Providing CAD works for Lift Irrigation Scheme Bahri Dhawali Marhi in Tehsil Dharampur District Mandi HP

Amount

Excavation in foundation, trenches etc. (in pipes and pits) in all kinds of soil such as pick work, jumper work, blasting work in soft / hard rock, chiselling in soft / hard including wedging out of a rock where blasting is prohibited and stacking the excavated earth up to all lifts, stacking the excavated soil up to all lead clear from the edge of excavation and then returniing the stacked soil in 15 centimeters layers when required in to plinths, sides of foundation etc. consolidating each deposited layer by ramming and waterng and then disposing of all surplus excavated earth as per direction and to the entire satisfation of Engineer- in- charge up to leads and lifts.

Laying jointing and commissioning of HDPE (High Density Polyethlene pipe) of following diameter and class confirming to IS 4984-1995 with fusion welding process including all necessary fitting & bend leads and lifts to the entire satisfaction of Engineer-in-charge (earth work in ternches to be mesured and paid separately)

HDPE pipe 75 mm dia PN 12.50 PE- 100 (Labour Rate)

HDPE pipe 75 mm dia PN 4 PE- 80 (Labour Rate)

Fitting and accessories.

63 mm dia PN-4.0, 5.0, 6.0, 8.0 HDPE pipes. (Labour Rate)

63 mm dia PN-6 pipe end

63 mm dia PN-6 HDPE 90° bends with rotating clamp

63 mm dia PN-6 HDPE QC connector

Providing and laying cement conrete 1 : 4 : 8 . ( 1 cement : 4 sand and : 8 grade stone aggregate 40mm nominal size) and curing complete excluding cost of form work in foundation and plinth upto all leads and lifts as per the direction and to the entire satisfaction of Engineer-in-Charge.

Providing and laying cement concrete 1 : 1½ : 3 ( 1 cement : 1½ : sand : 3 graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work and reinfocement for reinforced concrete work in :

Foundation footings bases of columns and the like; and mass concrete as per direction and to the entire satisfaction of Engineer-in-Charge.

Walls any thickness but not less than 0.1m thickness including attached pillaster buttresses, plinth and string courses from top of foundation upto two level all floor level as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm so as to give a fair finish including centring, shuttering strutting and propping etc. with wooden batten and ballies, in all heights of propping and centring below supporting floor to ceiling not exceeding 4 mtrs and removal of the same for insitu-reinforced concrete and plain concrete work in :-

Vertical surfaces such as wall (any thickness) partitions and the like including attached pillasters, buttresses plinth and string courses and the like in all leads and lifts as per direction and to the entire satisfaction of Engineer-in-charge.

Providing laying of Tor steel reinforcement for RCC work including bending binding and placing in position including wire upto all floor level as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing double flanged Cast Iron sluice valve of following dia of Jal Shakti Vibhag approved make conforming to IS: 14846/2000 with up to date amendment as per Class PN-1.00 to withstanding normal seat pressure of 10.20 Kg/cm2 including champion sheet gasket 3mm thick, welding with M.S. flanges table-5 as per IS 6392-1971 including carriage in all leads and lifts as per direction and to the entire satisfaction of Engineer-in-Charge. (Flange table-5 Class PN-1.00)

65 mm dia

Providing and supplying of HDPE pipes of 63 mm dia PN 4 PE-80 as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing double flanged cast steel Sluice valve of following dia of Jal Shakti Vibhag approved make to conforming to BS: 1414/API-600 Class ASA-300 including M.S. flanges as per IS 6392-1971 table-17 including welding of flanges and capable of with standing of 21.00 Kg/cm² seat pressure with upto date amendments including carriage in all leads and lifts as per direction and to the entire satisfaction of Engineer-in-Charge.

300 mm dia

550 mm dia

750 mm dia

Providing and fixing double flanged cast steel Reflux valve of following dia of Jal Shakti Vibhag approved make to conforming to BS: 1868/API-600 Class ASA-300 including M.S. flanges as per IS 6392-1971 including welding of flanges and capable of with standing of 21.00 Kg/cm² seat pressure with upto date amendments including carriage within all leads and lifts as per direction and to the entire satisfaction of Engineer-in-Charge.

300 mm dia

550 mm dia

700 mm dia

750 mm dia

Survey Investigation , design and planning of whole scheme i.e Gravity Main and Distribution system for construction of various civil strucutres proposed under the project area.

HARJEET SINGH

R.G. INDUSTRIES