PROVN OF GUARD ROOM AND TOILET AT MT GATE AT 166 MTN BDE CAMP IN HASIMARA MIL STN, SPECIAL REPAIR TO BLDG NO T_319 COOK HOUSE AT 166 MTN BDE CAMP IN MIL STN HASIMARA AND PROVN OF 02 AIR CONDITIONER 2 TON WITH STABILIZER FOR COLD ROOM AT MEDICAL INSP

Amount

Surface dressing n exc 15 CM deep for adjoining area in soft/ loose soil complete all as specified

Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft/loose soil complete all as specified

Returning filling in, including spreading, levelling watering & well ramming in layers n.exc 25CUM thick in soft/loose soil complete all as specified.

Removing excavated material (soils) n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified

M&L for PCC (1:4:8) type D2 (using 40mm graded crushed stone aggregate) as in foundation filling and mass concrete complete all as specified.

M&L for fly ash Brick work using modular size bricks curved on plan with mean radius not exc 6m built in cement mortar 1:6 complete all as specified.

M&L for RCC (nominal mix) (1:1.5:3) type A1 (using 20 mm graded crushed stone aggregate) as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc, basement slabs, under reamed piles and mass concrete complete all as specified. Note - Reinforcement and form work shall be measured and paid separately.

M&L for RCC (nominal mix) (1:2:4) type B1 (using 20 mm graded crushed stone aggregate) as in beam, cantilevers, bressummers, lintels over 1.5 m span and similar work complete all as specified. Note - Reinforcement and form work shall be measured and paid separately.

Use and waste of form work to sides and soffits of floor or roof beam, beam hauchings, girders, bressummers, lintels, cantilevers, shelves, for flat rough finished concrete surfaces complete all as specified.

Use and waste of form work to sides of concrete foundation, footings, bases of columns, raft and raft beams sides and soffits (if any) of foundation and plinth beams for flat rough finished concrete surface complete all as specified.

M&L for RCC (nominal mix) (1:1.5:3) type A1 (using 20 mm graded crushed stone aggregate) as in chajjas and similar work complete all as specified. Note - Reinforcement and form work shall be measured and paid separately.

Use and waste of form work to chullah hood, chajjas, troughs and similar items including edges etc for rough finished flat concrete surface complete all as specified.

M&L for Precast cement concrete (1:2:4) type B1 (using 20 mm graded crushed stone aggregate) as in landings, cover slab (for manholes etc) and similar work including necessary form work and set in CUM 1:4 complete all as specified.

M&L for Mild Steel TMT bar 10mm dia and over cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

M&L for Mild Steel TMT bar 6 to 8 mm dia cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

M&L for Mild Steel TMT bar 5mm dia and over upto and including 10mm dia as in stirrups, spacers & binders cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

M&L for rendering (Externally) 20 mm thick in two layer, first layer shall be of 10 mm thick in CUM 1:6 and second layer of finishing coat shall be of 10 mm thick in CUM 1:4 mixed with WPC @200ml per bag of cement on brick work or concrete surfaces of wall and finished even and fair complete all as specified. Note-WPC shall be measured and paid seperately.

Supply only liquid water proofing compound all as specified

M&L for rendering 15 mm thick in CM 1:6 on fair faces of brick or concrete surface of wall and finished even and smooth with out using extra cement complete all as specified.

S&F Structural steel work in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. of Fe 410-W (Gde -E-250 quality- A) Add to any of the foregoing items if structural steel is painted one shop coat of zinc chromate primer paint (including preparation of surface) at Contractor’s workshop before fabrication all as specified

S&F MS Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment confirming to Fe-410-W (Gde E-250 quality B) with riveted, bolted or welded attachment complete all as specified.

S&F mild steel flat iron as in bands straps, supports or stays for rainwater, ventilating pipes including bolt if required, hooks (stay) heavy for large gates,hook and pintle hinges,large hasps and staples, hold fasts, wall ties, hooks for hanging fans ,cleats for securing purlins to wood trusses or rafters and similar SQMall articles conforming to Fe -290 Gde E-165 complete all as specified.

Supply and fix 0.50mm thick prepainted galvalume polyester coated (SQMP coating) coloured metal roofing sheet trapezoidal profile having tensile strength 550Mpa as in roof covering fixed with self drilling screws with EPDM washer etc complete all as specified.

Ditto--- all as per item No 23.00 above but as in eaves board fixed with selp tapping screw as specified.

Supply and fixing as in repairs for aluminium anodised snap grid (605X605mm size) to support the boards / tiles with aluminium Tee section 35 mm x 25 mm x 1.40 mm, cross Tee 23.50 mm x 23.50 mm x 1.40 mm and aluminium angle 25 mm x 25 mm x 1.40 mm as on edge / sides including proper hanging arrangement with 4 mm dia anodized galvanised iron wire with false ceiling iof 4 mm thick E board classic for insulation and accoustic purposes of size 600X600 mm fixed with necessary accessories to frame work or with staples on snap grid upto ceiling proper scafolding arrangementsand with complete all as specified.

-----Blank-----

M&L for Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile laid over and including 15 mm thick screed bed in cement mortor 1:6 complete all as specified.

Ditto all as per serial item No. 27.00 described here-in-before but as in skirting etc fixed over and including rendering/ backing coat 10 mm thick in cement mortor 1:4 complete all as specified.

M&L for non skid ceramic coloured tiles of design as approved by GE 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in vertical surface /skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including rendering 10 mm thick in cement mortor 1:4 complete all as specified.

M&L for coloured joint free non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors, skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with shade of tile laid over and including 15mm thick screed bed in cement mortor 1:6 complete all as specified.

M&L for glazed ceramic colour tiles 450X 350X 7 mm thick as on vertical surface of wall such as skirting, dado, riser etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile fixed over and including 10mm thick rendering on fair faces of brick work or concrete surface in CUM 1:3 for laying wall tiles. approved complete all as specified.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing on SI page No 156 of SSR Part-II complete all as specified.

S&F Solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, supplying and fixing in opening as per specification and drawing on SI page No.160 of SSR Part-II complete all as specified.

S&F mild steel framed work such as grills, gratings etc with ends of bars shouldered and / or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walkways, railings,frame work of watertanks and similar work conforming to Fe -290 Gde E-165 complete all as specified.

M&L for applying two coats of weather proof exterior emulsion paint of standard quality and make, over a coat of white primer including preparation of new /old wall surfaces complete all as specified.

M&L for prepartion of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer after applying 2 coats of cement based wall care putty 1 mm thick each coat to wall surface complete all as specified.

M&L for two coat of synthetic enamel paint over a coat of red oxide on new steel surfaces of any description over 10CUM in width or girth incl preparation of surfaces complete all as specified.

M&L for PCC (1:3:6) type C2 (using 40mm graded crushed stone aggregate), 75mm thick in plinth protection and footpath laid in panels and finished even and smooth without using extra cement including necessary form work complete all as specified. Note : Joints 12mm wide to the full depth of PCC shall be provided at every 3 meters and at every change of direction and shall be filled with mixture of bitumen and sand 1:3 by weight. Cost of this provision shall be deemed to be included in the quoted rate for concrete in plinth protection.

S&F in repair stainless steel curtain rods 20-25 mm dia, anodised aluminium alloy with fixing brackets, stops, and complete fitments all as specified

S&F for pressed steel frames for doors with one or more rebates including necessary lugs, hinges, lock strike plate, etc., complete, as specified, size of frame 125mm x 60 mm x 1.25mm (thick) complete all as specified

M&L for PCC (1:3:6) type C1 (using 20mm graded crushed stone aggregate) as in hold fast block/ copings including necessary form work etc complete all as specified.

S&F 35 mm thick second class hard wood rail and style plain framed factory made panelled shutter (two panel) with lock rail and panel of 9 mm BWP commerical ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (part-I), kiln seasoned and chemically pressure treated complete all as specified.

M&L for Second class hard wood 30 mm thick factory made glazed and skeleton shutters, open rebated and prepared to receive glass , gauze etc with out sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in SSR part I section 8 clause 8.20 (a) complete all as specified.

S&F Butt hinges, medium weight, cold rolled mild steel 100 mm long complete all as specified.

S&F aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy of 250 mm length of bolt complete all as specified.

S&F aluminium handles cast type anodised of 150 mm size complete all as specified.

S&F floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor, over all length of cover plate 140 mm size complete all as specified.

S&F Powder coated anodised aluminium window sliding type three track aluminium sections weighing not less than 0.55 Kg per mtr (Two glazed shutter & one wire mess shutter) including necessary jointing cleats, glazing cleats, rubber packing anodised aluminium snap gridding, screws, handle, locking arrangement etc complete and 5.5 mm thick plain or tinted glass complete all as specified. (Make : Jindal/Hindalco/Indal).

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified.

S&F factory made steel ventilator with top hung shutter including friction/ box type hinges ,steel peg stay complete complete all as specified .

S&F of 150mm long aluminium anodised, barrel tower bolt of extruded section complete all as specified.

M&L for 300 mm Sand filling under floors or in foundations including watering and consolidation complete all as specified.

M&L for 75mm thick PCC (1:3:6) type C2 (using 40mm graded crushed stone aggregate) as in sub-base of floor over and including 50 micron polythene film laid complete all as specified.

S&F wash hand basin, vitreous china, white, flat back (550x400mm) cutting for and pinning ends of brackets(Make:Parryware Code No.-0471,Indus Basin (white) or equivalent and waste fitting,brass chromium plated for glazed ware basin etc with long screwed shanks and fly nuts,flange end bedded in red lead cement and other end fixed 32mm including PVC waste pipe with CP /PTMTcoupling of required length complete all as specified.

S&F CI Nahani trap with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B1 (diameter of outlet 100mm) complete all as specified

S&F angular stop cock made of brass chromium plated screwed both ends for iron pipe for 15mm bore complete all as specified Make: Essco Cat Part No DLX-ESS 526 or equivalent.

S&F Bib tap cast copper alloy, chromium plated with crutch or butterfly handle, screwed down for 15mm bore GI Pipe or for brass ferrule complete all as specified. Make : JAQUAR Code : CON-107 KN or equivalent make as speciifed in list of makes

S&F PVC low level flushing cistern, 10 ltr capacity, syphonic action type white body with inlet ball valve, float , handle, bracket, long flush pipe of PVC to suit flushing cistern ( long bend) etc complete & connecting to WC,complete all as specified (Make : Sleek of Hindware, Slimline of Parryware or equivalent of Cera)

S&F CP brass fittings for wash basins, including mixer tap complete all as specified.

S&F Brass CP mixer for mixing hot & cold water screwed down for iron pipe 15mm bore and fixed complete all as specified.

S&F tubular towel rail 20mm dia D type, Brass Chromium Plated 60 CUM long between flanges complete all as specified.

S&F stainless steel soap dish best quality fixed to plugs with chromium plated brass complete all as specified.

S&F PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified.

S&F Water Closet (squatt pattern) of vitruous china squatting pan of pattern "ORRISA" pattern size 580 x 440 mm white with integral foot rests (excluding flushing cirstern and flush pipe) including connection to trap and flushing pipe anti syphon pipe etc complete including trap set in and incl concrete complete all as specified.

S&F Gun-metal, globe or gate valves,15mm bore with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as direcetd.

S&F swivel shower of CP with shower arm 150 mm size for fixing with 15 mm bore GI pipe complete all as specified.

S&F PVC (SWR) (Bore of pipe 110mm) pipes single socketed, in any length with rubber ring joints fixed to walls with necessary clamps, bolts etc complete all as specified.

S&F PVC (SWR) bends any radius fixed to PVC Pipes/Steel Gutters (Bore of pipe 110mm) complete all as specified.

S&F PVC (SWR) vent cowl fixed to PVC Pipes (Bore of pipe 110mm) complete all as specified.

S&F 15 mm bore steel tubing medium grade, galvanised fitting fixed complete to walls and ceiling or floor complete all as specified.

S&F 20 mm bore steel tubing medium grade, galvanised fitting fixed complete to walls and ceiling or floor complete all as specified.

S&F 1000 ltrs capacity rotational moulded polyethelene water storage tanks (cyclindrical vertical with closed top) triple layered incl connecting up pipes securing access covers etc as complete all as specified.

S&F 20 mm dia PVC ball cock (PVC float valves) complete high pressure of PTMT with epoxy coated aluminum rod and high density plastic ball screwed for iron pipe and fixed as required to use reducer and check nut complete all as specified.

M&L for PCC (1:3:6) type C-2 (using 40mm graded crushed stone aggregate) as in surface channels and drains complete all as specified.

M&L for Anti termite treatment to the top surface of filled earth at the rate of 5 LTRs of emulsion per SQM of surface complete all as specified.

M&L for Anti termite treatment to the backfill in contact with foundation at the rate of 7.5 LTRs of emulsion per SQM of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified.

M&L for Anti termite treatment to the soil under plinth protection at the rate of 5 LTRs of emulsion per SQM of surface area complete all as specified.

M&L for Anti termite treatment to the soil along with external perimeter of building at the rate of 2.25 LTR of emulsion per metre of the perimeter wall complete all as specified.

M&L for brickwork with burnt fly ash old size bricks straight or curved on plan exc 6mtr mean radius built in cement mortar 1:6 by using old size bricks complete.

M&L for 20mm thick rendering in cement mortar 1:4 on other than fair faces of brick or concrete surface finished even and smooth with using extra cement complete all as specified.

M&L for cement concrete (1:2:4) type B1 (using 20 mm graded crushed stone aggregate) as in bed plates, kerbs, water troughs and the like including weathering, slightly rounded for chamfered angles and throating, complete all as specified.

S&F reinforced concrete pipes, class NP2, drain pipes of 150mm bore laid in trenches and jointed with collars complete all as specified.

M&L for concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; in cement concrete (1:3:6) type C2 (using 40 mm graded crushed stone aggregate) complete all as specified.

Surface excavation n.exc (not exceeding) 30 CM deep and averaging 15CUM deep and getting in soft/loose soil complete all as specified.

Removing excavated soils and material exc. 250 m but n exc. 500 m and depositing where directed complete all as specified.

M&L for 100 mm thick cement concrete (1:4:8) type D2 (using 40 mm graded crushed stone aggregate) as in path/ steps laid with and incl use and waste of form work and finishing the surface even and rough to receive the topping layer or tilling complete all as specified.

M&L for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified.

Dismantling timber scantlings 40 sqCUM and over in section as in framed work in any position complete all as specified.

Dismantling wall and ceiling Boards (Fiber, pulp, Insulation etc) or insulation Board/ slab/ blankets any thinkness including cover fillets complete all as specified.

Demolition of reed, lathing, single or double, including battens and plaster or chicken wire lathing complete all as specified.

Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified.

Taking down chowkats or frames area not exc 1.5 Sqm each with shutters (with out taking off shutters from the frames) complete all as specified.

Taking down chowkats or frames area exc 1.5 sqm but not exc 4.0 Sqm each with shutters (with out taking off shutters from the frames) complete all as specified.

Taking down cement plaster on wall of any description including racking out joints, hacking for key and scrubbing down with water etc complete all as specified.

M&L for PCC (1:2:4) type B2 (using 40mm graded crushed stone aggregate) as in foundation filling and mass concrete complete all as specified.

M&L for rendering 10 mm thick in CM 1:6 on fair faces of brick or concrete surface of wall and finished even and smooth with out using extra cement complete all as specified.

S&F steel work in Hollow section Square/rectangular as in roof truss, purlin, rail etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St -240 and painted one shop coat of zinc chromate primer paint including preparation of surface at contractor workshop before fabrication complete all as specified.

S&F Mild steel bolts, purpose made, with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut exc 30CUM long complete all as specified.

M&L for 6mm thick non asbestos fibre reinforced standard designer cement building boards fixed or laid/ inserted to timber/ GI/ Aluminium framework with screws complete all as specified

Demolition of cement concrete un reinforced in ground floor and paving n exc 15CM thick (below or above ground level) complete all as specified.

M&L for 40mm thick PCC (1:2:4) type B1 (using 20 mm graded crushed stone aggregate) as in floor finishes, finished even and smooth without using extra cement complete all as specified.

M&L for non skid ceramic coloured tiles of design as approved by GE 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed in cement mortor 1:6 complete all as specified.

M&L for non skid ceramic coloured tiles of design as approved by GE 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in vertical surface /skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including rendering 10 mm thick in cement mortor 1:4 complete all as specified.

S&F 40 mm thick Flush shutters, solid core construction, with block board core and two face is covered with decorative face veneer with lipping/frame to match complete all as specified.

S&F 35mm thick second class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. and divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specfied

Providing and fixing factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm 52mm), sliding sash (42mm x 67mm). Slidingmesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of wateretc., making arrangement for fixing of hardware.EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated),steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories.

M&L for 5mm thick sheet tinted glass n exc 0.50 sqm in area to be fixed in UPVC windows complete all as specfied

M&L for preparation of new plastered surfaces and applying of two coats of cement base paint on wall surfaces complete all as specified

M&L for applying two coats of acrylic distemper on newly plastered wall surface including preparation of surface over a coat of 1mm thick Birla wall care putty complete all as specified.

M&L for preparation of new or previously untreated surfaces of wood and wood based surfaces of any description, over 10 CM in width or girth and apply two coat of synthetic enamel paint over a coat of pink primer complete all as specified.

M&L for prepolished coloured with grey pigments chequered cement concrete tiles 25 mm thick confirming to IS - 13081, 1993 with grey cement and no pigment set, jointed and pointed in neat cement slurry over and including 15mm thick screed bed in cement morter 1:6 complete all as specified. (Make- Lovely or equivalent make)

Taking up or down 20 mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified.

Taking up or down 15 mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified.

Supplying and laying of CPVC pipes 16mm dia, SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Supplying and laying of CPVC pipes 20mm dia, SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Demolition of stone slabs and tiles of any description or thickness in floors, etc laid bedded and pointed in any mortar complete all as specified.

M&L for Granite Stone Slabs of 18 to 20 mm thick of Colour Mexican Red / Ruby Red / Z Black / Pearl Black as in Floors, Treads of Steps, Window Cills, Cooking Platform etc. with machine cut edges, Table rubbed and prepolished to smooth mirror finish all to required sizes, granite stone slabs shall be of design / pattern as directed, including diagonals, inlays, borders, margins in two or more colours / shades, designs / patterns of stone slabs, set and bedded with grey cement [slurry] and jointed and pointed flush using polymer based cementitious tiling joint filler to match the shade of the Granite Slabs including screed bed or bedding layer of mortar 20 mm thick in Cement Mortar 1:4 complete all as specified.

S&F in repairs sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified.

M&L for complete removal of existing treatment of old plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer after applying 2 coat of cement based wall care putty 1 mm thick in each coat including complete removal of existing treatment complete all as specified.

M & L for complete removal of existing treatment and finishing the walls with two coats Acrylic smooth exterior emulsion paint of required shade for New work over and including priming one coat of exterior primer applied all as per manufacturer's specification and as specified.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc for taking credit ( credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified.

M&L for point wiring complete with 1.5 Sqmm multistranded copper conductor single core PVC insulated unsheathed FR-LS cable 1100 volts grade (ISI marked) with proper colour coding drawn through and including non-metallic rigid PVC medium grade conduit not less that 20mm dia and conduit accessories (ISI marked) concealed in wall/fixed to roof, ceiling etc including provision of 1.5 Sqmm PVC insulated multistranded unsheathed copper conductor cable FR-LS (ISI marked) as earth continuity conductor connected to common earth dolly, fabricated sundn terminal box made out of GI sheet steel not less than 1.22 mm thick for boxes upto a size of 200 x 300mm and above this size not less than 1.63 mm thick duly painted with aluminum inside and anticorrosive paint outside, concealed in walls, with 3mm thick bakelite/plastic laminated sheet top cover fixed with cadmium plated iron screws for housing switches, socket outlets, fan regulators etc duly earthed including cutting chases of existing wall for conduits and sinking for boxes and making good to the disturbed surface of wall/floor and matching with existing specifications. Connections of cable with MCBs or bus bar shall be sone through proper size copper/brass thimbles. Where concealing of conduit is not feasible ie on surface of roof etc, conduit shall be fixed on surface with necessary saddles at no extra cost complete all as specified :-

One light point controlled by one way switch 5/6 amps.

One ceiling fan/Exhaut fan point controlled by one way switch 5/6 amps complete all as specified.

One socket out let 5/6 amps point on the same board complete all as specified

One socket out let 5/6 amps point on the independent board complete all as specified

All as per item No 127 above but wiring with 2.5 sq mm single core copper conductor for one socket out let 15/16 amps point on the independent board complete all as specified.

S&F switch piano flush type 5/6 amps single pole one way complete all as specified.

S&F socket 2 in 1, 3 Pin, 5/6 amps, white ivory finish flash type complete all as specified.

S&F of socket outlet 2 in 1, 5 Pin, 5/15 amp, multipurpose 230 volt flash type complete all as specified.

S&F switch piano flush type 15/16 amps single pole one way complete all as specified.

S&F ceiling rose, bakelite, surface type, 220/240 volts, three terminals complete all as specified.

S & F lamp holder, insulated body, with back plate suitable for batten/angle fittings complete all as specified

S & F deluxe fan electronic regulator not less than 80 watt, 230 volt, AC, 50 Hz rotary step white/ivory finish complete all as specified.

S & F IP-20, class I, LED tube light fittings 20W (or nearest next higher wattage) (4feet), wall/surface mounted, integrated type with aluminimum housing and decorative and caps with integrate high efficiency electronic driver and surge suppressor of 5KV or more, luminaire efficacy> 120 lumens/watt, power factor > 0.90 operating range-140 to 270/V, 50Hz fixed with 02 Nos of PVC round/ squre blocks, screws etc complete with all accessories internally prewired and connecting up with three core PVC cable of copper conductor of size 23/0.0076 and making conncetion complete all as specified

S&F LED recessed mounted light 600mm x 600mm) 35/36W suitable for indoor with integrated high efficiency electronic driver and surge suppressor of 5KV or more, luminaire efficacy >120 lumens/watt, power factor> 0.90operating range-140 to 270 V, 50Hz fixed with 02 Nos of PVC round/squre blocks, screws etc complete with all accessories internally prewired and connecting up with three core PVC cable of copper conductor of size 23/0.0076 and making connecting complete all as specified

S & F LED street light fittins 35 watt in 230 VC outdoor type with high pressure die cast aluminimum housing, heat resistant, toughed glass cover with IP-66 proction SPD> 7.5 KV, efficacy > 120 lumen per watt, internally prewired and connecting up with three core PVC cable of copper conductor of size 23/0.0076 and making conncetion complete all as specified.

S&F Sheet metal enclosure for 8 way Distribution Boards (DB’s), double door, single pole & neutral with minimum 100 amps rated bus bar, IP-43 protection grade protection suitable for fixing MCB"S/lsolators complete including taking down the old one complete all as specified.

S&F MCB Triple pole & neutral, 63 amps, 415 volts, ‘C’ curve, 10 KA all complete including taking down the old one complete all as specified.

S&F MCB, Single pole & neutral 6 to 32 amps, 240 volts, ‘C’ curve, 10 KA all complete including taking down the old one complete all as specified.

S&F MCB, Single pole, 6 to 32 amps, 240 volts, ‘C’ curve, 10 KA all complete including taking down the old one complete all as specified.

Taking down carefully by unscrewing from boards/ outlet boxes, fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, brackets, ceiling fittings, bulk head fittings, tube light fittings and regulators, etc. complete all as specified.

M &L for Earthing complete with GI earth plate electrode 600x600x6mm thick buried directly in ground (Earth pit not less than 2.25M deep below normal ground level) with top edge of the plate not less than 1.5m below normal GL. Connected to galvanized earth lead wire 4mm dia by means of nut, bolt, check nut and washers including necessary excavation and earth work in soft/loose soil, GI protection pipe light grade 15mm bore for protecting the GI wire mesh funnel alternate layer of charcoal dust, and salt PCC pit 1:3:6 type C1 using 20mm graded stone aggregate and 50mm thick RCC 1:2:4 type BO using 20mm graded stone aggregate cover re-inforced with 8 mm dia MS TMT bars 80mm C/C both ways complete all as specified and shown in Electrical plate No.3 SSR part-1 and connected to the earth point and testing complete including taking out the old one complete all as specified.

M & L Sub main wiring concealed type with two run single core cable PVC insulated cable with 4.0 Sqmm (Nominal area) multi stranded copper conductor FRLS cable 1100 volts gde incl earth continuity conductor using PVC insulated cable of stranded copper conductor of size 4.0 Sqmm connected to common earth dolly and drawing into rigid PVC conduits of 25 mm dia medium grade size, making good the disturbed surfaces complete all as specified.(NOTE : Two run of submain wiring cable alongwith one run of earth wire shall be measured as one length. .

M&L for street light bracket made out of GI pipe light grade 25 mm dia 1.2 mtr length bent to shape and reduced to required size at top upto 1.2 mtr length by cutting, welding and well finishing including MS clamp of flat iron of size 25 x 5 mm suitable length 2 Nos complete with drilling hole, fixing with runts bolts and washers including painted with two coats aluminium paint over a coat of red oxide primer complete all as specified.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 2 core all fixing and connecting accessories such as cable lugs, cable glands, nut, bolts, complete all as specified.

M&L for sand cushioning in cable trenches over & under the cable, with river washed coarse sand, as per standard practice with proper compaction complete all as specified. (Punned thickness 18 CUM shall be considered for payment as per para 19.75 of SSR Part-I)

Supply and laying for brick protection for protection of cable over sand cushioning cables inside the trench by using common brunt clay building bricks sub-class “B” old size brick and flat and width wise along the axis of the trench complete all as specified.

Supply and fixing 40 mm dia GI tubing medium grade ISI marked laid in trenches / laid under floor for protection of cable including all fittings such as elbow, bends, etc and short length complete all as specified.

Taking up or down steel tubing in trench/ wall with connection including cleaning for removal all as specified for the 20 mm dia bore

Supply and lay pipe galvanized, “Medium class”, including fittings 20 mm complete all as specified.

Supply and fix Gun metal ,globe Gate Valves with iron wheel head of 20 mm dia bore complete with all accessories all as specified.

M& L for cutting existing GI pipe alteration or addition of 40/50 mm dia bore for inerstion of reducer Tee complete with all accessories all as specified.

M&L for point wiring complete with 1.5 Sqmm multistranded copper conductor single core PVC insulated unsheathed FR-LS cable 1100 volts grade (ISI marked) with proper colour coding drawn through and including non-metallic rigid PVC medium grade conduit not less that 20mm dia and conduit accessories (ISI marked) concealed in wall/fixed to roof, ceiling etc including provision of 1.5 Sqmm PVC insulated multistranded unsheathed copper conductor cable FR-LS (ISI marked) as earth continuity conductor connected to common earth dolly, fabricated sundn terminal box made out of GI sheet steel not less than 1.22 mm thick for boxes upto a size of 200 x 300mm and above this size not less than 1.63 mm thick duly painted with aluminum inside and anticorrosive paint outside, concealed in walls, with 3mm thick bakelite/plastic laminated sheet top cover fixed with cadmium plated iron screws for housing switches, socket outlets, fan regulators etc duly earthed including cutting chases of existing wall for conduits and sinking for boxes and making good to the disturbed surface of wall/floor and matching with existing specifications. Connections of cable with MCBs or bus bar shall be drawn through proper size copper/brass thimbles. Where concealing of conduit is not feasible ie on surface of roof etc, conduit shall be fixed on surface with necessary saddles at no extra cost all as specified and as directed for the following :- (a) One light point controlled by one way switch 5/6 amps.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm and provision of 3 core flexible multistranded copper conductorof size 0.75 Sqmm from ceiling rose to fan all as specified.

Supply and fix of ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC)

Supply installation, commissioning and testing of electric water heater, storage vertical type, BEE 5 star rated 25 ltrs capacity 230 volts AC 50 Hz comprising of high wattage heating element minimum 2KW for quick heating extra thick SS inner tank of superior 304 grade,rust & shock proof ABS outer body, non-ferrous pressure plate with and including provision of 04 Nos grouting bolts suitably flush to wall or any other surfaces and connection pipe for hot and cold water supply 25 lts BEE 5 Star rated complete stranded copper conductor cable/ flexible chord complete all as specified.

M&L for GI water tubing medium grade 15 mm dia fixed on wall with all fittings and fixtures complete all as specified.

Supply and install hi wall split units indoor/ outdoor complete with cordles remote control unit with in built plasma filter for better indoor air quality with minimum 3 star rating of capacity 2.0 TR incl out door mounting bracket complete all as specified.

M&L point wiring with FRLS PVC insulated unsheathed multistranded copper conductor,conforming to IS-694 of size 4 sqmm nominal cross sectional area single core drawn in and including 25mm size 'medium grade' PVC doubled lock Casing-Capping and fittings, including, pressed steel concealed terminal switch boxes not less than 1.2mm thick of reqd size factory made duly painted inside and outside with two coats of black bituminous paint over one coat red oxide primer, 3mm thick plastic laminated sheet top cover (ISI Marked) fitted with chromium plated brass screws & washers complete including 4 sqmm nominal cross sectional area PVC insulated unsheathed multistranded copper conductor green as earth wire connected to earth dolly with all accessories complete all as specified.

S&F MCB distribution boards (DBs) with sheet metal enclosure, single door, IP 43 protection, 240 Volts,2 way, single pole and neutral, with 200 Amps rated copper bus bar (as per OEM), neutral link, ertth link earthing studs, suitable for fixing MCBs, without MCBs fixed flush to wall/other surface complete all as specified.

M&L sub main wiring concealed type with two run single core cable PVC insulated cable with 4.0 Sq mm(Nominal area) multi stranded copper conductor FRLS cable1100 volts gde earth continuity conductor using PVC insulated cable of standed copper conductorof size 4.0 Sq mm connected to common earth dolly and drawing into rigid PVC casing-capping of 25 mm dia medium grade size,making good the disturbed surface complete all as specified. NOTE:- One unit length shall measured as two run of main wire and one run of conduit & earth wire.

Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 5 KVA Make- Miracle/ V- guard OR equivalent make as approved by GE.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 2 core all fixing and connecting accessories such as cable lugs, cable glands, nut, bolts, complete all as specified.

M & L for boring of horizontally holes by manual method under road beloe 1 meter from the road surface and dia of hole not exe 80mm without damaging the existing road getting out and disposal of excavated soil,etc to a distance not exc 50meter from the site of work complete all as specified.

M/S SARDAR MAL NAHATA (BID ID -3426516)

BHARAT ELECTRIC (BID ID -3426529)

M/S ROY ENTERPRISE (BID ID -3426535)