3rd Layer two component aliphatic polyurethane topcoat with very high abrasion resistance, as well as stain resistant. (v) Line Marking as per requirement of the games. complete as per direction of Engineer-in-Charge.

Supply & laying of (9+2) mm synthetic PU flooring approved by FIVB/FIBA/IHF/BWF for Multipurpose courts. The Synthetic Flooring should conform to the following specifications: Shock absorption 27%: Standard deformation 1.1mm: Rolling Load 1500: Impact resistance at 10 c >8 Nm: Residual impression 0.20mm: Ball rebound 96-99%: Sliding properties 88-102 as per EN 14904 Standard. Product to be only of European, American, Australian or Indian Origin. The Product must be approved by FIVB, FIBA, IHF and BWF. (INDOOR HALL SPORTS FLOORING) complete as per the instructions of the engineer-in charge.

Providing & installation of Safelock 25 mm thick interlocking rubber tiles of sizes 50*50 cm with 4.6 kgs weight for gymnasium floor. Safelock is a mix of natural rubber & recycled rubber with Elephant skin pattern. It will be UV resistant & the thicker layer of rubber matting protects the floor as well as the user. It also dampens sound & absorbs shocks.including cost of all materials, labour, conveyance, sundries, T&P, complete as per direction of Engineer-in-Charge.

SPECIALIZED ITEM - SPORTS DEPARTMENT Providing & Fixing of the cubical unit and it shall be installed in approved finish, shades and colors as per specifications and direction of Engineer in charge. The cubical unit shall be minimum 5 years guarantee for the board against any moisture and 5 years guarantee for the hardware’s. The section covers fixing of toilet cubicles of 1000mm x1500mm as per specifications/ site drawings. Cubicle height to be 1980 mm., Partition Board = Made from solid grade compact high-pressure laminate as per IS:2046 manufactured under high specific pressure > 5 MPa and temperature >120oC with bunch of Kraft papers impregnated with thermosetting phenolic resin and decorative papers made of Alpha cellulose fiber impregnated with thermosetting melamine resin which provide superior scratch, abrasion, heat, chemical, impact, graffiti & moisture resistance along with anti-bacterial properties. Panels have a black core that when machined, presents a distinctive black edge. Panel thickness 12 mm. Design no. as specified by Arch. / Engr. in suede finish. Size of panels to be as per drawing. .(min. 1.2 Sqm area) Accessories: Rectangular head frame structure made from Stainless steel grade 304. Surface finish to be brush type. A thin plastic film pasted for surface protection. Corner joinery section made from Stainless steel grade 304. Surface finish to be brush type. A thin plastic film pasted for surface protection. Wall joinery section with hamming profile made from Stainless steel grade 304. Surface finish to be brush type. A thin plastic film pasted for surface protection. Adjustable Palm Design Pedestal Footing of base diameter 64 mm made from Stainless steel grade 316 giving a clearance height of 150 mm. Surface finish to be matt type. Spring loaded Butt Hinges made from Stainless steel grade 304. Surface finish to be mat type. Covers to be lacer coated. Conical shape Coat hook with rubber stopper made from Stainless steel grade 304. Surface finish to be matt type. Round Doorknob diameter 30 mm with grooves for better hand grip made from Stainless steel grade 304. Surface finish to be matt type. Rotating Thumb-turn locking system with privacy indicator made from Stainless steel grade 304. Surface finish to be matt type. Anti-noise rubber padding of thickness 2 mm and width 10 mm Stainless steel grade 304 screws. Anti-rotation Nylon polyamide grade-6 expandable wall plugs. complete as per direction of Engineer-in-Charge.

Providing and installation of Acoustical Wall panelling wood finish slats Upto 2400 mm height made out of HDF board, Malamine/ Veneer laminate finish, perforated wooden graaved slats (2mm groves @ 8mm centers) / (2mm grooves @32 mm centers)/ (2mm grooves @ 64 mm centers), backlined with black acoustical fleece, tounge grooved edge for a seemless look, FR grade of lineal dimension size 128mmx 2440 mm x 16mm thick having density 1000kg/ Cum, weight 12.8 kg/Sqm installed by using GI strut system. The GI strut system includes GI cross channel having thickness of 0.45mm, length 3600 mm, knurlled web 40mm, depth 10mm and equal flanges 15mm is fastened vertically/ Horizontally at every 600 mm centers. Aluminium core cross channel having thickness 0.5mm, Length 2400 mm, web 15mm and 27mm, Depth 18mm and flanges of 7mm with suitable edge and center brackets is then fixed perpendicular to cross channel with the help of fasterners at every 400mm centers. Contractor to provide expansion joints of 3mm at every 5mts bothways.

Providing and fixing acoustical wall paneling using Knauf Danoline make Design panel of size 2400mmx900mmx12.5mm thick as per the specification - High grade, glass fibre reinforced acoustic gypsum boards with CLENEO technology & acoustic perforation Tangent T3L1- 4mmx14mm oval perforation, 20mm/10mm c/c with 15.8% open area. The Acoustic Designpanel will be furnished with a grey (white) absorbent felt backing with an airflow resistance of 330-460 Ns/m³ (DIN 53887) Full perforated – A2-s1,d0 (C1) Fixing :- DesignPanel acoustic gypsum boards shall be installed by screw fixing integrated in gypsum ceiling systems and drywall structures on standard 25 mm furring channels fixed on main profiles. It should also have 50mm thick glasswool backing with 48kg/m3 density.The acoustic Designpanels are with four sides tapered edges for easy joint filling, and shall be painted on site with standard emulsion paint using short piled paint rollers.As approved by Architect and as specified by manufacturer. Core :- High grade, Glass Fibre Reinforced Gypsum , Size :- 2400 X 900mm, Thickness :- 12.5mm, Fire rating :- Class 1 ; K1 10, B-s, d0 can be used in a BD 30 construction, Fire Class :- B-s 1, d0, Realtive Humidity :- The product is designed to perform under normal conditions of use. Tested at 90% RH and 30 DegC. The product can withstand ambientp temperatures of up to 50DegC., NRC : - Tangent- 0.65. (Basic Rate :- 1776/SMT.) (LOCATION: CRY ROOM/SOUND ROOM/STAGE/MULTI PURPOSE HALL)

Providing of Safety polyethylene outer swim Lifebuoys ring dia 600 mm

SPECIALIZED ITEM - FLOORING Providing and laying Porcelain pool tile of size 245 mm x 120 mm and thickness 7 mm conforming to FINA (Federation International De Nation) Standard on horizontal and Vertical surface (Floor and Side Walls) in swimming pool of approved manufacturer and of shade approved by architect or engineer in charge like Light Blue / Aqua Blue etc. laid in approved pattern on 3- 6 mm ( 5mm average) thick bed of adhesive mortar of Polymer modified cementitious adhesive ( Bal Endura gold star / latecrete / Rock force ) in conjuction with polymer modified liquid Bal Endura admix Adlor equivalent product of latercrete / Rock force mixed in required porportion as specified by manufacturer including filling / scaling of joints 2-3 mm thick between the tiles with epoxy grout of Bal Endura Epoxy grout / Latecrete / Rock force with matchingcolour pigment to make it water tight and finished neat complete as per direction of Engineer-in-Charge

Providing and laying Porcelain pool tile of size 245 mm x 120 mm and thickness 8 mm conforming to FINA (Federation International De Nation) Standard on Horizontal and Vertical surface (Side Wall) for Lane Marking in swimming pool of approved manufacturer and of shade approved by architect or engineer in charge like Cobalt etc. laid in approved pattern on 3- 6 mm ( 5 mm average) thick bed of adhesive mortar of Polymer modified cementitious adhesive ( Bal Endura gold star / latecrete / Rock force ) in conjuction with polymer modified liquid Bal Endura admix Adlor equivalent product of latercrete / Rock force mixed in required porportion as specified by manufacturer including filling / scaling of joints 2-3 mm thick between the tiles with epoxy grout of Bal Endura Epoxy grout / Latecrete / Rock force with matchingcolour pigment to make it water tight and finished neat complete as per direction of Engineer-in-Charge.

Providing and fixing Jaquar make vitreous china pedestal type Antigerm Fluoro Polymer coated wall mounted European type W.C. pan size 760x365x620mm system cde CNS WH 16 with soft closing seat cover CODE WCS-7 and 7.2 litre low level slim dual flush of code CNS-02 & dual flush fitting code CNS WCF 01 PP (poly Propeline) made 80mm thick concealled flushing cistren, flushing capacity CODE WHC-WCF 1 and making good the wall and floors wherever required.

Providing and fixing Jaquar make white vitreous china Anti germ Fluoro Polymer Coated Under counter Wash Basin Size 190x550x435mm with C.I. Brakets, 15mm C.P. 32mm C.P. brass made waste Trap size 200x300mm fitting and wast coupling and bottle trap code ALD 769 L 250x190 fixures complete including Painting of fittings and cutting and making good the wall and floors wherever required.

Providing and fixing Jaquar make 8mm thick froasted urinal glass partition size hght 900x450mm brass made bracket with chrome plating

Providing and fixing 15 mm nominal bore C.P copper connection pipe with C.P brass nuts collar and PVC bush of approved quality: 45 CM length

Providing and Fixing Vitreous China Urinal Basin of Jaquar urinal of size (mm) 530 x 340 x 360 (Item Code No. URS-WHT-0707) and coupling in C.P. Barass of Jaquar make 32mm size full thread with 80mm height (Item Code ALD-705) including fixing to wall with Rack bolt (Mild steel) (Item Code-2PS-MST-RB03) all complete

Providing and Fixing Jaquar make 2 Way Bib Cock with Wall flange. (Item Code No. FLR-5041 N) 2 Way Bib Cock (Item Code No. FLR - 5041 N)

Providing and fixing PVC waste coupling in wash basin/ sink. 40 mm

Providing and fixing cast iron grating for gully trap 100x100mm square or round

Tee/ Tee with door/ Bend 45°/ Bend 90° 110 mm

Double "Y" with or without door 110 mm

P" trap 110mmx110mm long

Nahani trap 110x75mm

Supplying of Jaquar make 2-Way Bib Cock with wall Flange Model Name QQT-7041

Providing and fixing Jaquar make in position best indian bonut size 24mm ceramic disc size 19mm and minimum body thick ness 2mm nickle plating. 1 micron and crome plating 0.3 micron BIB cock two way with health faucet.

Providing and Fixing Jaquar make Soap Dish Holder (Item Code No. ACN-1131N)

Supplying of Jaquar make Toilet Roll Holder Model Name AQN 7751

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: Hand shower set with flexible extension pipe

Shower rose (revolving type) (150mm)

Wall mixer (telephonic type) with crutch arrangement for hand shower (1400gms)

Supplying of Jaquar make Soap Dish Holder Model Name CAN 1131N

Providing and fixing stainless steel drain jali of approved make/quality.

Providing and Fixing Jaquar make Hand Shower (health Faucet) with 8mm dia, One meter long flexible Tube & wall Hook (Item code No. ALD - 573)

Providing and Fixing Jaquar make Toilet Roll Holder (Item Code No. CAN-1151N)

Providing and laying in trenches 3 layer PP-R (Poly propylene Random copolymer) pipes SDR 7.4 U V stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply including all PP - R plain & brass threaded polypropylene random fittings including excavation of trenches, refilling the same and testing of joints complete PN - 10 Pipe, 160 mm OD (SDR - 11)

Providing and fixing on wall face or under floor UV stabilized Unplasticised Rigid PVC pipes (single socketed) having 3.2mm wall thickness conforming to IS : 13592 (4kg/sqcm) including required couplers, jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion etc complete. 75 MM DIA PIPE

110 MM DIA PIPE

150 MM DIA PIPE

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. INTERNAL WORK - EXPOSED ON WALL 32 mm nominal outer dia .Pipes.

40 mm nominal outer dia .Pipes.

50 mm nominal outer dia .Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. CONCEALED WORK including cutting chases and making good the walls etc., 15 mm nominal outer dia .Pipes.

20 mm nominal outer dia .Pipes.

25 mm nominal outer dia .Pipes.

32 mm nominal outer dia .Pipes.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 15 mm nominal bore

20 mm nominal bore

25 mm nominal bore

Providing and fixing gunmetal single acting air release valve with screwed inlet 25 mm dia and with necessary G.I. coupling, valve to be fitted on top of Air vessel or on wet riser as per specification.

Supplying, fixing, testing and commissioning of flanged butterfly valve PN 1.6, with Bronze/Gunmetal seat duly ISI marked complete with Nuts, Bolts, washers, gaskets, conforming to IS: 13095 of following sizes as required. 80mm dia

100 mm dia.

Providing and fixing enclosed type water meter (bulk type) conforming to IS : 2373 and tested by Municipal Board complete with bolts, nuts, rubber insertions etc. (The tail pieces if required will be paid separately) : 80 mm dia nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

Supplying and fixing of MS hose cabinet box of made of 2 mm thick MS sheet and 40 x 40 x 5mm angle iron with front openable cover having 6 mm thick glazed glass viewing window i/c necessary locking arrangement, on existing wall/ brick platform etc complete as required. Size 600 mm x 600 mm x 500 mm

Supplying and fixing 63 mm dia, 15 mtr long RRL hose pipe with 63 mm dia Male and Female Stainless Steel-IS: 3444 Grade-1 couplings duly binded with GI wire, rivets etc. conforming to IS: 636 (Type -A) as required.

Painting for M.S. pipe with a coat of red oxide primer and two or more coats of synthetic enamel paint of approved colour and Quality to give an even shade including surface preparation. 150mm dia.

Supplying and installing pressure gauge of 100 mm Ø., 0-300 PSI or 0-21 kg per cm square fitted with 12/15 mm Ø. pad cock valve, and G.I. pipe, elbow etc. as per requirement in approved manner

Providing and fixing standard fireman's axe (tested for 20000 Volts) with heavy insulated rubber handle. (ISI marked)

Supply, erection, jointing, testing & commissioning of "C" Class MS pipes (as per IS: 1239) including necessary specials such as tees, bends, flanges reducers etc., complete on wall/ ceiling. The pipes to be erected on wall or suspended from beams, RCC roof slabs with suitable size MS bars/ angle irons including painting of metal part except pipe line. 150 mm dia

Supplying, fixing, testing and commissioning of flanged butterfly valve PN 1.6, with Bronze/Gunmetal seat duly ISI marked complete with Nuts, Bolts, washers, gaskets, conforming to IS: 13095 of following sizes as required. 150 mm dia

Providing, fixing, testing and commissioning 50mm dia drain system in wet riser line with 50mm dia GM valve, necessary MS "C" class pipe line (upto 1 metre) and accessories complete as required

All types of soil 150 mm dia

200 mm dia

Rocky strata including Boulders. 150 mm dia.

200 mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer –in-charge. 200 mm nominal size dia.

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tube well as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp

Providing ISI Mark 32 mm dia G.I. ( B class) riser pipe and M.S. plunger rod in 3 meter length socketed on one end as per IS: 1239 ( Part I) 1990 with up to date amendments and socket as per IS: 2062/1990 up to date amendments.

Providing and laying in trenches G.I. pipes medium class complete with G.I. fittings including excavation of trenches, refilling the same and testing of joints complete: 40 mm dia. nominal bore

Providing and fixing square-mouth S.W. gully trap grade 'A'’ complete with crushing strength not less than 35kg/cm2, water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design : 180x150 mm size P type

Constructing brick masonry manhole with well burnt modular clay bricks crushing strength not less than 35kg/cm2 in cement mortar 1:4 ( 1 cement : 4 coarse sand), R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation in cement concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg)

Providing and constructing brick masonry circular arch type manhole upto 1.67m depth, 0.91m internal dia at bottom and 0.56m dia at top having brick masonry wall 190mm thick with well burnt modular clay bricks crushing strength not less than 35kg/cm2 in cement mortar 1:4 (1 cement : 4 coarse sand), in side cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement, providing and fixing S.F.R.C. cover and frame (heavy duty, HD 20 grade designation) 560mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182kg, in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) all complete as per standard design (excavation and foot rests shall be paid for separately) : Manhole of depth 0.91m.

Providing, lowering, laying, aligning, fixing in position at and jointing at all level/ depths ISI marked HDPE pipes of PE-100 grade and PN 6 for sewer application as per IS 14333-1996 (amended upto date) in trenches in complete including all material, labour, testing and commissioning as per direction of Engineer. Note : E/w to be measured and paid separately. 100 mm dia

200 mm dia

Supplying, filling, spreading & leveling stone boulders/ Gravels/ Coarse sand, in recharge pit, in the required layers and thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. (excavation of pit will be paid separately). Stone boulders of size range 5 cm to 20 cm, in recharge pit

Gravels of size range 5 mm to 10 mm, over the existing layer of boulders

Coarse sand of size range 1.5 mm to 2 mm over existing layer of gravel

Extra for covering top of membrane with Geotextile, 120gsm non woven, 100% polyester of thickness 1 to 1.25mm bonded to the membrane with intermittent touch by heating the membrane by Butane Torch as per manufactures recommendation.

Providing and constructing brick masonry chamber for underground pipe and and bends with well burnt modular clay bricks crushing strength not less than 35kg/cm2 in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) R.C.C. top slab with 1:2:4 mix (1 cement :2 coarse sand : 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design : Inside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inlets :

Providing and laying nominal mix reinforced cement concrete with crushed stone aggregate using concrete mixer in all works upto plinth level excluding cost of form work. 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20mm nominal size).

Brick work with modular fly-ash lime bricks (FALG Bricks) confirming to IS:12894-2002 of class designation 4.0 in foundation and plinth in:Cement Mortar 1:5 (1 cement : 5 coarse sand)

Extra for precast PCC/ RCC work of any mix including form work, hoisting and fixing in Cement Mortar. 1:2 (1 Cement : 2 coarse sand) and finishing with cement plaster in Cement Mortar 1:3 (1 Cement : 3 coarse sand) but excluding reinforcement.

Providing and placing in position reinforcement for R.C.C. work including straightening, cutting, bending, binding etc. complete as per drawings including cost of binding wire in foundation and plinth all complete: Thermo-Mechanically treated bars FE 500D

Providing and making 12mm thick cement plaster of mix: In cement Mortar 1:3 (1 cement : 3 fine sand)

Neat Cement punning.

Providing, installation, testing and commissioning of dual plate non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc. as required. 150mm dia

Wiring for light/ fan/ exhaust fan / call bell point with 3x1.5 sqmm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) with 5/6 amp modular switch, modular base and cover plate, suitable size G.I. box as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) Short Point

Medium Point

Long Point

Wiring for twin control light point with 3x1.5 sqmm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) with 5/6 amp modular switch, modular base and cover plate, suitable size G.I. box as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5)

Extra for providing and fixing light plug point on board in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) point wiring with modular type 3 pin 5/6 amp socket outlet and 5/6 amp switch including cost of base and cover plate and G. I. box etc. as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5)

Wiring for light plug point with 3x2.5 sq mm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with modular type 6 Amp switch and 3 pin 6 amps socket outlet with modular base and cover plate, suitable size G.I. box, earthing the switch box and socket outlet with same size wire etc. as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) Short Point

Medium Point

Long Point

Extra Long Point I

Extra Long Point II

Extra Long Point III

Wiring for power plug point with 3x4 sq mm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with modular type 16 Amp switch and 6 pin 16 amps socket outlet with modular base and cover plate, suitable size G.I. box, earthing the switch box and socket outlet with same size wire etc. as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) Short Point

Medium Point

Long Point

Extra Long Point I

Extra Long Point II

Extra Long Point III

Wiring for power plug point with 3x6 sq mm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with modular type 32 Amp SPMCB "C" curve and 6 pin 20 amps socket outlet with modular base and cover plate, suitable size G.I. box, earthing the switch box and socket outlet with same size wire etc. as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) Long Point

Extra Long Point I

Extra Long Point II

Extra Long Point III

Wiring for circuit/ sub main wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, wire in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) 3 X 1.5 sq. mm in 20mm conduit

3 X 2.5 sq. mm in 20mm conduit

6 X 2.5 sq. mm in 25mm conduit

9 X 2.5 sq. mm in 32mm conduit

3 X 4 sq. mm in 25mm conduit

6 X 6 sq. mm in 32mm conduit

6 X 10 sq. mm in 40mm conduit

6 X 16 sq. mm in 50mm conduit

Supplying and fixing of following sizes FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with accessories in concealed complete as per specification and IS: 9537 (2000 Part 5) 20 mm dia

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, multi strand wire in the existing surface/ concealed, FRLS PVC conduit / PVC casing caping as per specification and IS: 694 (2010) 1 x 2.5 sq. mm

2 x 2.5 sq. mm

Supplying and drawing UTP 4 pair Cat 6 LAN wire in existing surface/ concealed Steel/FRLS PVC conduit as per specification

Supplying and fixing following modular switch, socket, other accessories on the existing modular plate & switch box including connections but excluding modular plate etc. as per specification. 5/6 amps one way switch

Bell push

15/16 amp switch

3 pin 5/6 amp socket outlet

6 pin 15/16 amp socket outlet

Fan regulator (two module size) electronic stepped type moving all rounds

Plug Top (Deluxe type) 3 pin 16 Amps (For power plug).

T.V. antenna socket outlet

25/32 amp A.C. Starter switch

Batten/ angle holder

Blanking plate

Providing and fixing composite unit for computer points having modular type 1 No 6 pin 16 amp socket outlet, 1 No 16 amp switch, 3 Nos 3 pin 6 amp socket outlets, 3 Nos 6 amp switches, suitable G.I. box, base and cover plates, earthing the sockets and switch box including etc. as per specification.

Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts A.C. supply, complete as per specification. Deluxe

Providing and fixing round/ hexagonal fan box (125mm dia) depth 75mm (max.) with 12mm dia steel bar hook, 1.6mm thick MS sheet cover, in RCC slab etc. as per specification.

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, including connection, earthing etc. complete as per specification.

Supplying and fixing of wall/ cabin fan including connection etc. as per specification. P.F. should be greater than 0.9 400 mm sweep

Supplying, installation, testing and commissioning of following sizes heavy duty (continuous running) 1400 rpm exhaust fan in existing opening in wall including earthing etc. complete as per specification. P.F. should be greater than 0.9 300 mm sweep

Supplying, installation, testing and commissioning of 250/ 300 mm sweep 1400 rpm medium duty (continuous running) exhaust fan in existing opening in wall including earthing etc. complete as per specification. P.F. should be greater than 0.9

Supplying and fixing following sizes of down rod of 15/20mm dia M.S. pipe of thickness 2 mm to ceiling fan including painting with matching colour etc. as per specification. 90 cm long

Supplying, installation, testing and commissioning of following LED fitting (luminaries) Panel Light in round/ square shape complete with electronic driver heat sink capacitor and all other accessories on surface/ in false ceiling etc. as per specification and P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt. 18/20 Watt

Supplying, installation, testing and commissioning of following sleek LED panel down lighters (luminaries) in round/ square shape complete with electronic driver heat sink capacitor and all other accessories on surface/ in false ceiling etc. as per specification and P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt. 36 watt, size 600 x 600mm

Supplying, fixing, testing and commissioning of following LED lamps with inbuilt electronic driver heat sink and all other accessories in existing holder/ luminaries as per specification and P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt. 12 Watt

Supplying, installation, testing and commissioning of following LED tube light fitting including batten with Electronic Driver Heat sink Capacitor complete with all other accessories on surface/ in false ceiling, including connection, earthing etc complete as per specification and IP20, P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt. 5 watt {2 feet}

18/20 watt {4 feet}

Providing and making interconnection in cubical panel between BBC and switchgears with following size aluminium strip of length upto 50cm as per specification (To be measured separately for each phase/ neutral). 20x5mm (100 amps)

30x5mm (200 amps)

50x5mm (300 amps)

Providing and making interconnection in cubical panel between BBC and switchgears with following size FRLS PVC insulated copper conductor wire lead of length upto 50cm including providing copper thimbles on both ends as per specification (To be measured separately for each phase/ neutral). 16 sqmm (63 amp)

35 sqmm (125 amps)

Supply, installation, testing and commissioning of 4 pole (3 phase + neutral) aluminium bus bars in existing cubicle type compartmentalized wall/ floor mounted panel board along with suitable size and shape insulators, necessary bolts and nuts etc complete as per specification. 100 amp (20x5mm)

200 amp (30x5mm)

300 amp (50x5mm)

500 amp (75x6mm)

Providing and fixing following rating and breaking capacity MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as per specification, IS/ IEC: 60947-2 and Ics = 100 % Icu. 3 pole MCCB, 25-100A, Adjustable Thermal Release, 18KA

3 pole MCCB, 250A, Adjustable Thermal - Magnetic Release, 25KA

4 pole MCCB, 250A, Adjustable Thermal - Magnetic Release, 50KA

Supplying and fixing on surface/ recess following way, 240 volts SP&N MCB distribution board of sheet steel phosphatized and powder painted complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, including interconnections, earthing etc. as per specification. (But without MCB/RCCB/Isolator) 8 way, Double door

Supplying and fixing on surface/ recess prewired horizontal type following way, 415 volts TP&N, MCB distribution board of sheet steel phosphatized and powder painted complete complete with loose wire box, terminal blocks, tinned copper busbar, neutral link, earth bar, din bar, detachable gland plate, duly prewired with suitable size FRLS PVC insulated copper conductor up to terminal blocks including interconnections, earthing etc. as per specification. (But without MCB/ RCCB/ Isolator) 4 way (4 + 12), Double door

6 way (4 + 18), Double door

8 way (4 + 24), Double door

Supplying and fixing SP MCB, 240 volts, 'B' curve, suitable for lighting and other loads in the existing MCB DB complete with connections, testing and commissioning etc. as per specification. 6 amps to 32 amps

Supplying and fixing SP MCB, 240 volts, 'C' curve, suitable for inductive load in the existing MCB DB complete with connections, testing and commissioning etc. as per specification. 6 amps to 32 amps

Supplying and fixing DP MCB, 240 volts, 'C' curve, suitable for lighting and other loads in the existing MCB DB complete with connections, testing and commissioning etc. as per specification. 63 amps

Supplying and fixing TP&N MCB, 440 volts, 'C' curve, suitable for lighting and other loads in the existing MCB DB complete with connections, testing and commissioning etc. as per specification. 40 amps

Providing and fixing metal clad, TP&N motorized change over switch unit, 415/500 volts, including drilling holes on the board, connections, earthing the body, testing and commissioning etc. as per specification. 250 amps

Providing and fixing penal mounting 230 volt LED type indicating lamp in existing cubical panel including, connections, testing and commissioning etc. as per specification.

Providing and fixing panel mounting digital type VAF (Volt-amp-frequency combined) Multi Function meter of size 100x100 (NS) in existing cubical panel including connection, testing and commissioning etc. as per specification.

Supplying, installation, testing and commissioning following rating single phase 230 volts sine wave inverter (without battery) including connection as per specification. 1.50 KVA

Supplying, installation, testing and commissioning following rating lead acid battery (Maintenance Type) including connection as per specification. 200 AH

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as per specification.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ concealed conduit/ submain wiring/ cable as per specification.

Providing maintenance free earthing with following size GI pipe including making bore pit of minimum 150mm dia, providing and laying approved make Earthing Electrode of Pipe-in-Pipe technology as per IS 3043(R 2016) -1987 made of corrosion free G.I. Pipes having outer pipe of 80mm dia and inner pipe of 50mm dia and filling with specified qty highly conductive compound around pipe and above that with soft soil in bore pit complete and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. as per specification: With 3 metre long GI Pipes and 50 kg back filling compound.

Supplying and laying ISI marked double wall HDPE pipe (IS 14930 Part II) having corrugation on the outer wall and plan surface on inner wall in ground below road, path etc at a depth not less than 40 cm and upto 90 cm including excavation, dismantling of road if required and refilling the trench with excavated material, ramming and making the surface good etc. as per specification. 120 mm outer dia and 103.5 mm Inner dia

Supplying and laying following sizes one number FRLS PVC insulated/XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade direct in ground at a depth not less than 40 cm and upto 90 cm including excavtion, sand cushioning, protective covering and refilling the trench etc as per specification, IS: 1554 (1988, Part 1) / IS: 7098 (1988, Part 1). 3.5 x 95 sq. mm.

Supplying and laying following sizes additional one number, FRLS PVC insulated /XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade direct in ground as in the same trench in one tier horizontal formation at a depth not less than 40 cm and upto 90 cm including excavtion, sand cushioning, protective covering and refilling the trench etc as per specification, IS: 1554 (1988, Part 1) / IS: 7098 (1988, Part 1). 3.5 x 95 sq. mm.

Supplying and laying following sizes one number FRLS PVC insulated /XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade on surface/ existing cable tray with 1 mm thick GI saddle as per specification, IS: 1554 (1988, Part 1) / IS: 7098 (1988, Part 1). 4 x 10 sq. mm.

4 x 16 sq. mm.

4 x 25 sq. mm.

Supplying and laying following sizes one number FRLS PVC insulated/ XLPE, PVC sheathed, unarmoured, aluminium conductor power cable of 1.1 KV grade on surface/ existing cable tray with 1 mm thick GI saddle as per specification, IS: 1554 (1988, Part 1) / IS: 7098 (1988, Part 1). 3 x 10 sq. mm

Supplying, fixing and cramping suitable size and all type aluminium ferule/ lugs to following size 1.1 KV grade power cable core / lead, pressed with high pressure cramping tool including connection to switch gear/ MCCB etc as per specification. . 10 sq. mm

Supplying, fixing and cramping suitable size and all type Copper ferule/ lugs to following size 1.1 KV grade power cable core / lead, pressed with high pressure cramping tool including connection to switch gear/ MCCB etc as per specification. . 6 sq. mm

Designing & Providing of suitable RCC trench in cement concrete 1:3:6 (1 Cement : 3 coarse sand: 6 graded stone aggregate 40 mm nominal size) for laying of cable inground including execavation, steel reinforcement (minimum 35.75 kg per cum), 4" drain wall, drain cover, frame work, curing & refilling of excavated soil etc as per specification.

Supplying and erection of angle/channel iron cross arms/ bracket/ other fitting of approved size and shape including drilling of holes for insulator pins, bolts and nuts etc as per specification.

Supplying, installation, testing and commissioning of submersible pump set for water supply system with submersible motor directly coupled to multi-stage submersible pump of specified discharge capacity, head, delivery size in existing bore well including 2 sets of suitable size holding clamps made out of 50 mm X 6 mm MS flat, connection with suitable submersible cable of standard length etc. as per specification and IS: 694 (2010). Note: submersible Cable should be rust proof, safe from oil / Grease and under water Chemical / abrasion Resistant. 5.0 HP, three phase

Supplying and fixing of following sizes 'B' class G I pipe with welded steel flange of suitable size at both the end of every pipe length, fixing with submersible pump and lowering with the pump in the bore well including necessary rubber gasket, nuts & bolts etc. as per specification. 50 mm dia.

Supplying and fixing M.S. clamp 50 cm long made of 50mmx5mm thick M.S. Flat for holding the pipes and submerable pump set as per specification.

Supplying and fixing 300 mm dia 2 mm thick M.S. sheet cover with 3 cm edge in two past on tube well bore pipe as per specification

Supplying, laying and fixing following size submersible cable along with GI/PVC/HDFC pipe line or laid in ground etc as per specification and IS: 694 (2010). Note: Cable should be rust proof, safe from oil / Grease and under water Chemical / abrasion Resistant. 3x4.0 sqmm

Supplying and laying of approved make stainless steel wire rope of 6 mm dia for support of submersible pump set complete with tying to pump set and pump holding clamp.

Suppying , installation , testing and commissioning of Fire alarm Control panel (UL Listed) suitable for 50 addressable points (Detector & Devices). Comprising of the following system components: Operating units, Periphery boards, Power supplies,System enclosures, with battery backup 24hours and 30minutes,

Suppying , installation , testing and commissioning of Fire alarm Control panel (UL Listed) suitable for 252 addressable points (Detector & Devices). Comprising of the following system components: Operating units, Periphery boards, Power supplies,System enclosures, with battery backup 24hours and 30minutes,

Suppying , installation , testing and commissioning of Additional Loop Card

Suppying , installation , testing and commissioning of Remote Printer Module - Optional

Suppying , installation , testing and commissioning of Panel to Panel network card

Suppying , installation , testing and commissioning of Intelligent Addressable Type Manual Call Point: Intelligent Manual Fire Alarm Box is constructed of durable, molded and polycarbonate material that is matte finished in red with raised white lettering Single-action,Pull-down lever is down, until manually reset,Polarity insensitive via SureWireTM technology

Suppying , installation , testing and commissioning of Short circuit Isolator Base: Local light-emitting diode (LED) indicator UL 864 9th Edition Listed and ULC Listed; FM Approved

Suppying , installation , testing and commissioning of Intelligent Addressable Relay control module for Hooter Interfacing and supervising normally open (N.O) or normally closed (N.C) contacts,Integral single-pole, double-throw (SPDT) relay (up to 4 amps) ,Multi-color light-emitting diode (LED) indicates system status, UL Listed & ULC Listed; FM Approved

Suppying , installation , testing and commissioning of 2 core x 1.5 sq.mm Armoured FRLS cable

Supplying , installation , Testing and Commissioning of Compact Full Range 4" Ceiling Speaker with 40 W RMS power @ 8 Ohms ,70 V/100V: 30 W / 15 W / 7.5 W with all necessery terminals and Connectors.

Supplying , installation , Testing and Commissioning of 4 Channel Audio Amplifier Professional 300-Watt (Per channel 70 to 80 Watts into 4 Ohms OR Per channel 40 to 60 Watts into 8 Ohms) Light Weight 4-Channel Power with all necessery terminals and Connectors.

Supplying , installation , Testing and Commissioning of 2.5Sq.mm Speaker cable Cross sec Area 1.5 sqmm, No of Strands 75 , Size of Strands 34 , Cond.Type ATC Speaker Cable - Copper 2Core, Twisted, Tin Coated, Shielded 2.5SQMM (70/.2) ATC 2/C SPEAKER CABLE 14AWG with all necessery terminals and Connectors.

Supplying , installation , Testing and Commissioning of 17U Equipment Rack, with Metal Side Panel, Back Door, Front Glass Door, Floor Wheel, 15u PDU Unit, Cooling FAN, Cable Manager, Counter Shelf with all necessery terminals and Connectors.

Supplying , installation , Testing and Commissioning of UHF Wireless Cardioid Condenser handheld microphone system with Frequency Response of 60 Hz to 16 kHz , RF Sensitivity 10dBμV (S/N 60dB @ 20 kHz deviation) or better, Total Harmonic Distortion <1.0% (at 1 kHz, ±20 kHz deviation) or better, Dynamic Range > 108dB or better, on/off switch operating range 60 mtrs or better, RF Power Output: 10 mW or better, maximum Output level XLR / Balanced: +4 dBV & 6.3 mm (¼") / Unbalanced: -2 dBV with all necessery terminals and Connectors.

Supplying , installation , Testing and Commissioning Cardioid Condenser Gooseneck Microphone with goosenck length of 415mm or more. Flexible gooseneck head for accurate positioning. Shock Mount to be inlcuded with Microphone from same OEM with Frequency Response 70 Hz - 16,000 Hz; It shall be capable of handling sound input levels up to 134 dB with a dynamic range of 106 dB. Nominal open-circuit output voltage shall be 12.0 mV at 1 V, 1 Pascal or better, Signal-to-noise ratio of 66dB,1kHz at 1Pa or better. Support 11V to 52V phantom power for operation. Impedance 100 ohms or better complete with Foam Windscreen with all necessery terminals and Connectors.

Supplying , installation , Testing and Commissioning of MXLR (Male External Line Return) Connectors Pin with all necessery terminals and Connectors.

Supplying , installation , Testing and Commissioning of FXLR (Female External Line Return) Connectors Pin with all necessery terminals and Connectors.

Supplying , installation , Testing and Commissioning of 15 Meters Digital Conference System Signal Cable Compatible with respective conference System with all necessery terminals and Connectors.

Supplying , installation , testing and commissioning of 2 MP DOME Camera weather & dust proof IP based Fixed Lens day/night Camera (IP66) 2Megapixel CMOS Image Sensor,H.265 / H.264 triple-stream encoding , WDR(120dB), Day/Night UL, CE, FCC Certified as per the specifications.

Supplying , installation , testing and commissioning of 2 MP Bullet Camera weather & dust proof IP based Fixed Lens day/night Camera (IP67 , IK 10) , 2 MP CMOS Image Sensor ,H.265 and H.264 triple-stream WDR(120dB), Day/Night, UL ,CE FCC Certified as per the specifications.

Supplying , installation , testing and commissioning of 32 Channel NVR 2 Sata port Up to 32 channel IP camera input , Max 320 Mbps incoming bandwidth ,Smart H.265+/H.265/Smart H.264+/H.264 dual codec decoding , Up to 12MP resolution preview and playback , Support 8 SATA HDDs up to 10 TB each, 4 USB(1 USB3.0, 1 USB2.0) , 1 HDMI / 1 VGA simultaneous video output ,ONVIF Version 2.4 conformance , Alarm In / out 16/6 , Two way talk 1 Channel Input, 2 Channel Output RCA , 1 RJ-45 port (10/100/1000Mbps) Support ANPR Cameras as per the specifications.

Supplying , installation , testing and commissioning of 4 Port POE Switch 10/100 4 Port PoE with 2 10/100 Mbps Uplink ,Power Budget 60 Watt , Max 30 watt per port as per the specifications.

Supplying , installation , testing and commissioning of 8 Port Giga PoE Switch 10/100/1000 8 Port with 2 GigaJ 45 uplink, PoE switch ,AI Extend , AI Vlan as per the specifications.

Supplying , installation , testing and commissioning of 8 TB Surveillance Hard disk drive Complete as required

Supplying, installation, testing and commissioing of following size LED Monitor, table/wall mount with inbuild speaker minimum 5Wx2,with minimum 1 No of HDMI and USB port including remote control, connecting cable, batteries, and all accessories, connection etc complete as per specification. 55 inch

Supplying , installation , testing and commissioning of 6U Indoor Rack Wallmount 6U 450D With Front Glass Door Lock & Key 550 6U - loaded with cable manager + PDU + Fan complete as required.

Supplying , installation , testing and commissioning of 9U Indoor Rack Wallmount 9U 630D With Front Glass Door Lock & Key 550 9U - (with 1U cable Manager;Fan;6 socket PDU) complete as required.

Supplying , installation , testing and commissioning of 12U Indoor Rack Wallmount 12U 450D With Front Glass Door Lock & Key 550 12U - (with cable Manager;Fan; socket PDU) complete as required.

Supply, installation and testing for HDMI cable.

Supply installation,testing & commissioning of modular type variable refrigerant flow/variable refrigerant volume air cooled outdoor units suitable for cooling and heating, having all hermetically sealed inverter type scroll compressor(s), minimum two compressors for above 14HP modules, microprocessor based controller, top discharge type condensing unit(s), with R410a refrigerant, vibration isolators, with suitable foundation etc. Complete as per specification. The unit shall deliver the rated capacity at AHRI conditions and work even at 50°C ambient temperature without tripping. The unit shall be suitable to work on 400v +/-10%, 3phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as per specification. The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5

Supply, Installation, Testing and commissioning of factory built floor/ceiling mounted DX type double skin type horizontal/vertical air handling units made of 25mm thick panels consisting of pre plasticized G.I. casing of thickness 0.8 mm outside layer and 0.8 mm inside layer with polyurethane foam (PUF) insulation (having density 48 kg/cu m) factory injected between them by injection moulding machine, complete with blower section with blower suitable for static pressure as per specification, minimum 4 bend GSS/PVC eliminators, DX type cooling coil section with aluminium finned copper tubes (tubes thickness not less than 0.5 mm) cooling coil of 6 row deep, filter section with 50mm thick metal viscous/ washable synthetic type air prefilters, belt drive package with TEFC drive motor of efficiency class IE3 suitable for 415 ± 10% volts, 50Hz, 3 Phase AC supply suitably designed for varialbe frequency drive applications, drain connections, stainless steel (18G) drain pan with PUF insulation, 150 mm dia. dial type pressure gauges (2 nos.)and industrial type thermometers (2 nos.) at the inlet and outlet of coil, auto purge valve wherever required, including starter Pannel of suitable capacity, necessary vibration isolation arrangement, without mixing Box etc. complete as per specification and of following capacities 20000 CFM (50 TR) with 6 Rows Coil Cooling 40 sqft. 60 mm Static pressure.

'Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as per specification : 28.6 mm dia (OD) (Hard drawn)with tube thickness 1.2 mm with 19 mm thick insulation

31.8 mm dia (OD) (Hard drawn)with tube thickness 1.62 mm with 19 mm thick insulation

34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation

38.1 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation

41.3 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation

400 mm Wide G.I. Tray Covered with G.I. Sheet for Copper Tubes.

Supplying and installation of Refnet Joints as per site conditions.

All Control /communication wiring between indoor and Outdoor Units with FRLS PVC conduit and necessary clamps/saddling etc. complate as requird.

Supplying, laying, fixing and installation of rigid PVC drain piping of 6 KG/sqcm, duly insulated with 6/9 mm thick nitrile rubber pipe section, complte with all necessary fitting such as elbows, tees, reducers, serviceable "P" traps etc. and supports such as clamps etc. complate as per specifications. 32 MM DIA

40 MM DIA

Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/ round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as per specification. Thickness 0.63 mm sheet

Thickness 0.80 mm sheet

Thickness 1.00 mm sheet

Thickness 1.25 mm sheet

Supply, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as per specification. Thickness 0.63 mm sheet

Thickness 0.80 mm sheet

Thickness 1.00 mm sheet

Supply, installation & testing of opposed blade GI volume control dampers within ducts to be provided with suitable links, louversand quadrants for manual control of volume of air flow and for proper balancing of the air distribution system.

Supplying & fixing of powder coated extruded aluminium Supply Air Grills with aluminium volume control dampers as per specifications.

Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers complete as per specification

Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminium with aluminium volume control dampers with anti smudge ring & removable core.

Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (class "O") insulation on existing duct after applying two coats of cold setting adhesive (CPR X compound). The joints shall sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specification. 25 mm

Supplying and fixing 50mm thick aluminium foil faced resin bonded fibre glass insulation (on duct) of density 24 kg/cu.m after applying two coats of cold setting adhesive (CPRX compound) sealing all joints with self adhesive aluminium tape & covering with 0.63mmx19mm GI wire mesh netting & butting all joints and laced with GI wire complete and finally covered with one layer of tar felt stuck with hot bitumen as per specification. (for outdoor applications)

Supply, installation, testing and commissioning of GI Volume Control Collar/ duct Dampers Complete with neoprene rubber gaskets. Nuts Bolts, screw linkages, flanges etc., as per Specifications

Supply & fixing Of MS stand for outdoor units

Supply & fixing Of Branch Kit Joints.

SITC Of VRV System including topping R-410 gas as per site requirements. Refrigerant shall be environment Friendly R-410

Supply, Installation, Testing & Commossionig of Control Cum Transmission Wiring in suitable conduits between indoor & outdoor units &for remote including supply of screendwires, Supports, installation, saddles, ties, tags, ferrules, lungs, nuts/bolts/hardware etc.complete in all aspects as per specifications & any other items required to make the system complete. 2C X 1.0 Sq mm Copper

Supplying, Fixing,testing and commissioning of fire dampers in supply air duct/main branch and return air path as and where required of required sizes i/c control wiring,the damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire signal complete as per specification. Fire damper

Actuator and control pannel

Supply, Installation, Testing & Commissionig of flexible {canvas} connection between duct and Machine

Supplying of approved make Hiwall split Inverter type Air Conditioner unit with cooling unit (copper coil) and condensing unit (copper coil) including 5 years compressor warranty and standard length of upto 5 metre of copper piping with insulation etc complete as per specification: 2.0 Ton split type Inverter AC {5 Star}

Installation of split type Inverter/Non Inverter Air Conditioner unit, cooling unit on wall inside and condensing unit on out side wall/ ceiling/ floor at desired locations with existing standard length of copper piping with insulation and power cable including providing and fixing necessary good quality powder coated MS frame etc complete as per specification. (Extra length of copper piping and power cable shall be paid extra on linear basis)

Supply and fixing of approved make wall mounting type voltage stabilizer with input volts 160-250, output volts 200-240 volts and double step relay on desired location with necessary fixing material including connection etc complete as per specification. 5 KVA

Supply, connecting and fixing extra length of copper piping for split type air conditioners of following dia and approved quality with insulation sleave etc complete as per specification 1/2 "

Supplying, connecting and fixing 15mm dia PVC flexible drain pipe (reinforced with nylon threads) in drain outlet of split type air conditioners etc complete as per specification

Providing and fixing following rating motor starter on metal board including, connections, testing and commissioning etc. as per specification. DOL three phase 63 amps

Automatic Star Delta three phase 63 amps

Providing and fixing following rating current transformer in existing cubical panel including, connections, testing and commissioning etc. as per specification. 315/5 amps

Providing and fixing single phasing preventer in existing panel including connection, testing and commissioning as per specification.

Providing and fixing penal mounting following rating analog type ammeter of size 100x100 (NS) in existing cubical panel including, connections, testing and commissioning etc. as per specification. Analog type

Digital type

For ammeter

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as per specification. 63 amps

Fabrication, supply, installation, testing and commissioning of cubicle type compartmentalized wall/ floor mounted power cum control panel board of specified size and following depth made out of not less than 2 mm thick CRCA MS powder coated sheet with suitable size compartments for bus bars, switchgears and necessary cutouts for voltmeters, ammeters etc as per specifications including powder coating painting but without busbars, switchgears and other accessories etc complete as per specification. Above 300 mm and upto 450 mm deep

Supplying and laying following sizes one number FRLS PVC insulated,PVC sheathed, unarmoured, copper conductor control /power cable of 1.1 KV grade on surface/ existing cable tray with 1 mm thick GI saddle as per specification and IS: 694 (2010). 4 x 16 sq. mm

Executive Engineer

Public Work Department

Raigarh Division, Raigarh

Executive Engineer

Public Work Department

E & M Division, Raigarh