GENERAL RM 2024 25 RC 2 Phase 1 Zone I one year Running contract for various PWD Roads under Roads Section Kottayam in Kottayam district 23 Road Stretches for a length of 37. 857 Km civil work General Civil Work

Amount

Appendix A - Reactive maintenance

OD171767/2024-2025:Conducting and reporting routine inspections for the entire length of project Road at a frequency of 7 days through out the agreement period of the running contract as directed by the departmental officer at site Additional RI may be required in response to reports or complaints from the police, other authorities and the public as a result of major incidents, typhoon or flooding damages etc. and are not measurable/ payable. A proportion of the RI should be carried out either during or immediately following a period of wet weather.

OD167912/2024-2025:Providing and fixing New Non-retro-reflectorised Vinyl sign using Vinyl Printed sheeting fixed over existing DLP board for Running contract work with with 1 years warranty manufactured with area not exceeding 0.9 sqm, after clearing old sticker from surface

OD168920/2024-2025:Providing and fixing of DLP board for Running contract work with Non-retro-reflectorized Vinyl sign with 1 years warranty manufactured Vinyl Printed sheeting fixed over aluminum sheeting 2 mm thick/ aluminium composite material sheeting 4 mm thick with area not exceeding 0.9 sqm, with suitable back supporting frame of MS angle 40x40x6 and supported on GI pipe pole 50mm NB confirming to IS 1239 firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete min size 45 cm x 45 cm x 60 cm, 60 cm below ground level including painting all exposed surface with 2 coats of epoxy painting over epoxy primer and as per approved drawing and clause 801 including lettering symbols etc

OD301711/2024-2025:Scarifying the existing bituminous road surface to a depth of 50 mm and then levelling ground with scarified material mixed with water at OMC and then by rolling so as to achieve minimum density by Mechanical Means <br>

4.1.B.2:Construction of granular sub-base by providing graded material, spreading in uniform layers with a motor grader on a prepared surface, mixing by mix in-place method with rotavator at OMC, and compacting with a vibratory roller to achieve the desired density, complete as per clause 401. Grading-VI - For sub-base cum drainage layer - Mix in Place Method

4.12:Providing, laying, spreading and compacting graded stone aggregate to Wet Mix Macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density.

5.1.a:Providing and applying primer coat with bitumen emulsion ( SS) on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.70 - 1.0 kg/sqm using mechanical means.

5.2.a:Providing and applying tack coat with bitumen emulsion( RS) using emulsion pressure distributor at the rate of 0.20 - 0.30 kg per sqm on the prepared bituminous surface cleaned with mechanical broom.

5.3.2.a:Providing and laying bituminous macadam with 80-100 TPH hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading premixed with a bituminous binder (VG 30), transported to the site, laid over a previously prepared surface with paver finisher to the required grade, level, and alignment and rolled as per clauses 501.6 and 501.7 to achieve the desired compaction For Grading II - (19 mm nominal size)

5.6.2.a:Providing and laying bituminous concrete with 80-100 TPH hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with a bituminous binder( NRMB) @ 5.4 percent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level, and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause No. 507 complete in all respects For Grading - II (13.2 mm Nominal Size)

12.8.B:Plain/Reinforced Cement Concrete in Open Foundation complete as per Drawing and Technical Specifications PCC Grade M20 (Without formwork)

12.4:Plain cement concrete 1:3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days.

Appendix B - Premonsoon works

55.15:Refurbishment of existing signboardsRefurbishment of existing signboards of all size except gantry mounted ones to their original reflectivity & position by removing obstructions like overgrowth vegitation etc ,if any,washing the signboards with water & soap solution to remove all dirt, oil etc. , correcting any dislocations including minor repairs, replacement of lost nut and bolts etc complete.

OD159430/2024-2025:Engaging man mazdoor for clearing drain, culvert and other miscellaneous items

2.2:Clearing grass and removal of rubbish up to a distance of 50 metres outside the periphery of the area

OD159431/2024-2025:Engaging Tipper 5.5 cum capacity from conveying the silt removed

OD170058/2024-2025:Engaging wood cutter with machine for Cutting of trees including cutting of trunks and removal of stumps, roots, etc/ Cutting down Unsafe branches of trees

OD167035/2024-2025:Supplying Hydraulic Excavator with Driver and fuel

OD159437/2024-2025:Filling up of potholes with Bituminous Readymix compound (25 kg bag) and compacting by ramming to get a compact surface including of cost of materials laying charges transportation to site. etc complete rate is arrived for a bag of 25 kg.

OD159439/2024-2025:Hire charges of Crane with Operator and fuel

Appendix C - Proactive maintenance

3.6:Excavation for roadwork in soil with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location within all lifts and lead upto 1000m

4.1.B.1:Construction of granular sub-base by providing graded material, spreading in uniform layers with a motor grader on a prepared surface, mixing by mix in-place method with rotavator at OMC, and compacting with a vibratory roller to achieve the desired density, complete as per clause 401. Grading-V - For sub-base cum drainage layer - Mix in Place Method

55.22:Supplying and laying interlocking tile 100 mm or nearest size thickness, minimum strength M 40 including providing a layer of 6 mm aggregate for 5 cm thickness, then laying interlock cobbles in lines and levels as per the directions of the departmental officers at site inclusive of all cost & conveyance charges etc.; complete.

4.12:Providing, laying, spreading and compacting graded stone aggregate to Wet Mix Macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density.

OD167041/2024-2025:Removal of all failed material, trimming of completed excavation to provide firm vertical faces, cleaning of surface, painting of tack coat on the sides and base of excavation as per clause 503, back filling the pot holes with hot bituminous material as per clause 504, compacting trimming and finishing the surface to from a smooth continuous surface, all as per clause 3004. 2 Filling Port holes and Patch Repairs with Bituminous concrete For grading II- 13 mm (Nominal size) Material with bitume VG-30 @ 5.4% by weight of total mix (Modified 10.5.1b)

55.2:Supplying and stacking 12mm hard blue granite broken stone in standard heaps for measurement(IRC 3.2.1.a)

55.4:Supplying and stacking 36mm size hard broken stone in standard heaps for measurement.

55.8.a:Filling up pot holes (cut and formed to regular shapes and all loose and defective materials removed) after supplying a prime coat of hot bitumen using 36mm departmental broken stone and compacting with power roller to get a compact surface.

55.9.a:Filling up pot holes (cut and formed to regular shapes and all loose and defective materials removed) after supplying a prime coat of hot bitumen using 12mm departmental broken stone and compacting with power roller to get a compact surface.

5.3.2.a:Providing and laying bituminous macadam with 80-100 TPH hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading premixed with a bituminous binder (VG 30), transported to the site, laid over a previously prepared surface with paver finisher to the required grade, level, and alignment and rolled as per clauses 501.6 and 501.7 to achieve the desired compaction For Grading II - (19 mm nominal size)

5.2.a:Providing and applying tack coat with bitumen emulsion( RS) using emulsion pressure distributor at the rate of 0.20 - 0.30 kg per sqm on the prepared bituminous surface cleaned with mechanical broom.

OD159419/2024-2025:Close Graded Premix Surfacing/Mixed Seal Surfacing :- Case I, Type - A - Manual means Providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness composed of 11.2 mm to 0.09 mm (Type-A) aggregates using penetration grade bitumen using VG 30 to the required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a Smooth wheeled roller 8-10 tonne capacity, and finishing to required level and grade

12.4:Plain cement concrete 1:3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days.

12.8.B.1:Plain/Reinforced Cement Concrete in Open Foundation complete as per Drawing and Technical Specifications PCC Grade M20

8.15:Supplying and installation of delineator (Roadway indicators) posts 80- 100cm high above ground level, pained black, and white in 15 cm wide strips, fitted with min. 80 x 100 mm rectangular or 75 mm dia circular retro reflectorized panels at the top with minimum visibility of 300m with provisions to prevent edge lifting and vandalisam, and conforming to clause 806 , IRC-79 and the drawings including fixing to ground (The deleniator shall be of approved type as per specification)

8.13:Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads on Bituminous Surface @ 250 gms per sqm area, the thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35. The finished surface to be level, uniform, and free from streaks and holes.

55.10.1:Providing and erecting retro-reflectorised Object Hazard Marker 300mm x 900mm Providing and erecting retro-reflectorised Object Hazard Marker sign with 07 years warranty, manufactured as per IRC 67 USING Type IV ASTM D 4956-09 micro prismatic retro reflective sheeting fixed over aluminium sheetig, 2 mm thick / aluminium composit material sheeting 4 mm thick with suitable back support frame and supported on a mild steel angle iron post 75mmx75mmx6mm, firmly fixed 30cm above ground level by means of properly designed foundation with M 15 grade cement concrete 30cmx30x45cm, 45cm below ground level including painting all non-reflective faces with epoxy paint 2 coats over epoxy primer as per approved drawing and clause 801.300 mm x 900 mm

OD177706/2024-2025:Providing,laying and rolling of Close Graded Premix Surfacing material of 40mm thickness composed of 11.2 mm to 0.09 mm (Type-A) aggregates using viscosity grade bitumen using (VG 30 )to the required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable HMP of appropraiate capacity not less than 75 tonnes/hour, transporting hot mi to work site, laying with hydrostatic paver finisher with sensor control to required level, grade and alignment, rolling with a Smooth wheeled roller 8-10 tonne capacity, and finishing to required level and grade

12.8.1.C.1:Plain/Reinforced Cement Concrete in Open Foundation complete as per Drawing and Technical Specifications RCC Grade M20 - Using Concrete Mixer

12.40:Supply, Fitting and Placing un- coated HYSD bar Reinforcement in Foundation complete as per Drawing and Technical Specifications

EMERGENCY WORK

OD159426/2024-2025:Engaging man mazdoor for clearing drain, culvert and other miscellaneous items

OD170057/2024-2025:Engaging wood cutter with machine for Cutting of trees including cutting of trunks and removal of stumps, roots, etc/ Cutting down Unsafe branches of trees

OD159438/2024-2025:Supplying Hydraulic Excavator with Driver and fuel

8.45:Provision of metal drum/empty bitumen drum delineator, 300 mm in diameter, 800 mm high, filled with earth for stability, painted in circumferential strips of alternate black and white 100 mm wide fitted with reflectors 3 Nos of 7.5 cm dia, all as per IRC:SP:55-2001

OD159440/2024-2025:Hire charges of Crane with Operator and fuel

OD170056/2024-2025:Providing and Displaying Information Board (Printed Flex of size 1.20m x 0.90 m ) for road diversion during emergency like Flood, landslide, etc. rate includes cost of material, transportation and fixing, any unforseen expences.

Bidder Name

Joshy Chandy