SPECIAL REPAIR TO BLDG NO NP 6/1 TO 04 OR MD ACCN OF 891 FD REGT AT ALHILAL MIL STN

Amount

Demolition of brick work or stone /boulder masonry, built in CM, incl all quoins, arches, pillars etc but excluding ashlar facing, dressed stone work and precast concrete articles etc, complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and in pavings not exceeding 15 cm thickness (below or above ground level), complete all as specified and directed.

Dismantling wall and ceiling board (fibre, pulp, insulation etc) or insulation boards / slabs / blanket, any thickness including cover fillters complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge and thickness in roof covering including Nainital or similar pattern roof coverings, complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided, complete all as specified and directed.

M&L brick work with sub class 'B' bricks straight or curved on plan, exceeding 6 m mean radius with old size bricks, built in cement mortar 1:6 complete all as specified.

RCC M-15 (Nominal mix), type B-1 (using 20mm stone aggre) as in slab supported on walls, beams and columns in floors, roofs, landing, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed. Note: Reinforcement used shall be measured and paid separately under relevant item.

Form work to sides and soffits of suspended slab, such as roof slab, floor slab, landing and similar work n.exc. 200mm thick (horizontal or sloping) for fair finished surfaces, complete all as specified and directed.

M&L plain cement concrete, M-10 (Nominal Mix) type C-1 (using 20 mm graded crushed stone aggregate) as in surface channels or drains etc, complete all as specified.

M&L extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc, complete, all as specified .

2nd class HW (Sal / Hollock) factory made, plain framed, panelled shutters (two panels) 35mm thick with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneers on both faces. The size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated, 35mm thick fitted to chowkats, complete all as specified and directed.

2nd cl HW (Sal / Hollock) factory made glazed and skeleton shutters 35mm thick, open rebated and prepared to receive glass or gauge, etc. (w/o sash bars) edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing gauge sizes of members of shutters as specified in SSR Part-I Section-8, clause 8.24 (a) for door shutters S&F to chowkats, complete all as specified and directed.

Galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised wire staples, complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) n.exc. 1.50 sqm each, and removing from site, complete all as specified and directed.

Taking down chowkats or frames with shutters (w/o taking off shutters from the frames) exc. 1.50 sqm but n.exc. 4 sqm each and removing from site, complete all as specified and directed.

Factory made solid panel PVC door shutter 30mm thick (stile) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rails and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to in stiles & rails with suitable PVC sheet beading and joinned together with solvent cement S&F in frames at site as per specification and drawing shown in SSR Part-II, complete all as specified and directed.

Solid PVC door frame of size 50x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, S&F in opening as per specification & drawing shown in SSR Part-II, complete all as specified and directed.

Aluminium anodised barrel tower bolt of extruded section, 150mm long complete all as specified and directed.

250mm long aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixed clips of sheet cast or extruded section and fixing bolt and sliding bolt of extruded section of cast aluminium alloy, complete all as specified and directed.

150mm long aluminium handle, cast type, anodised complete all as specified and directed.

Steel locking bolts with mild steel electro galvanised plate and bright bolt not less than 10mm dia, 100mm size, complete all as specified and directed.

Mild steel cold rolled butt hinges, medium weight, 100mm long, complete all as specified and directed.

Mild steel framed work such as grills, gratings with ends of bars shouldered or reveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, frame work of water tanks and similar works, conforming to Fe-290, Gde E-165, complete all as specified and directed.

TMT bars 10mm dia and over, cut to length, bent to shape reqd, incl cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia, complete all as specified and directed.

TMT bar 6 to 8mm dia and over, cut to length, bent to shape reqd, incl cranking, bending spirally for hooping for column, hooking end and binding with and including mild steel wire (annealed) not less than 0.9mm dia, complete all as specified and directed.

Steel window side hung glazed and gauged shutters incl projecting type hinges with steel handle and steel peg stay complete with glazing bars dove-tailed or welded complete all as specified and directed.

Steel ventilator with top hung shutter including hinges, steel peg stay, complete with glazing bars dove- tailed or welded, complete all as specified and directed.

Pressed steel frames of size 125x60mm for doors with one or more rebates incl necessary fixing lugs, hinges, lock strike plate, etc and providing one shop coat of primer and tarring back side of frame, complete all as specified and directed.

Pressed steel frames of size 105x60mm for doors with one or more rebates incl necessary fixing lugs, hinges, lock strike plate, etc and providing one shop coat of primer and tarring back side of frame, complete all as specified and directed.

Plain cement concrete, M-15 (Nominal mix), type B-0 (using 12.5mm graded stone aggregates) as in filling of steel chowkats or frames, complete all as specified and as directed.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, complete all as specified and directed.

Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F GI frame work 605x605mm for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre / intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit / tie / purlins etc, at approx 900 mm centre to centre with GI cleat and steel suspenders of appropriate size fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre, including provision of 4 mm thick non-asbestos fibre cement board, ISI marked, fixed to snap grid frame works 605 x 605 mm as in ceiling, flat or sloppy as per manufacture's instructions, complete all as specified and directed.

20mm thick granite (of any type) tiles, bedded and jointed with grey cement slurry and pointed with white cement (1:2) with admixture of pigment to match the shade of granite stone incl grinding and polishing complete over 15mm thick screed bed in CM 1:6, complete all as specified and directed.

50mm thick, PCC M-10 (Nominal Mix), type C-2 (using 40mm graded crushed stone aggregates) as in plinth protection finished even and smooth without using extra cement, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing, removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed.

25mm thick, plain cement concrete, M-15 (Nominal Mix), type B-0 (using 12.5 mm graded crushed stone aggregates) as in floors finished rough surface to receive floor finishes, complete all as specified and directed.

Glazed ceramic coloured tiles 300 x 200 x 7mm thick as in vert surfaces such as skirting dado etc set and jointed in neat cement slurry, pointed in white or coloured cement to match over and incl 10mm thick rendering in CM 1:4 to receive tiles, complete all as specified and directed.

Non skid coloured ceramic tiles 7 to 8 mm thick, area of each tiles exc. 0.11 sqm and but n.exc. 0.18 sqm in floor etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:6, complete all as specified and directed.

Rendering 10mm thick on concrete surfaces as in facia or ceiling in CM 1:3 finished even and fair without using extra cement, complete all as specified and directed.

Rendering 10mm thick in CM 1:6 on fair faces of brick work or concrete surfaces of walls, finished even and fair without using extra cement, complete all as specified and directed.

Rendering 15mm thick on stone masonry or other than fair faces of brick wall in CM 1:4 finished even and fair without using extra cement, complete all as specified and directed.

Taking down cement plaster including tiles of any description on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

Preparation of old treated wall surfaces and applying two coat of oil bound distemper white or tinted, complete all as specified and directed.

Preparation of new plastered or unplastered wall surfaces and applying two coats of oil bound distemper white or tinted, complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of ceiling and applying two coats of white wash, complete all as specified and directed.

Preparing new plastered or unplastered wall surfaces and applying two coats of cement base paint all as specified and directed.

3mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares n.exc. 0.50 sqm in each pane, complete all as specified and directed.

3mm thick figured glass pin head type and glazing with oil putty in squares n.exc. 0.50 sqm in each pane, complete all as specified and directed.

Preparation of new wooden surfaces of any description not otherwise described, exc 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed.

Preparation of new steel surfaces of any description not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified and directed.

Steel tubes 15mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor including cutting chases for concealed work etc, complete all as specified and directed.

Steel tubes 20mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor incl cutting chases for concealed work etc, complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connection, incl cleaning for refixing or removal from site, complete all as specified and directed.

Taking up or down 20mm bore steel tubing and connection, incl cleaning for refixing or removal from site, complete all as specified and directed.

Rotational moulded polyethylene water storage tank 500 ltr capacity, ISI marked (cylindrical vertical with closed top), double wall layer construction, hoisted and fixed in position complete all as specified in SSR Part-I, with necessary GI fittings such as nipple elbow tee tec of appropriate size for making connections incl 20mm bore ball valve brass with polyethylene float and fly nut and dismantling existing water tank of any capacity and removing from site, complete all as specified and directed.

Bib tap, fancy type, chromium plated, cast copper alloy with crutch or butterfly handle, screwed down for high pressure screwed for 15mm bore pipe (fixed in repair), complete all as specified and directed.

15mm bore stop valve, cast copper alloy fancy type chromium plated screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union (fixed in repair), complete all as specified and directed.

PVC connection suitable for 15mm pipe with PTMT nuts and washers for both ends of length 450mm long, (fixed in repair), complete all as specified and directed.

Shower rose, 125mm face dia brass chromium plated, with or without swivel joints, incl shower arm for 15mm, 195mm long with bend of 45 degree with flange of PTMT any colour, fixing to steel pipe or union (fixed in repair), complete all as specified and directed.

Sink with drainage board made of stainless stell 1mm thick kitchen or laboratory with plugs, washers and waste coupling, incl bedding in CM to dwarf wall or providing cantilever brackets, PVC waste pipe and connecting union to pipe overall size 915mm x 460mm bowl size 410 x 330 x 160mm (fixed in repair), complete all as specified and directed.

Vitreous china squatting pan water closet, orissa pattern, size 580 x 440mm, white with integral foot rests incl 'P' or 'S' trap of same material (excl flushing cistern and flush pipe), provn of cement concrete / lime concrete and jointing to flush pipe (fixed in repair), complete all as specified and directed.

10 ltr capacity PVC, low level, valveless, syphonic action type flushing cistern, inlet ball valve, float valve, handle and fixing arrangement, 32mm dia PVC flushing pipe and 15mm dia 450mm long PVC connection with CP brass coupling nuts and PVC washer at both ends (fixed in repair), complete all as specified and directed.

S&F sheet glass shelf assembly consisting of 5.5mm thick glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F Towel Rail 600mm long Of PTMT fixed with and including Chromium plated brass screw and wooden/ plastic cleats ( Min Wt 190 Gms) complete all as specified and directed.

S&F towel ring of PTMT fixed with and including chromium plated brass screw and wooden/ plastic cleats ( Min Wt 105 Gms) complete all as specified and directed.

S&F grating Doom 100mm dia of PTMT complete all as specified and directed.

S&F grating doom 125mm dia with Waste hole of PTMT complete all as specified and directed.

S&F harrison rails, mild steel,chromium plated with fixing brackes, stops, rollers etc.

Dismantling timber scantlings 40sqcm and over in section in any position framed or unframed work etc, complete all as specified.

Vitreous china, wash hand basin, (white) of size 550mmx400mm including cast copper alloy CP Piller Tap Fancy Type , brass CP waste coupling 32mm dia with long screwed shank and fly nuts, PVC medium grade 32mm dia waste pipe, chain and plug, porcelain stopper , PVC connection 15mm dia, 450mm long with brass CP nuts and washers at both ends (fixed in repair), complete all as specified and directed.

S&F roof trusses (framed), trussed, purlins, crane girders, purlins, crane gantries, rails and fastenings and heavy brackets including distance pieces, cleats etc. all as specified.

S&F kitchen plate rack made of stainless steel 0.80mm thick sheet standered size 900 x 900 x 3250mm and designed as approved by GE fixed to wall with wooden/ plastic plug and Screw,( fixed in Repair) complete all as specified as directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc.

Point wiring with 1.5 Sqmm PVC (FRLS) insulated unsheathed multi stranded copper conductor cable 1100 volts grade single core conforming to IS-694-1990 and including one run of continous earth wire to common earth and connected to earth with 1.5 Sqmm PVC (FRLS) insulated unsheathed multi stranded copper conductor cable draw in & incl PVC surface casing 'N' capping double lock type to be fixed with the help of rawal plugs & screws incl necessary fittings & fixture and to be turminated in sunk cast iron/pressed steel/PVC terminal boxes for mounting switches, sockets, regulators etc with 3 mm thick plastic laminated sheet cover of adequate size for one light point/fan point controlled by one switch and making good disturbed surfaces with CM (1:4) to match with the existing surface complete all as specified.

All as per the description of serial item No 76 above but for 5 pin switch socket outlet 5 Amp on same board with other switches, complete all as specified.

All as per the description of serial item No 76 above but for 5 pin switch socket outlet 5 Amp on independent board complete all as specified.

All as per the description of serial item No 76 above but with 2.5 Sqmm PVC (FRLS) insulated copper conductor cable and 2.5 Sqmm PVC (FRLS) insulated copper conductor as earth wire for one 3 Pin 15 Amp socket out let on the independent board.

S&F switch piano flush button, 5 Amps, 240 volts, single pole one way complete all as specified and directed.

Supply and fix socket out let 2 in 1, 3 Pin 5 Amps flush type all as specified and directed.

Supply and fix switch socket combination out let 2 in 1, 5/6 Pin, 5 and 15 Amps flush type all as specified and directed.

S&F lamp holder, insulated body, with back plate for batten fitting with LED Lamp 9 W, complete all as specified.

S&F LED batten T-8, 1x20 W including LED tube Rod 20W complete with provn of flexible cable 3 core, 23/.0076 from ceiling rose to connector complete all as specified and directed.

Taking down old burnt out bulk head fitting any type and installaton LED Bulk Head 10W with pressure plastic housing with clear prismatic diffuser, high efficient LEDs IP54 complete all as specified and directed.

S&F ceiling rose surface type bakelite 50x65 mm two to three terminals all as specified.

Supply and fixing bell push complete all as Specified.

Supply and fixing electronic bell ding dong type complete all as Specified.

Material and labour for sub main wiring with two single core PVC insulated, FRLS unsheathed multi stranded copper conductor cable confirming to IS 694-1990 of size 6 Sqmm (nominal area) and draw in & including PVC surface casing 'N' capping double lock type to be fixed with the help of rawal plugs & screws incl all fittings such as Tee, connector pieces, L-junction etc on joints, not less than 2 mm thick and continuous PVC insulated single core copper conductor multi stranded unsheathed 6 Sqmm as earth wire complete all as specified and as directed. (Two single core cable and one No earth wire shall be measured together as one length) and making good the disturbed surfaces.

Taking down ceiling/exhaust fan any type/size and refixing at same or other location after cleaning, greasing, oiling & servicing complete all as specified and directed.

Supply and fix sheet metal enclosure powder coated DB for fixing of MCBs, SPN 12 ways double door, IP-42 protection with 200 Amp rated bus bar, 240 Volts including taking out of old MCB DB of any type/size and removing from site to MES store for reuse if serviceable or for credit complete all as specified and directed.

Supply and fix sheet metal enclosure powder coated DB for fixing of MCBs, SPN 8 ways double door, IP-42 protection with 200 Amp rated bus bar, 240 Volts including taking out of old MCB DB of any type/size and removing from site to MES store for reuse if serviceable or for credit complete all as specified and directed.

Supply and fix MCB SPN 240 volts, 10kA, 50 Hz of capacity 63 Amps 'C' series all as specified and directed

Supply and fix MCB SPN 240 volts, 10kA, 50 Hz of capacity 40-63 Amps 'C' series all as specified and directed

S&F MCB SP, 240 V, 6-40 Amp 10 KA complete all as specified.

Earthing with galvanized steel earth plate electrode 60cmx60cmx6mm thick, buried directly in ground (earth pit less than 2.25 mtr deep below normal ground level) with top edge of the earth plate not less than 1.5 mtr deep below normal ground level, connected to 4mm dia galvanized iron wire as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel complete with 15mm dia light grade protection pipe, 20mm dia GI light grade watering pipe with funnel including char coal dust, salt, PCC 1:2:4 in pit with precast RCC M-15 cover reinforced with XPM not less then 4.00 Kg per sqm including necessary earth work in any type of soil, removal of surplus soil to a distance not exc 50m, returning filling in complete as shown in electrical plate No 3 of SSR Part-I (2009), and connected to earthing test point all as specified or indicated, including testing on completion. Note: The rates for earthing includes the cost of earth lead and protection pipe upto 7.50m length.

Supply, laying and testing cable XLPE insulated screend PVC bedded, galvanised steel strip or wire armoured electric power cables (Heavy duty) 1100 V grade with stranded aluminium conductor of size 2 core cross sectional area 25 Sqmm, laid in trenches or passing through pipe including taking down of existing cable/service connection of any type or size and removing from site to MES store for reuse if serviceable or for credit all as specified and directed and directed.

Excavation in trenches not exc 1.5m wide and not exc 1.5m deep in any type of soil for laying cables, foundation of poles etc and getting out complete all as specified and directed.

Returning filling in including spreading leveling, watering and well ramming in layers n.exc 25cm thick, complete all as specified and directed.

Removal of excavated material to be distance n.exc 50 mtr and depositing where directed at a level n.exc 1.5m above the starting point, complete all as specified and directed.

Sand cushioning to under ground cable with a layer of sand 8 cm before laying the cable and 15 cm after laying the cable (10cm punned thickness above the top of the upper most cable, total 18 cm), complete all as specified and directed.

Brick common burnt class 'B' covering laid dry, flat transversally along the length of the cable on sand cushioning width equal to the length of the brick complete all as specified.

S&F 40 mm dia bore galvanized iron tubing, light grade including all fittings for cable protection elc laid in floor, trenches or fixed to poles with clamps etc all specified and directed.

M/S THAKUR ENTERPRISES

VIVEKA ENTERPRISES

M/S DOGRA CONSTRUCTION CO

S K MAHAJAN

BHARDWAJ BUILDERS

jatindera enterprises