SPECIAL REPAIR OF MES BLDG NO P-64/02 (TYPE-IV) ACCN AT CG COMPLEX UNDER GE LUDHIANA

Amount

Sch 'A' sec-I

Demolition of cement concrete (unreinforced) concrete in ground floors and paving n exc 15cm thickness ( below or above ground floors.)

Dismantling floor hearth or wall tiling including cement mortar bedding but not backing removing serviceable tiles to store and rubbish off the premises .

S&F for light shade vitrified colour tiles 600mmx600mmx10mm thick area of each tile not exceeding 0.36 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cenemt to match over 15mm thick screed bed in cement mortar (1:6) all as specified and directed.

-ditto- all as per item no 03 above but in skirting/dado laid over 10mm thick cement screed in cm 1:4 complete all as specified.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile 0.11 Sqm but n.exc 0.18 Sqm, in neat cement slurry and pointed in white or coloured cement with pigment to match over 15mm thick screed bed in cement mortar (1:6) all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile 0.06 Sqm but n.exc 0.11 Sqm, in neat cement slurry and pointed in white or coloured cement with pigment to match over 15mm thick screed bed in cement mortar (1:6) all as specified and directed.

M&L for glazed ceramic coloured designer pattern tiles / printed tiles 450X350X7mm thick on vertical surfaces as in skirting/dado, set and jointed with neat cement slurry and pointed in white/coloured cement to match the shade of tiles over 10mm thick rendering in cement mortar 1:4.

M&L for 25mm thick Cement concrete 1:2:4 type B-0 using 12.5 mm graded stone aggr.as in sub flooring rough finished surface complete all as spd and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, approns and laid bedded and pointed in any mortar atc.

M&L for granite 20mm thick(table rubbed and polished) in cooking plateform and like in cement mortar 1:4 including pointing in white cement(1:2) using marble dust making holes in RCC shelves suitable for gas pipe with round edges where required complete all as directed.

M&L for granite 20mm thick Granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.

M&L for 50mm thick cement concrete 1:3:6 type C1 using 20mm graded stone aggregate as in plinth protection joint filled with bitumen sand mixer 50mm thick finished even and smooth without using extra cement.

M&L for repairing RCC projection chajjas, roof, facia etc. by necessary preparation, scraping, cutting, chiseling derusting and cleaning exposed reinforcement surfaces of damaged, loose RCC surfaces with cement concrete (1:1.5:3) using 12.5mm graded crushed stone aggregates and reinforcement with welded mesh of weight exc 2Kg per Sqm but n.exc 3Kg/Sqm (if required) with or without facia and finished with cement morte 1:3 using coarse sand and work in patches area n.exc 5 Sqm and thickness RCC member n.exc 70mm incl necessary formwork and applying two coats of finishes to match with the existing surfaces at any height complete. (note: wlded mesh to be paid separately)

M&L for expanded metal (welded mesh) n.exc 4Kg/Sqm cut to length bent to shape reqd and tying with & including annealed mild steel wire not less than 0.9mm or fixing with glavanised steel staples fixed to steel members with nut & bolt or fixed to RCC work or ceiling surfaces.

Taking down or up steel tubing and connections inculding cleaning for refixing or removal to store 15mm bore

Taking down or up steel tubing and connection s inculding cleaning for refixing or removal to store 20mm bore .

S&F for tube 'medium grade' galavanised, with all fitting and fixed complete to walls and ceiling etc 15mm bore.

-ditto- all as per item No 17 above but 20mm bore.

S&F in repair Bib taps chromium plated fancy type, cast copper alloy with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed in repair 15mm bore complete all as specified and directed by Engineer-in-Charge.

S&F for stop cock fancy type chromium plated with long shank and cup(Concealed type) screwed down high pressure with crutch or butterfly handle screwed bot ends for iron pipe or for union and fixed 15mm bore fixed in repair.

S&F for stop cock /Angle cock fancy type chromium plated with cast copper alloy screwed down high pressure with or without lattered hot and cold with long screwed shanks and fly nuts fixed in repair 15mm bore.

S&F for brass CP mixer/Mixing valve on walls for mixing hot & cold water screwed down for iron pipe , including two-in-one joints to steel pipes or unions and plugging and screwing to walls and fixed 15mm bore fixed in repairs comlete all as specified.

S&F for cast copper alloy chromium plated fancy type single lever basin mixer .

S&F for cast copper alloy chromium plated fancy type double lever Sink mixer .

S&F for PVC connection 15mm bore size with PTMT nuts of length 45cm.

S&F in repairs PVC valveless syphonic action type flushing cistern, low level white with inlet ball valve flaot and handle including brackets. 10 ltr capacity.

S&F for plastic water closed seat white closed pattern with flat bottom and cover and mild steel chromium plated or aluminium plated or aliminished hinging device fixed in repair.

S&F for vitreous china wash down water closet pan(pedestal pattern) white (excluding fixing bolts, flushing cistern and floor pipe) fixing in repairs EWC.

S&F in repair vitreous china washbasin, white, flat back, size 550 x 400mm, including brackets & incl 32mm bore waste fitting brass, CP for glazed ware basinetc with long screwed shanks and fly-nuts flange end bedded in red lead cement and other end fixed including pedastal for washbasin complete all as specified.

S&F for brass chromium plated shower rose 125mm fixed in repair.

S&F for ball valve high pressure of PTMT withepoxy coated Aluminum rod & high density plastic ball screwed for iron pipe or brass ferrule and fixed in repair 20mm bore.

M&L for stainless steel sink with draining board made of 1.00mm thick sheet for kitchen with plug , washer waste pipe cast iron cantilever bracket connecting union overall size 915mmx 460mm with bowl size 330mm x160mm.

S&F for acrylic shelf 450mm long and 100mm wide fixed over WHB of approved quality as per sample all as specified and directed Engr-in-charge

S&F for CP grating 150mm dia with centre hole all as specified and directed by Engr-in-Charge

S&F in repair PVC bathroom cabinet mirror size 350mm x 450mm complate all as specified and directed. (Make : Prayag or equvalent as approved by GE)

M&L for stainless steel plate rack of superior quality size 36" x 24" with not less than 8 kg all as specified .

S&F for rotational moulded polythene water storage tanks(cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I 500 ltr capacity incl dismantling water tanks and removing to store.

S&F for rotational moulded polythene water storage tanks(cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I 1000 ltr capacity incl dismantling water tanks and removing to store.

S&F for viterous china squartting pan orrisa pattern , size 580x 440mm white, integrated foot rest including connection to trap and to flush pipe, anti syphonic pipe etc complete making good to floor.

S&F for brass chromium plated tubular towel rail 20mm dia(D) type 60cm long between flanges complete.

S&F for 32mm dia waste pipe for WHB

S&F for brass chromium plated Jet to EWC

S&F for sheet glass ordinary quality and glazing with oil putty in square nexc 0.5 Sqm Each pane 3mm thick.

Ditto- all as per item No 44 above but Frosted glass glazing with oil putty in square nexc 0.5 Sqm Each pane.

Taking down chowkhat or frame with shutter(without taking off shutter from frame) exc 1.5Sqm and nexc 4Sqm.

-ditto -all as per item No 46 above but n -exc 1.5 Sqm Each.

Taking down shutters of any description exceeding 01 Sqm but not exceeding 2 Sqm each.

Resecuring or easing and adjustment without taking down the shutters of any description exc 1 Sq.m and n.exc 2 Sq.m each complete all as specified and as directed by the Engineer-in-Charge.

S&F for pressed steel frames,size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete ,as specified.

Ditto- all as per item No 50 above but size 125 X 60mm.

M&L for providing cement concrete type C-0 1:3:6 (12.5 mm graded agg) as for pressed steel chowkhats.

S&F for framed work as in doors or gate,coolers stand of angle or others section etc confirming to Fe 410-s .

S&F for solid PVC door frame of sixe 50mmx47mm made out of 5mm wood grain printed PVC Sheet reinforced with MS square tube in opening as per specification and drawing.

S&F for factory made soilid panel PVC Door shutter 30mm thick (Stype) consisting of frame made out MS frame shall be covered with heat moulded wood grain printed PVC 'C' channel having PVC sheet stripof 20mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheet for top rail, lock rail, & bottom rail; panelling of wood grain printed PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification and drawing.

S&F for 35mm thick Plain framed panelled shutter (two planel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of the rail and stile as per IS:1003(Part I), kiln sseasoned and chemically pressure treated 35mm thick.

S&F for 35mm thick Glazed and skeleton shutters open rebated and prepared to receive (glass) gauze (without sash bars) edges of framing plain chamfered or rounted fitted with cut and mitred beads for securing gauze (glass) etc size of members of shutters as specified 35mm thick 2nd class HW.

S&F for 35mm thick Flush shutters, solid core construction, with block board core and plywood face panels, if one face is covered with decorative face veneer with lipping / frame to match for CB 25mm thick partition wall, shelves etc.

S & F for steel window 1.25 mm thick box type (primer coated) ERW hollow P section of size 60mmx25mm single rebated comprises gauged skeleton shutter ERW sec 50mmx20mm and 1mm thick with two openable leaf consisting two Nos sash bars of T-section 20mmx3mm complete welded to frame with one verticle mulion of ERW box type T-section of size 60mmx25mm and 1.25mm thick incl cutting holes and making good dismantled portion PCC (1:2:4) type B-1 four Nos for Each window) including following fittings welded to frame shutter: - (a) Hold fast, 150mm long of 12mmx3mm made to shape-04 Nos per window. (b) Handle of z section 20mmx25mm, 100mm long 01 Nos per leaf (c) MS tower bolt 150mm long-2 Nos per leaf (d) z section 20mmx25mm, 100mm long stopper - 01 No per leaf (f) MS pintal hinges of size 75mmx12mm- 2 Nos per leaf (g) Fabrication & fixing arrangement as per Drg No CEJZ/TD-06/07. make/manufacture by 1. M/S Tee Pee enterprises, Amritsar 2. M/S Ram Fabricator 'P' ltd Panchkula. Note: wire mesh and painting shall be measured & paid separately under appropriate item.

-Dittio - all as per No 59 above but glazed .

S&F for framed work such as on grills ends of bars welded to frame quarol bars and similar work all as specified.

S&F for glavanised Mild steel wire cloth. 0.56mm nominal dia of wire and average width of aperature 1.18mm and fixed with tinned tacks or galvnaised wire staples.

S&F for butt hinges, medium weight cold rolled mild steel and fixed 100mm long.

S&F for aluminium anodised barrel tower bolts of extruded section and fixed 200mm long

S&F for aluminium handles cast type anodised 150mm long.

M&L for 300mm ordinary rat rail rod pattern spring including roller plate complete fixing mild steel spring.

S&F for aluminium alloy anodised sliding door with hasp staple(bolt type) and fixing clips of sheet cast or extruded section and fixing bolt and sliding bolts of extrudedsection or cast aluminium alloy and fixed 250mm long.

M&L for preparation of new surfaces of wood surface of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamelled paint over one coat of pink primer.

-ditto- all as per item No 68 above but two coats of synthetic enamelled paint of new surface of steel.

S&F for floor doors stoppers of aluminium alloy body and tenque anodised with hard drawn steel spring fixed in floor 150mm long.

Taking down curatain rods along with wooden pallmate laid on wall.

S&F in repair curtain rod made out of mild steel 25mm dia(outer dia) pipe having thickness 0.63mm , PVC coated and colour/pattern, over all dia 28 to 29 mm complete all as specified and directed, Make :- Aerolux/MEC.

S&F for plastic finial of 28 to 29mm bore, decorated type, of any colour/pattern, best quality to suit the curtain rod and fixed at the end of curtain rod with suitable adhesive complete all as specified and directed, Make:- Aerolux/MEC or VISTA

S&F for mild steel prepainted bracket to hold the curtain rod and fixed to wall(Concrete/brick masonry) with the help of 2 Nos 50mm long steel screws and rawl plug included drilling with electric drill and making good the disturbed surfaces complete all as specified and directed.

Demolition of cement concrete(unreinforced) of any description and in any position not otherwise specifically provided for

Dismantling brick tiles or terracing tiles sinlge layer on roofs.

Demolition of mud in roofs any thickness including plastering and leeping(whether full thickness removed or only a part there of)

M&L for wire brushing neat cement slurry with 3kg of cement per sq m at top and bottom of base coat and cleaning top surface all as specified

M &L for PCC 1:2:4 type B-1 as roof padding concrete to bring the extg slab in slope of 1:40. complete all as specified.

M&L for 15mm thick rendering on terrace, sides of parapet in cement mortar 1:4 with water proofing compound , finished even and fair.(Note water proofing compound will be measured and paid separately under other item.

Supply only integral water proofing compound.

M&L for priming surfaces and applying normal treatment (for moderate conditions) using bitumen primer @ .30 Kg/Sqm applied hot.

M&L for providing APP based polymeric membrane minimum weighing 3Kg/Sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt not less than 150 gms/Sqm ) land on after applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2Kg per Sqm by forced application complete all as specified.

M&L for 40mm thick brick tiles laid on mud mortar and joints grouted flush in cement mortar(1:3) mixed with 5% of crude oil by weight of cement on mud phuska.

-dittio - as per item No 84 above but except tiles.

M&L for flush pointing to brick laid flat or brick tiles in paving cement mortar in 1:3.

M&L for PCC 1:2:4 type B1 (using 20mm graded stone aggregate) in roof kerbs or mud stops, benching rounded or chamfered on edges complete.

Demolition of brick built in CM including all quoins arches pillars etc.

M&L for brick work with sub class 'B' bricks straight or curved in plam exc 6m mean radius built in cm 1:6.

Taking down cement plaster on brick or stone walls etc including raking out joints hacking for key scrubbing down with water etc.

M&L for 15mm thick plastering on fair faces of bricks or concrete surfaces finished even and smooth w/o using extra cement in cm1:6.

M&L for 5mm thick plastering on fair faces ofr concrete surfaces finished even and smooth w/o using extra cement in CM 1:3 on ceiling .

M&L for 15mm thick plastering on fair faces of bricks or concrete surfaces finished even and smooth w/o using extra cement in cm1:4.

M&L for preparing of new surface of plaster and applying three coats of white wash on ceiling.

M&L for preparing of new plastered surface and applying two coats cement base paints on walls.

M&L for preparation of new surface of wall with one coat of Birla putty on plastering surface and applying two coat of oil bound distemper on walls.

M&L for complete removal of existing treatment and applying two coats of cement base paint of walls.

M&L for complete removal of existing treatment and applying two coats of oil bound distemper over one coat of Birla putty on the surface of walls.

M&L for preparation of old painted wooden surfaces of any description not other wise described over 10cm width or girth and applying one coat (finishing coat) of synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge

Taking down eaves gutter and rain water pipes (of any size and patern), incl all fittings and, heads, shoes, bends, swan-necks, etc incl cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accesaries)

S&F for 110 mm PVC (SWR) Rain water pipes single socketed in any length with rubber ring joints fixed to walls.

S & F for PVC (SWR) bends 110 mm dia

Demolition on reinforced cement concrete of any description and in any position not otherwise specficially provided for.

M&L for reinforced Cement Concrete type B1 1:2:4 (nominal mix ) (using 20 mm graded stone aggregate) in Cooking platform, RCC self etc.

M& L for use and waste rough finished flat Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping).

S&F for mild steel TMT bars 10mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips quality.

M&L for pre-cast cement concrete 1:2:4 cover slab for manholes etc using 20mm graded stone aggregate. Set in cement 1:4.

Dismantling asbestos cement corrugated sheet in roof covering all as specified.

S&F for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

S&F for framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc., n exc 10 kg each brackets, conforming to Fe 410-0 or Fe 310-0 all as specified and as directed by Engr-in-Charge.

M&L for Endura chequrred cement concrete tiles with grey cement & pigment 25cmx 25cmx 25mm thick, set, jointed & pointed in neat cement slurry , in floors over and incl 20mm thick screed in cement mortar 1:6

Material and labour for cleaning and removing sludge/soil mud, etc at blockage of sewage pipe ling of 150mm bore by rodding manually from both side at manhole/gully trap of any depth/size and flushing with water till clear flow of water is observed at the lines, complete all as specified and directed.

M&L for cutting chases, pinning in, making good to facing where reqd and pointing in CM 1:3 to ends of edges of landing etc and cutting chases for concealed water tubing and making good cutting exc 10 cm but n.exc 20 cm girth.

Taking down carefully point wiring copper/ aluminium (light, fan, socket, power) complete including switches, ceiling roses , pendants, regulators , sockets etc and removing materials to store and making good the disturbed surfaces of walls, floors etc Complete all as specified & directed by Engineer in Charge.

Taking down service /sub main wire of any size fixed in any position , complete all as specified and directed by Engineer in charge.

M & L for point wiring with PVC (FRLS) unsheathed, fire resistance, stranded copper conductor of size 1.5 sqmm (nominal cross sectional area ) single core cable in and including concealed (surface only on roof & colomns) wiring incl PVC conduit medium grade, ISI marked, 20 mm or higher dia complete with all accessories/fittings and sunkan MS boxes of thickness not less than 1.2 mm covered with modular plate and cover concealed in wall with screws & washers including unsheathed single core PVC (FRLS) insulated cable green in colour 1.5 sqmm stranded copper conductor as earth wire and connecting to earth dolly, complete all as specified & directed for the following.

One light point controlled by one switch 5 Amps one way.

One ceiling fan/Ex fan point controlled by one switch 5 Amps, one way

One call bell point controlled by one bell push

One 3/5 pin 5 Amps socket outlet on independent board

One 3 pin 5 Amps socket outlet on same board

M & L for point wiring with PVC (FRLS) unsheathed, fire resistance, stranded copper conductor of size 2.5 sqmm (nominal cross sectional area ) single core cable in and including rigid non metalic PVC conduit 20 mm dia or higher size "medium " grade ISI marked concealed (surface only on roof & colomns) complete with all accessories/fittings and MS box thickness not less than 1.2 mm covered with modular plate and cover concealed in wall with screws & washers including unsheathed single core PVC (FRLS) insulated cable green in colour 2.5 sqmm stranded copper conductor as earth wire and connecting to earth dolly, for one three /six pin 15/16 amps power socket controlled by one 15/16 amps switch complete all as specified & directed by Engineer in Charge.

Taking down and refixing of 18/20 Watt LED lighting fixture (4 Ft) incl connection from ceiling rose to connector complete all as specified and directed by Engr in Charge.

Taking down and refixing of 10 Watt LED tube lights complete all as specified and directed by Engr in Charge.

Taking down and refixing of 15 Watt LED surface mounted panel injection type complete all as specified and directed by Engr in Charge.

Taking down and refixing LED Bulk Head fitting 10 watt with pressure die cast aluminium housing for multiple application IP 65 protected complete all as specified and directed by Engr in Charge.

Taking down and refixing LED security light fittng 25 watt made up of pressure die cast housing with toughened glass complete all as specified and directed by Engr in Charge.

S&F for switch Modular 6A single pole, one way, 1 module complete all as specified and as directed

S&F for switch Modular 16A single pole, one way, 1 module complete all as specified and as directed.

S&F for socket, 6A - 2/3 pin combined 2 module complete all as specified and as directed

S&F for socket 6A/16A - 2/3 pin combined 2 module complete all as specified and as directed.

Supply and fixing for ceiling rose surface bakelite 65x 50mm 2 to 3 terminal, polycarbonate /pvc/ isolated body complete all as specified and directed by Engr in Charge

Supply and fix for electronic Bell 230 Volts single pole Ding dong type complete all as specified and directed by Engr in Charge

Supply and fix for bell push 230 Volts complete all as specified and directed by Engr in Charge

Supply and fixing for rotary stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc.as reqd complete all as specified and directed by Engr in Charge

S&F for modular White cover plate with frame,6 module complete all as specified and as directed

S&F for modular White cover plate with frame,4 module complete all as specified and as directed

S&F for modular White cover plate with frame,3 module complete all as specified and as directed

S&F for modular White cover plate with frame,2 module complete all as specified and as directed

S&F for modular Metal flush box 6 module complete all as specified and as directed

S&F for modular Metal flush box 4 module complete all as specified and as directed

S&F for modular Metal flush box 3 module complete all as specified and as directed

S&F for modular Metal flush box 2 module complete all as specified and as directed

M & L for sub main wiring with two run of 4 Sqmm (nominal cross sectional area ) of single core unsheathed PVC (FRLS) insulated cables 1100 Volts grade multi stranded copper conductor drawn through & including non metallic rigid PVC conduit of size 19/20 mm or higher dia with & including necessary conduit accessories concealed/surface only on roof & colomn) type including one run of 4 Sqmm stranded copper conductor PVC (FRLS) insulated cable as earth wire connected to common earth dolly complete all as specified & directed by Engineer-In-charge. Note:- Three running of wire shall be measured in one unit.

M & L for sub main wiring with two run of 6 Sqmm (nominal cross sectional area ) of single core unsheathed PVC (FRLS) insulated cables 1100 Volts grade multi stranded copper conductor drawn through & including non metallic rigid PVC conduit of size 19/20 mm or higher dia with & including necessary conduit accessories concealed/surface only on roof & colomn) type including one run of 6 Sqmm stranded copper conductor PVC (FRLS) insulated cable as earth wire connected to common earth dolly complete all as specified & directed by Engineer-In-charge. Note:- Three running of wire shall be measured in one unit.

Taking down ceiling fan, sealing cable end, dismantiling blades and removing fan and blades to store complete all as specified and directed by Engr in Charge

M & L for cleaning thoroughly and spray painting of ceiling fans with super enameled paint (white) etc complete all as specified and directed by Engr in Charge

M & L for Re-fixing ceiling fan at the existing site / rooms and connected with 23/0.0076 three core PVC flexible cable from ceiling rose to fan etc complete all as specified and directed by Engr in Charge

Supply and fixing for exhaust fan 300 mm sweep 230/240 volts, AC single phase with louwer complete all as specified & directed by Engineer-in- charge.

S& F for single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps, replastring to match with existing surface etc complete all as specified & directed by Engineer-in-charge.

Supply and fixing for factory made sheet metal enclosures SPN 12 way double door 240 v with 200 Amps rated bus bar for DB,s suitable for having MCB / Isolator flush with wall complete all as specified and directed by Engr in Charge

S&F for MCB, single pole 240 Volts 5 to 30 Amps complete all as specified & directed by Engineer-In-charge.

S&F for single pole and neutral 240 Volts 40 Amps complete all as specified & directed by Engineer-In-charge.

M&L for earthing complete with galvanised steel earth plate electrode 60cm X 60 cm X 6.3mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level with the top edge of electrode not less than 1.5 mtr below normal ground level connected to galvanised earth lead wire 4mm dia means of bolts, nuts,check nuts and washers of galvanised iron and GI lead protected with protection pipe of GI light grade 15mm dia upto 3mtr above ground level along poles fixed with two clamps of 25mm 3mm flat iron and connected to running earth wire at top of poles and watering pipe 20mm bore of GI medium grade all as shown in electrical plate No 3 of SSR Part-I 2009 connected to earthing test point all as specified and direct and testing on completion including PCC 1:3:6 ) C-I cover and frame excavation and earth work etc complete all as specified in elect plate No 3 of SSR Part -I 2009 Note :- PCC Chamber shall be constructed at least 1.50 mtr away from on the earth pit electrode and pipe for watering shall be provided in slanting manner complete all as specified and directed by Engr in Charge.

ANUJ ABROL CONTRACTOR

PK ENTERPRISES

NEWTON ENGINEERS

M/S Satguru enterprises