AS and AS TO FLOORING IN ADMIN BUILDING P40 GROUND FLOOR AND STAIRCASE EAST SIDE AT INS CIRCARS AS and AS TO COMNETCEN HQ ENC BLDG P45 AS and AS CIO OFFICE BLDG NO T 07 HQ ENC PROVISION OF PAVED AREA FOR JOC EAST T 3 BLDG AS and AS TO CLO OFF

Amount

Demolition of Unreinforced Cement Concrete in ground floors and Pavings not exceeding 15cm thick [below or above ground level] and removing rubbish to out side MD land complete all as specified and as directed.

M&L for 75 mm thick PCC 1:4:8 type D-2 (40mm graded aggregate) as in sub base of floor / pavings etc complete all as specified and as directed.

S&F Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over Screed bed or bedding layer of cement mortar 1:4, 20 mm thick for laying floor finishes complete all as specified and as directed. Make : Somany / Kajaria / Orient Bell / Cera / Asian

S&F Glazed coloured ceramic tiles in vertical surface 350 x 250 x 7 mm/ 450 x 350 x 7 mm thick (Concept pattern Tiles), set and jointed in neat cement slurry and pointed in white or cloured cement over and including 10mm thick backing coat CM of 1:3 complete all as specified and as directed. Note : Rate includes for cutting for offsets etc Make : Somany / Kajaria / Orient Bell / Cera / Asian set and jointed in neat

M&L Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry as in floors including screed bed or bedding layer in cement mortar 1:4, 20 mm thick complete all as specified and as directed. Make : Bharat Tiles & Marble Pvt Ltd / National Tiles & Industries Pvt Ltd / Nitco Tiles Pvt Ltd / Nimco Tiles / Metro Tiles Bombay / Vitco Tiles Bombay / Mehtab Tiles

Complete removal of existing treatment on walls and removing rubbish to out side MD land complete all as specified and as directed.

M&L for preparing surfaces of walls considered in item No. 06 above and applying three coats of white wash complete all as specified and as directed.

S & F Stainless steel railing at Entrance of Ramp and at Stair case area confirming to Grade 304 SG including necessary fixing arrangements, welding etc, complete all as specified and as directed.

M&L for green marble 20 mm thick as in flooring laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including screed bed or bedding layer in cement mortar 1:6, 15 mm thick or complete all as specified and as directed

M&L for green marble 10 mm to 12 mm thick as in skirting / border etc laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including cutting and polishing, rendering 10 mm thick on fair faces of brick work or concrete surfaces as in backing coat in cement mortar 1:4 for complete all as specified and as directed

S&F Aluminium frame for doors, windows, ventilators, shutters, fixed partitions etc., with one or more rebates with powder coating of minimum 50 micron thick including joining cleat for fixing etc., complete all as specified and as directed. Make : Jindal / Indal / Hindalco

S&F Sheet glass 5.5 mm thick, ordinary quality and glazing with and including anodised aluminium snap beading or rubber / reopren bead in squares exceeding 0.5Sq.m in each pane, complete all as specified. Make: HINDUSTAN PILKINGTON GLASS / MODIGUARD.

M&L for 12 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, with 6mm thick teakwood lipping, fixed with screws to timber frame work in repairs complete all as specified and as directed. Make : Anchor / Novopan / Deco Board / Bhutan Board / Kitply / Eco Board / Archidlam / Asis / Greenply Industries

S&F Aluminium extruded section body Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and as directed. Make : Godrej / Everite / Priya

S & F [ISI marked] 125 mm long mild steel med wt cold rolled steel Butt hinges complete all as specified and as directed

S & F 15 mm bore Galvanized Steel tubes, medium grade (ISI Marked) for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors / trenches and testing complete all as specified and as directed. Make : Prakash / Tata / Zenith / Jindal

S&F for Stops valves, cast copper alloy, chromium plated fancy type with capstan head screwed down, high pressure, screwed both ends for 15 mm bore iron pipe or for unions in repairs complete all as specified and as directed. Make : M/s Hindware / Orient / Seiko / Dripless

M/L for PVC(SWR) Plain floor trap 75mm dia outlet with grating incl jointing with solvent cement fixed in cement concrete B1 (1:2:4) complete all as specified and as directed. Make : Supreme / Prince / Finolex

S &F 75 mm bore PVC (SWR) soil, waste and vent pipes single socked in any length with rubber ring joints fixed to walls / laid in floors complete all as specified and as directed. Make : Supreme / Prince / Finolex

S&F Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over Screed bed or bedding layer of cement mortar 1:4, 15 mm thick for laying floor finishes complete all as specified and as directed. Make : Somany / Kajaria / Orient Bell / Cera / Asian

M&L for providing PCC type B-0, 1:2:4 (using 12.5 mm graded granite stone aggregates) as in lintels upto 1.5m clear span, cills, steps; eismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed.

M&L for MS in framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, frame balusters, walk ways, railings, framework for water tanks and similar works confirming to Fe 290 Gde-E-165 complete all as specified and directed.

M&L for preparing new or previously untreated steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc primer complete all as specified and as directed. Make :M/s. Asian Paints [Apcolite], M/s. Berger Paints [Luxol], Jenson & Nicholson [Brolac] all are 1st quality.

Taking down Cement Plaster of any description on brick or stone walls or concrete surfaces including raking out joints, hacking for key, scrubbing down with water etc and removal of rubbish to the out side MD land complete all as specified and as directed.

M&L for rendering 10mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished even and smooth without using extra cement complete all as specified and as directed.

M & L for applying wall care putty on walls / ceilings two coats and sand papering to obtain a smooth surface including making good any undulations on the surfaces complete all as specified and as directed. Make for Putty : JK white cement / Birla wall care / Jenson & Nicholson

M&L for preparing plastered surfaces of internal walls / ceilings and applying two coats of oil bound distemper over one coat of alkali resistant primer complete all as specified and as directed. Make : Asian / Nerolac / Berger ( All 1st quality)

M&L for GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequel flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre / intermediate channel 0.9mm thick having two equel flanges of 15mm each and web of 45mm suspended from soffit and approximate 900mm centre to centre with GI cleat and steel expansion fastners with and including ceiling section (n.exc. 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre . Hangers 6 mm dia GI (upto 1200 mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size 60 mm long and expansion holdfastners 12.5mm dia, 40mm long, including Gypsum Board 12mm thick in ceiling fixed with screw as pe manufacturers instructions finished with two coats of Oil bound distemper over one coat of primer over putty [ any number of coats] and sand papering to obtain smooth finish including taking down the existing old ceiling with frame complete all as specified and as directed. Make :(I) Make of Gypsum Board : M/s India Gypsum, M/s Saint Gobain (ii) Make of Putty : JK white cement / Birla wall care / Jenson & Nicholson

Providing and injecting chemical emulsion for Post Constructional Anti termite Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and as directed.

M&L for ATT At points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre / hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and as directed.

Taking down Chowkats or frames exc 1.5 sq. m but n exc 4 sq. m each with shutters (without taking off shutters from the frame) complete all as specified and as directed.

S & F Anodised Aluminium window and ventilator shutters, side hung/siding type without sash bar aluminum section weighing 0.55 Kg/ RM including necessary joining cleats, glazing clips, rubber packing, sliding rollers, anodised aluminum snap beading, screws, anodised aluminum fittings such as peg stays 150 mm long (1 No.), hinges type B-21 100 mm long (2 Nos.), suitable handle (1 No.) if any complete all as specified and as directed. Make: HINDALCO / INDALCO/JINDAL

S&F Sheet glass 5.5 mm thick, ordinary quality and glazing with and including anodised aluminium snap beading or rubber / reopren bead in squares not exceeding 0.5Sq.m in each pane, complete all as specified. Make: HINDUSTAN PILKINGTON GLASS / MODIGUARD.

S&F 7 mm thick aluninium grills of make " Decogrill" model DG 104 with surrounded by aluminum channel complete all as specified and as directed.

S&F Factory Made second class hard wood plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed.

S&F 35 mm Factory made Flush shutters[ISI marked], solid core construction, with block board core and plywood face panels, commercial type on both sides covered with 0.9 mm thick decorative lamination on both sides complete all as specified and as directed.

S & F 125mm long medium weight Stainless Steel Butt hinges complete all as specified and as directed.

S & F 150 mm long [ISI marked] Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and as directed.

S & F Aluminium anodised barrel Tower Bolt (ISI Marked) of size 150 mm long of extruded section complete all as specified and as directed.

S & F 300 mm long [ISI marked] Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy, complete all as specified and as directed.

M&L for preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint (ordinary tint) over a coat of pink primer complete all as specified and as directed. Make :M/s. Asian Paints [Apcolite], M/s. Berger Paints [Luxol], Jenson & Nicholson [Brolac] all are 1st quality.

Demolition of brick work or stone / boulder masonry, built in cement mortar including all quoins, pillars etc., and disposal off unserviceable materials, debris to out side MD land complete all as specified and as directed.

Demolition of cement Concrete of any description and in any position not otherwise specifically provided for and separation of serviceable materials from the unserviceable, stacking the serviceable materials within 100 M and removing rubbish to out side MD land complete all as specified and as directed.

M & L for 25 mm thick, PCC 1:2:4, Type B0, using (12.5mm graded aggregate) as in sub base of flooring complete all as specified and as directed.

M&L for Vitrified ceramic tiles 10 mm thick (Square/ Rectangular) polished, Dark shade, area of each tile exceeding 0.36 Sq.M and not exceeding 0.36 Sq. M, as in floors etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match over and including screed bed or bedding layer in cement mortar 1:4, 15 mm thick for laying floor finishes complete all as specified and as directed. Make : Johnson / Nitco / Asian Granito / Varmora

Rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:3 for backing of Dado/ Skirting complete all as specified and as directed.

M & L for Roof tiles, Mangalore pattern, interlocking at side joints, laid dry including Dismantling Mangalore pattern roofing tiles with ceiling tiles or slate roofing complete all as specified and as directed.

M & L for Roof tiles, Mangalore pattern, interlocking at side joints, laid dry but except tiles complete all as specified and directed.

M & L for second class hard wood clean sawn battens at 300 mm centres of sectional area exceeding 5 Sq.cm and not exceeding 15 Sq.cm including cdismantling of old battens complete all as specified and as directed.

M & L for Ridge or hip tiles to suit Mangalore pattern of roofing tiles, bedded and jointed and jointed in cement mortar 1:6, complete all as specified and as directed.

M & L for preparing surfaces of of tiles or tile battens any space or any size and new or old of any description and girth, not otherwise described, wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with creosote oil complete all as specified and as directed.

Surface excavation not exceeding 30cm and averaging 25 cm deep and getting out and getting out in soft / loose soil complete all as specified and as directed.

Excavation in trenches, not exceeding 1.5m wide and not exceeding 1.5m depth for foundation, etc., and getting out in Soft / Loose soil complete all as specified and as directed.

Material and Labour for Brick work with fly ash bricks, straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:4 complete all as specified and as directed.

M & L for hardcore of gauge not exceeding 63 mm of broken stone, deposited, spread and leveled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

M&L for 100 mm thick Cement concrete type B1, 1:2:4 (using 20 mm graded stone aggregate) in flooring / hard standing finished even and fair complete all as specified and as directed.

M & L for Sand filling in floors or in foundations including watering and consolidation complete all as specified and as directed.

S&F machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thick, M-35 Grade finished with grey cement and pigment complete all as specified and as directed. Make : Ultra, Eurocon, Duracrete, Mehatab as approved by GE.

M&L for Rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished even and smooth without using extra cement complete all as specified and as directed.

M&L for Precast cement concrete 1:2:4, type B1 (Using 20 mm graded stone aggregate) as in landings, cover slabs (for manholes etc.) shelves and similar articles with plain faces and set in cement mortar 1:4 complete all as specified and as directed.

M&L for Mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and as directed.

M&L for PCC 1:3:6 Type C2 ( using 40mm graded aggregates) as in bed concrete for foundation etc complete all as specified and as directed.

M&L for Providing, cement concrete 1:2:4 type B-0 (Using 12.50mm Graded stone aggregate) in roof kerbs or mud stops, rounded or chamfered on edges, coping, surface channels complete all as specified and directed.

Removing Excavated spoil to outside MD land depositing where directed at a level not exceeding 1.50m above the starting point complete all as specified and as directed.

M&L for PCC 1:4:8, Type D2 ( using 40mm graded aggregates) as in bed concrete for foundation etc complete all as specified and as directed.

M&L for Reinforced Cement Concrete (Nominal Mix) Type A1 1:11/2:3 (using 20 mm graded stone aggregate) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed.

M&L for Reinforced Cement Concrete (Nominal Mix) Type A1 1:11/2:3 (using 20 mm graded stone aggregate) as in Columns, pillars, piers, posts and struts complete all as specified and as directed.

M&L for Mild steel TMT bars 5 to 10 mm dia., and over cut to length, bent to shape required, as in stirrups, spacers and binders including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and as directed.

M&L Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick with hard dense soil complete all as specified and directed

Removing Excavated soils to a distance not exceeding 50 M and and depositing where directed at a level not exceeding 1.5m above from the starting point complete all as specified and as directed.

M&L for preparation of new wall surfaces and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and as directed. Make : Super-Snocem / Durocem / Aquacem complete all as specified and directed

Use and waste of rough finished flat Form work to sides of concrete foundations, rafts, plinth beams and similar work, vertical or batter complete all as specified and as directed.

Use and waste of Fair finished flat Form work to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and as directed.

M&L for 35mm thick precast cement concrete (1:2:4) type B-0, using 12.5mm graded stone aggregates in louvers and jallies, including all mouldings and set in cement mortar (1:4) complete all as specified and as directed.

S&F Sheet glass 4.8 mm thick, ordinary quality and glazing with and including anodised aluminium snap beading or rubber / reopren bead in squares not exceeding 0.5Sq.m in each pane, complete all as specified. Make: HINDUSTAN PILKINGTON GLASS / MODIGUARD.

M & L 12 mm thick prelaminated particle board, exterior grade, both sides with decorative choice lamination fixed with screws to timber frame work in cup board shutters or fixed to aluminum frame work with rubber beading etc. complete all as specified and as directed. Make : Anchor / Novopan / Deco Board / Bhutan Board / Kitply / Eco Board / Archidlam / Asis / Greenply Industries

Material and Labour for Brick work with fly ash bricks, straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:6complete all as specified and as directed.

Material and Labour for Brick work with fly ash bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 including provision of 2Nos 8mm dia TMT bars at every fourth course complete all as specified and as directed

S&F in repairs kitchen Sink with drainage board made of stainless steel 1 mm thick with plugs, washers and wastes including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm and bowl size 405 mm x 355 mm x 178 mm complete all as specified and as directed. MAKE : M/S BLUE STAR MODEL NO. BSSBSD-52 / M/S JAYNA / NIRALI

M & L for prepolished Granite (of any type) work 20 mm thick machine cut (table rubbed and polished) in floorings, steps, jambs, pillars, window-cills, cooking platforms, skirting / dado and the like including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite laid over backing coat in cement mortar 1:4, 10 mm thick and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of stone complete all as specified and as directed.

S & F reinforcement using TMT steel bars of 6mm to 8mm dia, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

S&F for 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as specified and as directed.

S&F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and directed.

M&L for 100 mm thick PCC 1:2:4 type B-1 (20mm graded aggregate) as in sub base of floor / pavings etc complete all as specified and as directed.

S&F machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80mm thick, M-35 Grade finished with grey cement and pigment complete all as specified and as directed. Make : Ultra, Eurocon, Duracrete, Mehatab as approved by GE.

M&L for rendering 10mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished even and smooth without using extra cement complete all as specified and as directed.

M&L for RCC 1:11/2:3, type A-1, using 20mm graded stone aggregates as in beams, lintels and the like complete all as specified and as directed.

Use and waste of Fair finished flat Form work to sides of beams , lintels etc., complete all as specified and as directed.

M&L for Rendering 5 mm thick on fair faces of concrete surfaces in ceilings in cement mortar 1:3 and finished even and smooth without using extra cement complete all as specified and as directed.

M & L for preparing the new plastered / untreated surfaces of walls/ ceilings and applying two coats of weather proof Acrylic Exterior emulsion paint of approved make and shade over a coat of approved primer as recommended by the manufacturer complete all as specified and as directed. Make : (i) Weather coat paint :Apex ULTIMA from Asian Paints / All Guard from Berger / Weather Shield Max Exterior Acrylic from ICI Dulux

S&F mild steel angles, bars, flats etc., as in supports for stiffening of fencing, wall ties, hold fasts, clamps and similar small articles conforming to Fe 410-O or Fe 310-O complete all as specified and as directed.

Supply anf Fix in opening Factory made solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube manufactured as per SSR Part I specifications and drawing complete all as specified and as directed.

S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per SSR specification and as directed

S & F PVC ventilator with frame work, made with Multi Chamber Hollow PVC Section of size 40 X 46mm [DWUF 405], 50% of portion is fixed with 4mm thick pin headed / frosted glass and remaining portion is covered with Stainless Steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with Stainless steel wire staples fixed to the frame in the lower section using extruded PVC Section of size 9 X 14.5mm [GL-19] with EPDM gasket [SPL - 003], Ventilator Center Mullion shall be of [DWUF - 406] with EPDM gasket is used GL-19is fixed to the 3 sides of DWUF-405 and to one side of DWUF-406 above the centre mullion glass panels with aluminium lower set is fixed to the frame DWUF-405 on the top of the ventilator for the glass DWUF-406 corners shall be metred cut welded, jointed with 12mm MS rods /guard bars duly painted and necessary fixtures complete all as specified and as directed. Note :- The rate quoted shall be deemed to inclussive of glass, wiremesh and guard bars Make for Item No. 100, 101 and 102 : Syntex / Nandi / Rajashri plasticwood

S & F Aluminium anodised barrel Tower Bolt (ISI Marked) of size 200 mm long of extruded section complete all as specified and as directed.

S & F 125 mm long extruded Aluminium alloy anodised Butt hinges [ISI marked] with galvanized mild steel hinge pin type B 21 complete all as specified and as directed.

S & F GI water tubing of 15 mm bore, medium grade (ISI Marked) conforming to IS - 1239 [Part - 1] including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors and connections and testing, complete all as specified and as directed. Make : Tata / Jindal / Prakash / Zenith

S & F GI water tubing of 20 mm bore, medium grade (ISI Marked) conforming to IS - 1239 [Part - 1] including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors and connections and testing, complete all as specified and as directed. Make : Tata / Jindal / Prakash / Zenith

S & F 25 mm bore Gun Metal, globe or Gate Valve with Iron wheel head Screwed both ends for Iron Pipe and fixed including taking down the existing valve complete all as specified and as directed. Make: Kirloskar / L & T / Upadhyay / Leader / Zolotto

S & F in repairs Vitreous China Ware Wash hand basin white, flat back, size 550 x 400 mm size with 15 mm bore pillar taps, Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe and 32 mm dia., Waste fittings, brass chromium plated for glazed ware sinks, wash basins etc., with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed including removing the existing Basin, pillar tap and brackets and fixing new brackets complete all as specified and as directed. Make of WHB : M/s. Parry ware or equivalent in M/s. Hindusthan Sanitary ware & Industries Ltd / M/s. Neycer Kemberg / M/s Cera ( All are 1st quality) Make of Pillar tap : M/s Hindware / Orient / Seiko / Dripless

S &F Brass chromium plated tubular towel rail, 20 mm dia , D type, 60 cm long between flanges complete all as specified and as directed.

S & F Vitreous Ware wash down water closet (Pedestal), white (ETWC) and 10 litres PVC capacity valve less, Syphonic action type, Flushing cistern, low level, white with inlet, ball valve, float and handle including brackets including PVC Flush pipe 32 mm dia., Plastic seat of same colour of WC, closed pattern with flat bottom, and cover and Mild steel chromium plated hinging device work up to 16th storey complete all as specified and as directed. Make of WC and Flushing cistern :M/s. Parry ware/ M/s. Hindusthan Sanitary ware & Industries Ltd / M/s. Neycer Kemberg / M/s Cera ( All are 1st quality)

S & F in repairs CP Hand Shower Health Faucet with 8mm dia, 1.00 m long flexible tube, wall hook, non return valve complete all as specified and as directed. Make : Jaquar ALD-CHR - 583 / Cera / Plumber

S & F 15 mm bore chromium plated bib tap of fancy type, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule including taking down the existing fitting complete all as specified and as directed. Make : M/s Hindware / Orient / Seiko / Dripless

S & F in repairs Fancy type chromium plated 15 mm bore Angle / plain Stop valves, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions including taking down the existing fitting complete all as specified and as directed. M/s Hindware / Orient / Seiko / Dripless

S&F for 15mm bore, 45 cm long PTMT PVC connecting pipe fitted with brass unions to connect iron pipe to PVC pipe on both ends and fixed in repairs complete all as specified and as directed. Make : Water tec / Prayag

S &F 110 mm bore PVC (SWR) soil, waste and vent pipes single socked in any length with rubber ring joints fixed to walls / laid in floors complete all as specified and as directed. Make : Supreme / Prince / Finolex

S & F 75 mm bore PVC ( SWR ) , [ ISI MARKED ] bends of any radius complete all as specified and as directed. Make : Supreme / Prince

S & F 110 mm bore PVC ( SWR ) , [ ISI MARKED ] bends of any radius upto 10th storey complete all as specified and as directed. Make : Supreme / Prince

Demolition of Reinforced Cement Concrete of any description and in any position not otherwise specifically provided for, and disposal off debris and rubbish to out side MD land complete all as specified and as directed.

M&L for Excavation over areas not exceeding 1.5 M deep and getting out in Soft / Loose Soil complete all as specified and as directed.

M&L for Excavation over areas exceeding 1.5 M not exceeding 3.0 M deep and getting out in Soft / Loose Soil complete all as specified and as directed.

M & L for Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, etc., and getting out in hard/ dense soil complete all as specified and as directed.

M&L for Reinforced Cement Concrete M 30 design mix in foundations including rafts, footings and mass concrete complete all as specified and as directed.

M&L for Reinforced Cement Concrete M 30 design mix in columns and the like complete all as specified and as directed.

M&L for Reinforced Cement Concrete M 30 design mix for beams and the like complete all as specified and as directed.

M&L for Reinforced Cement Concrete M 30 design mix for slabs supported on walls, beams and columns, in floors, roofs, landings and in shelves and the like complete all as specified and as directed.

M&L for Reinforced Cement Concrete M 30 design mix for fins and facias and the like complete all as specified and as directed.

Use and waste of rough finished flat Form work to sides of concrete foundations, rafts, plinth beams and similar work, vertical or batter complete all as specified and as directed.

Use and waste of Fair finished flat Form work to faces of columns and similar work, complete all as specified and as directed.

Use and waste of fair finished flat Form work to sides of concrete roof beams, lintels and similar work, vertical or batter complete all as specified and as directed.

Use and waste of Fair finished flat Form work to soffits of suspended slabs such as roof slabs, floor slabs and similar work not exceeding 200 mm thick complete all as specified and as directed.

Use and waste of Fair finished flat Form work to soffits of suspended slabs such as roof slabs, floor slabs and similar work not exceeding 200 mm thick complete all as specified and as directed.

M & L for complete removal of existing treatment on walls, preparation of wall surfaces and applying two coats of weather proof Acrylic Exterior emulsion paint of approved make and shade over a coat of approved primer as recommended by the manufacturer over two coats of putty including sand papering on external walls / ceiling surfaces to obtain smooth finish including necessary scaffolding and safty precations complete all as specified and as directed. Make : (i) Weather coat paint :Apex from Asian Paints / All Guard from Berger, Weather Shield Max Exterior Acrylic from ICI Dulux (ii) Make for Putty : JK white cement / Birla wall care / Jenson & Nicholson

S&F of bold metallic stainless steel letters or alphabetes made with 2mm thick sheet, 25mm wide and 10mm thick ( hollow ) fixed in granite cladding elevated from surface, of letters of size 30 x 15cm complete all as specified and as directed.

M & L for prepolished Granite (of any type) work 18mm to 20 mm thick machine cut (table rubbed and polished) in floorings, steps, and the like including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite laid over and including screed bed or bedding layer in cement mortar 1:4, 15 mm thick for laying floor finishes and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of stone complete all as specified and as directed.

M&L for point wiring with two runs of single core 1.5 Sq.mm. (Nominal area) PVC insulated unsheathed multistranded copper conductor cable FRLS (ISI marked) drawn through and including non metallic PVC conduit 20 mm bore medium grade (ISI marked) concealed / surface fitted type including Flush type metal GI boxes for fixing modular type / MS sunken box for conventional type switches, sockets, regulators etc. including provision of multistranded 1.5 Sq.mm copper conductor cable FRLS [ISI marked] as earth wire connected to common earth dolly and earth in distribution board complete all as specified and as directed, for one light/exhaust fan/fan point/call bell controlled by one way switch. Make of Cable : Finolex, Polycab, Plaza, Gloster, Harsh all are ISI marked and FRLS cables Make of Conduit : Avon Plast,Precision, Finolex all are ISI marked.

All as per item No. 136 above but for one 5Amps socket on independent board including 1. 5 Sqmm earth continuty FRLS Copper Cable comlete all as specified and as directed.

All as per item No. 136 above but with two runds of 2.5 Sqmm FRLS copper cable for one 15 Amps, socket point including 2.5 Sq mm FRLS copper conductor cable for earth continuity conductor and connecting it to earth dolly complete all as specified and as directed.

All as per item No. 136 above but with two runds of 4.0 Sqmm FRLS copper cable for one 15 Amps, geyser/AC/ Water cooler point including 4.0 Sq mm FRLS copper conductor cable for earth continuity conductor and connecting it to earth dolly complete all as specified and as directed.

S&F Exhaust fan 230 / 240 Volts AC single phase oscillating 300 mm sweep heavy duty with loures with specification of 1400 rpm, input watt-82W, current 0.35A, free airflow - 1950 cum/hour and noice level 45-50db complete all as specified and as directed. Make : Crompton Greaves / Bajaj / Usha

S & F LED Mirror Light "Linnet" 10 Watts copmlete all as aspecified and as directed. Make : Crompton Greaves Cat Part No LCL-10-CDL / Bajaj / Philips

S&F ceiling rose surface bakelite 65 X 50mm two to three terminals complete all as specified and as directed. Make : Cona / Anchor / Legrand

S & F switch piano flush type single pole 5 Amps oneway AC 230V, 50HZ supply complete all as specified and as directed. Make : Anchor / Cona / Bajaj

S&F Switch socket combination 2 in1, 3 pin, 5 Amp flush type,universsal complete all as specified and as directed. Make : Anchor / Bajaj / Cona

S & F Switch socket combination 3 pin, 15 A flush type complete all as specified and as directed. Make : Anchor / Bajaj / Cona

S&F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as reqd complete all as specified and as directed. Make : Anchor/USHA/CONA

S & F MCB SPN 20 / 32 Amps 240 Volts C curve, complete all as specified and as directed. Make: Indo Asian Cat part No. 811152 / STANDARD / HAVELLS/Schneider

S & F MCB SP 6 to 32 Amps, 240 Volts, C curve, complete all as specified and as directed. Make: Indo Asian Cat part No. 811122 to 811129 / L&T / C&S / Schneider / Legrand

M & L for Sub main wiring with 2 runs of 6 Sqmm PVC insulated FRLS Copper conductor cable including PVC conduit of suitable dia along with one run of 6.0 Sq.mm FRLS copper cable for earth continuity conductor as earth lead and connecting to common earth dolly complete all as specified and as directed. Note: Two runs 6 Sq.mm. cable, one run of 6 Sq.mm cable and one run of PVC conduit will be measured as one unit. MAKE :(i) Make of Cable : Finolex/Polycab/Plaza/Gloster/Harsh all are ISI marked and FRLS cables (ii) PVC CONDUIT : AVON PLAST, PRECISON, FINOLEX [ALL ARE ISI MARKED]

M & L for Sub main wiring with 4 runs of 10 Sqmm PVC insulated FRLS Copper conductor cable including PVC conduit of suitable dia along with one run of 10.0 Sq.mm FRLS copper cable for earth continuity conductor as earth lead and connecting to common earth dolly including taking down old submain wiring complete all as specified and as directed. Note: Four runs 10 Sq.mm. cable, one run of 10 Sq.mm cable and one run of PVC conduit will be measured as one unit. MAKE :(i) CABLE : Finolex, Polycab, Plaza, Gloster, Harsh all are ISI marked and FRLS cables (ii) PVC CONDUIT : AVON PLAST, PRECISON, FINOLEX [ALL ARE ISI MARKED]

M & L for Sub main wiring with 2 runs of 4 Sqmm PVC insulated FRLS Copper conductor cable including PVC conduit of suitable dia along with one run of 10.0 Sq.mm FRLS copper cable for earth continuity conductor as earth lead and connecting to common earth dolly including taking down old submain wiring complete all as specified and as directed. Note: Two runs 4 Sq.mm. cable, one run of 4 Sq.mm cable and one run of PVC conduit will be measured as one unit. MAKE :(i) CABLE : Finolex, Polycab, Plaza, Gloster, Harsh all are ISI marked and FRLS cables (ii) PVC CONDUIT : AVON PLAST, PRECISON, FINOLEX [ALL ARE ISI MARKED]

M & L for Sub main wiring with 2 runs of 2.5 Sqmm PVC insulated FRLS Copper conductor cable including PVC conduit of 20mm dia along with one run of 2.5 Sq.mm FRLS copper cable for earth continuity conductor as earth lead and connecting to common earth dolly complete all as specified and as directed. Note: Two runs 2.5 Sq.mm. cable, one run of 2.5 Sq.mm cable and one run of PVC conduit shall be measured as one unit. MAKE :(i) CABLE : Finolex, Polycab, Plaza, Gloster, Harsh all are ISI marked and FRLS cables (ii) PVC CONDUIT : AVON PLAST, PRECISON, FINOLEX [ALL ARE ISI MARKED]

M&L for Earthing complete with galvanized steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below normal ground level) with top edge of the plate not less than 1.5 m below normal ground level connected to galvanized earth wire of 4 mm dia (up to 7.5 m in length from earth plate ) by means of bolts and nuts checknuts and washers of galvanized iron or steel all as specified and shown in electrical plate no.3 of SSR part I including necessary excavation and earth work in any type of soil PCC 1:3:6 type C1 chamber with RCC 1:2:4 type B1 40 mm thick cover with MS rod 8mm dia 150mm c/c reinforcement both ways, watering funnel, 20 mm dia light grade for protection of earth electrode 20 mm dia for watering complete all as specified and directed and tested on completion.

Taking down carefully copper / aluminium point wiring [light, fan, socket or power] complete including fittings such as switches, ceiling roses, pendants, regulators, sockets etc and making good the disturbed surfaces all as per existing complete all as specified and as directed.

Taking down carefully copper / aluminium sub main wiring 2.5 / 4 / 6 Sqmm etc., and making good the disturbed surfaces all as per existing complete all as specified and as directed.

Taking down ceiling fan/ exhaust fan / Air Circulator/ wall mounting fans of any size, cleaning the cable ends cleaning the dust grease and filling the cavities and, and painting with one coat of synthetic enamel paint and Refixing in original position or new location as directed including replacement of flexible cable complete all as specified and as directed

S&F Vertical DB for provision for four pole MCCB (V-Tech) N3 frame upto 200 A in 35 KA as incomer 4 way 12 out going True IP 43 protection with Test points and distribution boards completely Isolator Neutral bar door earthing, insulated busbar assembly mechanical impact strength IK 08 from the box complete all as specified and as directed Make : Indo-Asian Cat No. 811888 or equilent in Legrand / Havells / Schneider.

S&F MCCB 25 KA 04 pole 125 Amps with adjustable thermal and adjustable magnetic setting complete all as specified and as directed Make : Indo-Asian Cat No. 830053 or equilent in Legrand / Havells / Schneider.

S&F MCB DB single pole and neutral 8 way True IP 43 protection with test reports and distribution boards completely Isolated Neutral bar door earthing, Insulated busbar assembly mechanical impact strength IK o8 from the box double door type complete all as specified and as directed Make : Indo-Asian Cat No. 811807 or equilent in Legrand / Havells / Schneider.

S&F LED wall / surface mounted " batten and tube rod " integrated channel CRCA body, powder coated white regal batten type luminaire pre-wired for 'T8' LED tube light 1 x 18w LED T8 6000K with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and as directed. Make of Batton & tube rod : Bajaj luminaire cat pt No. BLRB DB 118 for 1 x 18W LED of product code 112181 & Bajaj cat No. BLRB 18W CW of product code No. 112066 / Philips / CG / Havells

S&F recessed mount LED down lighter 2' x 2', 36W ultra modern designed architectural LED Luminaire which provide soft-light and glaire free symmetrical illumination suitable for Armstrong /grid ceiling complete all as specified and as directed. Make : Havells cat No. VENUSNEOHE4X1PLR28-36W LED 830MOD OR ITS EQUIVALENT IN Bajaj / Philips / CG / SURYA/ WIPRO/HPL

S&F recessed mount 18 W down lighter with pressure die-cast aluminium heat shink & PC diffuser in white powder coated finish with integrated driver all as specified and as directed. Make : Havells cat No. INTEGRANEODLR18WLED 840S OR ITS EQUIVALENT IN Bajaj / Philips / CG / SURYA/ WIPRO/HPL

Supply and fix fan table / wall mounted 230 W single phase oscillating 400mm sweep complete and making good as existing suraface complete all as specified and as directed Make: Bajaj / Orient / CG

S&F Distribution Board, SPN 4 Way ,Double door 240V with 200Amps rated bus bar complete all as specified and as directed. Make : Indo Asian / Standard / Havells

S&F Ceiling fan complete with electronic type regulator and accessories 230 V, 1200mm sweep, BEE 5 star rated Make CG / Bajaj/Havells

Earthing complete with copper earth plate electrode 600 X 600 X 3.15 mm thick burried directly in ground [earth pit not less than 2.25 m deep below ground level] with top edge of plate not less than 1.50 m below normal ground level connected to 20 mm X 3 mm copper Strip [Earth Lead] and GI Pipe 40 mm, Medium Grade for earthing lead protection to the extent of maximum 7.5m connected to the plate by means of GI Bolts & Nuts complete all as per Electrical plate No. 3 of SSR Part - I, connected to panel / DB including testing on completion including main earthing, Charcoal, Common Salt, PCC [1:2:4, Type B1] Chamber with MS frame made of 40 X 40 X 6 mm Angle Iron with RCC[1:2:4, Type B1] Cover of 40mm thick,renforced with 6mm dia round bars @75mm C/C both ways with MS handle 12mm dia, MS Funnel with 20 mm bore, medium grade GI Watering pipe, wire mesh, earth work excavation etc complete all as specified and as directed.

S & F Earth Continuity Conductor or main earthing lead of Galvanised Iron Strip of size 20 X 3 mm, with all saddles and screws etc.fixed to walls on batten or recess or chases or burried in ground or drawn in conduit / pipe or fixed to poles or any other indicated situation etc complete all as specified and as directed.

SRI JAYANTH ASSOCIATES

SATYAMEGHA ENGINEERS

K SATYANARAYANA ENTERPRISES