Repair to joinery, aluminium window doors, PVC doors and sanitary plumbing fitting at Arty Bde Stn HQ, Fd Regts, ALG, DKG, CWE Rajouri FSD and GE 862 EWS of AGE BR Dett-III under GE 862 EWS

Amount

Dismantling of timber scantling 40 Sqcm and over in section, in any position as in unframed or framed work complete all as specified and directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed.

M&L for rolled section as in main and cross beam / columns, hip and jack, rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates (Fe-410 Gde E-250 Quality A) complete all as specified and directed. (Note :- All structural steel work shall be painted with one shop coat of zinc chromate red oxide primer including preparation of surfaces before fabrication and rate shall be included in this item).

Dismantling of asbestos cement (corrugated, semi corrugated etc) sheeting in roof covering, complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nanital or similar pattern roof coverings, complete all as specified and directed.

S&F for Pre-painted galvalume aluminium zinc coating GI based corrugated sheet 0.50mm thick of approved colour having tensile strength 550 MPa as in roof covering/ cladding to wall fixed with self tapping screws including side and end lap as per manufacturer’s instructions, complete all as specified and directed.

S&F for Pre-painted galvalume aluminium zinc coating GI based plain sheet 0.50mm thick of approved colour having tensile strength 550 MPa as in ridges, hips, valley gutters fixed with self tapping screws including side and end lap as per manufacturer’s instructions, complete all as specified and directed.

Taking down chowkhats or frames (without taking off shutters from the frames) n.exc 1.5 Sqm each and removing from site, complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area exceeding 1.50 Sqm and not exceeding 4.0 Sqm each removing form site, complete all as specified and directed.

Taking down shutter of any description exceeding 1.0 Sqm but not exceeding 2.0 Sqm, complete all as specified and directed.

S&F for pressed steel door frame of size 125x60 mm with one or more rebates incl necessary fixing lugs, hinges, lock and strike plate etc including back filling to chowkhats in PCC 1:3:6 type C-0 using 12.5mm graded stone agregate, complete all as specified and directed.

S&F for pressed steel frame for doors with one or more rebates of size 105x60mm including necessary fixing lugs, hinges, lock and strike plate etc including back filling of chowkhats with PCC 1:3:6 type C-0 using 12.5mm graded stone agregate, complete all as specified and directed.

S&F for factory made 2nd class hard wood 35 mm thick plain framed panelled shutters (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part-I), kiln seasoned and chemically pressure treated, complete all as specified and directed.

S&F for factory made 30mm flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as specified and directed

S&F for factory made 35 mm thick 2nd class hard wood glazed and skelton shutters open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkhats, complete all as specified and directed.

M&L for solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square, complete all as specified and directed.

S&F for factory made solid panel PVC moulded door shutter 28 to 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail : Panelling of plain colour PVC sheet to be fitted in the M. S . frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing mentioned in SSR Part-II 2020, complete all as specified and directed.

S&F for anodised aluminium, powder coated (minimum thickness of power coating 50 micron) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc, complete all as specified and directed.

M&L for powder coated aluminium (minimum thickness of powder coating 50 Mircon) anodized aluminium for shutters of doors, window & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (fittings shall be paid for separately) with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS 733 and IS 1285, fixinfg with dash fasteners of required dia and size, including necessary filling up the gaps at junctions i.e at top, bottom and sides with required EPDM rubber / neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever requried including cleat angle, aluminium snap beading for galzing / paneling CP brass/ stainless steel screws all complete as per architectural drawings, complete all as specified and directed by Engr -in-Charge.

S&F for 100mm long butt hinges medium weight cold rolled stainless steel (ISI Marked) , complete all as specified and directed.

S&F for 75 mm size mortice lock of brass, vertical type, 4 levers, complete all as specified and directed.

S&F for door closer hydraulically regulated, aluminium (extruded section body) designation No 2, universal type, suitable for door shutters of 701 to 850mm in width and of weight between 36 to 60 Kg (ISI Marked), complete all as specified and directed.

S&F for extruded aluminium alloy handles size 200 mm fabricated type anodised (ISI marked), complete all as specified and directed.

S&F for Powder coated anodised aluminium window and ventilator shutters, (minimum thickness of powder coating 50 micron) side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no) hinges type B-21 100mm long (2 no) suitable handle (1 no), complete all as specified and directed

S&F for Powder coated aluminum anodized three track slinding window with two or more shutter with 4 mm thick plane glass, one shutter of stainless steel mosquito proofing with good quality bearing, handle lock, etc including 65 X 39.5 X 1.5 mm section for complete frame and rubber beading and glazing clips etc using following sections as given in 'JINDAL' catlogue including taking down existing old window of any description complete as specified and directed by Engr-in-Charge. (Note :- Minimum thickness of powder coating not less than 50 micron).

S&F for Powder coated aluminium anodized grills 10.00mm dia decorative type 75mm mesh size, complete all as specified and directed.

S&F for steel windows (box type) factory made double shutter (glazed and wire gauzed) with side hung shutters including pintle type hinges, steel handles fabricated type for each duly welded, mild steel barrel tower bolts 150mm size (02 Nos for each leaf) duly welded, complete with galzing bars, including guardbar of 12mm square bar dovetailed or welded inlcuding MS fillet including one shop coat of red oxide primer over window frame & guard bars complete all as specified and directed. Note: Glass & wire gauge shall be measured and paid separetly.

M&L for steel ventilators with top hung shutters openable type including hinges and handle with steel peg stay complete without glazing bars, dovetailed or welded, complete all as specified and directed.

S&F for sheet glass 5.5 mm thick, ordinary quality and fixed with aluminum & rubber beading in square exc 0.5 sqm in each pane, complete all as specified and directed.

M&L for 12mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed to aluminium door or similar work, complete all as specified and directed.

S&F for plain ACP board 5mm thick, fixed in aluminium door or similar works joinery including cutting, packing, finishing, complete all as specified and directed.

M&L in repair for framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290, Gde E-165, complete all as specified and directed.

S&F in repair 100mm long butt hinges medium weight cold rolled mild steel (ISI Marked) , complete all as specified and directed.

S&F in repair for 75 mm size mortice lock of brass, vertical type, 4 levers fixed to aluminium doors, complete all as specified and directed.

S&F in repair for door closer hydraulically regulated, aluminium (extruded section body) designation No 3, universal type, suitable for door shutters of 701 to 850mm in width and of weight between 36 to 60 Kg., Complete all as specified and directed.

S&F in repair for double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed, (ISI marked), complete all as specified and directed.

M&L for 300mm long (length of bolt) aluminium alloy, anodised, sliding door bolt with hasp, stapl (bolt type) and fixing clips of sheets, cast or extruded section and fixing bolts and sliding bolt of extruced sections or cast aluminium alloy anodised (ISI marked), complete all as specified and directed.

S&F for 250 mm long mild steel sliding door bolt plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate (ISI Marked), complete all as specified and directed.

M&L for 300mm long brass sliding door bolt with de-cast brasshasp, staple, bolt type 10-12mm dia decorative type, fixing with rolled or drawn brass botls to wooden / PVC / FRP doors shutters, (ISI marked), complete all as specified and directed

S&F for extruded aluminium alloy handles size 125 mm fabricated type anodised (ISI marked), complete all as specified and directed.

S&F for aluminium anodized barrel tower bolts 150 mm long of extruded section (ISI marked) ,complete all as specified and directed.

S&F for 4 mm thick sheet glass ordinary quality and glazing with oil putty in squares n . exc 0.50 sqm in each pane, complete all as specified and directed.

S&F for 3 mm thick figured glass pin headed type and glazing with oil putty in squares n . exc 0.50 sqm in each pane complete after hacking out old broken glass all as specified and directed.

S& F for galvinsed mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperature 1.18mm and fixed with stainless steel wire staples, complete all as specified and directed.

S& F in repair for stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperature 1.40mm and fixed with tinned tacks, or galvinsed wire staples , complete all as specified and directed.

S& F in repair for galvinsed mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperature 1.18mm and fixed with stainless steel wire staples, complete all as specified and directed.

M&L for preparation of new wooden surfaces of any description exc 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

M&L for preparation new of previously untreated steel or iron surface or roof sheet or windows of any description over 10cm width or girth not otherwise described and applying two coats of sybthetic enamel paint, complete all as specified and directed.

M&L in repair for 18 / 19mm thick prelaminated particle board, cupboard, kitchen cabinat shutter etc, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with screws to timber frame work, complete all as specified and directed.

S&F 140mm long floor door stopper of aluminium alloy anodised body and tongue with hard drawn steel spring, complete all as specified.

S&F in repair for fancy type mild steel curtain rod powder coated 20mm dia (colour and design approved by Engr-in-Charge), complete all as specified and directed.

S&F in repair for bracket of fancy type (colour and design approved by Engr-in-Cgarge, curtain rod powder coated 20mm dia including fixing to walls with MS full screws (including fixing of wooden pieces of required size of walls), complete all as specified and directed .

S&F in repair for stainless steel curtain rod of 20mm dia with 'T' and 'L' type brackets etc, complete all as specified and directed.

M&L in repair for door bottom sealing strip guard with double sided insulation for doors, which are equally able to keep wind, dust and sound or poluted air out side of door (i.e. Anti Lizard strip), complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and paving n exc 15 cm thickness below or above the ground level including dismataling old tile, complete all as specified and directed.

M&L for 75mm plain cement concrete 1:4:8, type D-2 (using 40mm graded crushed stone aggregates) as in sub base for tiling, complete all as specified and directed.

M&L for vitrified tiles light shade (premium quality) 10 mm thick (square/ rectangular) polished, area of each tiles n exc 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface, laid over and including 15 mm thick screed bed in cement mortar 1:4 after dismantling old unserviceable of tiles, complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (premium quality) Square/rectangular, area of each tile exceeding 0.11 sqm but n.exc 0.18 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over and including 15mm thick screed bed in cement mortar 1:4, complete all as specified and as directed.

M&L for glazed ceramic coloured tiles of size 450 x 350 x 7mm thick, (premium quality) on vertical surface of wall such as dado, skirting, riser etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over and including 10mm thick rendering in cement mortar 1:3, after dismantling old unserviceable of tiles, complete all as specified and as directed.

Taking down cement plaster, any description on any walls etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Demolition of brickwork or stone / boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone-work and precast concrete articles, complete all as specified and directed.

M&L for brick work with sub class ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6, complete all as specified and directed.

Description all as per srl item No. 62 above but except bricks NOTE: Old brick retrieved from demolition shall be used.

M&L for brick work using old size bricks sub class 'B', straight or curved on plan to any radius in half brick thick wall, built in cement mortar 1:4, complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1:6 on fair faces of brick or concrete work, finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of distemper oil emulsion over a coat of chalk whitening, complete all as specified and directed.

S&F for PVC (SWR) pipes single socketed in any length with rubber ring joints , fixed to wall of dia of bore 75 mm type 'B' complete after dismantling of old unserviceble PVC pipe all as specified and directed.

S&F for PVC (SWR) pipes single socketed in any length with rubber ring joints , laid in trenchs or in floor of dia of bore 110 mm type 'B' complete after dismantling of old unserviceble PVC pipe all as specified and directed.

S&F in repair 110 mm bore PVC (SWR) bend any radius with access door, complete all as specifed and directed by Engr-in-Charge.

S&F in repair 75 mm bore PVC (SWR) bend any radius with access door, complete all as specifed and directed by Engr-in-Charge.

S&F in repair for vitreous China wash basin, white, flat back, size 550x 400mm including 15mm bore pillar tap cast copper alloy, PVC connection 15mm length 450mm, low density PVC waste pipe, complete all as specified and directed.

M&L for 15 mm bore galvanized iron GI tubing medium grade with all fittings such as bends, socket, tee, elbow, union, nipple, short pieces and fixed to walls, ceilings or laid in floors after taking down GI tubing 15 mm bore and connections including taking down existing pipe, complete all as specifed and directed.

M&L for 20 mm bore galvanized iron GI tubing medium grade with all fittings such as bends, socket, tee, elbow, union, nipple, short pieces and fixed to walls, ceilings or laid in floors after taking down GI tubing 20 mm bore and connections including taking down existing pipe, complete all as specifed and directed.

S&F in repair for viterous china wash down water closet pan, white (pedestal pattern) and connection to single symphonic acion type including PVC flushing cistern 10 ltr capacity and fixed in floor with brass screw, plastic water closet seat, black/white, closed pattern with recessed bottom and cover and mild steel chromium plated or aluminised hinging device, with PVC pipe of superior quality, complete all as specified and directed.

S&F for in repair vitreous china urinals, half stall type aqua seal premium guality including flush pipe or PVC waste pipe and outlet, complete all as specified and directed.

S&F in repair viterous China water closet pedestal pattern in one piece type of dimention 73cmX36cm74cm including seat cover, floor mounted, 'P' or 'S' trap, flushing kit, CP jet with PVC pipe of superior quality and all necessary fixing arrangements, complete all as specified and as directed.

S&F for in repair sink with draining board made out of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, complete all as specified and directed.

S&F in repair brass cromium plated mixer for mixing hot and cold water for wash hand basin of 15mm dia screwed down for iron pipe, complete all as specified and directed.

S&F in repair for 15mm bore brass chromium plated sink mixer for mixing hot & cold water screwed down for iron pipe and fixed, complete all as specified and directed.

S&F in repair for wall mixer 3 in 1 with arrangement to overhead shower with connection legs wall flanges and wall bracket, complete all as specified and directed by Engr-in-Charge.

S&F for overhead PVC water tank cover threaded or plug type suitable for tanks of 500 / 1000 ltr capacity, complete all as specified and directed.

S&F in repair 15mm CP brass health faucet (hand shower) inlet length 100mm fixed to angle valve with and including decorative choice flexible pipe, wall hanger etc, complete all as speicified and directed.

S&F in repair for copper alloy chromium plated jet spray suitable for padestal pattern WCs including decorative choice flexible pipe fixed to iron pipe with and inclduing cover plate, complete all as specified and directed.

S&F in repair for plastic water closet seat cover black/white colour close pattern with flat bottom and cover and mild steel chromium plated aluminum hinging device for pedestal pattern WC, complete all as specified and directed.

S&F in repair for brass chromium plated shower rose 125mm with or without swivel joints, any size inlcuding fixing to steel pipe or union, complete all as specified and directed.

S&F in repair for PVC waste pipe 32mm long suitable for wash hand basins and urinals including connecting, complete all as specified and directed.

S&F in repair for PVC waste pipe 40mm long suitable for wash hand basins and urinals including connecting, complete all as specified and directed.

S&F in repair for assembled ready to use rectangular stainless steel (Grade 304) kitchen plate rack with 3-4 shelves, enclosed four sides by SS plain sheet, 0.6 mm squre support pipes, dedicated holes for spoon, pegs etc cover all size 900mmx750mmx250mm of standard pattern, complete all as specified and directed.

S&F in repair for glass corner self with tempered glass, stainless steel brackets and polished chrome finish rail , complete all as specified and directed by Engr-in-Charge.

S&F in repair for sheet glass shelf assembly consisting 5.5 mm thick, sheet glass shelf 12cm wide with chromium plated bracket guard and rainling 60cm long, complete all as specified and directed.

S&F in repair for 15mm bore concealed type Stop valve, cast copper alloy chromium plated screwed down, high pressure with crutch or butterfly handle, chromium plated, screwed both ends for iron pipe or for unions and fixed, complete all as specified and directed.

S&F in repair for 15mm bore bib tap cast copper alloy, chromium plated, with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair for 15mm bore Angle valve, cast copper alloy, fency type, chromium plated suitable for iron pipe and one end and PVC connector on other, complete all as specified and directed.

M&L in repair for 15mm bore gun metal, gate/globe valve with iron wheel head screwed on both sides for iron pipes, complete all as specified and directed.

M&L in repair for 20mm bore gun metal, gate/globe valve with iron wheel head screwed on both sides for iron pipes, complete all as specified and directed.

S&F for brass chromium plated tubular towel rail 20 mm dia "D" type 60 cm long between flange aluminium anodised complete as in repair all as specifed and directed.

S&F in repair brass cromium plated soap dish including cromium plated brass screws and wooden cleats, complete all as specified and directed by Engr-in-Charge.

S&f in repair for CP grating suitable for 75/100 mm bore floor trap and fixed with white cement complete, all as specified and directed.

S&F in repair for 15mm bore, pillar cock, cast copper alloy, with capstan heads, chromium plated, fency type, screwd down high pressure , with or without lettered hot or cold with long screwed shanks and fly-nuts, screwed for iron pipe and fixed, complete all as specified and directed.

S&F in repair for 10 ltrs capacity (PVC), valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, complete all as specified and directed.

S&F repair for PVC connection 15 mm x 600 mm including PTMT nuts at both ends screwed for iron pipe of 15 mm bore, complete all as specified and directed.

S&F repair for PVC connection 15 mm x 450 mm including PTMT nuts at both ends screwed for iron pipe of 15 mm bore, complete all as specified and directed.

S&F in repair for ball valves suitable for 15mm bore iron pipe high pressure of PTMT with epoxy coated aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 210 gms) complete all as specified and directed by Engr-in-Charge.

S&F in repair for ball valves suitable for 20mm bore iron pipe high pressure of PTMT with epoxy coated aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 210 gms) complete all as specified and directed by Engr-in-Charge.

S&F in repair for rotational moulded polythylene water storage tank (ISI marked) with float valve, plastic lid cover, multy-layered, cylindrical vertical with closed top, hoisted and fixed in position of capacity 500 ltrs tank and making connections inlcuding suitable GI wash out, over flow, nipple and including 15mm bore ball brass valve with union screwed for iron pipe and fixed after dismantling of old unserviceable tank , complete all as specifed and directed.

S&F in repair for rotational moulded polythylene water storage tank (ISI marked) with float valve, plastic lid cover, multy-layered, cylindrical vertical with closed top, hoisted and fixed in position of capacity 1000 ltrs tank and making connections inlcuding suitable GI wash out, over flow, nipple andincluding 15mm bore ball brass valve with union screwed for iron pipe and fixed after dismantling of old unserviceable tank, complete all as specifed and directed.

S&F for 4mm thick designer ceiling board in ceiling fixed with screw as per manufacturers instructions, laid over and including hot dipped galvanised iron in post grid with 24mm wide T section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33 mm thick galvanised steel sheet of size 24 x 32 x 300 mm spaced at 1200 mm centres securely fixed to the structural soffits by approved hangers at 1200mm maximum centres. Hangers of GI wire 4 mm dia to be fixed by approved rawl plug or hanged with existing truss members. The last hanger at the end of each main runner shall not be greater than 450 mm from adjacent wall flush fittings of 1200 mm long screws Tee with (double stiching) to interlocked between main runners at 600 mm centre to centre from 1200 x 600 mm modules cross tee longer than 600 mm modules to be formed by fittings 600 mm long cross tee, tee perimeter wall angle shall be of 0.45 mm thick galvanised steel of size 19 x 19 mm and 300 mm long of white colour all as per insturctions including dismantling of existing board etc, complete all as specified and directed.

Complete removal of existing water proofing treatment over RCC roof, projections of any thickness, any type by stripping out old tar felt over roofs, parapets, chimney stacks etc laid horizontally or vertically including taking out layer of cement plaster etc and cleaning the surface with wire brush including removing debris from the site and depositing in low lying area where directed and providing following :- (a) Rendering 10mm thick in cement mortar 1:3 on concrete roof surfaces and finish the surface even and smooth without using extra cement including mixing water proofing compound @ 2% by weight of cement. (b) Apply a coat of bituminous primer confirming to IS-3384@ 0.4 ltr/Sqm on newly plastered surface after curing as per IS-456 and dried. (c) After the primed surface has dried, apply a coat of hot blown bitumen(85/25 penetration) confirming to IS-702 @ 1.2 Kg/Sqm of the surface. (d) Provide polymeric water proofing membrane ISI marked laid with overlaps, bonded with hot blown bitumen, and laid by torch application method, end overlaps shall not be less than 150mm and side lap 75mm. Polymeric water proofing membrane should be five layered with centre core as 90 micron high molecular high density polyethylene film, min weight 3 Kg per sqm & minimum 3mm thick reinforced with polyster non wove fabric, APP membrane shall laid acorss the slop from lowest line of sloping roof towards ridge. (e) Over the APP membrane, apply a coat of semi hot blown 85/25 penetration grade bitumen confirming to IS-702 @ 1.20 Kg/ sqm and blinded with fine sand in dry condition @ 0.50 Kg / Sqm dusted over the bitumen coat Note : (i) Care shall be taken to avoid wrinkle and air gaps while sticking membrane to the bitumen applied surface. (ii) Ponding test shall be conducted for 72 hrs as directed. (iii) Rate of PCC leveling course and WPC shall be included in the quoted rate.

Taking out aluminium shutters of size not exc 2.00 Sqm each and refixing in the same opening after carry out any repair required complete all as directed. Note :- supply only parts replaced shall be measured and paid separately, complete all as specified and directed.

Taking out aluminium door, window frame size exc 2.00 Sqm each and refixing in the same opening after carry out any repair required complete all as directed. Note :- supply only parts replaced shall be measured and paid separately, complete all as specified and directed.

NATIONAL TRADING COMPANY

VIJAY KUMAR SURI AND SONS