Annual Plan 2022-23, SO335/23 Allama Iqbal smaraka Library and Reading room Interior work in ward no.37 at Tirur municipality

Amount

Library Interior

15.7.4:Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.In cement mortar

15.12.1:Dismantling doors, windows and clerestory windows (steel or wood ) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead:Of area 3 sq. metres and below

OD302185/2022-2023:Engaging coolie

50.6.1.8:Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x15cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level with thickness 15cm in: CM 1:6 ( 1 cement : 6 coarse sand etc complete

13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

21.1.1.2:Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately): For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

21.1.2.2:For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron)

21.3.1:Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness

14.75:Repair to plaster of thickness 12mm to 20 mm in patches of area 2.5 sqm and under, including cutting the patch in proper shape, raking out joints and preparing plastering the wall surface with white cement based polymer modified self curing mortar, including disposal of rubbish, all complete as per the direction of Engineer-In-Charge.

12.45.3:Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with:12.5 mm thick tapered edge gypsum moisture resistant board

9.48.2:Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ wooden frames with rawl plugs screws etc

OD314429/2022-2023: Storage With Veneer Finish: Supply and placing storage (45 cm depth)as per design intent. Framework to be finished using 19 mm thick Plywood ( IS 303 grade ,Greenply /equivalent) & 9 mm ply ( IS 303 grade ,Greenply /equivalent) to be fixed on back side of storage . Outer portion of the storage to be finished with 4 mm thick melamine polish finished veneer (Greenply/equivalent) as shown in drawing.Inner portion of the storage to be finished with 1 coat Primer & 2 coat enamel .Back side of the storage to be finished with one coat Primer.Use necessary SS hinges, .SS handles, Locks, etc (Make: Hettich/Ebco/equivalent).Finish as per drawing with necessary grooves & electrical openings if any.Including cost and conveyance of all materials labour charges etc.(Elevation area will be measured)

OD314430/2022-2023: Zebra Blinds : Providing and fixing manual Controlled Curtains/Blinds made of premium quality fabric around aluminium tube to be raised and lowered by ball chain pulley, to provide adequate privacy and light control. as per architect approved shade (Make :Xera SG(Korean made)/Equivalent ) .Including cost and conveyance of all materials labour charges etc.

OD314431/2022-2023:Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (including Handle, bottom lock,stopper and frosted film)

OD321022/2022-2023: Veneer Paneling:Providing and fixing panelling(up to 2600 mm height or as per design intent) as per approved drawing. Framework finished with 19 mm thick plywood (ISI 303 grade , Greenply/Equivalent), i.e. 50 mm sections to fixed at 600 mm c-c spacing/as per site condition .Exposed side of the frame to be fixed with 9 mm plywood (ISI 303 grade , Greenply/Equivalent).Finish the panelling with 4 mm thick melamine finished veneer sheet ( Greenply /Equivalent,) fixed on to the plywood using suitable adhesive(HeatX/Equivalent). Finish the panelling with necessary grooves, electrical / window openings if any. Including cost and conveyance charges of all materials, labour charges etc.

14.43:Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

13.43.1:Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.80:Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

13.60.1:Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work

14.54.1:Painting with synthetic enamel paint of approved brand and manufacture of required colour to an give even shade:One or more coats on old work

OD321019/2022-2023:Supplying and fixing Vinyl print name board including all cost and labour charges etc complete

k.SIDDHIQUE

MOHANDAS P

Bidder Name

MOHANDAS P

k.SIDDHIQUE

YASIR AHAMED N