ADDN / ALTN TO BASKET BALL COURTS, TENNIS COURTS AND TRG SHEDS IN NORTH CAMPUS AT IMA DEHRADUN

Amount

BUILDING WORKS

Demolition of cement concrete (unreinforced) , in ground floor and paving n.exc. 15 cm thickness (below or above ground level) complete all as specified and directed.

Demolition of cement concrete (unreinforced) , in ground floor and paving exc. 15 cm thickness below or above ground level complete all as specified and directed.

Demolition of brick work or stone/boulder masonry built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed.

M&L for brick work in CM (1:4) using sub class 'B' old size bricks straight or curved on plan exceeding 6.0 meter mean radius complete all as specified and directed.

Taking down cement plaster on brick or stone walling including raking out joints hacking for key scrubbing down with water etc complete all as specified and as directed.

M & L for 15mm thick rendering in cement mortar (1:4) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed.

M & L for Hardcore of broken stone or boulders of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 150 mm thick, watered and rammed to a true surface complete all as specified and as directed.

M & L for 75mm thick plain cement concrete type D-2 (1:4:8) (using 40 mm graded stone aggregate) as in sub bases complete all as specified and directed.

M & L for PCC type D-2 (1:4:8) (using 40mm graded stone aggregates) as in foundation filling and mass concrete complete all as specified and directed.

M&L for 40 mm thick plain cement concrete type B-1, (1:2:4) (using 20 mm graded stone aggregate) as in floor etc, finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed. Note :- Slope of 1 inch in every 10ft on short side of the court shall be maintained.

M&L for cement concrete type B-1, (1:2:4) (using 20 mm graded stone aggregate) as in cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork complete all as specified and directed.

Supplying and fixing basket ball pole with Acrylic / Fibre glass basket ball board as per manufacturer code instructions over existing foundation and foundation bolts complete all as specified and directed. Make : Stag, Product code - BBSE 31/ Hercules / Bajaj / Vinex. Note : Contractor shall get the make and design of the Pole and accessories approved from the Engineer-in-Charge.

M&L for 25 mm thick sand layer under interlocking paver block complete all as specified and directed.

M&L for Machine pressed precast concrete interlocking paver block (Polished) any shape and size confirming to IS 15658-2006 of M-35, 60mm thickness with grey cement and pigment as in roads berms complete all as specified.

Supplying and fixing plastic dividing strips 1.5 mm thick, 38 mm wide and inserted in position, conform to design, complete all as specified and directed.

Finishing with Epoxy paint (two or more coats) at all locations, prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface etc, complete on concrete work all as specified and directed.

M&L for fixing of ITF approved international standard removable tennis net post size 80 mm x 80 mm with net of nylone complete all as specified and directed. Make : Ebaco India Ltd Bengaluru / Hercules / Bajaj / Vinex.

Supply and installation of ITF Certified 9 Layers Synthetic Acrylic System of American/European/Australian origin only for Basket ball court flooring complete of following specifications:- 1 x Acrylic Resurfacer ( Minimum consumption 0.3 Kg per Sqm ) - 3 Granular Cushion layer ( Minimum consumption 0.72 Kg Par Sqm for each Layer ) 3 Latex Smoothing Cushion layer ( Minimum Consumption - 0.45 Kg per Sqm for Each Layer ) 2 textured topcoat. ( Minimum consumption - 0.3 Kg Per Sqm For Each Layer ) 9 Layer US OPEN colours topcoat – Blue Inside/Green Outside. 1. The Playing Surface should be currently an official surface for an ATP Grand Slam/ ATP Masters 1000 Series ( At the time of the bidding of the tender ). Documentary proof to be submitted at the time of technical bid submission 2. The Material Should be Premixed from the Manufacturer's factory ( Place of Origin) 3. Mixing of Silica Sand on site for Cushion and Colour Coats will not be permitted. 4. All material should be directly imported for this project. Stock material will not be allowed. Contd...

5. Manufacturer to give declaration of consumption ration on letter head 6. The manufacturer to give proper Technical Data sheets verifying the above consumption Ration 7. Tool required for Application of the above system to be procured from Manufacture of Synthetic Acrylic only ( Like Squeezy , Line marking tool , etc ) 8. Line Marking Material to be of Same brand as Synthetic Acrylic Surface 9. Bidder to provide warranty of 5 years 10. The product Should be an ITF Pace Rated material. Manufacturers details and the product details should be listed on the ITF pace rating website. Bidder to provide a snapshot of the listing on the ITF website of the proposed product of a date not less than 15 days from the submission of the technical bid. 11. The ITF pace rating certificate for the Manufacturer and product proposed should be valid for more than 3 months from the date of submission of technical bid. Bidder to provide all proofs for the same. 12. The pace rating certificate from ITF of the product proposed to be submitted by the Bidder along with the technical Bid. 13. The manufacturer should be an ISO 9001-2015 certified company. 14. The Product Proposed should be of European / American / Australian region only. The manufacturer to give a declaration of the same. Contd...

15. The material to be order and manufactured specifically for the said project. Manufacturer’s declaration to be provided. Notes: (i)Slope of 1inch in every 10ft on short side of the court (ii)Minor Broom Finish Base with good surface to ensure no water logging. (iii)The rubber granules/crumb/powder should be pre-mixed by the manufacturer before importing. This ensures there is no human error / installing error while mixing of material. (iv)The manufacturer should have minimum 3 systems classified by International Basket ball/Tennis Federation. All certificates shall be uploaded and attached with the tender documents. (v)The validity of these certificates should be minimum 36 months to ensure latest product is being supplied. (vi)Item shall be executed directly through authorized OEM of manufacturer only and manufacturer has to give the guarantee for at least 05 years against peeling, cracking and sagging. 5% of the quoted amount against Item No.19 above shall be retained out of contractors final bill as security deposit for the guarantee period of 05 years which shall be refunded to him after expiry of the guarantee period Satisfactorily. (vii) The OEM shall deploy the applicator manpower only, who have provident fund account. MAKE:- LAYKOLD / DECOTURF / PLEXIPAVE / GREENSET.

BLANK

Excavating in post holes (or similar holes) each n exc 0.5 cum in soft/loose soil and getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance n exc 50 mtr. complete all as specified and directed.

Dismantling posts and struts (wood, steel or RCC) any section, including taking out embedded portion in concrete and making good disturbed ground complete all as specified and directed.

Dismantling expanded metal, any thickness or mesh, fixed with steel or wood fillets, if any, n. exc 4.00 Kg/Sqm complete all as specified and directed.

M & L for PCC type C-2 (1:3:6) (using 40mm graded stone aggregates) as in foundation filling and mass concrete complete all as specified and directed.

S&F MS work for posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, wind ties, etc.; flat iron fillets ( for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 290 Gde E-165 complete all as specified and directed.

Supply only chain link fencing, PVC coated galvanized steel of size not greater than 50mmx50mm complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and directed.

S & F of Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 5cm but n. exc. 10 cm long & dia of neck 11 to 15 mm complete all as specified and directed.

M&L for preparation of new steel surfaces of any desciption, over 10 cm in width or girth, not otherwise described and applying two coats of synethic enamel paint over a coat of red oxide primer complete all as specified and directed.

BLANK

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth in soft/loose soil for laying/taking out under ground cable and other works and getting out the excavated soil complete all as directed.

All as per srl No. 31 as above but for depth exc 1.5 mtr but not exc 3.00 mtr complete all as specified and directed.

Returning, filling in trenches including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick in soft/loose soil after cable laid and testing complete all as directed.

Removing the excavated soil to a distance not exceeding 50 m and depositing where directed at a level not more than 1.5 m above the starting point complete all as directed.

M&L for sand cushioning to LT UG cables (8 cm deep before laying of cable and 15 cm deep over the cable) with clean, dry and unwashed sand free from sharp particles including gently punning around cable complete all as specified and directed. Note :- Punned thickness only will be considered for payment.

M&L for un-reinforced precast concrete cable cover LV type I, flat size 250 mm X 150 mm X 40 mm as protection to underground cable laid dry and flat adjoining each other complete all as specified and directed.

M&L for PCC type B-1 (1:2:4) (using 20 mm graded crushed stone aggregate) as in coping of poles/stays including form work and dismantling of existing PCC complete all as specified and directed.

M&L for cement concrete (1:4:8) type D2 (using 40 mm graded stone aggregate) for foundation of pole/stay including form work and dismantling of existing PCC complete all as specified and directed.

M&L for galvanised steel tubes light grade 40 mm bore with fittings laid for protection of cable under road crossing fixed to walls or pole complete all as specified and directed.

M&L for galvanised steel tubes light grade 50 mm bore with fittings laid for protection of cable under road crossing fixed to walls or pole complete all as specified and directed.

Supply and fix LED sport lighting Floodlight luminaire with a housing of non-corrosive high pressure ADC with corrosion resistant powder coating and Anti-dust exposed Lens to ensure protection. The luminaire should have CRI > 70, SDCM <5 and CCT of 5700K and shall be compliant with IP66 and IK08 classification. Luminaire shall be designed to emit at least 23500 nominal lumens with maximum system wattage of 195W at a system efficacy of atleast 120 lumen/watt. The luminaire shall be designed so as to ensure lumen depreciation of up to 30% over 50k burning hours @ design ambient temp 35 deg C. The luminaire should have asymmetrical wide beam suiting sport applications with exposed PC optic lens. The luminaire should have fins on the back to ensure good heat dissipation and to prevent dirt from settling on the luminaire along with aiming angle scale. The electronic driver should be fully integrated and shall have a power factor >0.95 and THD <10% with a minimum inbuilt surge protection of 4kV/kA and suitable for an operation voltage range of 140-270V AC.

The driver should be BIS approved, fully potted and encapsulated with 440V Stress Voltage protection for 8 Hrs. High Cut off : 325V(+/- 15V) and Auto Restart function should also be available within the fixture. The luminaire should comply with all the required IEC and IS standards and Marine Salt Protection (1000-hr test in lab). Make :- Philips BVP483LED235 CW AWB PSU GR/Havells, JETAVALOURFL 200W LED757MODWBLTG/OSRAM LUXPOWER FLOOD LIGHT 190W CWFS1 IN. Note:- The contractor shall purchase this item direct from authorized dealer and produce original purchase voucher and test certificate to the Engineer-in-Charge and also give minimum three years warranty from manufacturer of the product.

Supply and fix pole mounted LT junction box, Water proof and fire proof, sheet moulding compound (SMC) box of inside size 250 mm x 200 mm x100 mm deep complete with 4 nos terminal end aluminium strip of 20 x 4 mm size fixing cable end terminal and 3 nos MS bolts and nut of size 8 mm dia x 30 mm long and MCB mounting rail with 6 Amp MCB SP duly welded with box fixed on plle with MS clamp 25 mm x 3 mm MS strip duly painted and testing including taking down existing complete all as specified and directed. Make : Sintex / L&T / Universal.

M&L for bus bar chamber pedestal type of size 90 cm x 60 cm x 50 cm out door dust & vermin proof front opening made out of 2.0 mm thick MS sheet duly painted and consisting with aluminium bus bar 3 phase and neutral 4 Nos 400 Amp fixed on insulators and one MCCB FP 200 Amp, 25 KA rupturing capacity - 01 Nos (Main incoming) and MCB TPN 100 Amps 10 KA -04 Nos (outgoing) including fixed in PCC 1:3:6 using 20 mm graded stone aggregate including danger plate etc including taking down existing LT feeder bus bar complete all as specified and directed.

M&L for bus bar chamber pedestal type of size 90 cm x 60 cm x 50 cm out door dust & vermin proof front opening made out of 2.0 mm thick MS sheet duly painted and consisting with aluminium bus bar 3 phase and neutral 4 Nos 200 Amp fixed on insulators and one MCCB FP 100 Amp, 16 KA rupturing capacity including fixed in PCC 1:3:6 using 20 mm graded stone aggregate including danger plate etc including taking down existing LT feeder bus bar complete all as directed.

Supply, laying, jointing and testing XLPE insulated, armoured heavy duty under ground electric cable with stranded aluminium conductor 1100 volts grade including taking out/down old existing unserviceable cable of following sizes : Note: Excavation, sand cushioning & cable cover shall be measured and paid separately under respective items of this schedule.

(a) 50 Sqmm, 3.5 core.

(b) 16 Sqmm, 4 core.

(c) 6 Sqmm, 2 core.

M&L for PVC wire with copper conductor 1100 Volts grade Cross section area of size 1.5 Sq mm 3 Core laid in trenches/pole complete all as specified and directed. Make : Gloster / Havells / Polycab.

M&L for steel tubular swaged pole 11 mtr long with cast iron base plate, finial taper plug, bolts, nuts and screws as specified type 410 SP 55, including painting with anti corrosive paint internally complete and externally complete with two coat of synthetic enamel aluminium paint over a coat of red oxide primer and preparation of surface including marking of pole Nos with black paint complete all as specified and directed.

M&L for MCCB 200 Amps 4 pole 415 volts with rupturing capacity 25 KA with thermal magnetic release and adjustable overload setting having including taking out existing unserviceable MCCB complete all as specified and directed. Make: Legrand, L&T, ABB, Schneider.

M&L for Earthing complete for machinery equipment installed at power house/sub station with galvanized iron earth plate electrode 600 mm x 600 mm x 6 mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) vertically, with top edge of plate not less than 1.5 metre below normal ground level connected to GI strip 25 mm X 4 mm main earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron and protected with 40 mm dia light grade GI pipe all as shown in electrical plate No 3 of MES Schedule Part-I connecting to earthing test point & to main switch board and testing on completion with and including necessary excavation and earth work in any type soil, earth lead connected to earth test point & to main switch board etc with & including adequate quantity of charcoal dust and common salt, test point, PCC (1:3:6) type C-1 (using 20 mm graded crushed stone aggregate) for earth pit with 40 x 40 x 6 mm mild steel angle iron frame for cover, internal surface of concrete shall be given 10 mm thick plaster in CM 1:4, pre cast RCC (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) 40 mm thick cover, reinforced with 8 mm dia deformed or TMT bars 3 Nos both way with 12 mm dia round bar handle, GI medium grade watering pipe 20 mm dia with funnel and wire mesh and 40 mm dia GI light grade earth lead protection pipe etc complete all as specified and directed.

Note : (i) Earth strip and its protection pipe for any required length is included under the quoted rates. (ii) Any joints in earth lead from earth electrode to test point shall not be allowed/permitted. (iii) If the desired earth resistance is not found within permissible limit shall be re done by contractor at no extra cost.

M&L for Rolling and consolidating formation surfaces in cutting with power roller exc 8 tonne but n exc 12 tonne capacity complete all as specified and directed.

M & L for two coats of cement base paint over a coat of primer on new surfaces of walls etc complete all as specified and directed.

M & L machine cut kota stone slab flooring 18-20mm thick section n. less than 0.36 Sqm, laid over cement screed base 20mm thick in CM(1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and directed.

M & L for 75 mm thick Cement concrete type C-2, 1:3:6 (40mm graded aggregate) as in sub base of floor complete all as specified and directed by Engineer in Charge.

M&L for moorum/ red bajri filling in floors or pavings laid in layers n exc 15cm thick spread levelled and rammed including watering etc complete all as specified and directed.

Note : Tenderers may note that amount of credit Rs 3,05,240.00 will be deducted from the total amount arrived, at the time of Acceptance of contract.

DEVKI NANDAN ASSOCIATES

J.D.Builders