SPL REPAIPR TO BLDG NO T-05 (B COY) AND BLDG NO-37 (RATION STORES AND WASHROOM SHOP) AT HASIMARA MIL STN UNDER GE (S) BINNAGURI

Amount

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and removal off the site.

Dismantling timber scantlings 40 sqcm and over in section as in framed work in any position complete all as specified and removal off the site.

Dismantling of wall and ceiling Boards(Fiber,pulp, Insulation etc) or insulation Board/slab/blankets any Thinkness including cover fillets complete all asspecified and removal off the site.

Demolition of reed, lathing, single or double, including battens and plaster or chicken wire lathing complete all as specified and removal off the site.

Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and removal off the site.

Taking down chowkats or frames not exc 1.5 Sqm each with shutters ( with out taking off shutters from the frames) complete all as specified and removal off the site.

Taking down chowkats or frames exc 1.5 sqm but not exc 4.0 Sqm each with shutters ( with out taking off shutters from the frames) complete all as specified and removal off the site.

M&L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified.

M&L fly ash Brick work using modular size bricks with sub class 'B' bricks curved on plan with mean radius not exc 6m with bricks roughly cut to radius or bricks with wedge shaped joints built in cement mortar 1:4 complete all as specified.

M&L for RCC (nominal mix) 1:1½:3 type A1 using 20 mm graded stone aggregate as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc, basement slabs, under reamed piles and mass concrete complete all as specified and directed . Note - Reinforcement and form work shall be measured and paid separately.

Use and waste of form work to sides of concrete foundation ,footings, bases of columns, raft and raft beams sides and soffits (if any )of foundation and plinth beams for flat rough finished concrete surface complete all as specified.

M&L for RCC (nominal mix) 1:1½:3 type A1 using 20 mm graded stone aggregate as in beam, cantilevers, bressummers, lintels over 1.5 m span and similar work complete all as specified. Note - Reinforcement and form work shall be measured and paid separately.

Form work to sides and soffits of floor or roof beam, beam hauchings, girders, bressummers, lintels, cantilevers, shelves, for flat rough finished concrete surfaces complete all as specified.

M&L for RCC (nominal mix) 1:1½:3 type A1 using 20 mm graded stone aggregate as in chajjas and similar work complete all as specified. Note - Reinforcement and form work shall be measured and paid separately.

Use and waste of Form work to chullah hood, chajjas, troughs and similar items including edges etc for rough finished flat concrete surface complete all as specified.

Mild Steel TMT bar 10mm dia and over cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

Mild Steel TMT bar 6 to 8 mm dia cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

Mild Steel TMT bar 5mm dia and over upto and including 10mm dia as in stirrups, spacers & binders cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

M&L for external rendering 20 mm thick in two layer, first layer shall be of 10 mm thick CM 1:6 and second layer of finishing coat shall be 10 mm thick in CM 1:4 mixed with WPC as per manufacturur's specification and as specified on brick work or concrete surfaces of wall and finished even and fair complete all as specified. Note-WPC shall be measured and paid seperately.

Supply only integral water proofing compound all as specified.

M&L for rendering 10 mm thick in CM 1:6 on fair faces of brick or concrete surface of wall and finished even and smooth with out using extra cement complete all as specified.

S&F steel work in tubular Square/rectangular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St -240 and painted one shop coat of zinc chromate primer paint including preparation of surface at contractor workshop before fabrication complete all as specified.

S&F MS steel Hollow section Square/rectangular as in roof truss ,purlin,rail etc etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St -240 and painted one shop coat of zinc chromate primer paint including preparation of surface at contractor workshop before fabrication complete all as specified.

S&F rolled mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes ,without and attachment of grade Fe 410-W (Gde E-250) quality A complete all as specified.

S&F Mild steel bolts. purpose made. with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut. Exc 30cm long complete all as specified and directed

S&F Rolled mild steel in Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) of grade Fe 410-W (Gde E-250) quality A complete all as specified.

S & F pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength 550 Mpa as in roof covering/cladding/ eaves board fixed with selp tapping screw complete all as specified.

Supply and fix 0.50mm thick prepainted galvalume polyester coated (SMP coating) coloured metal roofing sheet trapezoidal profile having tensile strength 550Mpa in roof and ridges fixed with self drilling screws with EPDM washer etc complete all as specified.

Supply and fixing aluminium anodised snap grid false ceiling to support the boards / tiles with aluminium Tee section 35 mm x 25 mm x 1.40 mm cross Tee 23.50 mm x 23.50 mm x 1.40 mm and aluminium angle 25 mm x 25 mm x 1.40 mm as on edge / sides including hanging proper hanging arrangement with 4 mm dia anodized galvanised iron wire and adjuster complete as specified.

Supply & fix 4 mm thick E-board designer building board (non asbestos) 605mm x 605mm in size fixed as on ceiling all as specified.

Demolition of cement concrete un reinforced in ground floor and paving n exc 15cm thick (below or above ground level) complete all as specified and removal off the site.

M&L for 100 mm thick Cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base complete all as specified.

M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in floor finishes 40 mm thick laid in panels & finished even and smooth without using extra cement complete all as specified.Note- Glass dividing strips shall be measured & paid separately as supply only.

M&L for non skid ceramic coloured tiles of design as approved by GE 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed in cement mortor 1:6 complete all as specified.

M&L for non skid ceramic coloured tiles of design as approved by GE 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in vertical surface /skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including rendering 10 mm thick in cement mortor 1:4 complete all as specified.

S&F pressed steel frames of size 125 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc including one shop coat of priming complete all as specified.

M&L for PCC 1:3:6 type C-0 (using 12.5mm graded aggregate) as in hold fast block including necessary form work etc complete all as specified.

S&F 35 mm thick second class hard wood rail and style plain framed factory made panelled shutter (two panel) with lock rail and panel of 9 mm BWP commerical ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (part-I), kiln seasoned and chemically pressure treated complete all as specified.

M&L Second class hard wood 30 mm thick factory made glazed and skeleton shutters, open rebated and prepared to receive glass , gauze etc with out sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in SSR part I section 8 clause 8.20 (a) complete all as specified.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified.

S&F Butt hinges, medium weight, cold rolled mild steel 75 mm long complete all as specified.

S&F mild steel barrel tower bolts stove enamelled black with bright bolt 125 mm long complete all as specified.

S&F mild steel barrel tower bolts stove enamelled black with bright bolt 150 mm long complete all as specified.

S&F mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate of 250 mm length of bolt complete all as specified.

S&F aluminium handles cast type anodised of 150 mm size complete all as specified.

S&F Powder coated anodised aluminium glazed window fixed type made up of 101.6x44.5x1.5 to 1.8 mm thick standard aluminium section in two or more panel incl necessary jointing cleats, glazing clips, rubber packing, aluminium snap beading screws, including glazing with 5.5 mm thick plain or tinted sheet glass complete all as specified.

S&F Powder coated anodised aluminium window sliding type three track aluminium sections weighing not less than 0.55 Kg per mtr (Two glazed shutter & one wire mesh shutter )incluiding necessary jointing cleats,glazing cleats,rubber packing anodised aluminium snap grinding, screws,handle,locking arrangement etc complete and 5.5 mm thick plain or tinted glass complete all as specified.

S&F mild steel framed work such as grills, gratings etc with ends of bars shouldered and / or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walkways, railings,frame work of watertanks and similar work conforming to Fe -290 Gde E-165 complete all as specified.

M&L of two coat of synthetic enamel paint over one coat of red oxide on new steel surfaces of any description over 10cm in width or girth incl preparation of surfaces complete all as specified and as directed.

M&L for preparation of new or previously untreated surfaces of wood and wood based surfaces of any description, over 10 cm in width or girth and apply two coat of synthetic enamel paint over a coat of pink primer complete all as specified.

M&L for applying two coats of acrylic distemper on newly plastered wall surface including preparation of surface over a coat of 1mm thick Birla wall care putty complete all as specified.

Material and Labour for preparation of new plastered surfaces and applying of two coats of cement base paint of wall surfaces complete all as specified.

M&L for PCC 1:3:6 type C2 using 40mm graded stone aggregate, 75mm thick in plinth protection and footpath laid in panels and finished even and smooth without using extra cement including necessary form work complete all as specified.Note : Joints 12mm wide to the full depth of PCC shall be provided at every 3 meters and at every change of direction and shall be filled with mixture of bitumen and sand 1:3 by weight. Cost of this provision shall be deemed to be included in the quoted rate for concrete in plinth protection complete all as specified.

S&F in Harrison rails (curtain), mild steel, chromium plated with fixing brackets stops, rollers etc complete all as specified and directed

M&L for chequered cement concrete tiles 20 cm x 20 cm x 22 to 25 mm thick set, jointed and pointed in neat cement slurry as in floors with grey cement and no pigments over and including 15 mm thick screed bed in cement mortor 1:6 complete all as specified.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out complete all as specified and directed

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm. complete all as specified and directed

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed

M&L for sand cushioning in cable trenches over & under the cable,with river washed coarse sand,as per standard practice with proper compaction complete all as specified.(Punned thickness18 cm shall be considered for payment as per para 19.75 of SSR Part-I)

S&L for bricks protection for protection of cable over sand cusioning cables inside the trench by using common burnt clay building bricks sub-class "B" old size brick and flat and width wise along the axies of the trench complete all as specified and directed

S&F 40mm dia GI tubing medium grade ISI marked laid in trenches/laid under floor for protection of cable including all fittings such as elbow,bends ,etc and short length complete all as specified.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc for taking credit ( credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and as directed.

M&L for point wiring complete with 1.5 Sqmm multistranded copper conductor single core PVC insulated unsheathed FR-LS cable 1100 volts grade (ISI marked) with proper colour coding drawn through and including non-metallic rigid PVC medium grade conduit not less that 20mm dia and conduit accessories (ISI marked) fixed over wall/fixed to roof, ceiling etc including provision of 1.5 Sqmm PVC insulated multistranded unsheathed copper conductor cable FR-LS (ISI marked) as earth continuity conductor connected to common earth dolly, fabricated sunken terminal box made out of GI sheet steel not less than 1.22 mm thick for boxes upto a size of 200 x 300mm and above this size not less than 1.63 mm thick duly painted with aluminum inside and anticorrosive paint outside, concealed in walls, with 3mm thick bakelite/plastic laminated sheet top cover fixed with cadmium plated iron screws for housing switches, socket outlets, fan regulators etc duly earthed including fixing arrangement for PVC conduits and sunken boxes over surface of wall/floor and matching with existing specifications. Connections of cable with MCBs or bus bar shall be sone through proper size copper/brass thimbles. conduit shall be fixed on surface with necessary saddles at no extra cost, One light point controlled by one way switch 5/6 amps all as specified and as directed.

All as per item No 63 above but One ceiling fan/Exhaut fan point controlled by one way switch 5/6 amps complete all as specified.

All as per item No 63 above butOne socket out let 5/6 amps point on the independent board complete all as specified.

All as per item No 63 above but One socket out let 5/6 amps point on the same board complete all as specified.

All as per item No 63 above but wiring with 2.5 sq mm single core copper conductor for one socket out let 15/16 amps point on the independent board complete all as specified.

S&F switch piano flush type 5/6 amps single pole one way complete all as specified.

S&F switch piano flush type 15/16 amps single pole one way complete all as specified.

S&F socket 2 in 1, 5 Pin, 5/6 amps, flash type complete all as specified.

S&F of socket outlet 2 in 1, 5 Pin, 5/15 amp, multipurpose 230 volt flash type complete all as specified.

S&F ceiling rose, bakelite, surface type, 220/240 volts, three terminals complete all as specified.

S&F fan regulator, 5 step(rotary stepped), electronic type, single phase,120/180 V, 400 watt, socket size incl connection complete complete all as specified & directed.

S&F wall mounted slim LED batten 20W(4' feet), with extruded aluminium housing, with polycarbonate diffuser and integrated LED driver complete all as specified and as directed.

S&f LED recessed mounted light (2'×2'),36 w suitable for indoor space including provision of three core PVC cable of copper conductor of size 23/.0076 and making connection complete all as specified and directed Make :Philips Cat No.RC380B LED 36S - 6500 G5 L60W60PSU OD SG or equivalent as in the list of makes.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed

Taking down carefully by unscrewing from boards/ outlet boxes, fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, brackets, ceiling fittings, bulk head fittings, tube light fittings and regulators, etc. complete all as specified and directed

Supply and Fixing sheet metal enclosure, 8 way Distribution Boards (DB's) double door,240 volts grade single pole and neutral with 200 amps rated bus bar,IP 20 protection fixed to wall using nuts & bolts and washer of suitable dia and grouted to wall using suitable gutties complete all as specified and as directed.

Supply and fixing amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of SPN 40 amp and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified.

Supply and fixing amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of SP 5 to 32 amp and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified.

M &L for Earthing complete with GI earth plate electrode 600x600x6mm thick buried directly in ground (Earth pit not less than 2.25M deep below normal ground level) with top edge of the plate not less than 1.5m below normal GL. Connected to galvanized earth lead wire 4mm dia by means of nut, bolt, check nut and washers including necessary excavation and earth work in soft/loose soil, GI protection pipe light grade 15mm bore for protecting the GI wire mesh funnel alternate layer of charcoal dust, and salt PCC pit 1:3:6 type C1 using 20mm graded stone aggregate and 50mm thick RCC 1:2:4 type B0 using 20mm graded stone aggregate cover re-inforced with 8 mm dia MS TMT bars 80mm C/C both ways complete all as specified and shown in Electrical plate No.3 SSR part-1 and connected to the earth point and testing complete all as specified.

M&L sub main wiring concealed type with two run single core cable PVC insulated cable with 4.0 Sq mm(Nominal area) multi stranded copper conductor FRLS cable1100 volts gde earth continuity conductor using PVC insulated cable of standed copper conductorof size 4.0 Sq mm connectedto common earth dolly and drawing into rigid PVC conduits of 25 mm dia medium grade size,making good the disturbed surface complete. NOTE:- One unit length shall measured as two run of main wire and one run of conduit & earth wire.

M&L for street light bracket, made out of GI pipe medium grade) 25mm bore, 1.2 m long bend to shape and fixing/grouting with wall using 2 Nos 25 x 5 mm size MS FI clamps with bolts, nuts & washers complete including drilling as necessary and two coats of Aluminium paint over a coat of Red oxide primer all as specified & directed.

S & F lamp holder, insulated body, with back plate suitable for batten/angle fittings complete all as specified and directed Make : Havells Reo.

S & F LED street light fittins 35 watt in aluminium PDC housing, toughned glass cover with IP66 protection complete all as spedified and as directed.

S&F MCB Triple pole & neutral, 63 amps, 415 volts, ‘C’ curve, 10 KA all complete including taking down the old one complete all as specified and directed by Engr-in-Charge.

S&F MCB, Single pole & neutral 6 to 32 amps, 240 volts, ‘C’ curve, 10 KA all complete including taking down the old one complete all as specified and directed by Engr-in-Charge.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 4 core all fixing and connecting accessories such as cable lugs, cable glands, nut, bolts, complete all as specified and as directed.

Supply,laying and testing cable XLPE insulated,screened,PVC bedded,galvanizedsteel strip or wire armoured heavy duty electric cable 1100v grade with stranded aluminium conductor of size 16 sq mm 4 core all fixing and connecting accessories such as cable lugs,cable glands,nut,bolts, complete all as specified and as directed. Note:- The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender, from total amount of Schedule 'A'/BOQ.

BHARAT ELECTRIC

M/S BISHAL ENTERPRISES

B L SHARMA

M/S. NARENDRA KUMAR GARG

M/S. GENERAL TRADING

M/S BIJAY KUMAR SHIVA

M/S. KUMAR CONSTRUCTION CO.