Clean Kerala Company Ltd (CKCL)-RKI- Establishing an Integrated Plastic Waste Management Facility at KINFRA, Kuttippuram, Malappuram

Amount

Site levelling

2.31 Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared

Solid Waste Collection & Management Center

2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

50.2.25.1 Filling with contractor's own earth ( excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

5.2.2 Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up tot floor five level excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

5.3 Reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (Zone III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources).

4.1.2 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

5.9.5 Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.9.19 Centering and shuttering including strutting, etc. and removal of form for:Weather shade, Chajjas, corbels etc., including edges

5.9.20 Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thick

5.22.6 Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

50.6.1.2 Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement: 6 coarse sand) etc complete.

13.1.1 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

13.46.1 Finishing walls with Acrylic Smooth exterior paint of required shade:New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

10.25.2 Item Shifted to Sub head 14 as item 14.73 Item Shifted to head 14 as item 14.74 Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

10.16.2 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished seamless type tubes

13.52.1 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work

12.50 Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

12.51.1 Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screwscomplete :Ridges plain (500-600 mm)

50.12.2.1 Providing & fixing Poly carbonate corrugated sheet 0.8 mm thick as approved by the Engineer in charge and should be supplied in a single length of 12 M or as decide by the Engineer in charge. The sheets shall be fixed using self drilling / self tapping screw of size (5.5x55 mm) with EPDM seal complete upto any pitch in horizontal/ vertical/ curved surface, but excluding the cost of purlins, rafters, trusses, and including cutting to size shapes where ever required.

OD125812/2025-2026 Od168009/2022_2023 : Supplying And Fixing Heavy Duty Rolling Shutter (Bearing Pully, Heavy Duty Gear Box Etc )Shutter Laths = 0.9 Mm Cr Materials, Bottom Plate Mm Tk, Guide Channel = 2Mm Tk, Top Cover = 0.4Mm Shutter Spring = Tata Wire)

9.143 Providing and fixing factory made uPVC door frame, made of uPVC extruded section, of size 65 mm x 55 mm with wall thickness 2.0 mm (? 0.2mm), corners of the door frame to be mitred cut and jointed with plastic brackets and stainless steel screws, reinforcing hinge side vertical of the frames with PVC profile of Size 28 mm x 30 mm having wall thickness 2 mm ( ? 0.2 mm), including providing & fixing 3 nos of 125 mm long stainless steel hinges to the frame, fixing the frame with jamb with required number & size of anchor dash fastners, all complete as per manufacturer's specification and direction of Engineer-in-charge.

9.144 Providing and fixing 37 mm thick factory made PVC door shutter, styles and rails made of PVC hollow section of size 100 mm x 37 mm with wall thickness 2 mm ( ± 0.2 mm), with inbuilt bead on one side, styles and rails mitered cut and joint at the corners by means of 2 nos of plastic brackets of size 75 mm x 220 mm at each corners by means of 2 nos of plastic brackets of size 75 mm x 220 mm at each corner and stainless steel screws, reinforcing the hinge side of style by inserting corner and stainless steel screws, reinforcing the hinge side of style by inserting PVC profile of size 28 mm x 30 mm, with wall thickness 2 mm ( ± 0.2 mm). Lockrail of size 100 mm x 37 mm, wall thickness 2 mm (± 02. mm) will be fixed to the vertical styles. Providing with PVC snapfit beads and panel of size 100 mm x 20 mm, and inserting 2 nos tie bar of 6 mm dia and fastening with nuts and washers complete, all as per manufacturer's specification and direction of Engineer -in- charge.

9.147D.3 Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 +/- 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Two track two panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 +/- 0.2 mm and single glazing bead / double glazing bead of appropriate dimension . (Area of window above 1.75 sqm upto 2.50 sqm).

12.41.2 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter

12.41.2 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter

50.18.9.22.11 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 110 mm dia Socket/ coupling

8.31 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in- Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

11.37 Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete

OD125101/2025-2026 Providing and fixing 200mm semi-Square uPVC gutter ( make : Euro Guard ) in all heights with iron brackets, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete. ( Excluding cost of Upvc fittings)

OD125102/2025-2026 Providing and fixing 200mm UPVC Center Joint ( make : Euro Guard ) in all heights with solvent cemet and washers etc. including making necessary connections with rain water pipes complete as per the Direction of Engineer in charge

OD125103/2025-2026 Providing and fixing 200mm UPVC Center Drop ( make : Euro Guard ) in all heights with solvent cemet and washers etc. including making necessary connections with rain water pipes complete as per the Direction of Engineer in charge

OD125104/2025-2026 Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement ,trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 200 mm dia 6Kgf/cm2

OD125105/2025-2026 Providing and fixing 200mm UPVC End Drop ( make : Euro Guard ) in all heights with solvent cemet and washers etc. including making necessary connections with rain water pipes complete as per the Direction of Engineer in charge

OD125106/2025-2026 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 200 mm dia Socket/ coupling

OD125107/2025-2026 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 200X110mm Reducer

OD125108/2025-2026 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 200mm Bend

OD125109/2025-2026 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 200mm PVC Tee

OD125110/2025-2026 Providing and fixing 21" stainless steel Turbo fan including cost of material, errction etc all complete as per the Direction of Engineer in charge

8.32 Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design.(b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. (c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.

Land Development

16.79 Providing , laying spreading and compacting graded stone aggregate ( size range 53 mm to 0.075 mm) to wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant, carriage of mixed material by tipper to site, for all leads & lifts, laying in uniform layers with mechanical paver finisher in sub - base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achieve the desired density, complete as per specifications and directions of Engineer - in- Charge.

16.1 Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and rerolling the sub grade and disposal of surplus earth with lead upto 50 metres.

16.91.2 Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.

Water Collection Tank

2.8.1 Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

5.1.2 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size derived from natural sources)

5.2.2 Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up tot floor five level excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

5.3 Reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (Zone III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources).

5.9.1 Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.2 Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.6 Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

5.22.6 Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

13.1.1 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

22.3 Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C. kitchen and the like consisting of : i) I course of applying cement slurry @ 4.4 Kg/ sqm mixed with water proofing compound conforming to IS: 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. ii) II course of 20 mm cement plaster 1:3 ( 1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. iii) III course of applying blown or residual bitumen applied hot at 1.7 kg per sqm of area. iv) IV course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 Kg/ sqm.

OD125111/2025-2026 Providing and laying water proofing treatment for wall surface by using High Pressure Grouting machine with water proof chemical, including cost of all materials, labor, Chemical, Pressure Grouting machine hire charge etc all complete as per the Direction of Engineer in charge

OD125114/2025-2026 Providing and fixing in position FRP manhole cover and frame of required shape and approved quality Square shape 900X900 mm including cost of all material, labour, conveying, errection etc all complete as per the Direction of Engineer in charge

Office Room & Fire Tank

2.8.1 Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

5.1.2 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size derived from natural sources)

5.2.2 Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up tot floor five level excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

5.3 Reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (Zone III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources).

5.9.1 Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.5 Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.9.6 Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

5.9.16.1 Centering and shuttering including strutting, etc. and removal of form for: Edges of slabs and breaks in floors and wallsUnder 20 cm wide

5.9.19 Centering and shuttering including strutting, etc. and removal of form for:Weather shade, Chajjas, corbels etc., including edges

5.9.20 Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thick

5.9.2 Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc

5.22.6 Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

50.6.1.2 Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement: 6 coarse sand) etc complete.

13.1.1 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

22.3 Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C. kitchen and the like consisting of : i) I course of applying cement slurry @ 4.4 Kg/ sqm mixed with water proofing compound conforming to IS: 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. ii) II course of 20 mm cement plaster 1:3 ( 1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. iii) III course of applying blown or residual bitumen applied hot at 1.7 kg per sqm of area. iv) IV course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 Kg/ sqm.

13.46.1 Finishing walls with Acrylic Smooth exterior paint of required shade:New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

10.16.2 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished seamless type tubes

13.52.1 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work

12.50 Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

12.51.1 Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screwscomplete :Ridges plain (500-600 mm)

9.143 Providing and fixing factory made uPVC door frame, made of uPVC extruded section, of size 65 mm x 55 mm with wall thickness 2.0 mm (? 0.2mm), corners of the door frame to be mitred cut and jointed with plastic brackets and stainless steel screws, reinforcing hinge side vertical of the frames with PVC profile of Size 28 mm x 30 mm having wall thickness 2 mm ( ? 0.2 mm), including providing & fixing 3 nos of 125 mm long stainless steel hinges to the frame, fixing the frame with jamb with required number & size of anchor dash fastners, all complete as per manufacturer's specification and direction of Engineer-in-charge.

9.144 Providing and fixing 37 mm thick factory made PVC door shutter, styles and rails made of PVC hollow section of size 100 mm x 37 mm with wall thickness 2 mm ( ± 0.2 mm), with inbuilt bead on one side, styles and rails mitered cut and joint at the corners by means of 2 nos of plastic brackets of size 75 mm x 220 mm at each corners by means of 2 nos of plastic brackets of size 75 mm x 220 mm at each corner and stainless steel screws, reinforcing the hinge side of style by inserting corner and stainless steel screws, reinforcing the hinge side of style by inserting PVC profile of size 28 mm x 30 mm, with wall thickness 2 mm ( ± 0.2 mm). Lockrail of size 100 mm x 37 mm, wall thickness 2 mm (± 02. mm) will be fixed to the vertical styles. Providing with PVC snapfit beads and panel of size 100 mm x 20 mm, and inserting 2 nos tie bar of 6 mm dia and fastening with nuts and washers complete, all as per manufacturer's specification and direction of Engineer -in- charge.

9.147D.3 Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 +/- 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Two track two panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 +/- 0.2 mm and single glazing bead / double glazing bead of appropriate dimension . (Area of window above 1.75 sqm upto 2.50 sqm).

12.41.2 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter

50.18.9.22.11 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 110 mm dia Socket/ coupling

50.18.9.22.4 Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement- 110 mm dia Bend

11.41.2 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm.

8.31 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in- Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

11.37 Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete

OD125112/2025-2026 Providing and laying water proofing treatment for wall surface by using High Pressure Grouting machine with water proof chemical, including cost of all materials, labor, Chemical, Pressure Grouting machine hire charge etc all complete as per the Direction of Engineer in charge

OD125120/2025-2026 Providing and fixing 150mm semi-Square uPVC gutter ( make : Euro Guard ) in all heights with iron brackets, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete. ( Excluding cost of Upvc fittings)

OD125121/2025-2026 Providing and fixing 150mm UPVC End Drop ( make : Euro Guard ) in all heights with solvent cemet and washers etc. including making necessary connections with rain water pipes complete as per the Direction of Engineer in charge

OD125122/2025-2026 Providing and fixing 150mm UPVC Square Jointer ( make : Euro Guard ) in all heights with solvent cemet and washers etc. including making necessary connections with rain water pipes complete as per the Direction of Engineer in charge

OD125123/2025-2026 Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 150X110mm Reducer

Fire Fighting

OD125541/2025-2026 "TERRACE PUMP - 900 LPM, 7.5 HP - SUPPLY INSTALLATION TESTING AND COMMISSIONING OF HORIZONTAL MOUNTED MONO BLOCK THREE PHASE PUMP SET WITH CAST IRON CASING CAST IRON IMPELLER COUPLED TOA SQUIRELL CAGE INDUCTION MOTOR TEFC TYPE WITH SUPPLY CONDITION OF 415 V 3 PH 50 HZ RATED FOR 900 LPM SUITABLE HP AT 2900 RPM"

OD125542/2025-2026 "MCC PANEL FOR PUMP - AUTOMATIC PANEL - SUPPLY INSTALLATION TESTING AND COMMISSIONING OF MOTOR CONTROL PANEL FOR AUTOMATIC OPERATION OF TERRACE PUMP WITH DOL STARTER.THE PANEL SHALL BE PAINTED WITH ANTICORROSIVE LACQUER AND WITH PROTECTIVE LOCKABLE ARRANGEMENT"

OD125543/2025-2026 "BUTTERFLY VALVE - LEVER OPERATED - SUPPLY INSTALLATION TESTING AND COMMISSIONING OF WAFER TYPE BUTTERFLY AVLVE, CAST IRON BODY, SS 420 SHAFT, MILD STEEL HANDLE , DISC OF SS 304 PRSSURE RATING OF PN 10 LEVER OPERATED TYPE AS PER IS : 13095 FITTED WITH NECESSARY DIA FLANGES GASKETS NUTS AND BOLTS ETC - 100 MM DIA"

OD125544/2025-2026 "BUTTERFLY VALVE - LEVER OPERATED - SUPPLY INSTALLATION TESTING AND COMMISSIONING OF WAFER TYPE BUTTERFLY AVLVE, CAST IRON BODY, SS 420 SHAFT, MILD STEEL HANDLE , DISC OF SS 304 PRSSURE RATING OF PN 10 LEVER OPERATED TYPE AS PER IS : 13095 FITTED WITH NECESSARY DIA FLANGES GASKETS NUTS AND BOLTS ETC - 80 MM DIA"

OD125545/2025-2026 "NON RETURN VALVE - SLIM SEAL , CI - SUPPLY INSTALLATION TESTING AND COMMISSIONING OF SLIM SEAL TYPE CAST IRON NON RETURN VALVES FITTED WITH NECESSARY DIA FLANGES GASKETS NUTS AND BOLTS ETC"

OD125546/2025-2026 "PRESSURE SWITCH - SUPPLY INSTALLATION TESTING AND COMMISSIONING OF PRESSURE SWITCH FOR AUTOMATIC OPERATION OF PUMPS"

OD125547/2025-2026 "PRESSURE GAUGE - SUPPLY INSTALLATION TESTING AND COMMISSIONING OF PRESSURE GAUGE OF 0-12 KG RANGE WITH 4"" SIZE DIAL"

OD125548/2025-2026 "MS "" B "" CLASS PIPE - ABOVE GROUND - SUPPLY INSTALLATION TESTING AND COMMISSIONING OF MS "" B "" CLASS PIPES CONFIRMING TO IS : 1239 WITH SPECIALS CONFIRMING TO IS : 1239 PART II SUCH AS ELBOWS REDUCERS FLANGES ETC INCLUDING CUTTING WELDING FIXING ON WALLS OR CEILING BY USING SUITABLE SUPPORTS WITH TWO COATS OF ZINC CHRO

OD125549/2025-2026 "MS "" B "" CLASS PIPE - ABOVE GROUND - SUPPLY INSTALLATION TESTING AND COMMISSIONING OF MS "" B "" CLASS PIPES CONFIRMING TO IS : 1239 WITH SPECIALS CONFIRMING TO IS : 1239 PART II SUCH AS ELBOWS REDUCERS FLANGES ETC INCLUDING CUTTING WELDING FIXING ON WALLS OR CEILING BY USING SUITABLE SUPPORTS WITH TWO COATS OF ZINC CHROMITE YELLOW PRIMER AND ENAMEL PAINT RED COLOUR- 80 MM DIA"

OD125550/2025-2026 "MS "" B "" CLASS PIPE - ABOVE GROUND - SUPPLY INSTALLATION TESTING AND COMMISSIONING OF MS "" B "" CLASS PIPES CONFIRMING TO IS : 1239 WITH SPECIALS CONFIRMING TO IS : 1239 PART II SUCH AS ELBOWS REDUCERS FLANGES ETC INCLUDING CUTTING WELDING FIXING ON WALLS OR CEILING BY USING SUITABLE SUPPORTS WITH TWO COATS OF ZINC CHROMITE YELLOW PRIMER AND ENAMEL PAINT RED COLOUR- 65 MM DIA

OD125551/2025-2026 "MS "" B "" CLASS PIPE - ABOVE GROUND - SUPPLY INSTALLATION TESTING AND COMMISSIONING OF MS "" B "" CLASS PIPES CONFIRMING TO IS : 1239 WITH SPECIALS CONFIRMING TO IS : 1239 PART II SUCH AS ELBOWS REDUCERS FLANGES ETC INCLUDING CUTTING WELDING FIXING ON WALLS OR CEILING BY USING SUITABLE SUPPORTS WITH TWO COATS OF ZINC CHR

OD125552/2025-2026 "MS "" B "" CLASS PIPE - ABOVE GROUND - SUPPLY INSTALLATION TESTING AND COMMISSIONING OF MS "" B "" CLASS PIPES CONFIRMING TO IS : 1239 WITH SPECIALS CONFIRMING TO IS : 1239 PART II SUCH AS ELBOWS REDUCERS FLANGES ETC INCLUDING CUTTING WELDING FIXING ON WALLS OR CEILING BY USING SUITABLE SUPPORTS WITH TWO COATS OF ZINC CHROMITE YELLOW PRIMER AND ENAMEL PAINT RED COLOUR- 40 MM DIA"

OD125553/2025-2026 "MS "" B "" CLASS PIPE - ABOVE GROUND - SUPPLY INSTALLATION TESTING AND COMMISSIONING OF MS "" B "" CLASS PIPES CONFIRMING TO IS : 1239 WITH SPECIALS CONFIRMING TO IS : 1239 PART II SUCH AS ELBOWS REDUCERS FLANGES ETC INCLUDING CUTTING WELDING FIXING ON WALLS OR CEILING BY USING SUITABLE SUPPORTS WITH TWO COATS OF ZINC CHROMITE YELLOW PRIMER AND ENAMEL PAINT RED COLOUR- 32 MM DIA"

OD125554/2025-2026 "MS "" B "" CLASS PIPE - ABOVE GROUND - SUPPLY INSTALLATION TESTING AND COMMISSIONING OF MS "" B "" CLASS PIPES CONFIRMING TO IS : 1239 WITH SPECIALS CONFIRMING TO IS : 1239 PART II SUCH AS ELBOWS REDUCERS FLANGES ETC INCLUDING CUTTING WELDING FIXING ON WALLS OR CEILING BY USING SUITABLE SUPPORTS WITH TWO COATS OF ZINC CHROMITE YELLOW PRIMER AND ENAMEL PAINT RED COLOUR- 25 MM DIA"

OD125555/2025-2026 "BALL VALVE - 25 MM DIA - SUPPLY INSTALLATION TESTING AND COMMISSIONING OF 25 MM DIA BALL VALVE SCREWED END TYPE WITH CAST IRON BODY"

OD125556/2025-2026 "AIR RELEASE VALVE - 25 MM DIA - SUPPLY INSTALLATION TESTING AND COMMISSIONING OF 25 MM DIA AIR RELEASE VALVE SCREWED END TYPE WITH CAST IRON BODY"

OD125557/2025-2026 "FIRE BRIGADE INLET - 2 WAY - SUPPLY INSTALLATION TESTING AND COMMISSIONING OF FIRE BRIGADE INLET CONNECTION WITH 3 NOS OF 63 MM BUILT IN NON RETURN VALVES IN 100 MM PIPE MANIFOLD DIRECTLY CONNECTED TO RISER"

OD125558/2025-2026 "HYDRANT VALVE - SUPPLY INSTALLATION TESTING AND COMMISSIONING OF STAINLESS STEEL OBLIQUE TYPE SINGLE HEADED HYDRANT VALVE SS : 304 OF 63 MM DIAFLANGED INLET AS PER PN 16 AND 63 MM DIA FEMALE INSTANTANEOUS OUTLET WITH STAINLESS STEEL INSTANTANEOUS COUPLING ADAPTOR WITH PVC BLACK CAP ETC"

OD125559/2025-2026 "HOSE REEL DRUM - IMPORTED - SUPPLY INSTALLATION TESTING AND COMMISSIONING OF HYDRAULIC HOSE REEL DRUM [ WALL MOUNTING TYPE ] HAVING IS: 884 STANDARD WITH SWINGING DRUM POWDER COATED RED FINISHED AT AN OPERATING PRESSURE OF 150 PSI AND FLOW RATE OF 16 GPM AT 100 PSI WITH 19 MM PVC HOSE HAVING LENGTH OF 30 MTR WITH STOP COCK AND PVC NOZZLE AND OTHER FIXING ACCESSORIES"

OD125560/2025-2026 "FIRE HOSE - SUPPLY INSTALLATION TESTING AND COMMISSIONING OF FIRE HOSE OF UL LISTED AND IS 636 TYPE A IN 15 MTR LENGTH OF 63 MM DIA WORKING PRESSURE OF 175 PSI TESTED AT BURSTING PRESSURE OF 640 PSI WITH STAINLESS STEEL COUPLING BINDED WITH STAINLESS STEEL WIRE"

OD125561/2025-2026 "BRANCH PIPE - SUPPLY INSTALLATION TESTING AND COMMISSIONING OF STAINLESS STEEL BRANCH PIPE WITH 63 MM HEXAGONAL BASE NOZZLE"

OD125562/2025-2026 HOSE BOX - SINGLE DOOR - SUPPLY INSTALLATION TESTING AND COMMISSIONING OF SINGLE DOOR HOSE CABINET OF INTERNAL TYPE TO PLACE ONE CP HOSE ALONG WITH COUPLINGS AND ONE BRANCH PIPE

OD125563/2025-2026 "SPRINKLER BULB - SUPPLY INSTALLATION TESTING AND COMMISSIONING OF SPRINKLER BULB UL LISTED MADE OUT OF BRONZE 1/2 INCH INLET CONNECTION OF RATED TEMPERATURE 68 DEGREE CELCIOUS WITH NATURAL FINISH AT MAXIMUM WORKING PRESSURE OF 175 PSI WITH COMPLEATE FITTINGS OF FOLLOWING TYPES"

OD125564/2025-2026 "ABC FIRE EXTINGUISHER - 4 KG - SUPPLY INSTALLATION TESTING AND COMMISSIONING OF ABC TYPR FIRE EXTINGUSHER OF CAPACITY 4 KG WITH CONTROLLABLE DISCHARGE MECHANISUM"

OD125565/2025-2026 FACP - FIRE ALARM CONTROL PANEL - SUPPLY INSTALLATION TESTING AND COMMISSIONING OF 2 ZONE CONVENTIONAL FIRE ALARM PANEL WITH 2 X 16 CHARACTER LCD DISPLAY NO / NC CONTACT FOR FIRE AND FAULT LCD AND LED INDICATION FOR OPEN SHORT CIRCUIT FIRE IN EACH ZONE ETC

OD125566/2025-2026 "SMOKE DETECTOR - SUPPLY INSTALLATION TESTING AND COMMISSIONING OF SMOKE DETECTOR WITH BASE PHOTO ELECTRIC TYPE WITH ALL FIXING ACCESSORIES"

"MCP - MANUAL CALL PONIT [ ABS ] - SUPPLY INSTALLATION TESTING AND COMMISSIONING OF MAUAL CALL POINT OF RED COLOURED TOUGH DURABLE HIGHLY VISIBLE WITH ALARM LED TO INDICATE ALARM CONDITION AVAILABLE FOR FLUSH OR SURFACE MOUNTING"

OD125568/2025-2026 "SUNDER [ ABS ] - SUPPLY INSTALLATION TESTING AND COMMISSIONING OF ELECTRONIC SOUNDER FOR PROVIDING AN AUDIO WARNING WHICH IS SUITABLE FOR PLACE WHICH NEED AUDIO INDICATION"

OD125569/2025-2026 "CABLING - SUPPLY INSTALLATION TESTING AND COMMISSIONING OF PVC INSULATED 1 SQ MM COPPER CABLE"

ETP Tank (20KLD)

2.8.1 Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

5.1.2 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size derived from natural sources)

5.2.2 Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up tot floor five level excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

5.9.1 Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.2 Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.22.6 Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

OD127197/2025-2026 OD from 51.13.21.1- Water proof plastering with Cement Mortar 1:4 (1 cement : 4 fine sand) 12mm thick plaster finished with a floating coat of neat cement mixed with water proofing compound of approved make @ 2kg/m2 of mix floated hard and troweled smooth including all labour, material, conveyance charges etc complete

10.16.2 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished seamless type tubes

12.50 Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

12.51.1 Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screwscomplete :Ridges plain (500-600 mm)

50.6.1.2 Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement: 6 coarse sand) etc complete

13.1.1 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

13.46.1 Finishing walls with Acrylic Smooth exterior paint of required shade:New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

9.143 Providing and fixing factory made uPVC door frame, made of uPVC extruded section, of size 65 mm x 55 mm with wall thickness 2.0 mm (? 0.2mm), corners of the door frame to be mitred cut and jointed with plastic brackets and stainless steel screws, reinforcing hinge side vertical of the frames with PVC profile of Size 28 mm x 30 mm having wall thickness 2 mm ( ? 0.2 mm), including providing & fixing 3 nos of 125 mm long stainless steel hinges to the frame, fixing the frame with jamb with required number & size of anchor dash fastners, all complete as per manufacturer's specification and direction of Engineer-in-charge.

9.144 Providing and fixing 37 mm thick factory made PVC door shutter, styles and rails made of PVC hollow section of size 100 mm x 37 mm with wall thickness 2 mm ( ± 0.2 mm), with inbuilt bead on one side, styles and rails mitered cut and joint at the corners by means of 2 nos of plastic brackets of size 75 mm x 220 mm at each corners by means of 2 nos of plastic brackets of size 75 mm x 220 mm at each corner and stainless steel screws, reinforcing the hinge side of style by inserting corner and stainless steel screws, reinforcing the hinge side of style by inserting PVC profile of size 28 mm x 30 mm, with wall thickness 2 mm ( ± 0.2 mm). Lockrail of size 100 mm x 37 mm, wall thickness 2 mm (± 02. mm) will be fixed to the vertical styles. Providing with PVC snapfit beads and panel of size 100 mm x 20 mm, and inserting 2 nos tie bar of 6 mm dia and fastening with nuts and washers complete, all as per manufacturer's specification and direction of Engineer -in- charge.

9.147D.3 Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 +/- 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Two track two panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 +/- 0.2 mm and single glazing bead / double glazing bead of appropriate dimension . (Area of window above 1.75 sqm upto 2.50 sqm).

OD125158/2025-2026 Providing and fixing in position FRP manhole cover and frame of required shape and approved quality Square shape 600x600 mm including cost of all material, labour, conveying, erection etc all complete as per the Direction of Engineer in charge

OD125159/2025-2026 Providing and fixing in position FRP manhole cover and frame of required shape and approved quality Square shape 900X900 mm including cost of all material, labour, conveying, errection etc all complete as per the Direction of Engineer in charge

OD125160/2025-2026 Supply, installation, testing and commissioning of coarse bar screen of SS 304 construction using SS Mesh of 10 mm Mesh Size, detachable type with hand, frame, risings, suitable for placing inside a bar screen chamber of size 0.80 mtrX0.50 mtr Make : Flow Max

OD125161/2025-2026 Providing, fixing, testing & commissioning of fully submersible, centrifugal non-clog type Effluent handling pumps capable of handling solids up to 30-35 mm for raw Effluent transfer from collection tank to anaerobic tank. The pump shall have non clog casting & impeller, SS shaft, TEFC induction motor, flexible pipe with coupling connected to be delivery header etc. complete as required. Accessories:, coupling nylon rope for lifting etc...Complied. Sewage Transfer Pumps: Flow rate (each): 1 1.5m3/hr., 1-1.5 Hp, 3phase. Head: 8-12 MLC. Solid Handling - 30-35 mm.Type : Open type centrifugal Make : Crompton/Lubi

OD125162/2025-2026 Supply, Installation, testing and commissioning of Anaerobic Fill Media in anaerobic tank with all accessories. The sheets shall be neatly pasted and packed tightly as per the guidelines from the engineer in charge. Surface area of the sheet is 240 m2/m3, Color - Black, Make : MM Aqua/Eqt

OD125163/2025-2026 Supply & filling of MBBR Media in Aeration tank as per the direction of Engineer in Charge, Surface Area of the media is 500-600m2/m3, Shape : Cylindrical, Size 12mm x 25 mm, MOC:PE-Virgin, Color : White, Specific Gravity : 0.94g/cc or Above. Media Quantity: 95000-100000 pcs/Cum Make : Small Boss/Eqt

OD125164/2025-2026 SITC of Twin Type Rotary Air Blowers and Motors with casing –CI, shaft-Alloy Steel, capable of delivering 50 cum/hr (each) of free air coupling to a TEFC motor of suitable HP suitable for 415 ± 10% volts, 3 phase, 0 cycles A/C supply complete with following accessories installed in RCC foundation with suitable size foundation bolts complete as required. Common base frame for motor & compressor with motor base plate and Belt and pulley arrangement etc. Air Suction and Discharge companion flanges. Suction Silencer with Suitable Flanges. Suction Air Filter (Dry Bag Type).Pressure gauge and pressure relief valve (Spring loaded type)<.Compressor & motor pulley/coupling with guard. Capacity: 50 m3/hr. Pressure - 0.30 bar. Make : A one /Everest

OD125165/2025-2026 SITC of Non-clog type Fine bubble diffuser for aeration in aeration tank. Capable of handling 2-8 cfm of air with oxygen transfer efficiency of 3-4% per meter water depth. . Air dispersion system shall be provided for aeration tank -10 Nos with CPVC pipes / CPVC Pipes connected to the distributor which are duly supported in free standing Concrete block with suitable size SS clamp etc. complete as required. Design flow: 2 m3/hr to 8 m3/hr. Connection 1&quot;-1.5&quot; NPT male. Size of diffuser: 90 mm dia X 1000 mm long. Type: Tubular, Membrane Material: EPDM. Make : Proflex/Scogen/Eqt

OD125166/2025-2026 Providing, fixing, testing and commissioning of electronic Chemical dosing system comprising of electronic metering pump (with both frequency and stroke length controls to control the dosage rate between 10-100% of rated maximum capacity) virgin HDPE chemical grade solution tank of 30 ltr capacity, necessary injection fitting assembly foot valve cum strainer and suction and delivery tubing etc. up to the point of injection complete in all respects as required. Dosing pump shall be Electronically operated, Mechanically Actuated diaphragm. Dosing Capacity 6 lph. Pressure : 4 Bar Make : FC Dose/E-Dose

OD125167/2025-2026 Providing, fixing, testing & commissioning of surface mounted, self-priming, and centrifugal, Horizontal, non-clog type water pumps (Re-Circulation Pump). The pump shall have non clog casting &amp; impeller, TEFC induction motor including pressure gauge. Accessories: Base plate, Coupled/monoblock, priming arrangement, mechanical seal, pressure gauge with isolation cock etc.. The pump shall be suitable for 415 & 10% volts 3 phase AC supply. Complied. Flow rate (each) : 1 LP/Sec, 0.5 Hp, 3phase. Head : 8-11 MLC..Type : Open type centrifugal. Make : Kirloskar/Crompton/Lubi

OD125168/2025-2026 Providing, fixing, testing & commissioning of surface mounted, centrifugal, Horizontal, non-clog clear water pumps (Filter Feed Pump). The pump shall have non clogg casting &amp; impeller, TEFC induction motor including pressure gauge. Complete as required. Accessories: Base plate, Coupled/mono block, priming arrangement, mechanical seal, pressure gauge with isolation cock etc.. The pump shall be suitable for 415 & 10% volts 3 phase AC supply. Complied. Flow rate (each) : 1-1.5 M3/hr, 1-2 Hp, 3phase. Head : 25-30 MLC Make : Kirloskar/Cromton/Lubi

OD125169/2025-2026 Supply, installation, testing and commissioning of Multi graded Pressure sand Filter with the capacity of 1000 lph, operating pressure 3.5 Bar, Maximum Operating Pressure 5 Bar. Vertical Type with 1NB Top Mount Multi port Valve (Filter, Rinse, Backwash Etc.). Multi-port Max. Operating Pressure 5 Bar. Media: gadded pebble/Silex, Coarse sand or Fine Sand. Accessories: strainers, Pressure gauge etc. Size : 14" x 65 " , MOC : FRP Make : Pentair /Eqt

OD125170/2025-2026 Supply, installation, testing and commissioning of Activated Carbon Filter with the capacity of 1000 lph, operating pressure 3.5 Bar, Maximum Operating Pressure 5 Bar. Vertical Type with 1NB Top Mount Multiport Valve (Filter, Rinse, Backwash Etc.). Multi-port Max. Operating Pressure 5 Bar. Media: gadded pebble/Silex, Coarse sand or Fine Sand. Accessories: Strainers, Pressure gauge etc. Size : 14" x 65", MOC : FRP Make : Pentair /Eqt

OD126638/2025-2026 Providing and fixing GI pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement/welding/cpvc solvent/upvc solvent and testing of joints complete as per direction of Engineer-in-Charge All sizes -Internal/External work- Exposed on wall As per detailed specification( for 296 m long) Quantity: 1 Lot.

Internal Plumbing Works

17.3.1 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern &amp; C.P. flush bend with fittings &amp; C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid

17.7.8 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Surgeon type wash basin of size 660x460 mm with a pair of 15 mm C.P. brass pillar taps with elbow including operated levers

50.17.1.4 Supplying and fixing CP Health faucet good quality including cost of materials and labour charges etc. complete as per the direction of site engineer-in-charge.

18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank :ISI 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

50.18.8.9.1 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chased and making good the wall etc. 110 mm pipe 6kgf/cm2

50.18.7.5.1 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes &amp; fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 40 mm dia 10 Kgf/cm2- Internal work- exposed on wall

51.19.ST3 Supplying and installing ready made PVC Septic tank including the cost of carriage, trenching, placing at the level below ground level as specified as per the direction of engineer in charge (Provision for CC/RCC/Sand/06mm aggregate for the preparation of bed shall be paid separately)&lt;br&gt; 3. 25 to below 35 flush capacity

18.51.1 Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore

18.53.1 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 893115 mm nominal bore

17.73.1 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm. weighing not less than 170 gms

17.69.1 Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour.Waste coupling 31 mm dia of 79 mm length and 62 mm breadth weighing not less than 45 gms

18.58.1.1 Providing and fixing PTMT grating of approved quality and colour. Circular type100 mm nominal dia

50.18.7.2.1 Providing and fixing PVC pipes, fittings including fixing the pipe with claps at 1.00 metre spacing. This includes jointing of pipes &amp; fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 20 mm dia 12Kgf/cm2 - Internal work - Exposed on wall

50.18.7.3.1 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes &amp; fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer- in- Charge 25 mm dia 12 Kgf/cm2 - Internal work - Exposed on wall

2.8.1 Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

50.6.1.2 Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement: 6 coarse sand) etc complete.

5.9.20 Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thick

5.22.6 Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

4.1.2 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

EXCLUSIVE OF GST

Note :1 All materials, Items, Equipment shall be best branded items with IS and approved by client/KEL

2:Rate should be inclusive of Insurance,Transportation, delivery and installation cost for all items

3.Rate should be Exclusive of GST.

4.Work should be executed as per DSR/PWD specification and direction of Engineer at site.

5.CEMENT: Make use Malabar cement only as per Govt. direction and in case of non availabilty of Malabar cement use Ultra Tech, Dalmia, Ramco or eq. brand in the order of preference.

6.RCC: (Assessment of strength of concrete by Cube testing at Approved Govt labs as per IS) Cement make: Use Malabar cement only as per Govt. direction and in case of non availabilty of Malabar cement use Ultra Tech, Dalmia, Ramco or eq. brand in the order of preference.

7.STEEL REINFORCEMENT: Make: Tata,Vaishak, SAIL, JSW or eq primary make in the order of preference

8.CENTERING & SHUTTERING: (Centering and shuttering for different category of work may be considered separately.)

9. SOLID BLOCK MASONRY: Min. average compressive strength as per IS shall be 40-50kg/cm2 and has to be assessed by testing at Govt. lab. ( Variation in rate due to change in size of block and level of floor as per DSR/PRICE has to be considered)

10.PLUMBING & SANITARY FITTINGS: Note: Make of Water supply and sanitary items: Best branded ISI make Jaquar, Cera, Hindware, Parryware or eq. in the order of pref. Water pipe: Supreme, Finolex or eq. with IS and all fittings with IS.

11.VITRIFIED FLOOR TILES/ CERAMIC GLAZED WALL TILES: Make: Khajaria, Jhonson, RAK, NITCO, Cera or Eq. in the order of preference and prior sample approval from KEL, Client

12.Rigid PVCPipes/Casing & Capping - A-ONE/REPUTED MAKE with ISI , Precession, Balco, GEO

saaj constructions (BID ID -2296061)

CUBIX INFRASTRUCTURES (BID ID -2297803)