CONSTRUCTION OF DRY AND WET WASTE PROCESSING PLANT AND C & D WASTE PROCESSING UNIT FOR KARAMSAD ANANAD MUNICIPAL CORPORATION

Sr. No. Particulars Amount Rs.

Name of Work: Development Work For Wet Waste Processing

Schedule-B1 Plant For Karamsad Anand Municipal Corporatrion. ₹

Name of Work : Construction of Dry Waste Processing Plant, AT

Schedule-B2 Lambhavel Site For Anand ,Karamasad & Vallabh Vidhyanagar. ₹

Name of Work : Development of treatment facilities for

Schedule-B3 processing of construction waste & demolition (C&D) waste AT ₹

Karamsad Anand Municipal Corporatrion.

KARAMSAD-ANAND MUNICIPAL CORPORATION, ANAND,Dist:ANAND.

Name of Work: Development Work For Wet Waste Processing Plant For Karamsad Anand

Municipal Corporatrion.

Sr. No. Particulars Amount Rs.

Schedule-B1.1 Compost Pit (5 Unit = 50Pit) ₹

Schedule-B1.2 RCC Road ₹

Schedule-B1.3 Compound wall ₹

Schedule-B1.4 Container Cabin ₹

Schedule-B1.5 CCTV ₹

Schedule-B1.6 100 TPD Wet Waste Processing System (2 × 50 TPD Units) ₹

Name of Work : Construction of Vermi Compost Pit at Decomposite Site, AT Karamsad Anand

Municipal Corporatrion.(5 Unit = 50 Pit)

Abstract of Schedule-B1.1

Description Qty Unit Total Rate Amount

Excavation for foundation upto 1.5 m depth including

sorting out and stacking of useful materials and disposing

off the excavated stuff upto 50 Meter lead. (A) Loose or

Providing and laying cement concrete work 1:2:4 (1-

Cement : 2- Coarse sand : 4- graded stone aggregates

2 mm nominal size) and curing complete excluding cost of 17.00 cu.m 4046.42

formwork and reinforcement for reinforced concrete

work in (A) Foundations (upto 10 ton)

Providing & laying controlled cement concrete M-250

with curing etc. complete incl. the cost of form work but

excluding the cost of reinforcement for R.C.C. work for

Filling available excavated earth (excluding rock) in

trenches ,plinth, sides of foundations etc.in layers not

exceeding 20cm in depth consolidating each deposited

layer by ramming & watering.

Providing TMT Bar FE 500/500D reinforcement for R.C.C.

5 work including bending, binding and placing in position 3000.00 Kg 77.29

complete upto floor two level. (upto 10 ton)

Brick work using common burnt clay building bricks

having crushing strength not less than 35 kg./Sq.Cm. in

foundation and plinth in Cement Mortar 1:6 (1- Cement :

6 -fine sand) Extra for brick work in superstructure

above plinth level upto floor two level (B) Conventional

(i) Half brick masonry in common brunt clay building

bricks having crushing strength not less than

7 Kg/Sq.Cm. in Cement mortar 1:4 (1- Cement : 4 -coarse 14.00 Sqm 629.84

sand ) in foundation and plinth (B) Conventional

Providing 15mm thick cement plaster in single coat on

Rough (Similar)side of single or half brick walls for

interior plastering upto floor two level and finished even

and smooth in (i) Cement mortar 1:3 (1-cement:3-sand)

and finishing with a floating coat of neat cement slurry.

20mm thick sand faced cement plaster on walls upto

height 10 metres above ground level consisting of 12mm

9 thick backing coat of C.M. 1:3 (1-cement : 3-sand) and 59.00 Sqm 352.44

8mm thick finishing coat of C.M. 1:1 (1-cement : 1-sand)

Finishing wall with weather proof exterior emulsion

paint on wall surface (two coats) to give an required

10 shape even shade after thoroughly brushing the surface 149.00 Sqm 120.26

to remove all dirt, and remains of loose powdered

materials.etc complete

Providing and fixing tiles roofing with manglore tiles

including teak reepers of sizes 50mm x 25mm.

Steel work, welded in built up sections framed work

including cutting, hoisting, fixing in position and applying

a priming coat of red lead paint. (A)In beams and joists,

channels angles Tees, flats, with connecting plates or

angle cleats as in main and cross beams. Hip and jack

rafters, purlins conneted to common rafters and the like

Name of Work: Construction of New R.C. C. Road at at SBM Site For Compost Pit Area AT

Karamsad Anand Municipal Corporatrion.

Abstract of Schedule-B1.2

Description Qty Unit Amount

Clearing and grubbing road land including

uprooting rank vegetation grass

bushes,shrubs,sapling and trees girth up to 300 mm

1 0.36 Hectare 80243.79

removal of stumps of trees cut earlier and disposal

of unserviceable materials (A) By manual means in

area of light jungle

Box cutting the Road surface to proper slope and

camber for making a base of road work including

2 removing the excaveted stuff and dipositing on the 2340.00 Cum 104.20

road side slopes directed upto 50 mtrs.lead.

Providing and laying compacted WBM of Grading-II

MCBT metal of size 45 to 63mm in required layers

including using 16% stone screening, 13.2mm size

and 8% stone dust as filler including spreading

watering & consolidation by vibratory roller etc.

Providing and laying cement concrete 1:3:6 (1-

Cement : 3- coarse sand : 6- hand broken stone

4 aggregates 40 mmnominal size) and curing 540.00 Cum 3005.76

complete excluding cost of formwork in (A)

Foundation and Plinth

Providing and laying controlled cement concrete

M.250 and curing complete excluding the cost of

5 formwork and reinforcement for reinforced 720.00 Cum 4345.72

concrete work in (A) Foundations, footings, Base of

columns and Mass concrete

Providing TMT Bar FE 500D reinforcement for

R.C.C. work including bending, binding and placing

in position complete upto floor two level

Labour charges for laying R.C.C. floor of M-200

grade of concrete (Trimix) to be concreted in

alternate panels. The panel shall be formed on four

sides with M.S. channel bolted in position for

forming the size. The entire concrete mass shall be

vibrated with skirt vibrator so as to bring out slurry

on top and smooth finished integrally as per

instruction of Engineer in charge and as per

specification including applying "NITO FLOOR

HARD TOP" or equivalent (Fair create, sikka

applied at the rate of 4.5 kg/10 Sq.m on R.C.C. floor

7 as per Manufacturer's specification) after base 3600.00 Sq.m 90.90

concrete has stiffened to the point when light foot

traffic leaves an imprint of about 3 mm. Any bleed

water should have evaporated including fitting,

joint cutting, filling bitumen curing etc. complete as

per instruction of site Engineer. Excluding steel &

including form work with all tools, plants,

Machinery and all cost of chemical required for

Trimix concrete including Groove Cutting 4 to

mm wide and 60mm Deep at every 4 m Distance.

Name of Work : Construction of Compound wall at Decomposite Site, AT Karamsad Anand Municipal

Abstract of Schedule-B1.3

Description Qty Unit Total Rate Amount

Excavation for foundation upto 1.5 m depth including sorting

out and stacking of useful materials and disposing off the

excavated stuff upto 50 Meter lead. (A) Loose or soft soil

Providing and laying cement concrete work 1:2:4 (1- Cement :

2- Coarse sand : 4- graded stone aggregates 20 mm nominal

2 size) and curing complete excluding cost of formwork and 35.00 cu.m 4046.42

reinforcement for reinforced concrete work in (A)

Foundations (upto 10 ton)

Providing & laying controlled cement concrete M-250 with

curing etc. complete incl. the cost of form work but excluding

the cost of reinforcement for R.C.C. work for Footings.

Providing & laying controlled cement concrete M-250 with

curing etc. complete incl. the cost of form work but excluding

the cost of reinforcement for R.C.C. work for column up to

Providing & laying controlled cement concrete M-250 with

curing etc. complete incl. the cost of form work but excluding

the cost of reinforcement for R.C.C. work for Ground beam &

Plinth beams etc.

Filling available excavated earth (excluding rock) in trenches

,plinth, sides of foundations etc.in layers not exceeding 20cm

in depth consolidating each deposited layer by ramming &

Providing & laying controlled cement concrete M-250 with

curing etc. complete including the cost of form work but

excluding the cost of reinforcement for R.C.C. work at Ground

Floor for Column.

Providing TMT Bar FE 500/500D reinforcement for R.C.C.

13 work including bending, binding and placing in position 22450.00 Kg 77.29

complete upto floor two level. (upto 10 ton)

Brick work using common burnt clay building bricks having

crushing strength not less than 35 kg./Sq.Cm. in foundation

14 and plinth in Cement Mortar 1:6 (1- Cement : 6 -fine sand) 138.00 cu.m 4496.05

Extra for brick work in superstructure above plinth level upto

floor two level (B) Conventional (upto 10 ton)

20 mm. thick sand faced cement plaster on wall upto height

meters above ground level consisting of 12mm thick backing

coat of c.m. 1 : 3 (1 cement : 3 sand) and 8 mm thick finishing

coat of c.m. 1 : 1 (1 cement : 1 sand) etc. complete

Finishing wall with weather proof exterior emulsion paint on

wall surface (two coats) to give an required shape even shade

after thoroughly brushing the surface to remove all dirt, and

remains of loose powdered materials etc. complete

Providing and fixing M.S. grills of required pattern to wooden

frames of windows etc. with M.S. flats at required spacings and

frame alround, square or round bars with round headed bolts

and nuts or by screws (A) Plain Grill. (upto 10 ton)

Painting two coats (excluding priming coat) on new steel and

other metal surface with enamel paint, brushing, interior to

25 give an even shade including cleaning the surface an even 21.00 Sqm 92.20

shade including cleanicn the surface of all dirt, dust and other

foreign matter.

Providing and fixing 1.20 Metre high fencing with 2.0 Metre

long M.S. Angle posts 40mm x 40 mm x6 mm and oil painting

3 coats fixed at 2.5 Mt,C/c. with five Horizontan lines and two

diagonals of galvanised steel barbed wire weighting 9.38 Kg.

per 100 Metre, strained and fixed to posts with G.I,staples

including fixing the

postsin ground with 0.5 M x 0.5.M x 0.5 M. block in C.C1:5:10

Name of Work: Providing, Supplying & Fixing of Container Cabin at at SBM Site For Compost Pit

Area AT Karamsad Anand Municipal Corporatrion.

Abstract of Schedule-B1.4

Description Qty Unit Amount

Providing, supplying, fabricating, transporting, and

fixing in position prefabricated container cabin

made from modified ISO shipping container / MS

steel structure, suitable for use as site office,

accommodation, storage, or security cabin,

complete in all respects as per specifications and

direction of Engineer-in-Charge.

Name of Work: Providing, Supplying & Fixing of CCTV at at SBM Site For Compost Pit Area AT

Karamsad Anand Municipal Corporatrion.

Abstract of Schedule-B1.5

Description Qty Unit Amount

Supply Installation Testing & Commissioning of 2MP

IR Dome Camera(2.8mm Lens with Aperture of F1.6

(By Default)/F2.0(On demand)),Audio Support,

1/2.8” SONY - CMOS, 2MP, 0Lux with IR LED on,

2.8mm IR Distance up to 50m, Video Analytics: Trip

Wire, Intrusion Detection and Motion Detection,

H.265/H.264/M-JPEG Video Compression, PoE

1 Support, NAS Storage, SD Card(512GB), Quad Stream 15.00 Ea 11378.66

Support, 1/1 Audio I/O, 1/1 Alarm I/O, True WDR, 3D

Noise Reduction, Adaptive Streaming, Smart

Streaming and ROI, SNR > 70 dB, ER Compliant &

Cyber Secured as per ISO / IEC 27402, BIS, CE, FCC,

RoHS, IK10, IP67, UL, NEMA 4X, NDAA Compliant &

STQC Certified.

Supply Installation Testing & Commissioning of 2MP

IR Bullet Camera(6.0mm Lens with Aperture of

F1.6(By Default) /F2.0 (On demand)),Audio Support,

1/2.8” SONY - CMOS, 2MP, 0Lux with IR LED on,

6.0mm, IR Distance up to 50m, Video Analytics: Trip

Wire, Intrusion Detection and Motion Detection,

H.265/H.264/M-JPEG Video Compression, PoE

Support, NAS Storage, SD Card(512GB), Quad Stream

Support, 1/1 Audio I/O, 1/1 Alarm I/O, True WDR, 3D

Noise Reduction, Adaptive treaming, Smart Streaming

and ROI, SNR > 70 dB, , BIS, CE, FCC, RoHS, IK10, IP67,

UL, NEMA 4X, NDAA Compliant & STQC Certified.

Supply Installation Testing & Commissioning of

Channel NVR with 4K Support and 8 HDD Slots, 64 IP

Channel Inputs; 4K HDMI, 1/1 Audio I/O and 2/1

Alarm I/O, 12MP, 8MP, 5MP, 4MP, 3MP, 2MP, 720p,

D1 and CIF Recording Resolution, 4x 4K/ 10x

3MP/16x 1080p Local Decoding, 8 SATA HDD

Support (Maximum 18TB Capacity per Slot, Hard Disk

Not Included), Save Storage Space with Adaptive

Recording and Camera-wise Recording Retention,

SMS & Email Notification, Video Pop-up, Alarms and

Instant Calling from Mobile Application, Throughput -

512Mbps Uplink, 512Mbps Downlink, ONVIF and

support for other camera brands.

SITC of 24 x 10/100/1000BASE-T PoE ports 4 x

Gigabit RJ45/SFP Combo ports Advanced L2

switching and security features L2+ Static Routing

Optional “standard mode” or “surveillance mode”

management user interface 193 W PoE budget

SITC of Patch Panel Cat 6 UTP Keystone Type-

Port-Fully Loaded

Supply, Installation, Testing and Commissioning of

10TB HDD Enterprise / Surveillance Harddisk

Supply, Installation, Testing and Commissioning of

43" 4K LED Display

Supply, Installation, Testing and Commissioning of 9U

8 Indoor Rack with required accessories like fan, 6 2.00 Ea 9374.82

socket 5/15amp PDU, hardware packet

Name of Work : Providing & fixing machinery For Wet Waste Processing Plant For Karamsad Anand

Municipal Corporatrion.

100 TPD Wet Waste Processing System (2 × 50 TPD Units)

Abstract of Schedule-B1.5

Description Amount

1 Material Intake System

• Loading Hopper with Conveyor (2 Nos)

• Width: 4000 mm | Length: 1000 mm

• Frame: Heavy-duty MS

• Drive: 3 HP Moto

Sorting Conveyor (2 Nos)

• Width: 8000 mm

• Application: Manual segregation

2 Size Reduction Module

Feeding Conveyor (2 Nos)

• Width: 10000 mm

• Pulley: 220 mm Dia

Twin Shaft Shredder – 80 HP

• Throughput: 2–2.5 TPH

• Blade: Imported alloy steel

• Shaft Dia: 90–100 mm

• Gearbox: Heavy-duty planetary

• Auto Reverse Function

• Suitable for mixed solid waste

3 Liquid Separation Module

Dewatering Screw Press

• Capacity: 1 TPH

• Material: SS-304 Contact Parts

• Speed: Variable

• Output: Reduced moisture organic mass

4 Homogenization System

• Capacity: 5 TPH

• Shaft: Heavy-duty 75 mm

5 Composting Infrastructure

Curing Conveyor (3 Nos) – 3 HP

• Engine Power: 20 HP

• Rotor: 2.4 Meter

• Function: Aeration & mixing

6 Screening & Refining

• Dia: 1.5 Meter

• Length: 6 Meter

• Hole Size: 6 mm

• Feeding / Process / Rejection

• Motors: 2 HP each

• Bearings: Branded

7 Utility Equipment

• Sieving Machine

• Industrial Weigh Scale (500 Kg)

• Wheel Barrows (MS)

• Bag Packaging Machine

• Waste Bins (220 L HDPE)

KARAMSAD-ANAND MUNICIPAL CORPORATION, ANAND,Dist:ANAND.

Name of Work : Construction of Dry Waste Processing Plant, AT Lambhavel Site For Anand

,Karamasad & Vallabh Vidhyanagar.

Sr. No. Particulars Amount Rs.

Schedule-B2.1 Material Recovery Facility Shed ₹

Schedule-B2.2 Security Cabin ₹

Schedule-B2.3 Vermi Compost Shed ₹

Schedule-B2.4 Weighbridge cabin & Weighbridge ₹

Schedule-B2.5 Ladies & Gents Toilet Block ₹

Schedule-B2.6 Rest Room ₹

Schedule-B2.7 Office & Conference ₹

Schedule-B2.8 Changing Room ₹

Schedule-B2.9 MRF Shed Electrification ₹

Schedule-B2.10 Streetlight Pole ₹

Schedule-B2.11 Dry Waste Processing Plant – 100 TPD ₹

Name of Work : Construction of Material Recovery Facility Shed and Platform at Decomposite Site, AT

Karamasad Anand Municipal Corporatrion.

Abstract of Schedule-B2.1

Description Qty Unit Amount

Excavation for foundation upto 1.5 m depth including

sorting out and stacking of useful materials and disposing off

the excavated stuff upto 50 Meter lead. (A) Loose or soft soil

Excavation for foundation for depth from 1.5 m to 3.0 m

including sorting out and stacking of useful materials and

disposing off the excavated stuff upto 50 Meter lead.(A)

Loose or soft soil

Providing and laying compacted WBM of Grading-II MCBT

metal of size 45 to 63mm in required layers including using

3 16% stone screening, 13.2mm size and 8% stone dust as 693.00 Cum 2039.19

filler including spreading watering & consolidation by

vibratory roller etc. comp.

Providing and laying cement concrete work 1:2:4 (1-

Cement : 2- Coarse sand : 4- graded stone aggregates 20 mm

4 nominal size) and curing complete excluding cost of 566.00 cu.m 4046.42

formwork and reinforcement for reinforced concrete work

in (A) Foundations (upto 10 ton)

Providing & laying controlled cement concrete M-250 with

curing etc. complete incl. the cost of form work but

excluding the cost of reinforcement for R.C.C. work for

Providing & laying controlled cement concrete M-250 with

curing etc. complete incl. the cost of form work but

excluding the cost of reinforcement for R.C.C. work for

column up to plinth.

Providing & laying controlled cement concrete M-250 with

curing etc. complete incl. the cost of form work but

excluding the cost of reinforcement for R.C.C. work for

Ground beam & Plinth beams etc.

Providing & laying controlled cement concrete M-250 with

curing etc. complete including the cost of form work but

excluding the cost of reinforcement for R.C.C. work at

Ground Floor for Column.

Providing & laying controlled cement concrete M-250 with

curing etc. complete including the cost of form work but

excluding the cost of reinforcement for R.C.C. work at First

Floor for Column.

Providing & laying controlled cement concrete M-250 with

curing etc. complete including the cost of form work but

excluding the cost of reinforcement for R.C.C. work at

Ground Floor for Beam.

Providing & laying controlled cement concrete M-250 with

curing etc. complete including the cost of form work but

excluding the cost of reinforcement for R.C.C. work at First

Floor for Beam.

Filling available excavated earth (excluding rock) in trenches

,plinth, sides of foundations etc.in layers not exceeding 20cm

in depth consolidating each deposited layer by ramming &

Filling in foundation and plinth with murrum or selected soil

12 in layers of 20cm. thickness including watering, ramming 1733.00 cu.m 294.38

and consolidating etc. complete.

Providing TMT Bar FE 500/500D reinforcement for R.C.C.

13 work including bending, binding and placing in position 92700.00 Kg 77.29

complete upto floor two level. (upto 10 ton)

Brick work using common burnt clay building bricks having

crushing strength not less than 35 kg./Sq.Cm. in foundation

and plinth in Cement Mortar 1:6 (1- Cement : 6 -fine sand)

Extra for brick work in superstructure above plinth level

upto floor two level (B) Conventional (upto 10 ton)

Providing 15mm thick cement plaster in single coat on

Rough (Similar)side of single or half brick walls for interior

plastering upto floor two level and finished even and smooth

in (i) Cement mortar 1:3 (1-cement:3-sand) and finishing

with a floating coat of neat cement slurry. (upto 10 ton)

Finishing wall with weather proof exterior emulsion paint

on wall surface (two coats) to give an required shape even

16 shade after thoroughly brushing the surface to remove all 2172.00 Sq.m 120.26

dirt, and remains of loose powdered materials.etc complete

Providing corrugated G.I. sheet of class-3 roofing fixed with

glavanished iron J or L Hooks, Bolts and nuts 8mm diameter

with bitumen and G.I. limpet washer or G.I. limpet washer.

filled with white lead complete excluding the cost of purlins,

Rafters and Trusses.(1) 0.80 mm thick sheet.

Steel work, welded in built up sections framed work

including cutting, hoisting, fixing in position and applying a

priming coat of red lead paint. (A)In beams and joists,

18 channels angles Tees, flats, with connecting plates or angle 240.75 Q. 9108.48

cleats as in main and cross beams. Hip and jack rafters,

purlins conneted to common rafters and the like

Structure Less PROFLEX or equivalent Roofing systems with

proper overlapping and seaming b/w different sheets

without making holes or preventing the overturning the roof

by wind addition made up from superior quality, structural

grade steel. Base metal width 912 mm, Steel Grade : Grade D

and Thickness 1.50 mm BMT, 1.55 mm APT with tolerance

of +/- 0.02 mm, Regular Modified Polyster Imported

Galvalume Steel having Profiled width of 912 mm +/-4mm.

Design, supply, & fabrication of self supported single span

arch roof fabricated from mechanically seamed

manufactured by American Hydraulic Machines to profiles of

Imported Galvalume Cold Rolled Structural Steel coils as per

standard ASTM A792, Steel Sheet, Aluminum-Zinc Alloy

Coated by Hot-Dip Process.The work should be carried out

by specilialize and nationally approved (clear Track Record)

Agency only. Providing and fixing of hangers/clamps as per

manufacturers specifications for laying of cables and

hanging of bulbs from Self Supported Proflex Systems

Technical specifications for galvalume steel sheets:·Steel

grade: D·Standard: Colour coated galvalume steel sheets

complying to ASTM A792· Coil width: 912mm, tolerance ±

4.00mm Profiled width : 625mm, tolerance ±

10.00mm·Base metal thickness (BMT): 0.80 mm,1.00

mm,1.20 mm (tolerance as ± 0.04mm) · Total coated

thickness (TCT): 0.85 mm,1.05 mm,1.25mm (tolerance as ±

0.04mm)· Alloy coating: AZ150 (150 gram/Sqm) minimum

(Aluminium 55%, Zinc 43.5%, Silicon 1.5%)· Yield strength:

350 MPa· Paint coating: Regular modified polyester· Top

coat of painting: 25 micron minimum (colour 20 micron and

primer 5 micron)· Bottom coat of painting: 12 micron

minimum (colour 7 micron and primer 5 micron).

Name of Work : Construction of Security Cabin at Decomposite Site, AT Karamsad Anand Municipal

Abstract of Schedule-B2.2

Description Qty Unit Amount

Excavation for foundation upto 1.5 m depth including sorting

out and stacking of useful materials and disposing off the

excavated stuff upto 50 Meter lead. (A) Loose or soft soil

Providing and laying cement concrete work 1:2:4 (1- Cement : 2-

Coarse sand : 4- graded stone aggregates 20 mm nominal size)

2 and curing complete excluding cost of formwork and 6.00 cu.m 4046.42

reinforcement for reinforced concrete work in (A) Foundations

Providing & laying controlled cement concrete M-250 with

curing etc. complete incl. the cost of form work but excluding the

cost of reinforcement for R.C.C. work for Footings.

Providing & laying controlled cement concrete M-250 with

curing etc. complete incl. the cost of form work but excluding the

cost of reinforcement for R.C.C. work for column up to plinth.

Providing & laying controlled cement concrete M-250 with

curing etc. complete incl. the cost of form work but excluding the

cost of reinforcement for R.C.C. work for Ground beam & Plinth

Providing & laying controlled cement concrete M-250 with

curing etc. complete including the cost of form work but

excluding the cost of reinforcement for R.C.C. work in

foundation and plinth for Copping & Beam etc.

Filling available excavated earth (excluding rock) in trenches

,plinth, sides of foundations etc.in layers not exceeding 20cm in

depth consolidating each deposited layer by ramming &

Filling in foundation and plinth with murrum or selected soil in

8 layers of 20cm thickness including watering rammingand 10.00 Cu.m. 294.38

consolidating etc. complete

Carring out plinth treatment to post construction existing

structure by spraying chemical solution for termite control

treatment including labour and material consistment with I.S.I

specification. Using ehlordene and ehiorpurfiles 20 EC. As Per

9 6131_paret-ll eonsentration Weight one percent is 16.00 Sqm 124.35

recommended i.e one litre 20 Ee chemical emulsion with 19 liter

give 1 % concrentration inclusive of one litre chemical emulsion

appication at the rate of 5 Litre chemical I Sqm of surface is

recommended as per I.S

Providing & laying controlled cement concrete M-250 with

curing etc. complete including the cost of form work but

excluding the cost of reinforcement for R.C.C. work at Ground

Floor for Column.

Providing & laying controlled cement concrete M-250 with

curing etc. complete including the cost of form work but

excluding the cost of reinforcement for R.C.C. work at Ground

Providing and Laying controlled Cement Concrete M-250 and

curing etc. Complete including the cost of form work but

excluding the cost of reinforcement for R.C.C. work at Ground

Floor for Slabs & Shelves etc.

Providing & laying controlled cement concrete M-250 with

curing etc. complete including the cost of form work but

excluding the cost of reinforcement for R.C.C. work at Ground

Floor for Lintel

Providing and laying cement concrete M.200 for Providing &

laying controlled cement concrete M-250 with curing etc.

14 complete including the cost of form work but excluding the cost 1.10 cu.m 6445.06

of reinforcement for R.C.C. work at Ground Floor for Chajja.

Providing TMT Bar FE 500/500D reinforcement for R.C.C. work

15 including bending, binding and placing in position complete 2533.00 Kg 77.29

upto floor two level. (upto 10 ton)

Brick work using common burnt clay building bricks having

crushing strength not less than 35 kg./Sq.Cm. in foundation and

plinth in Cement Mortar 1:6 (1- Cement : 6 -fine sand) Extra for

brick work in superstructure above plinth level upto floor two

level (B) Conventional (upto 10 ton)

Providing 15mm thick cement plaster in single coat on Rough

(Similar)side of single or half brick walls for interior plastering

upto floor two level and finished even and smooth in (i) Cement

mortar 1:3 (1-cement:3-sand) and finishing with a floating coat

of neat cement slurry. (upto 10 ton)

Providing 15mm thick cement plaster in single coat on

brick/concrete walls for interior plastering upto floor two level

and finished even and smooth in (i) Cement mortar 1:3 (1-

cement:3-sand) plastering on ceilings and soffits of stairs upto

floor two level instead of plastering on walls. finishing with a

floating coat of neat cement slurry.

20 mm. thick sand faced cement plaster on wall upto height

meters above ground level consisting of 12mm thick backing

16 coat of c.m. 1 : 3 (1 cement : 3 sand) and 8 mm thick finishing 64.00 Sqm 352.44

coat of c.m. 1 : 1 (1 cement : 1 sand) etc. complete

Finishing wall with weather proof exterior emulsion paint on

wall surface (two coats) to give an required shape even shade

after thoroughly brushing the surface to remove all dirt, and

remains of loose powdered materials etc. complete

Applying two coats of Birla(white cement based) or Asian

(acrylic lapy putty) or equivalent & two coats of primer of

approved brand and manufacture on new wall surface to give an

even shade including thoroughly brushing the surface free from

mortar dropping and other foreign matter and sand papered

Wall painting (two coats) with plastic emulsion paint of

approved brand and manufacture on undecorated wall surface

19 to give an even shade including throughly brushing the surface 58.00 Sqm 82.85

free from mortar droppings and other foreign matter and sand

papered smooth.

Providing and fixing 35 mm thick shutters for Doors, windows

and clerestory windows including Indian teak wood frames

cm x 7 cm. size including anodized alluminium fixtures and

fastenings including primer coat of approved quality and two

coats of oil painting etc, complete. (ii) Fully Panelled.

Providing and laying polished kota stone slab flooring over

mm (average) thick base of cement mortar 1 : 6 (1 cement :

21 course sand) laid over and jointed with grey cement slurry 16.00 Sqm 1019.39

including rubbing and polishing etc. complete (A) 25 mm thick

Providing and laying polished kota stone slab 25mm thick in

risers of steps,skirting Dedo and pillars laid on 10mm thick

cement mortar 1:3 (1-Cement : 3 coarse sand) and jointed with

gray cement slury mixed with pigment to match the shade of

slab including rubbing and polishing etc. complete. (upto 10 ton)

Providing and fixing window having extruded aluminium Colour

anodized section frame main outer size 63.50 x 38.10 x

mm(of Jindal Section no:4605,@ Wt 1.094 Kg / Rmt), horizontal

two track member size 61.85 mm x 31.75 mm x 1.20mm (of

Jindal Section no: 8687 @ wt.of 0.695 Kg/mt), vertical member

of size 61.85 mm x 31.75mm x 1.30 mm (of Jindal Section

no:8758 @ wt.of 0.0.659 Kg/mt) with sliding shutters of

horizontal member size 40mm x 18mm x 1.29mm (of Jindal

Section no:8949 @ wt.of 0.456Kg/mt), vertical member of size

40mm x 18mm x 1.29mm (of Jindal Section no:8947 @ wt.of

0.456Kg/mt/ Section 8948, @ Wt. 0.457 Kg/mt) with 5 mm

thick transparent bronze colour tinted float glass with powder

coated aluminium fittings and fixtures and transparent silicon

sealant glass fixing to frame as per details etc. complete for

Providing and fixing M.S. grills of required pattern to wooden

frames of windows etc. with M.S. flats at required spacings and

24 frame alround, square or round bars with round headed bolts 408.00 Kg 106.23

and nuts or by screws (A) Plain Grill. (upto 10 ton)

Painting two coats (excluding priming coat) on new steel and

other metal surface with enamel paint, brushing, interior to give

25 an even shade including cleaning the surface an even shade 5.00 Sqm 92.20

including cleanicn the surface of all dirt, dust and other foreign

Providing and laying broken chine mosaic flooring for terrace

using 12 mm to 20 mm broken pieces of glazed tiles to be laid

over cement mortar 1:3 to plain or slope and to be tempered to

26 bring mortar cream out upto surface using white cement 39.00 Sqm 779.70

including rounding off junctions and extending them upto 15 cm

along the wall, clearing with water and oxalic acid etc. as

Point wiring for Light / Fan/ Bell/ Primary Point with 2-1.5 sq.

mm & earth wire of 1.5 sq. mm (green) both are of ISI marked

1.1 kv grade FRLS PVC insulated multi strand copper wires

upto max length of 10 mt, in below type of pipe erected with 6A

Tissino Type ISI marked flush type switch / bell push and

accessories erected on Metal / PVC/Wooden Box covered with

3 mm thick PC(Polycarbonate) /Acrylic/Laminated sheet. with

necessary Lamp holder/ceiling rose / H.D.Connector as directed.

(b) with 16 swg(1.6 mm thick) HGS metal conduit pipe and

accessories painted black erected flushed on wall/ceiling

Providing & erecting 240 V MCB double pole switch for motor &

inductive load (C Curve) having 10 KA breaking capacity &

confirms to IS : 8828 in existing box having following capacity

(B) 40 Amp Cat-III.

Providing and erecting Approved make Ceiling fan with double

ball bearing ISI mark with condenser A.C. 23OV.50 c/s.1200

29 mm. sweep complete, canopy erected on existing hook or clamp 2.00 Each 1596.81

with earthing. [Make shall be approved by Engineer in charge]

Name of Work : Construction of Vermi Compost at Decomposite Site, AT Karamsad Anand

Municipal Corporatrion.

Abstract of Schedule-B2.3

Description Qty Unit Total Rate Amount

Excavation for foundation upto 1.5 m depth including

sorting out and stacking of useful materials and disposing

off the excavated stuff upto 50 Meter lead. (A) Loose or soft

Providing and laying cement concrete work 1:2:4 (1-

Cement : 2- Coarse sand : 4- graded stone aggregates 20 mm

2 nominal size) and curing complete excluding cost of 17.00 cu.m 4046.42

formwork and reinforcement for reinforced concrete work

in (A) Foundations (upto 10 ton)

Providing & laying controlled cement concrete M-250 with

curing etc. complete incl. the cost of form work but

excluding the cost of reinforcement for R.C.C. work for

Filling available excavated earth (excluding rock) in

trenches ,plinth, sides of foundations etc.in layers not

exceeding 20cm in depth consolidating each deposited layer

by ramming & watering.

Providing TMT Bar FE 500/500D reinforcement for R.C.C.

5 work including bending, binding and placing in position 3000.00 Kg 77.29

complete upto floor two level. (upto 10 ton)

Brick work using common burnt clay building bricks having

crushing strength not less than 35 kg./Sq.Cm. in foundation

6 and plinth in Cement Mortar 1:6 (1- Cement : 6 -fine sand) 55.00 cu.m 4496.05

Extra for brick work in superstructure above plinth level

upto floor two level (B) Conventional (upto 10 ton)

(i) Half brick masonry in common brunt clay building bricks

having crushing strength not less than 35 Kg/Sq.Cm. in

Cement mortar 1:4 (1- Cement : 4 -coarse sand ) in

foundation and plinth (B) Conventional

Providing 15mm thick cement plaster in single coat on

Rough (Similar)side of single or half brick walls for interior

plastering upto floor two level and finished even and

smooth in (i) Cement mortar 1:3 (1-cement:3-sand) and

finishing with a floating coat of neat cement slurry. (upto

20mm thick sand faced cement plaster on walls upto height

10 metres above ground level consisting of 12mm thick

backing coat of C.M. 1:3 (1-cement : 3-sand) and 8mm thick

finishing coat of C.M. 1:1 (1-cement : 1-sand) etc. complete.

Finishing wall with weather proof exterior emulsion paint

on wall surface (two coats) to give an required shape even

shade after thoroughly brushing the surface to remove all

dirt, and remains of loose powdered materials.etc complete

Providing and fixing tiles roofing with manglore tiles

including teak reepers of sizes 50mm x 25mm.

Steel work, welded in built up sections framed work

including cutting, hoisting, fixing in position and applying a

priming coat of red lead paint. (A)In beams and joists,

channels angles Tees, flats, with connecting plates or angle

cleats as in main and cross beams. Hip and jack rafters,

purlins conneted to common rafters and the like

Name of Work : Construction of Weighbridge Cabin & Weighbridge at Decomposite Site, AT Karamsad

Anand Municipal Corporatrion.

Abstract of Schedule-B2.4

Description Qty Unit Total Rate Amount

Excavation for foundation upto 1.5 m depth including

sorting out and stacking of useful materials and disposing off

the excavated stuff upto 50 Meter lead. (A) Loose or soft soil

Excavation for foundation for depth from 1.5 m to 3.0 m

including sorting out and stacking of useful materials and

disposing off the excavated stuff upto 50 Meter lead.(A)

Loose or soft soil

Poroviding and laying rubble for appron (each stone

3 weighting not less than 40Kg.) including and packing and 66.00 cu.m 1083.81

filing below the foundation.

Providing and laying cement concrete work 1:2:4 (1- Cement

: 2- Coarse sand : 4- graded stone aggregates 20 mm nominal

4 size) and curing complete excluding cost of formwork and 24.00 cu.m 4046.42

reinforcement for reinforced concrete work in (A)

Foundations (upto 10 ton)

Providing & laying controlled cement concrete M-250 with

curing etc. complete incl. the cost of form work but excluding

the cost of reinforcement for R.C.C. work for Footings.

Providing & laying controlled cement concrete M-250 with

curing etc. complete incl. the cost of form work but excluding

the cost of reinforcement for R.C.C. work for column up to

Providing & laying controlled cement concrete M-250 with

curing etc. complete incl. the cost of form work but excluding

the cost of reinforcement for R.C.C. work for Ground beam

& Plinth beams etc.

Filling available excavated earth (excluding rock) in trenches

,plinth, sides of foundations etc.in layers not exceeding 20cm

in depth consolidating each deposited layer by ramming &

Filling in foundation and plinth with murrum or selected soil

9 in layers of 20cm. thickness including watering, ramming 7.00 cu.m 294.38

and consolidating etc. complete.

Carring out plinth treatment to post construction existing

structure by spraying chemical solution for termite control

treatment including labour and material consistment with

I.S.I specification. Using ehlordene and ehiorpurfiles 20 EC.

As Per 6131_paret-ll eonsentration Weight one percent is

recommended i.e one litre 20 Ee chemical emulsion with

liter give 1 % concrentration inclusive of one litre chemical

emulsion appication at the rate of 5 Litre chemical I Sqm of

surface is recommended as per I.S

Providing & laying controlled cement concrete M-250 with

curing etc. complete including the cost of form work but

11 excluding the cost of reinforcement for R.C.C. work at 2.00 cu.m 7177.12

Ground Floor for Column.

Providing & laying controlled cement concrete M-250 with

curing etc. complete including the cost of form work but

excluding the cost of reinforcement for R.C.C. work at

Ground Floor for Beam

Providing and Laying controlled Cement Concrete M-250

and curing etc. Complete including the cost of form work but

excluding the cost of reinforcement for R.C.C. work at

Ground Floor for Slabs & Shelves etc.

Providing & laying controlled cement concrete M-250 with

curing etc. complete including the cost of form work but

14 excluding the cost of reinforcement for R.C.C. work at 0.40 cu.m 6445.06

Ground Floor for Lintal

Providing & laying controlled cement concrete M-250 with

curing etc. complete including the cost of form work but

excluding the cost of reinforcement for R.C.C. work at

Ground Floor for Chhajja

Providing TMT Bar FE 500/500D reinforcement for R.C.C.

16 work including bending, binding and placing in position 17160.00 Kg 77.29

complete upto floor two level. (upto 10 ton)

Brick work using common burnt clay building bricks having

crushing strength not less than 35 kg./Sq.Cm. in foundation

and plinth in Cement Mortar 1:6 (1- Cement : 6 -fine sand)

Extra for brick work in superstructure above plinth level

upto floor two level (B) Conventional (upto 10 ton)

Providing 15mm thick cement plaster in single coat on

Rough (Similar)side of single or half brick walls for interior

plastering upto floor two level and finished even and smooth

in (i) Cement mortar 1:3 (1-cement:3-sand) and finishing

with a floating coat of neat cement slurry. (upto 10 ton)

Providing 15mm thick cement plaster in single coat on

brick/concrete walls for interior plastering upto floor two

level and finished even and smooth in (i) Cement mortar 1:3

19 (1-cement:3-sand) plastering on ceilings and soffits of stairs 13.00 Sqm 280.46

upto floor two level instead of plastering on walls. finishing

with a floating coat of neat cement slurry.

20 mm. thick sand faced cement plaster on wall upto height

10 meters above ground level consisting of 12mm thick

20 backing coat of c.m. 1 : 3 (1 cement : 3 sand) and 8 mm thick 47.00 Sqm 352.44

finishing coat of c.m. 1 : 1 (1 cement : 1 sand) etc. complete

Finishing wall with weather proof exterior emulsion paint

on wall surface (two coats) to give an required shape even

21 shade after thoroughly brushing the surface to remove all 47.00 Sqm 120.26

dirt, and remains of loose powdered materials etc. complete

Applying two coats of Birla(white cement based) or Asian

(acrylic lapy putty) or equivalent & two coats of primer of

approved brand and manufacture on new wall surface to

give an even shade including thoroughly brushing the

surface free from mortar dropping and other foreign matter

and sand papered smooth.

Wall painting (two coats) with plastic emulsion paint of

approved brand and manufacture on undecorated wall

23 surface to give an even shade including throughly brushing 48.00 Sqm 82.85

the surface free from mortar droppings and other foreign

matter and sand papered smooth.

Providing and fixing 35 mm thick shutters for Doors,

windows and clerestory windows including Indian teak

wood frames 10 cm x 7 cm. size including anodized

alluminium fixtures and fastenings including primer coat of

approved quality and two coats of oil painting etc, complete.

(ii) Fully Panelled.

Providing and laying polished kota stone slab flooring over

20 mm (average) thick base of cement mortar 1 : 6 (1

25 cement : 6 course sand) laid over and jointed with grey 13.00 Sqm 1019.39

cement slurry including rubbing and polishing etc. complete

(A) 25 mm thick (upto 10 ton)

Providing and laying polished kota stone slab 25mm thick in

risers of steps,skirting Dedo and pillars laid on 10mm thick

cement mortar 1:3 (1-Cement : 3 coarse sand) and jointed

with gray cement slury mixed with pigment to match the

shade of slab including rubbing and polishing etc. complete.

Providing and fixing window having extruded aluminium

Colour anodized section frame main outer size 63.50 x

x 1.95 mm(of Jindal Section no:4605,@ Wt 1.094 Kg / Rmt),

horizontal two track member size 61.85 mm x 31.75 mm x

1.20mm (of Jindal Section no: 8687 @ wt.of 0.695 Kg/mt),

vertical member of size 61.85 mm x 31.75mm x 1.30 mm (of

Jindal Section no:8758 @ wt.of 0.0.659 Kg/mt) with sliding

shutters of horizontal member size 40mm x 18mm x

27 1.29mm (of Jindal Section no:8949 @ wt.of 0.456Kg/mt), 5.00 Sqm 1713.70

vertical member of size 40mm x 18mm x 1.29mm (of Jindal

Section no:8947 @ wt.of 0.456Kg/mt/ Section 8948, @ Wt.

0.457 Kg/mt) with 5 mm thick transparent bronze colour

tinted float glass with powder coated aluminium fittings and

fixtures and transparent silicon sealant glass fixing to frame

as per details etc. complete for window.

Providing and fixing M.S. grills of required pattern to

wooden frames of windows etc. with M.S. flats at required

28 spacings and frame alround, square or round bars with 315.00 Kg 106.23

round headed bolts and nuts or by screws (A) Plain Grill.

Painting two coats (excluding priming coat) on new steel

and other metal surface with enamel paint, brushing, interior

29 to give an even shade including cleaning the surface an even 5.00 Sqm 92.20

shade including cleanicn the surface of all dirt, dust and

other foreign matter.

Providing and laying broken chine mosaic flooring for

terrace using 12 mm to 20 mm broken pieces of glazed tiles

to be laid over cement mortar 1:3 to plain or slope and to be

30 tempered to bring mortar cream out upto surface using 16.00 Sqm 779.70

white cement including rounding off junctions and extending

them upto 15 cm along the wall, clearing with water and

oxalic acid etc. as directed.

Supply, installation, testing and commissioning of Electronic

Weighbridge of size 7.50 m × 3.00 m and maximum capacity

50 MT, pit/pitless type fabricated steel platform with anti-

skid chequered top plate, high accuracy compression type

load cells (IP68/IP69K), digital weight indicator with

display, junction box, interconnecting armoured cables and

earthing system, including installation, calibration, statutory

31 stamping and complete commissioning excluding all civil 1.00 No 806979.90

works/foundation, as per manufacturer specifications and

direction of Engineer-in-Charge.

Warranty: Minimum 1 year warranty for complete

weighbridge system including load cells, indicator and

accessories. Note:

Point wiring for Light / Fan/ Bell/ Primary Point with 2-1.5

sq. mm & earth wire of 1.5 sq. mm (green) both are of ISI

marked 1.1 kv grade FRLS PVC insulated multi strand

copper wires upto max length of 10 mt, in below type of pipe

erected with 6A Tissino Type ISI marked flush type switch /

bell push and accessories erected on Metal / PVC/Wooden

32 Box covered with 3 mm thick PC(Polycarbonate) 10.00 No 590.85

/Acrylic/Laminated sheet. with necessary Lamp

holder/ceiling rose / H.D.Connector as directed. (b) with

swg(1.6 mm thick) HGS metal conduit pipe and accessories

painted black erected flushed on wall/ceiling complete

Providing & erecting 240 V MCB double pole switch for

motor & inductive load (C Curve) having 10 KA breaking

capacity & confirms to IS : 8828 in existing box having

following capacity (B) 40 Amp Cat-III.

Providing and erecting Approved make Ceiling fan with

double ball bearing ISI mark with condenser A.C. 23OV.50

34 c/s.1200 mm. sweep complete, canopy erected on existing 2.00 Each 1596.81

hook or clamp with earthing. [Make shall be approved by

Engineer in charge]

Name of Work : Construction of Ladies & Gents Toilet Block at Decomposite Site, AT Karamsad Anand

Municipal Corporatrion.

Abstract of Schedule-B2.5

Item Description Quantity Unit Amount

Excavation for foundation upto 1.5 m depth including

sorting out and stacking of useful materials and

disposing off the excavated stuff upto 50 Meter lead.(A)

Loose or soft soil

Providing and laying cement concrete work 1:2:4 (1-

Cement : 2- Coarse sand : 4- graded stone aggregates

mm nominal size) and curing complete excluding cost of

formwork and reinforcement for reinforced concrete

work in (A) Foundations (upto 10 ton)

Providing & laying controlled cement concrete M-250

with curing etc. complete incl. the cost of form work but

excluding the cost of reinforcement for R.C.C. work for

Providing & laying controlled cement concrete M-250

with curing etc. complete incl. the cost of form work but

4 excluding the cost of reinforcement for R.C.C. work for 2.00 Cu.m. 7440.59

column up to plinth.

Providing & laying controlled cement concrete M-250

with curing etc. complete incl. the cost of form work but

5 excluding the cost of reinforcement for R.C.C. work for 4.00 Cu.m. 5717.23

Ground beam & Plinth beams etc.

Providing & laying controlled cement concrete M-250

with curing etc. complete including the cost of form work

6 but excluding the cost of reinforcement for R.C.C. work in 0.90 Cu.m. 5746.55

foundation and plinth for Copping & Beam etc.

Filling availabale excavated earth (excluding rock) in

trenches plinth, sides of founadions etc. in layers not

7 exceeding 20cm in depth consolidating each depo sited 26.00 Cu.m. 136.92

layer by ramming and watering

Filling in foundation and plinth with murrum or selected

8 soil in layers of 20cm thickness including watering 8.00 Cu.m. 294.38

rammingand consolidating etc. complete

Carring out plinth treatment to post construction existing

structure by spraying chemical solution for termite

control treatment including labour and material

consistment with I.S.I specification. Using ehlordene and

ehiorpurfiles 20 EC. As Per 6131_paret-ll eonsentration

9 Weight one percent is recommended i.e one litre 20 Ee 17.00 Sqm 124.35

chemical emulsion with 19 liter give 1 % concrentration

inclusive of one litre chemical emulsion appication at the

rate of 5 Litre chemical I Sqm of surface is recommended

Providing & laying controlled cement concrete M-250

with curing etc. complete including the cost of form work

10 but excluding the cost of reinforcement for R.C.C. work at 2.00 Cu.m. 7177.12

Ground Floor for Column.

Providing & laying controlled cement concrete M-250

with curing etc. complete including the cost of form work

11 but excluding the cost of reinforcement for R.C.C. work at 4.00 Cu.m. 6445.06

Ground Floor for Beam

Providing and Laying controlled Cement Concrete M-250

and curing etc. Complete including the cost of form work

12 but excluding the cost of reinforcement for R.C.C. work at 4.00 Cu.m. 6471.83

Ground Floor for Slabs & Shelves etc.

Providing & laying controlled cement concrete M-250

with curing etc. complete including the cost of form work

13 but excluding the cost of reinforcement for R.C.C. work at 1.00 Cu.m. 6445.06

Ground Floor for Lintel.

Providing & laying controlled cement concrete M-250

with curing etc. complete including the cost of form work

14 but excluding the cost of reinforcement for R.C.C. work at 0.60 Cu.m. 6445.06

Ground Floor for Chajja.

Providing TMT Bar FE 500D reinforcement for R.C.C.

15 work including bending, binding and placing in position 3875.00 Kg 77.29

complete upto floor two level

Brick work using common burnt clay building brick

having crushing strength not less than 35 kg/sq. cm. in

brick in super structure above plinth level up to floor

two level in cement mortar 1:6 (1 Cement : 6 fine

sand) (B) Conventional

(i) Half brick masonry in common brunt clay building

bricks having crushing strength not less than

17 Kg/Sq.Cm. in Cement mortar 1:4 (1- Cement : 4 -coarse 16.00 Sq.m. 629.84

sand ) in foundation and plinth (B) Conventional

Providing 15mm thick cement plaster in single coat on

Rough (Similar)side of single or half brick walls for

interior plastering upto floor two level and finished even

18 and smooth in (i) Cement mortar 1:3 (1-cement:3-sand) 91.00 Sqm 254.40

and finishing with a floating coat of neat cement slurry.

Providing 15mm thick cement plaster in single coat on

brick/concrete walls for interior plastering upto floor two

level and finished even and smooth in (i) Cement mortar

1:3 (1-cement:3-sand) plastering on ceilings and soffits

of stairs upto floor two level instead of plastering on

walls. finishing with a floating coat of neat cement slurry.

20 mm. thick sand faced cement plaster on wall upto

height 10 metres above ground level consisting of 12mm

20 thickbacking coat of c.m. 1 : 3 (1 cement : 3 sand) and 8 59.00 Sqm 352.44

mm thick finishing coat of c.m. 1 : 1 (1 cement : 1 sand)

Finishing wall with weather proof exterior emulsion paint

on wall surface (two coats) to give an required shape

even shade after thoroughly brushing the surface to

remove all dirt, and remains of loose powdered materials

Applying two coats of Birla or Asian acrylic lappy (

putty) and two coats of primer of approved brand

and manufacture on new wall surface to give an even

22 shade including thoroughly brushing the surface free 108.00 Sqm 40.59

from mortar dropping and other foreign matter and sand

papered smooth.

Wall painting (two coats) with plastic emulsion paint of

approved brand and manufacture on undecorated wall

surface to give an even shade including throughly

brushing the surface free from mortar droppings and

other foreign matter and sand papered smooth.

Providing and fixing 35 mm thick shutters for Doors,

windows and clerestory windows including Indian teak

wood frames 10 cm x 7 cm. size including anodized

24 alluminium fixtures and fastenings including primer coat 6.00 Sqm 5338.30

of approved quality and two coats of oil painting etc,

complete. (ii) Fully Panelled.

Providing and fixing FRP frame size 125x65 mm and

35mm thick FRP shutter with wood grain raised

panneled design finish shutter having extra

reinforcement on sides & edges in Gel coat finish. The

core of the shutter & frame is to be filed up with injected

polyurethene foam done in situ alongwith embedded

25 wooden pieces for stiffening & also taking hinges & 8.00 Sqm 2019.98

fintures. The whole FRP frame & shutter is to be water

proof weather proof, termite proof & resistance to mild

acid/alkali. Rates are to be inclusive of S.S hinges with

fastener sleeve & alluminium fixtures & fastenings.

Providing and fixing standared extruded of alluminium

section of size 63mm x 38.10mm x 1.2mm (Jindal

Section:2434, @ Wt. 0.643 Kg/mt) with colour Powder

Coated alluminium frame for ventilation with 5 mm thick

frosted glass as details etc complete for Ventilation

Providing and laying Mirror polished Machine polished

Telephone Black Madras Granite stone slab 18mm

(Average) thick for Door / Windows Sill & Jams Cladding

as per Design incl. full moulded round front edge in trade

27 of steps laid on 10 mm thick cement mortar 1: 3 (1 5.00 Sqm 2705.45

cement: 3 coarse sand) jointed with grey cement slurry

including rubbing and polishing etc. complete. For Door /

Windows Sill & Jams Cladding.

Providing and fixing M.S. grills of required pattern to

wooden frames of windows etc. with M.S. flats at required

28 spacings and frame alround, square or round bars with 486.00 Kg 106.23

round headed bolts and nuts or by screws (A) Plain Grill.

Painting two coats (excluding priming coat) on new steel

and other metal surface with enamel paint, brushing,

interior to give an even shade including cleaning the

surface an even shade including cleanicn the surface of all

dirt, dust and other foreign matter.

Providing and laying China Mosaic type water proofing

treatment on terrace including applying neat cement

slurry2.75 kg./sq.mt on cement admixed with water

proofing component after cleaning the surface, laying

cement concrete with brick bat 75mm to 100mm thick

with 50% of C.M. 1 : 5 admixed with water proofing

component over 20mm thick layer of C.M. 1 : 5 to

required slope including ramming at junction of wall and

30 slab, after two days of proper curing appliying a second 21.00 Sqm 779.70

coat of cement slurry, finished the surface with 20mm

thick C.M. 1 : 4 china mosaic flooring and finally finished

surface with white cement slurry, after finishing with

terrace shall be finished with water for a period of two

Providing and fixing to wall ceiling and floor

kgf/cSmt working pressure polythelene pipes of the

following outside dia low density complete with special

flage compression type fittings, wall clips etc. including

making good the wall celling and floor. (G) 110mm dia.

Providing cement vata (10 cm x 10 cm size) quarter

32 round in cement mortar 1 :1 including neat cement 19.00 Rmt 24.28

finishing watering etc. complete.

Providing and laying Ceramic tiles 6mm thick in flooring

treads of steps and landing laid on a bed of 12mm thick

33 cement mortar 1:3 (1-cement : 3-coarse sand ) finishing 19.00 Sqm 997.16

with flush pointing in white cement.

Providing and laying white glazed tiles 6mm thick in

skitring risers of steps and dado on 10 mm thick

34 cement plaster 1 : 3 (1 cement : 3 coarse sand) and 66.00 Sqm 985.47

pointing in white cement jointed with white cement

Providing and fixing concealed center point to wall ceiling

& floor CPVC (SDR 13.5) PIPE having National Sanitation

Foundation (NSF) seal for potable water of following dia.

nominal bore tube fitting and clamps including making

good the wall, ceiling and floor etc. complete. [C] 25 mm

Providing and fixing concealed center point to wall ceiling

& floor CPVC (SDR 13.5) PIPE having National Sanitation

Foundation (NSF) seal for potable water of following dia.

nominal bore tube fitting and clamps including making

good the wall, ceiling and floor etc. complete. [A] 15 mm

Providing and fixing in position cowel vent to pipes. (B)

Providing and fixing in position cowel vent to pipes. (C)

Providing and fixing cast iron (spun) nahni trap of

the following nominal diamter of self cleaning design

with C.I screwed down or hinged grating including cost of

cutting and making good the walls and floors 100 mm.

inlet and 50 mm. outlet

Providing and fixing wash down water closet (European

type, W.C. Pan) with integral P or S trap including jointing

the trap with soil pipe in Cement Mortar 1:1 (1-Cement :

1-fine sand) including providing & fixing plastic seat and

cover for wash down WC w

Providing and fixing Urinal or approved quality including

conecting the Urinal with waste pipe , tap etc.

complete.(A) White earthenware flat back or corner type

size 430mm x 260mm x 350mm.

Providing and fixing washbasin with single hole for pillar

tap with C.I. or M.S. brackets painted white including

sutting holes and making good the same but excluding

fittings.(A) Vitreous China:(ii) Flat Back washbasin

mm x v 400mm size. (i) In white colour.

Providing and fixing screw down bib taps of follwing size

43 (A) Brass screw down bib tap polished bright. (ii) 20 8.00 Nos 214.81

Providing and fixing brass screw down stop tap. (A)

Providing and fixing gun metal check or non return

fullway wheel valve (C) 25 mm. dia.

Providing and fixing gun metal check or non return

fullway wheel valve (E) 40 mm. dia.

Providing and fixing chromium plated brass half turn

47 flush cock of approved quality including fixing in pipe line 4.00 Nos 263.77

etc. complete (ii) 25 mm dia

Providing and fixing ball cock of approved quality as

directed. (A) Copper Metal (i) 25 mm. dia.

Providing and fixing C.I. Manhole cover 0.60m x 0.45m.

size having weight not less than 35 kgs.

Providing laying and jointing in true line and level

15mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water

including fittings make PRINCE / SUPREME / ASTRAL /

FINOLEX or equivalent as approved by Engineer In

Charge. Pipe shall be fixed on the wall with the help

50 of clamp at every two metre C/C or shall be 25.00 Rmt 72.65

concelled as directed including necessary fittings etc.

including testing of pipe and joints and fixing the same

with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level

25mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water

including fittings make PRINCE / SUPREME / ASTRAL /

FINOLEX or equivalent as approved by Engineer In

Charge. Pipe shall be fixed on the wall with the help

51 of clamp at every two metre C/C or shall be 110.00 Rmt 91.84

concelled as directed including necessary fittings etc.

including testing of pipe and joints and fixing the same

with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 40 mm

dia. U.P.V.C. Pipe (SCH - 40 ) including fittings of PRINCE /

SUPREME / ASTRAL / FINOLEX or equivalent make or as

approved by Engineer In Charge. Pipe shall be fixed on

the wall with the help of clamp at every two meter C/C or

52 shall be concelled as directed including necessary fittings 120.00 Rmt 148.12

etc. including testing of pipe and joints and fixing the

same with adhesive solvent, including cost of all

Providing laying and jointing in true line and level

diameter U.P.V.C. SWR Type B pipe conforming to IS

13592- 1992 with one end plain and other end socketed

with rubbering, & fitting conforming to ISI 14735-1999 of

approved make for drainage system pipe line, pipe shall

be jointed with each other with rubber lubricant, pipe

shall be fixed on wall using of PVC clamp of the size

53 mm diameter x 210 mm length x 196 mm high at every 30.00 Rmt 834.38

2000 mm center to center or shall be concealed in walls

as directed including necessary fittings such as bends,

shoes etc. includingtesting of pies and joints and jointed

with adhesive solvent cement including cost of all

Providing and fixing PVC SWR Nahni trap IS 14735 for

drain - 100mm diameter with jali of the following

nominal diameter of selfcleansing design with C.I scread

down or hinged grating includingthe cost of cutting and

making good the walls.

Providing and fixing S.W. gully trap with C.I. grating brick

masonry chamber and water tight C.I. cover with frame of

55 300mm x 300mm size (inside) with standard weight.(i) 5.00 Rmt 1246.92

Square mouth traps.(B) 150mm x 100mm size P or R type

Constructing brick masonray road gully chamer

mm x 450 mm x 660 mm including 500mm x

450mm C.I. horizontal grating with frame complete.

Constructing brick masonary road gully chamer

mm x 500 mm x 775 mm including 500 mm x 450 mm

C.I.horizontal grating with frame and vertical grating

Providing erecting and fixing double coated Syntex or

equivalent PVC. (ISI) mark water tank of reqd capacity

each with all necessary fittings & connection etc. comp on

Name of Work : Construction of Rest Office at Decomposite Site, AT Karamsad Anand Municipal

Abstract of Schedule-B2.6

Item Description Quantity Unit Amount

Excavation for foundation upto 1.5 m depth including

sorting out and stacking of useful materials and disposing

1 off the excavated stuff upto 50 Meter lead.(A) Loose or soft 21.00 Cu.m. 122.94

Providing and laying cement concrete work 1:2:4 (1-

Cement : 2- Coarse sand : 4- graded stone aggregates

mm nominal size) and curing complete excluding cost of

formwork and reinforcement for reinforced concrete work

in (A) Foundations (upto 10 ton)

Providing & laying controlled cement concrete M-250 with

curing etc. complete incl. the cost of form work but

excluding the cost of reinforcement for R.C.C. work for

Providing & laying controlled cement concrete M-250 with

curing etc. complete incl. the cost of form work but

4 excluding the cost of reinforcement for R.C.C. work for 1.00 Cu.m. 7440.59

column up to plinth.

Providing & laying controlled cement concrete M-250 with

curing etc. complete incl. the cost of form work but

excluding the cost of reinforcement for R.C.C. work for

Ground beam & Plinth beams etc.

Providing & laying controlled cement concrete M-250 with

curing etc. complete including the cost of form work but

6 excluding the cost of reinforcement for R.C.C. work in 0.70 Cu.m. 5746.55

foundation and plinth for Copping & Beam etc.

Filling availabale excavated earth (excluding rock) in

trenches plinth, sides of founadions etc. in layers not

7 exceeding 20cm in depth consolidating each depo sited 12.00 Cu.m. 136.92

layer by ramming and watering

Filling in foundation and plinth with murrum or selected

8 soil in layers of 20cm thickness including watering 6.00 Cu.m. 294.38

rammingand consolidating etc. complete

Carring out plinth treatment to post construction existing

structure by spraying chemical solution for termite control

treatment including labour and material consistment with

I.S.I specification. Using ehlordene and ehiorpurfiles 20 EC.

As Per 6131_paret-ll eonsentration Weight one percent is

9 recommended i.e one litre 20 Ee chemical emulsion with 19 14.00 Sqm 124.35

liter give 1 % concrentration inclusive of one litre chemical

emulsion appication at the rate of 5 Litre chemical I Sqm of

surface is recommended as per I.S

Providing & laying controlled cement concrete M-250 with

curing etc. complete including the cost of form work but

excluding the cost of reinforcement for R.C.C. work at

Ground Floor for Column.

Providing & laying controlled cement concrete M-250 with

curing etc. complete including the cost of form work but

excluding the cost of reinforcement for R.C.C. work at

Ground Floor for Beam

Providing and Laying controlled Cement Concrete M-250

and curing etc. Complete including the cost of form work

12 but excluding the cost of reinforcement for R.C.C. work at 3.00 Cu.m. 6471.83

Ground Floor for Slabs & Shelves etc.

Providing & laying controlled cement concrete M-250 with

curing etc. complete including the cost of form work but

excluding the cost of reinforcement for R.C.C. work at

Ground Floor for Lintel.

Providing & laying controlled cement concrete M-250 with

curing etc. complete including the cost of form work but

excluding the cost of reinforcement for R.C.C. work at

Ground Floor for Chajja.

Providing TMT Bar FE 500D reinforcement for R.C.C. work

15 including bending, binding and placing in position complete 2760.00 Kg 77.29

upto floor two level

Brick work using common burnt clay building brick having

crushing strength not less than 35 kg/sq. cm. in brick in

16 super structure above plinth level up to floor two level 11.00 Cu.m. 4496.05

in cement mortar 1:6 (1 Cement : 6 fine sand) (B)

(i) Half brick masonry in common brunt clay building bricks

having crushing strength not less than 35 Kg/Sq.Cm. in

17 Cement mortar 1:4 (1- Cement : 4 -coarse sand ) in 22.00 Sq.m. 629.84

foundation and plinth (B) Conventional

Providing 15mm thick cement plaster in single coat on

Rough (Similar)side of single or half brick walls for interior

plastering upto floor two level and finished even and

smooth in (i) Cement mortar 1:3 (1-cement:3-sand) and

finishing with a floating coat of neat cement slurry. (upto

Providing 15mm thick cement plaster in single coat on

brick/concrete walls for interior plastering upto floor two

level and finished even and smooth in (i) Cement mortar

19 1:3 (1-cement:3-sand) plastering on ceilings and soffits of 11.00 Sqm 280.46

stairs upto floor two level instead of plastering on walls.

finishing with a floating coat of neat cement slurry.

20 mm. thick sand faced cement plaster on wall upto height

10 metres above ground level consisting of 12mm

20 thickbacking coat of c.m. 1 : 3 (1 cement : 3 sand) and 8 mm 47.00 Sqm 352.44

thick finishing coat of c.m. 1 : 1 (1 cement : 1 sand) etc.

Finishing wall with weather proof exterior emulsion paint

on wall surface (two coats) to give an required shape even

21 shade after thoroughly brushing the surface to remove all 47.00 Sqm 120.26

dirt, and remains of loose powdered materials etc. complete

Applying two coats of Birla or Asian acrylic lappy (

putty) and two coats of primer of approved brand and

manufacture on new wall surface to give an even shade

22 including thoroughly brushing the surface free from mortar 48.00 Sqm 40.59

dropping and other foreign matter and sand papered

Wall painting (two coats) with plastic emulsion paint of

approved brand and manufacture on undecorated wall

surface to give an even shade including throughly brushing

the surface free from mortar droppings and other foreign

matter and sand papered smooth.

Providing and fixing 35 mm thick shutters for Doors,

windows and clerestory windows including Indian teak

wood frames 10 cm x 7 cm. size including anodized

24 alluminium fixtures and fastenings including primer coat of 3.00 Sqm 5338.30

approved quality and two coats of oil painting etc,

complete. (ii) Fully Panelled.

Providing and fixing FRP frame size 125x65 mm and

35mm thick FRP shutter with wood grain raised

panneled design finish shutter having extra reinforcement

on sides & edges in Gel coat finish. The core of the shutter &

frame is to be filed up with injected polyurethene foam

done in situ alongwith embedded wooden pieces for

25 stiffening & also taking hinges & fintures. The whole FRP 2.00 Sqm 2019.98

frame & shutter is to be water proof weather proof, termite

proof & resistance to mild acid/alkali. Rates are to be

inclusive of S.S hinges with fastener sleeve & alluminium

fixtures & fastenings.

Providing and fixing standared extruded of alluminium

section of size 63mm x 38.10mm x 1.2mm (Jindal

Section:2434, @ Wt. 0.643 Kg/mt) with colour Powder

Coated alluminium frame for ventilation with 5 mm thick

frosted glass as details etc complete for Ventilation

Providing and laying Mirror polished Machine polished

Telephone Black Madras Granite stone slab 18mm

(Average) thick for Door / Windows Sill & Jams Cladding as

per Design incl. full moulded round front edge in trade of

27 steps laid on 10 mm thick cement mortar 1: 3 (1 cement: 3 4.00 Sqm 2705.45

coarse sand) jointed with grey cement slurry including

rubbing and polishing etc. complete. For Door / Windows

Sill & Jams Cladding.

Providing and fixing M.S. grills of required pattern to

wooden frames of windows etc. with M.S. flats at required

28 spacings and frame alround, square or round bars with 459.00 Kg 106.23

round headed bolts and nuts or by screws (A) Plain Grill.

Painting two coats (excluding priming coat) on new steel

and other metal surface with enamel paint, brushing,

interior to give an even shade including cleaning the surface

an even shade including cleanicn the surface of all dirt, dust

and other foreign matter.

Providing and laying China Mosaic type water proofing

treatment on terrace including applying neat cement

slurry2.75 kg./sq.mt on cement admixed with water

proofing component after cleaning the surface, laying

cement concrete with brick bat 75mm to 100mm thick with

50% of C.M. 1 : 5 admixed with water proofing component

over 20mm thick layer of C.M. 1 : 5 to required slope

30 including ramming at junction of wall and slab, after two 14.00 Sqm 779.70

days of proper curing appliying a second coat of cement

slurry, finished the surface with 20mm thick C.M. 1 : 4 china

mosaic flooring and finally finished surface with white

cement slurry, after finishing with terrace shall be finished

with water for a period of two week.

Providing and fixing to wall ceiling and floor

kgf/cSmt working pressure polythelene pipes of the

following outside dia low density complete with special

flage compression type fittings, wall clips etc. including

making good the wall celling and floor. (G) 110mm dia.

Providing cement vata (10 cm x 10 cm size) quarter round

32 in cement mortar 1 :1 including neat cement finishing 16.00 Rmt 24.28

watering etc. complete.

Providing and laying Ceramic tiles 6mm thick in flooring

treads of steps and landing laid on a bed of 12mm thick

33 cement mortar 1:3 (1-cement : 3-coarse sand ) finishing 4.00 Sqm 997.16

with flush pointing in white cement.

Providing and laying white glazed tiles 6mm thick in

skitring risers of steps and dado on 10 mm thick

34 cement plaster 1 : 3 (1 cement : 3 coarse sand) and pointing 10.00 Sqm 985.47

in white cement jointed with white cement slurry.

Providing and fixing concealed center point to wall ceiling

& floor CPVC (SDR 13.5) PIPE having National Sanitation

Foundation (NSF) seal for potable water of following dia.

nominal bore tube fitting and clamps including making

good the wall, ceiling and floor etc. complete. [C] 25 mm

Providing and fixing concealed center point to wall ceiling

& floor CPVC (SDR 13.5) PIPE having National Sanitation

Foundation (NSF) seal for potable water of following dia.

nominal bore tube fitting and clamps including making

good the wall, ceiling and floor etc. complete. [A] 15 mm

Providing and fixing in position cowel vent to pipes. (B)

Providing and fixing in position cowel vent to pipes. (C)

Providing and fixing cast iron (spun) nahni trap of the

following nominal diamter of self cleaning design with C.I

39 screwed down or hinged grating including cost of cutting 1.00 Nos 634.71

and making good the walls and floors 100 mm. inlet and

Providing and fixing wash down water closet (European

type, W.C. Pan) with integral P or S trap including jointing

the trap with soil pipe in Cement Mortar 1:1 (1-Cement : 1-

fine sand) including providing & fixing plastic seat and

cover for wash down WC w

Providing and fixing Urinal or approved quality including

conecting the Urinal with waste pipe , tap etc. complete.(A)

White earthenware flat back or corner type size 430mm x

Providing and fixing washbasin with single hole for pillar

tap with C.I. or M.S. brackets painted white including sutting

holes and making good the same but excluding fittings.(A)

Vitreous China:(ii) Flat Back washbasin 550 mm x v 400mm

size. (i) In white colour.

Providing and fixing screw down bib taps of follwing size

43 (A) Brass screw down bib tap polished bright. (ii) 20 2.00 Nos 214.81

Providing and fixing brass screw down stop tap. (A) 15mm

Providing and fixing gun metal check or non return fullway

wheel valve (C) 25 mm. dia.

Providing and fixing gun metal check or non return fullway

wheel valve (E) 40 mm. dia.

Providing and fixing chromium plated brass half turn flush

47 cock of approved quality including fixing in pipe line etc. 1.00 Nos 263.77

complete (ii) 25 mm dia

Providing and fixing ball cock of approved quality as

directed. (A) Copper Metal (i) 25 mm. dia.

Providing and fixing C.I. Manhole cover 0.60m x 0.45m. size

having weight not less than 35 kgs.

Providing laying and jointing in true line and level

15mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water

including fittings make PRINCE / SUPREME / ASTRAL /

FINOLEX or equivalent as approved by Engineer In Charge.

Pipe shall be fixed on the wall with the help of clamp

50 at every two metre C/C or shall be concelled as 30.00 Rmt 72.65

directed including necessary fittings etc. including testing

of pipe and joints and fixing the same with adhesive

solvent, including cost of all materials.

Providing laying and jointing in true line and level

25mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water

including fittings make PRINCE / SUPREME / ASTRAL /

FINOLEX or equivalent as approved by Engineer In Charge.

Pipe shall be fixed on the wall with the help of clamp

51 at every two metre C/C or shall be concelled as 60.00 Rmt 91.84

directed including necessary fittings etc. including testing

of pipe and joints and fixing the same with adhesive

solvent, including cost of all materials.

Providing laying and jointing in true line and level 40 mm

dia. U.P.V.C. Pipe (SCH - 40 ) including fittings of PRINCE /

SUPREME / ASTRAL / FINOLEX or equivalent make or as

approved by Engineer In Charge. Pipe shall be fixed on the

wall with the help of clamp at every two meter C/C or shall

52 be concelled as directed including necessary fittings etc. 70.00 Rmt 148.12

including testing of pipe and joints and fixing the same with

adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level

diameter U.P.V.C. SWR Type B pipe conforming to IS 13592-

1992 with one end plain and other end socketed with

rubbering, & fitting conforming to ISI 14735-1999 of

approved make for drainage system pipe line, pipe shall be

jointed with each other with rubber lubricant, pipe shall be

fixed on wall using of PVC clamp of the size 160 mm

53 diameter x 210 mm length x 196 mm high at every 2000 100.00 Rmt 834.38

mm center to center or shall be concealed in walls as

directed including necessary fittings such as bends, shoes

etc. includingtesting of pies and joints and jointed with

adhesive solvent cement including cost of all materials

Providing and fixing PVC SWR Nahni trap IS 14735 for

drain - 100mm diameter with jali of the following nominal

54 diameter of selfcleansing design with C.I scread down or 1.00 Nos 586.27

hinged grating includingthe cost of cutting and making

good the walls.

Providing and fixing S.W. gully trap with C.I. grating brick

masonry chamber and water tight C.I. cover with frame of

55 300mm x 300mm size (inside) with standard weight.(i) 1.00 Rmt 1246.92

Square mouth traps.(B) 150mm x 100mm size P or R type

Constructing brick masonray road gully chamer

mm x 450 mm x 660 mm including 500mm x 450mm

C.I. horizontal grating with frame complete.

Constructing brick masonary road gully chamer 1100 mm

x 500 mm x 775 mm including 500 mm x 450 mm

C.I.horizontal grating with frame and vertical grating

Providing erecting and fixing double coated Syntex or

equivalent PVC. (ISI) mark water tank of reqd capacity each

with all necessary fittings & connection etc. comp on

Name of Work : Construction of Office & Conference Room at Decomposite Site, AT Karamsad Anand

Municipal Corporatrion.

Abstract of Schedule-B2.7

Description Qty Unit Amount

Excavation for foundation upto 1.5 m depth including sorting

out and stacking of useful materials and disposing off the

excavated stuff upto 50 Meter lead. (A) Loose or soft soil

Providing and laying cement concrete work 1:2:4 (1- Cement : 2-

Coarse sand : 4- graded stone aggregates 20 mm nominal size)

2 and curing complete excluding cost of formwork and 14.00 cu.m 4046.42

reinforcement for reinforced concrete work in (A) Foundations

Providing & laying controlled cement concrete M-250 with

curing etc. complete incl. the cost of form work but excluding

the cost of reinforcement for R.C.C. work for Footings.

Providing & laying controlled cement concrete M-250 with

curing etc. complete incl. the cost of form work but excluding

the cost of reinforcement for R.C.C. work for column up to

Providing & laying controlled cement concrete M-250 with

curing etc. complete incl. the cost of form work but excluding

the cost of reinforcement for R.C.C. work for Ground beam &

Plinth beams etc.

Providing & laying controlled cement concrete M-250 with

curing etc. complete including the cost of form work but

excluding the cost of reinforcement for R.C.C. work in

foundation and plinth for Copping & Beam etc.

Filling available excavated earth (excluding rock) in trenches

,plinth, sides of foundations etc.in layers not exceeding 20cm in

depth consolidating each deposited layer by ramming &

Filling in foundation and plinth with murrum or selected soil in

8 layers of 20cm thickness including watering rammingand 27.00 Cu.m. 294.38

consolidating etc. complete

Carring out plinth treatment to post construction existing

structure by spraying chemical solution for termite control

treatment including labour and material consistment with I.S.I

specification. Using ehlordene and ehiorpurfiles 20 EC. As Per

9 6131_paret-ll eonsentration Weight one percent is 45.00 Sqm 124.35

recommended i.e one litre 20 Ee chemical emulsion with

liter give 1 % concrentration inclusive of one litre chemical

emulsion appication at the rate of 5 Litre chemical I Sqm of

surface is recommended as per I.S

Providing & laying controlled cement concrete M-250 with

curing etc. complete including the cost of form work but

excluding the cost of reinforcement for R.C.C. work at Ground

Floor for Column.

Providing & laying controlled cement concrete M-250 with

curing etc. complete including the cost of form work but

excluding the cost of reinforcement for R.C.C. work at Ground

Providing and Laying controlled Cement Concrete M-250 and

curing etc. Complete including the cost of form work but

excluding the cost of reinforcement for R.C.C. work at Ground

Floor for Slabs & Shelves etc.

Providing & laying controlled cement concrete M-250 with

curing etc. complete including the cost of form work but

excluding the cost of reinforcement for R.C.C. work at Ground

Floor for Lintel

Providing & laying controlled cement concrete M-250 with

curing etc. complete including the cost of form work but

excluding the cost of reinforcement for R.C.C. work at Ground

Floor forr Chajja.

Providing TMT Bar FE 500/500D reinforcement for R.C.C. work

15 including bending, binding and placing in position complete 6110.00 Kg 77.29

upto floor two level. (upto 10 ton)

Brick work using common burnt clay building bricks having

crushing strength not less than 35 kg./Sq.Cm. in foundation and

plinth in Cement Mortar 1:6 (1- Cement : 6 -fine sand) Extra for

brick work in superstructure above plinth level upto floor two

level (B) Conventional (upto 10 ton)

Providing 15mm thick cement plaster in single coat on Rough

(Similar)side of single or half brick walls for interior plastering

upto floor two level and finished even and smooth in (i) Cement

mortar 1:3 (1-cement:3-sand) and finishing with a floating coat

of neat cement slurry. (upto 10 ton)

Providing 15mm thick cement plaster in single coat on

brick/concrete walls for interior plastering upto floor two level

and finished even and smooth in (i) Cement mortar 1:3 (1-

cement:3-sand) plastering on ceilings and soffits of stairs upto

floor two level instead of plastering on walls. finishing with a

floating coat of neat cement slurry.

20 mm. thick sand faced cement plaster on wall upto height

meters above ground level consisting of 12mm thick backing

16 coat of c.m. 1 : 3 (1 cement : 3 sand) and 8 mm thick finishing 121.00 Sqm 352.44

coat of c.m. 1 : 1 (1 cement : 1 sand) etc. complete

Finishing wall with weather proof exterior emulsion paint on

wall surface (two coats) to give an required shape even shade

17 after thoroughly brushing the surface to remove all dirt, and 121.00 Sqm 120.26

remains of loose powdered materials etc. complete

Applying two coats of Birla(white cement based) or Asian

(acrylic lapy putty) or equivalent & two coats of primer of

approved brand and manufacture on new wall surface to give an

even shade including thoroughly brushing the surface free from

mortar dropping and other foreign matter and sand papered

Wall painting (two coats) with plastic emulsion paint of

approved brand and manufacture on undecorated wall surface

19 to give an even shade including throughly brushing the surface 171.00 Sqm 82.85

free from mortar droppings and other foreign matter and sand

papered smooth.

Providing and fixing 35 mm thick shutters for Doors, windows

and clerestory windows including Indian teak wood frames

cm x 7 cm. size including anodized alluminium fixtures and

fastenings including primer coat of approved quality and two

coats of oil painting etc, complete. (ii) Fully Panelled.

Providing and laying polished kota stone slab flooring over

mm (average) thick base of cement mortar 1 : 6 (1 cement :

21 course sand) laid over and jointed with grey cement slurry 49.00 Sqm 1019.39

including rubbing and polishing etc. complete (A) 25 mm thick

Providing and laying polished kota stone slab 25mm thick in

risers of steps,skirting Dedo and pillars laid on 10mm thick

cement mortar 1:3 (1-Cement : 3 coarse sand) and jointed with

gray cement slury mixed with pigment to match the shade of

slab including rubbing and polishing etc. complete. (upto

Providing and fixing window having extruded aluminium Colour

anodized section frame main outer size 63.50 x 38.10 x

mm(of Jindal Section no:4605,@ Wt 1.094 Kg / Rmt), horizontal

two track member size 61.85 mm x 31.75 mm x 1.20mm (of

Jindal Section no: 8687 @ wt.of 0.695 Kg/mt), vertical member

of size 61.85 mm x 31.75mm x 1.30 mm (of Jindal Section

no:8758 @ wt.of 0.0.659 Kg/mt) with sliding shutters of

horizontal member size 40mm x 18mm x 1.29mm (of Jindal

Section no:8949 @ wt.of 0.456Kg/mt), vertical member of size

40mm x 18mm x 1.29mm (of Jindal Section no:8947 @ wt.of

0.456Kg/mt/ Section 8948, @ Wt. 0.457 Kg/mt) with 5 mm

thick transparent bronze colour tinted float glass with powder

coated aluminium fittings and fixtures and transparent silicon

sealant glass fixing to frame as per details etc. complete for

Providing and fixing M.S. grills of required pattern to wooden

frames of windows etc. with M.S. flats at required spacings and

24 frame alround, square or round bars with round headed bolts 558.00 Kg 106.23

and nuts or by screws (A) Plain Grill. (upto 10 ton)

Painting two coats (excluding priming coat) on new steel and

other metal surface with enamel paint, brushing, interior to give

25 an even shade including cleaning the surface an even shade 5.00 Sqm 92.20

including cleanicn the surface of all dirt, dust and other foreign

Providing and laying broken chine mosaic flooring for terrace

using 12 mm to 20 mm broken pieces of glazed tiles to be laid

over cement mortar 1:3 to plain or slope and to be tempered to

26 bring mortar cream out upto surface using white cement 49.00 Sqm 779.70

including rounding off junctions and extending them upto 15 cm

along the wall, clearing with water and oxalic acid etc. as

Point wiring for Light / Fan/ Bell/ Primary Point with 2-1.5 sq.

mm & earth wire of 1.5 sq. mm (green) both are of ISI marked

1.1 kv grade FRLS PVC insulated multi strand copper wires

upto max length of 10 mt, in below type of pipe erected with 6A

Tissino Type ISI marked flush type switch / bell push and

accessories erected on Metal / PVC/Wooden Box covered with

3 mm thick PC(Polycarbonate) /Acrylic/Laminated sheet. with

necessary Lamp holder/ceiling rose / H.D.Connector as

directed. (b) with 16 swg(1.6 mm thick) HGS metal conduit

pipe and accessories painted black erected flushed on

wall/ceiling complete

Providing & erecting 240 V MCB double pole switch for motor &

inductive load (C Curve) having 10 KA breaking capacity &

confirms to IS : 8828 in existing box having following capacity

(B) 40 Amp Cat-III.

Providing and erecting Approved make Ceiling fan with double

ball bearing ISI mark with condenser A.C. 23OV.50 c/s.1200

29 mm. sweep complete, canopy erected on existing hook or clamp 4.00 Each 1596.81

with earthing. [Make shall be approved by Engineer in charge]

Name of Work : Construction of Change Room at Decomposite Site, AT Karamsad Anand Municipal

Abstract of Schedule-B2.8

Description Qty Unit Amount

Excavation for foundation upto 1.5 m depth including sorting out

and stacking of useful materials and disposing off the excavated

stuff upto 50 Meter lead. (A) Loose or soft soil

Providing and laying cement concrete work 1:2:4 (1- Cement : 2-

Coarse sand : 4- graded stone aggregates 20 mm nominal size)

2 and curing complete excluding cost of formwork and 14.00 cu.m 4046.42

reinforcement for reinforced concrete work in (A) Foundations

Providing & laying controlled cement concrete M-250 with

curing etc. complete incl. the cost of form work but excluding the

cost of reinforcement for R.C.C. work for Footings.

Providing & laying controlled cement concrete M-250 with

curing etc. complete incl. the cost of form work but excluding the

cost of reinforcement for R.C.C. work for column up to plinth.

Providing & laying controlled cement concrete M-250 with

curing etc. complete incl. the cost of form work but excluding the

cost of reinforcement for R.C.C. work for Ground beam & Plinth

Providing & laying controlled cement concrete M-250 with

curing etc. complete including the cost of form work but

excluding the cost of reinforcement for R.C.C. work in foundation

and plinth for Copping & Beam etc.

Filling available excavated earth (excluding rock) in trenches

,plinth, sides of foundations etc.in layers not exceeding 20cm in

depth consolidating each deposited layer by ramming &

Filling in foundation and plinth with murrum or selected soil in

8 layers of 20cm thickness including watering rammingand 24.00 Cu.m. 294.38

consolidating etc. complete

Carring out plinth treatment to post construction existing

structure by spraying chemical solution for termite control

treatment including labour and material consistment with I.S.I

specification. Using ehlordene and ehiorpurfiles 20 EC. As Per

9 6131_paret-ll eonsentration Weight one percent is 40.00 Sqm 124.35

recommended i.e one litre 20 Ee chemical emulsion with 19 liter

give 1 % concrentration inclusive of one litre chemical emulsion

appication at the rate of 5 Litre chemical I Sqm of surface is

recommended as per I.S

Providing & laying controlled cement concrete M-250 with

curing etc. complete including the cost of form work but

excluding the cost of reinforcement for R.C.C. work at Ground

Floor for Column.

Providing & laying controlled cement concrete M-250 with

curing etc. complete including the cost of form work but

excluding the cost of reinforcement for R.C.C. work at Ground

Providing and Laying controlled Cement Concrete M-250 and

curing etc. Complete including the cost of form work but

excluding the cost of reinforcement for R.C.C. work at Ground

Floor for Slabs & Shelves etc.

Providing & laying controlled cement concrete M-250 with

curing etc. complete including the cost of form work but

excluding the cost of reinforcement for R.C.C. work at Ground

Floor for Lintel

Providing and laying cement concrete M.200 for Providing &

laying controlled cement concrete M-250 with curing etc.

14 complete including the cost of form work but excluding the cost 2.00 cu.m 6445.06

of reinforcement for R.C.C. work at Ground Floor for Chajja.

Providing TMT Bar FE 500/500D reinforcement for R.C.C. work

15 including bending, binding and placing in position complete upto 6110.00 Kg 77.29

floor two level. (upto 10 ton)

Brick work using common burnt clay building bricks having

crushing strength not less than 35 kg./Sq.Cm. in foundation and

16 plinth in Cement Mortar 1:6 (1- Cement : 6 -fine sand) Extra for 25.00 cu.m 4496.05

brick work in superstructure above plinth level upto floor two

level (B) Conventional (upto 10 ton)

Providing 15mm thick cement plaster in single coat on Rough

(Similar)side of single or half brick walls for interior plastering

upto floor two level and finished even and smooth in (i) Cement

mortar 1:3 (1-cement:3-sand) and finishing with a floating coat

of neat cement slurry. (upto 10 ton)

Providing 15mm thick cement plaster in single coat on

brick/concrete walls for interior plastering upto floor two level

and finished even and smooth in (i) Cement mortar 1:3 (1-

cement:3-sand) plastering on ceilings and soffits of stairs upto

floor two level instead of plastering on walls. finishing with a

floating coat of neat cement slurry.

20 mm. thick sand faced cement plaster on wall upto height

meters above ground level consisting of 12mm thick backing

coat of c.m. 1 : 3 (1 cement : 3 sand) and 8 mm thick finishing

coat of c.m. 1 : 1 (1 cement : 1 sand) etc. complete

Finishing wall with weather proof exterior emulsion paint on

wall surface (two coats) to give an required shape even shade

after thoroughly brushing the surface to remove all dirt, and

remains of loose powdered materials etc. complete

Applying two coats of Birla(white cement based) or Asian

(acrylic lapy putty) or equivalent & two coats of primer of

approved brand and manufacture on new wall surface to give an

even shade including thoroughly brushing the surface free from

mortar dropping and other foreign matter and sand papered

Wall painting (two coats) with plastic emulsion paint of

approved brand and manufacture on undecorated wall surface to

19 give an even shade including throughly brushing the surface free 162.00 Sqm 82.85

from mortar droppings and other foreign matter and sand

papered smooth.

Providing and fixing 35 mm thick shutters for Doors, windows

and clerestory windows including Indian teak wood frames

cm x 7 cm. size including anodized alluminium fixtures and

fastenings including primer coat of approved quality and two

coats of oil painting etc, complete. (ii) Fully Panelled.

Providing and laying polished kota stone slab flooring over

mm (average) thick base of cement mortar 1 : 6 (1 cement :

21 course sand) laid over and jointed with grey cement slurry 46.00 Sqm 1019.39

including rubbing and polishing etc. complete (A) 25 mm thick

Providing and laying polished kota stone slab 25mm thick in

risers of steps,skirting Dedo and pillars laid on 10mm thick

cement mortar 1:3 (1-Cement : 3 coarse sand) and jointed with

gray cement slury mixed with pigment to match the shade of slab

including rubbing and polishing etc. complete. (upto 10 ton)

Providing and fixing window having extruded aluminium Colour

anodized section frame main outer size 63.50 x 38.10 x

mm(of Jindal Section no:4605,@ Wt 1.094 Kg / Rmt), horizontal

two track member size 61.85 mm x 31.75 mm x 1.20mm (of

Jindal Section no: 8687 @ wt.of 0.695 Kg/mt), vertical member

of size 61.85 mm x 31.75mm x 1.30 mm (of Jindal Section

no:8758 @ wt.of 0.0.659 Kg/mt) with sliding shutters of

23 horizontal member size 40mm x 18mm x 1.29mm (of Jindal 6.00 Sqm 1713.70

Section no:8949 @ wt.of 0.456Kg/mt), vertical member of size

40mm x 18mm x 1.29mm (of Jindal Section no:8947 @ wt.of

0.456Kg/mt/ Section 8948, @ Wt. 0.457 Kg/mt) with 5 mm thick

transparent bronze colour tinted float glass with powder coated

aluminium fittings and fixtures and transparent silicon sealant

glass fixing to frame as per details etc. complete for window.

Providing and fixing M.S. grills of required pattern to wooden

frames of windows etc. with M.S. flats at required spacings and

24 frame alround, square or round bars with round headed bolts 644.00 Kg 106.23

and nuts or by screws (A) Plain Grill. (upto 10 ton)

Painting two coats (excluding priming coat) on new steel and

other metal surface with enamel paint, brushing, interior to give

25 an even shade including cleaning the surface an even shade 6.00 Sqm 92.20

including cleanicn the surface of all dirt, dust and other foreign

Providing and laying broken chine mosaic flooring for terrace

using 12 mm to 20 mm broken pieces of glazed tiles to be laid

over cement mortar 1:3 to plain or slope and to be tempered to

26 bring mortar cream out upto surface using white cement 46.00 Sqm 779.70

including rounding off junctions and extending them upto 15 cm

along the wall, clearing with water and oxalic acid etc. as

Point wiring for Light / Fan/ Bell/ Primary Point with 2-1.5 sq.

mm & earth wire of 1.5 sq. mm (green) both are of ISI marked

1.1 kv grade FRLS PVC insulated multi strand copper wires upto

max length of 10 mt, in below type of pipe erected with 6A

Tissino Type ISI marked flush type switch / bell push and

accessories erected on Metal / PVC/Wooden Box covered with

3 mm thick PC(Polycarbonate) /Acrylic/Laminated sheet. with

necessary Lamp holder/ceiling rose / H.D.Connector as directed.

(b) with 16 swg(1.6 mm thick) HGS metal conduit pipe and

accessories painted black erected flushed on wall/ceiling

Providing & erecting 240 V MCB double pole switch for motor &

inductive load (C Curve) having 10 KA breaking capacity &

confirms to IS : 8828 in existing box having following capacity

(B) 40 Amp Cat-III.

Providing and erecting Approved make Ceiling fan with double

ball bearing ISI mark with condenser A.C. 23OV.50 c/s.1200

29 mm. sweep complete, canopy erected on existing hook or clamp 8.00 Each 1596.81

with earthing. [Make shall be approved by Engineer in charge]

Name of Work : Estimate of Material Recovery Facility Shed Electrical Work at Decomposite Site, AT Karamasad

Anand Municipal Corporatrion.

Abstract of Schedule-B2.9

Qty Item Total Rate Per Amount

Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of

sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC

insulated multi strand copper wires up to 10 mtr length , in

below type of pipe erected with 6A Modular type switch / bell

push & accessories and earth continuity of following type, erected on

PVC / Metallic/Wooden box, single mounting base frame covered

1 100.00 with textured/metallic/white front plate modules erected on / in 449.45 Pt

wall / ceiling as per pipe erected, with necessary Lamp

holder/ceiling rose / H.D.Connector as directed. (f) with medium class

Rigid PVC pipe and accessories erected concealed in wall/ceiling

complete CATIII

Point wiring for FAN with 2-1.5 sq.mm & earth wire of

sq.mm (Green) both are of .ISI marked 1.1 KV Grade FRLS PVC

insulated multi strand copper wires up to 10 mtr length, in below type

of pipe erected with 6A Modular type switch and hum free EME step

type electronic fan regulator mounted and accessories with

earth continuity of following type erected on PVC / Metallic/Wooden

2 60.00 box, single mounting base frame covered with 629.23 Pt

textured/metallic/white front plate modules erected on / in wall /

ceiling as per pipe erected. with necessary ceiling rose /

H.D.Connector as directed. (f) with medium class Rigid PVC pipe

and accessories erected concealed in wall/ceiling complete CATIII

Point wiring for on board Looped Plug with 6A Modular type switch &

5 pin socket erected on PVC / Metallic/Wooden box, single

mounting base frame covered with textured / metallic/white

3 70.00 front plate modules erected on / in wall / ceiling with following 241.39 Pt

accessories Cat. III

Point wiring for Individual Plug with & earth wire of 1.5 sq.mm

(Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated

multi strand copper wires up to 10 mtr length, in below type of pipe

erected complete with Modular type switch & 5 pin Plug erected on

4 PVC / Metallic/Wooden box covered with appropriate front plate

modules erected on / in wall / ceiling as per pipe erected with

following type of accessories.

[I] For 6A Plug and 6 a switch with 2-1.5 sq.mm Cu. Wire from

nearby switchboard/mcb db board (f) with medium class Rigid PVC

pipe and accessories erected concealed in wall/ceiling complete

Point wiring for Individual Plug with & earth wire of 1.5 sq.mm

(Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated

multi strand copper wires up to 10 mtr length, in below type of pipe

erected complete with Modular type switch & 5 pin Plug erected on

5 PVC / Metallic/Wooden box covered with appropriate front plate

modules erected on / in wall / ceiling as per pipe erected with

following type of accessories.

[II] For 16A Plug and 16 amp switch with 2-2.5 sq.mm Cu. Wire from

mcb db board. (f) with medium class Rigid PVC pipe and accessories

erected concealed in wall/ceiling complete

Providing and erecting Sheet Steel powder coated MCB distribution

board - flush / surface mounted fitted with busbar, neutral link, earth

bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 &

without MCB to house appropriate nos. of MCBs.(The DBs should be

6 25.00 used of same company of MCB to be used) suitable for (A) 582.77 Ea.

single phase incoming and horizontal single phase outgoing (a) single

(IP-30) (ii) 6 way

providing and erecting Approved make RCCBs conforming to IS:

12640 and having sensitivity of 30 mA and Short Circuit

withstand capacity of 10 KA and suitable for operation on single

phase 240 V,50Hz. having characteristic of quick action & tripping

7 10.00 with all advance feature & do not incorporate any electronic 2235.13 Ea.

component. for following Max. rating erected as directed. (ii)

40Amps. DP, CAT - III

providing and erecting Miniature circuit breaker single pole 6A

to 25A suitable to operate on 240 V A.C. system and having

8 20.00 breaking capacity 10 KA to be erected in existing box. 112.11 Ea.

confirming to IS 8828/1996 with ISI Mark CAT - III

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable

Aluminium conductor for 1.1 KV. to be laid on wall with necessary

9 1256.38 clamps or in existing trench / pipe of following size of cables. (B) 2 90.90 Rmt

Supplying & erecting energy saving Energy Efficient E+ (1 - 4 ft)

watt retrofit tube fitting with one no 28watt T-5 tube

complete with E.G.P. wings reflector / clear acrylic guard cover

& tube and electronic inbuilt circuit ballast of rating 130 to

A.C. The fittings should be able to fit in any conventional existing T -

tube fittings complete erected in an approved manner. - Cat-III

Supply, Installation, Testing and Commissioning of suitable sweep,

BEE 5 Star rated, Ceiling fan with Brush Less Direct Current

(BLDC) permanent ferrite magnet Motor, class of insulation: B,

Rust free 3 nos.Aluminium blades, 2 nos. canopies, shackle kit

with earthing provision, copper winding, Power factor not < 0.9,

Service Value (CMM/W) minimum 6.85, Air delivery minimum

215 CMM, 350 RPM,230v (tolerance as per IS : 374-2019), THD <

11 20.00 10%, with remote unit for Speed Control and all remaining 2885.57 Ea.

accessories including safety pin, nut bolts, washers, temperature

rise = 75 degree C (Max.), suitable for 140 to 285 Voltage and

rectifier circuit with surge, over current and overload protection

50 Hz, Single phase AC Supply, earthing etc. Complete as

required.[ Make shall be approved by Engineer in Charge] (B)

Supplying and erecting 19 / 20 mm. nominal bore Medium

Class M.S. Pipe down rod erected duly painted for fan

complete with proper insulation without leakage and earthing.

Supplying & erecting approved make low noise decorative

exhaust fan having square frame ABS body with inbuilt lowers &

frame. 200mm with 1350RPM Cat.II

PVC snap- on adaptable trunking/Pop up Box with required

items erected with necessary connection. As desired by Engineer In

charge iii) Bell Push 6 A SP 1 Way cat-III

Supplying & erecting earth pit of minimum bore dia.150mm size

approved make Earthing Electrode consisting Pipe-in-Pipe

Technology as per IS 3043-1987 made of corrosion free hot dipped

G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron

galvanising, Inner pipe dia of 25 mm having 200-250 Micron

galvanising, connection terminal dia of 12mm with constant

ohmic value surrounded by highly conductive compound with high

charge dissipation suitable for following type of applications with

chamber and heavy duty cover. (A)(approved make OEM has to

submit test certificate including value of earth resistance of

installation duly stamped and signed by agency and officer

15 Incharge has to ensure the value of earthing resistane mentioned

in test Certificate) & having back filling compound of (B)

Inner chemical (CCM Compound)- Resistivity:- 0.2 ohm / meter

testing as per IEC 62561- 2017, Voltage drop:- < 1 volt at no load &

dry form, Sulphar content:

<2%(C) Back fill Compound :- Earthing compound should be

capable to retain moisture for long time Necessary test report must

be submitted by Agency.

(a) For Electrical Installation up to 440V in normal soil Length of pipe -

20.00 1 Mtr Back filling compound - 1 Nos Bag of 15 Kg. 4591.46 No

Supplying and erecting LED street light / Flood light fittings

with High power White LEDs wattage of 3 Watt and above

assembled on single MCPCB, efficiency more than 130 lm/w and

corrosion free High pressure die cast aluminum housing with

smooth finish powder coated and heat sink extruded

aluminium with diffuser and Polycarbonate optics/ lenses,

with toughened glass with company mark/name engraved or

embossed 160 to 270 V,Power Factor more than 0.95, THD <

10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45, Luminaire

efficacy> 100 lumens/watt . LED driver efficiency

16 48.00 > 85 %.( fittings required LM-79 & LM-80 certificates)(NOTE: Below 6566.01 No

description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity

between the ranges shown.) (A) Street Light (IP-65), Surge

protection -4KV integral and, Light must have 440VAC line supply

with over-voltage protection.(iv) Above 90 to 120 watts Cat-lll

Supplying and erecting B class galvanised iron pipe 32 mm outside

dia 45 cm long duly welded on 20 cm x 20 cm x 3 mm thick

17 20.00 M.S. base plate, erected on wall or corner for mounting street 343.40 No

light luminaire with necessary hardware materials duly painted.

Supplying and erecting Flexible PVC insulated multi strand multi core

1.1 kv grade ISI marked copper wires of following size to be erected

as directed. (e) 1.50 Sq.mm 3 core round PVC sheathed

Providing & laying approved make Double walled corrugated pipes

(DWC) of polyethylene(conforming to IS 14930 II )with necessary

connecting accessories of same material at required depth in

existing trench for laying of cable. below ground / road surface for

enclosing cable (A)50 mm outer dia

Providing following type of Modular Type Accessories mounted with

PVC / metallic/Wooden box, single mounting base frame covered

with textured / metallic/white front plate , modules erected with

necessary connections as per site situation directed by Engineer

20 25.00 In charge. (13) 6A/10A/16A/20A/25A/32A Single pole Modular 295.93 Pt

Name of Work : Providing Streetlight Pole at Decomposite Site, AT Dry Waste Processing Plant For

Karamsad Anand Municipal Corporatrion.

Abstract Schedule-B2.10

Description Quantity Unit Amount

Supplying and erecting Flexible PVC insulated multistrand

multicore 1.1 kv grade ISI marked copper wires of

following size to be erected as directed. e) 1.50 Sq.mm

core round PVC sheathed

Supplying and erecting LED street light / Flood light

fittings with High power White LEDs wattage of 3 Watt

and above assembled on single MCPCB, efficiency more

than 130 lm/w and corrosion free High pressure die cast

aluminum housing with smooth finish powder coated and

heat sink extruded aluminium with diffuser and

Polycarbonate optics/ lenses, with toughened glass with

company mark/name engraved or embossed 160 to

V,Power Factor more than 0.95, THD < 10 %, CCT 3000 K

to 5700K,Uniformity ratio >0.45, Luminaire efficacy>

lumens/watt . LED driver efficiency > 85 %.( fittings

required LM-79 & LM-80 certificates) (NOTE: Below

description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage

capacity between the ranges shown.) (A) Street Light (IP-

65), Surge protection -4KV integral and ,Light must have

440VAC line supply with over-voltage protection. (ii)

above 48 to 60 Watts. Cat-III.

Providing & erecting 240 V MCB double pole switch for

lighting Load (B Curve) having 10 KA breaking capacity &

3 confirms to IS : 8828 in existing box having following 40.00 Each 278.76

(A) 6 to 32 Amp. Cat. III

Providing & erecting 415V MCB Four Pole Switch for

Lighting Load (B curve) having 10KA breaking capacity &

confirms to IS :8828 in existing box having following

capacity. (b) 40 Amp

Providing and erecting HOT deep Galvanised iron strip

wire 8 to 16 SWG.

Providing and erecting Pipe type earthing with 40 mm dia

2.5 mtr long 'B' grade G.I. pipe with necessary coupling

6 buch buried in specially prepared earth pit & G.I. earth 40.00 Each 823.15

wire of 8 SWG erected & connected as directed (For panel)

For using salt and charcoal / coke as required for pipe type

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured

cable multistrand Aluminium conductor for 1.1 KV. to be

laid on wall with necessary clamps or in existing trench /

pipe of following size of cables (c) 4 core 10 Sq. mm

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured

cable multistrand Aluminium conductor for 1.1 KV. to be

laid on wall with necessary clamps or in existing trench /

pipe of following size of cables. (C) 4 Core 35 Sq.mm

Supplying following size of Light duty “A” Class G.I . Pipe

10 & erecting as directed by Engineer-in-charge. (A) 25mm 120.00 Meter 172.71

Providing & laying approved make Double walled

corrugated pipes (DWC) of polyethylene(conforming to IS

14930 II) with necessary connecting accessories of same

material at required depth in existing trench for laying of

cable. below ground / road surface for enclosing cable (A)

Providing and, fixing heavy duty flange type brass cable

gland with rubber ring for PVC insulated armoured cable

complete with out going tails, insulating tape etc for

following size of cables. (C) 2 to 4 core 10 Sq. mm

Solder less crimping type Aluminium lugs conforming to IS

suitable for cable of following size evenly crimped with

13 high pressure tool & connected to switchgear terminals 160.00 Each 13.13

with brass/cadmium plated nut bolts in an approved

manner. (B) 10 Sq.mm

Supplying Steel tubular pole (Swaged) confirming to IS -

2713 (Part-II) 1980. Manufacturing process of steel

tubular pole should be as per IS specification. Basic steel

tube should be ISI Marked. Pole should be painted by one

coat of Zinc comet Primer and two coat of Aluminium

/approved paint to be erected on / in existing Foundation.

The length of poles are as below.

(A) 7.50 mtr. Long Swaged Steel tubular pole

(i) Pole as per IS code 410-SP-4 with 300 x 300 x 4 mm

base plate. (Approximate weight 78 Kg) For burial

(ii) Add Extra for M.S. Base plate 300 x 300 x 16 mm for

pole, mounting on surface of foundation on foundation

bolt with required stiffeners.

Providing 1:2:4 cement concrete foundation & 70 % PCC

from bottom including excavation for the pole of size 60 x

60 x 120 cm. Deep in below ground level with plinth of

cm x 45 cm(or 45 cm dia x 45 cm) high upper ground level

with necessary curing and finishing in approved manner. (

for 7.5 & 8/8.5 mtr pole)

Supplying & erecting approved make SMC press moulded

composite FRP. loop-in, loop-out approx. 2mm thick box

complete with Bakelite connector strip

5way(3P+N+E),DIN rail for mounting mob & hinged doors

16 as per requirement having locking arrangements with 40.00 Each 476.72

mounting clamp with nuts, bolts & washers suitable for

erection on pole with cable clamps& earth bolt of

following size of box.

(c)150mm x 125mm x 100mm [deep]

Providing and erecting street light pole bracket

comprising main B Class MS pipe of 4.2 cm/require

outside dia. complete with suitable B Class M.S. sleeve

tubing of approx. 45cms.length and suitable for 76.5 mm /

80mm. / require size pole top having sufficient fasteners

17 for fixing the brackets and having spread of 1 mtr. length 40.00 Each 561.56

with suitable rise as per site condition & suitable welded

stiffener reducer and nipple with check nut complete

painted with one coat of Red oxide / PU base primer and

two coats of Aluminium / PU paint. paint with following

nos of arms. [A] Single Arm bracket 1 Mtr

Supplying & erecting IP 55 grade following size section

pillar fabricated from joint less M.S. Sheet with angle iron

legs made from jointless M.S. Angle with cable clamps to

be buried in ground to have appropriate erection to work

uniform until erected with cement concrete foundation

and 45 cm high bricks work finishing with plaster etc.

hinged double door internally supported on both side,

with internal and outside looking arrangement with look

18 and keys in duplicate 35 x 35 x 5 mm M.S. Angle of Two 1.00 Each 16,691.26

Nos. one is welded and other with nut and bolt for erecting

Bakelite sheet. Painting the Section Pillar inside and out

side with three tank powder coated paint. section pillar

roof should be without joint with water leakage proof &

tested as per IP 55 test & followed by IS 2147 of 1962 (A)

150 X 90 X 75 cm section pillar fabricated from 14 Gauge

MS Sheet with angle iron legs 95 cm long made from 40 X

40 X 6 mm thick MS angle.

Name of Work : Providing & fixing machinery For Dryt Waste Processing Plant For Karamsad Anand

Municipal Corporatrion.

Dry Waste Processing Plant – 100 TPD

Abstract Schedule-B2.10

Machine Name Description HP Amount

1 Feeder Platform Feeder Platform

Width-1000 mm X Length-12000 mm

2 Motor-10 HP 10

Flat Belt conveyor- extra support roller

more than 20 mm Width-800 mm X Length-6000 mm

3 material conveyer Motor-5 HP 5

Flat Belt conveyor

Bag Opener 2500 MM X 2500 MM

50 HP + 50 HP Motor

FeederConveyerf Width-1200 mm X Length-10000 mm

5 or Trommel of 20 Motor-7.5HP Trough Type 10

Trommel Screening- Dia-1800 mm X Length- 6000 mm Hole Dia- 20 mm

20 Motor-10 HP Full Cover

Less than 20 mm Width-1000 mm X Length-10000 mm

7 Product Conveyer Motor-7.5 HP Trough Type 7.5

Trommel screening- Dia-1500 mm X Length- 5000 mm Hole Dia- 6 mm

8 6 mm Motor-7.5HP 7.5

Less than 6 mm Width-800 mm X Length-7000 mm

Product Conveyer Motor-5 HP

9 Trough Type- Ready Trough type conveyor 5

More than 6 mm Width-800 mm X Length-6000 mm

Conveyer Trough Motor-3 HP

Type- Reject- 6-20 Trough type conveyor

BALLISTIC Ballistic Separator

SEPERATOR Length- X Width-

11 Fan- 2.0 HP- 1 Nos. 10

Main Motor-10 HP

Chutes for Fine,2D Fraction,3D Fraction

3D- C&D Waste, Width-1200 mm X Length-8 Meters

Heavy material, Motor-7.5 HP

Glass and PET Trough type conveyor

Bottles, Cans, Metal

Overbend magnetic Width-1000 mm X Length-5000

separator on more mm

13 than 20 mm Motor-7.5 HP 7.5

material conveyer Flat Belt conveyor

Segregation Width-1000 mm X Length-10000

Flat type conveyor

Baling Machine-100 Working Chamber- 800 mm X

15 Bale- 100-125 KG/ Bale 15

Motor- 10 HP, Havells

2D- Light, Width-1200 mm X Length-11

Polyethene, Meters

wrappers, cloth, Motor-7.5 HP

Paper Material Flat type conveyor

Fatka Machine- 15 Fatka Machine

HP Shell Dia-1200 mm

Shell Length- 2200 mm

Total Height- 2000 mm

Motor- 10 HP, Havells

Fine Material, Wet Width-1000 mm X Length-8 Meters

18 waste Conveyer Motor-5 HP 5

Trough type conveyor

19 Panel 250 HP

20 Installation

Toatl HP At Corporation Scope 144 HP

KARAMSAD-ANAND MUNICIPAL CORPORATION, ANAND,Dist:ANAND.

Name of Work : Name of Work : Development of treatment facilities for processing of construction

waste & demolition (C&D) waste AT Karamsad Anand Municipal Corporatrion.

Sr. No. Particulars Amount Rs.

Schedule-B3.1 Renovation Existing shed & Construction Road ₹

Schedule-B3.2 Electrification Shed ₹

Schedule-B3.3 Renovation Machinery at C & D Waste Processing Plant Etc. ₹

Name of Work : Renovation Existing shed & Road of C & D Weste Processing Plant at Decomposite Site,

AT Karamasad Anand Municipal Corporatrion.

Abstract of Schedule-B3.1

Description Qty Unit Amount

Brick work using common burnt clay building bricks

having crushing strength not less than 35 kg./Sq.Cm. in

foundation and plinth in Cement Mortar 1:6 (1- Cement :

6 -fine sand) Extra for brick work in superstructure above

plinth level upto floor two level (B) Conventional (upto

Providing 15mm thick cement plaster in single coat on

Rough (Similar)side of single or half brick walls for

interior plastering upto floor two level and finished even

and smooth in (i) Cement mortar 1:3 (1-cement:3-sand)

and finishing with a floating coat of neat cement slurry.

Finishing wall with weather proof exterior emulsion paint

on wall surface (two coats) to give an required shape

3 even shade after thoroughly brushing the surface to 420.00 Sqm 120.26

remove all dirt, and remains of loose powdered materials

Providing corrugated G.I. sheet of class-3 roofing fixed

with glavanished iron J or L Hooks, Bolts and nuts 8mm

diameter with bitumen and G.I. limpet washer or G.I.

limpet washer. filled with white lead complete excluding

the cost of purlins, Rafters and Trusses.(1) 0.80 mm thick

Steel work, welded in built up sections framed work

including cutting, hoisting, fixing in position and applying

a priming coat of red lead paint. (A)In beams and joists,

5 channels angles Tees, flats, with connecting plates or 245.00 Q. 9108.48

angle cleats as in main and cross beams. Hip and jack

rafters, purlins conneted to common rafters and the like

Clearing and grubbing road land including uprooting rank

vegetation grass bushes,shrubs,sapling and trees girth up

6 to 300 mm removal of stumps of trees cut earlier and 0.02 Hec 80243.79

disposal of unserviceable materials (A) By manual means

in area of light jungle

Box cutting the Road surface to proper slope and camber

for making a base of road work including removing the

excaveted stuff and dipositing on the road side slopes

directed upto 50 mtrs.lead.

Providing and laying compacted WBM of Grading-II

MCBT metal of size 45 to 63mm in required layers

including using 16% stone screening, 13.2mm size and

8% stone dust as filler including spreading watering &

consolidation by vibratory roller etc. comp.

Providing and laying cement concrete 1:3:6 (1-Cement : 3-

coarse sand : 6- hand broken stone aggregates

9 mmnominal size) and curing complete excluding cost of 33.80 Cum 3005.76

formwork in (A) Foundation and Plinth

Providing and laying controlled cement concrete M.250

and curing complete excluding the cost of formwork and

10 reinforcement for reinforced concrete work in (A) 345.00 Cum 4345.72

Foundations, footings, Base of columns and Mass concrete

Providing TMT Bar FE 500D reinforcement for R.C.C.

11 work including bending, binding and placing in position 13800.00 Cum 77.29

complete upto floor two level

Labour charges for laying R.C.C. floor of M-200 grade of

concrete (Trimix) to be concreted in alternate panels. The

panel shall be formed on four sides with M.S. channel

bolted in position for forming the size. The entire

concrete mass shall be vibrated with skirt vibrator so as

to bring out slurry on top and smooth finished integrally

as per instruction of Engineer in charge and as per

specification including applying "NITO FLOOR HARD

TOP" or equivalent (Fair create, sikka applied at the rate

of 4.5 kg/10 Sq.m on R.C.C. floor as per Manufacturer's

specification) after base concrete has stiffened to the

point when light foot traffic leaves an imprint of about

mm. Any bleed water should have evaporated including

fitting, joint cutting, filling bitumen curing etc. complete

as per instruction of site Engineer. Excluding steel &

including form work with all tools, plants, Machinery and

all cost of chemical required for Trimix concrete including

Groove Cutting 4 to 5 mm wide and 60mm Deep at every

Name of Work : Estimate of C & D Shed Electrical Work at Decomposite Site, AT Karamasad Anand Municipal

Abstract of Schedule-B3.2

Qty Item Total Rate Per Amount

Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of

sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC

insulated multi strand copper wires up to 10 mtr length , in

below type of pipe erected with 6A Modular type switch / bell

push & accessories and earth continuity of following type, erected on

PVC / Metallic/Wooden box, single mounting base frame covered

1 50.00 with textured/metallic/white front plate modules erected on / in 449.45 Pt

wall / ceiling as per pipe erected, with necessary Lamp holder/ceiling

rose / H.D.Connector as directed. (f) with medium class Rigid PVC

pipe and accessories erected concealed in wall/ceiling complete

Point wiring for FAN with 2-1.5 sq.mm & earth wire of

sq.mm (Green) both are of .ISI marked 1.1 KV Grade FRLS PVC

insulated multi strand copper wires up to 10 mtr length, in below type

of pipe erected with 6A Modular type switch and hum free EME step

type electronic fan regulator mounted and accessories with

earth continuity of following type erected on PVC / Metallic/Wooden

2 30.00 box, single mounting base frame covered with 629.23 Pt

textured/metallic/white front plate modules erected on / in wall /

ceiling as per pipe erected. with necessary ceiling rose /

H.D.Connector as directed. (f) with medium class Rigid PVC pipe

and accessories erected concealed in wall/ceiling complete CATIII

Point wiring for on board Looped Plug with 6A Modular type switch &

5 pin socket erected on PVC / Metallic/Wooden box, single

mounting base frame covered with textured / metallic/white

3 35.00 front plate modules erected on / in wall / ceiling with following 241.39 Pt

accessories Cat. III

Point wiring for Individual Plug with & earth wire of 1.5 sq.mm

(Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated

multi strand copper wires up to 10 mtr length, in below type of pipe

erected complete with Modular type switch & 5 pin Plug erected on

PVC / Metallic/Wooden box covered with appropriate front plate

modules erected on / in wall / ceiling as per pipe erected with

4 25.00 following type of accessories. [I] For 6A Plug and 6 a switch with 473.69 Pt

2-1.5 sq.mm Cu. Wire from nearby switchboard/mcb db board (f)

with medium class Rigid PVC pipe and accessories erected concealed

in wall/ceiling complete

Point wiring for Individual Plug with & earth wire of 1.5 sq.mm

(Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated

multi strand copper wires up to 10 mtr length, in below type of pipe

erected complete with Modular type switch & 5 pin Plug erected on

PVC / Metallic/Wooden box covered with appropriate front plate

modules erected on / in wall / ceiling as per pipe erected with

5 25.00 following type of accessories. [II] For 16A Plug and 16 amp switch 697.91 Pt

with 2-2.5 sq.mm Cu. Wire from mcb db board. (f) with medium class

Rigid PVC pipe and accessories erected concealed in wall/ceiling

Providing and erecting Sheet Steel powder coated MCB distribution

board - flush / surface mounted fitted with busbar, neutral link, earth

bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 &

without MCB to house appropriate nos. of MCBs.(The DBs should be

6 15.00 used of same company of MCB to be used) suitable for (A) 582.77 Ea.

single phase incoming and horizontal single phase outgoing (a) single

(IP-30) (ii) 6 way

providing and erecting Approved make RCCBs conforming to IS:

12640 and having sensitivity of 30 mA and Short Circuit

withstand capacity of 10 KA and suitable for operation on single

phase 240 V,50Hz. having characteristic of quick action & tripping

7 5.00 with all advance feature & do not incorporate any electronic 2235.13 Ea.

component. for following Max. rating erected as directed. (ii)

40Amps. DP, CAT - III

providing and erecting Miniature circuit breaker single pole 6A to

25A suitable to operate on 240 V A.C. system and having breaking

8 10.00 capacity 10 KA to be erected in existing box. confirming to IS 112.11 Ea.

8828/1996 with ISI Mark CAT - III

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable

Aluminium conductor for 1.1 KV. to be laid on wall with necessary

9 409.92 clamps or in existing trench / pipe of following size of cables. (B) 2 90.90 Rmt

Supplying & erecting energy saving Energy Efficient E+ (1 - 4 ft)

watt retrofit tube fitting with one no 28watt T-5 tube

complete with E.G.P. wings reflector / clear acrylic guard cover &

tube and electronic inbuilt circuit ballast of rating 130 to 325 V

10 25.00 A.C. The fittings should be able to fit in any conventional existing T - 8 493.89 Ea.

tube fittings complete erected in an approved manner. - Cat-III

Supply, Installation, Testing and Commissioning of suitable sweep,

BEE 5 Star rated, Ceiling fan with Brush Less Direct Current

(BLDC) permanent ferrite magnet Motor, class of insulation: B,

Rust free 3 nos.Aluminium blades, 2 nos. canopies, shackle kit

with earthing provision, copper winding, Power factor not < 0.9,

Service Value (CMM/W) minimum 6.85, Air delivery minimum

215 CMM, 350 RPM,230v (tolerance as per IS : 374-2019), THD <

11 10.00 10%, with remote unit for Speed Control and all remaining 2885.57 Ea.

accessories including safety pin, nut bolts, washers, temperature

rise = 75 degree C (Max.), suitable for 140 to 285 Voltage and

rectifier circuit with surge, over current and overload protection

50 Hz, Single phase AC Supply, earthing etc. Complete as

required.[ Make shall be approved by Engineer in Charge] (B)

Supplying and erecting 19 / 20 mm. nominal bore Medium

Class M.S. Pipe down rod erected duly painted for fan

complete with proper insulation without leakage and earthing.

Supplying & erecting approved make low noise decorative

exhaust fan having square frame ABS body with inbuilt lowers &

frame. 200mm with 1350RPM Cat.II

PVC snap- on adaptable trunking/Pop up Box with required

items erected with necessary connection. As desired by Engineer In

charge iii) Bell Push 6 A SP 1 Way cat-III

Supplying & erecting earth pit of minimum bore dia.150mm size

approved make Earthing Electrode consisting Pipe-in-Pipe

Technology as per IS 3043-1987 made of corrosion free hot dipped

G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron

galvanising, Inner pipe dia of 25 mm having 200-250 Micron

galvanising, connection terminal dia of 12mm with constant

ohmic value surrounded by highly conductive compound with high

charge dissipation suitable for following type of applications with

chamber and heavy duty cover. (A)(approved make OEM has to

submit test certificate including value of earth resistance of

installation duly stamped and signed by agency and officer

Incharge has to ensure the value of earthing resistane mentioned

15 10.00 in test Certificate) & having back filling compound of (B) 4591.46 No

Inner chemical (CCM Compound)- Resistivity:- 0.2 ohm / meter

testing as per IEC 62561- 2017, Voltage drop:- < 1 volt at no load &

dry form, Sulphar content:

<2%(C) Back fill Compound :- Earthing compound should be

capable to retain moisture for long time Necessary test report must

be submitted by Agency. (a) For Electrical Installation up to 440V in

normal soil Length of pipe - 1 Mtr Back filling compound - 1 Nos Bag

Supplying and erecting LED street light / Flood light fittings

with High power White LEDs wattage of 3 Watt and above

assembled on single MCPCB, efficiency more than 130 lm/w and

corrosion free High pressure die cast aluminum housing with

smooth finish powder coated and heat sink extruded

aluminium with diffuser and Polycarbonate optics/ lenses,

with toughened glass with company mark/name engraved or

embossed 160 to 270 V,Power Factor more than 0.95, THD <

10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45, Luminaire

efficacy> 100 lumens/watt . LED driver efficiency

16 20.00 > 85 %.( fittings required LM-79 & LM-80 certificates)(NOTE: Below 6566.01 No

description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity

between the ranges shown.) (A) Street Light (IP-65), Surge

protection -4KV integral and, Light must have 440VAC line supply

with over-voltage protection.(iv) Above 90 to 120 watts Cat-lll

Supplying and erecting B class galvanised iron pipe 32 mm outside

dia 45 cm long duly welded on 20 cm x 20 cm x 3 mm thick

17 10.00 M.S. base plate, erected on wall or corner for mounting street 343.40 No

light luminaire with necessary hardware materials duly painted.

Supplying and erecting Flexible PVC insulated multi strand multi core

1.1 kv grade ISI marked copper wires of following size to be erected

as directed. (e) 1.50 Sq.mm 3 core round PVC sheathed

Providing & laying approved make Double walled corrugated pipes

(DWC) of polyethylene(conforming to IS 14930 II )with necessary

connecting accessories of same material at required depth in

existing trench for laying of cable. below ground / road surface for

enclosing cable (A)50 mm outer dia

Providing following type of Modular Type Accessories mounted with

PVC / metallic/Wooden box, single mounting base frame covered

with textured / metallic/white front plate , modules erected with

necessary connections as per site situation directed by Engineer

20 10.00 In charge. (13) 6A/10A/16A/20A/25A/32A Single pole Modular 295.93 Pt

Name of Work : Renovation machinery At C & D Weste Processing Plant at Decomposite Site, AT

Karamasad Anand Municipal Corporatrion.

Abstract of Schedule-B3.3

Description Qty Unit Amount

Providing & Fixing Machinery at C & D Waste Processing

Plant Etc Complete.

Procurement of Frount end loader (1.0 Cum

I/We am/ are willing to carry out the work @ _____________ % Above /Below ____________ Percentage (Should be

written in Figures and Words) of the Estimated rates mentioned above amount of my/ our Tender work out as

Estimated Amount Estimated Amount

Total Rs. 20,39,25,369.00 Total Rs.

Deduct % Add % Rs.

Total Rs. Total Rs.

(In ward (In ward

1. The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-In-

Charge for which no extra payment shall be made

2. The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3. GST and Income tax TDS will be deducted at a source while making payments of bills

In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-10/2017

Cement Consumption/16/C

4. Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where there is a change as per actual mix design the

cost of difference of cement consumption have been deducted from the rate of original item at the rate of input rate

mentioned in all the tender.

Stamp with signature of contractor Deputy Executive Engineer

Karamsad Anand Municipal Corporation