SPECIAL REPAIRS TO BLDG NO P 26 AND P 31 AT DWARKA VIHAR AT MIL STN GANDHINAGAR

Amount

Excavating in trenches not exceeding 1.5m wide and not exceeding 1.5 m in depth for foundation of pole, laying of cables etc in soft/loose soil and getting out complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layer not exc 25 cm with soil obtained from excavation complete all as specified and directed.

M&L for providing dry river sand as in sand cushioning to UG cable including punning gently all as directed. Note: Depth after punning shall be measured and paid.

Removing excavated material (Soil) not exc 50 mtr and depositing where directed at a level not exc. 1.5 m above the starting point complete all as specified and directed.

Supply and laying sub class old 'B' burnt bricks, size of brick 230x115x75mm, laid as cable protection cover complete all as specified and directed.

Removing rubbish to a distance exc 1.5 km but not exc 5.0 km out side MD land complete all as specified and directed

Cutting chases pinning in, making good to facings for concealed water tubing etc. cutting exceeding 10 cm but not exceeding 20 cm girth complete all as specified and directed

Taking down chowkhats or frames with shutters (without taking off shutter from the frames) not exc. 1.5 sqm each complete all as specified and directed

Taking down chowkhats or frames with shutters (without taking off shutter from the frames) exc. 1.5 sqm but not exc. 4 sqm each complete all as specified and directed

Taking down shutters of any description exc 1 sqm and n. exc 2 sqm each

S & F 35 mm thick, 2nd class hard wood factory made, glazed & skeleton shutters, open rebated and prepared to receive glass, gauge etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. sizes of members of shutters as specified in SSR Part I. section 8, clause 8.24 (a) complete all as specified and directed

S & F factory made 35 mm thick flush shutters solid core construction with block board core and plywood face panels commercial type on both sides complete all as specfied and directed

S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having PVC sheet strip of 20 mm width stuck iside with solvent cement for stiles and plain colour PVC sheets for top rail lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in MS frame welded sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement supplying and fixing in the frame at site complete all as specified and directed

S&F solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforcement with MS square tube supplying and fixing in opening as per specifications complete all as specified and directed

S & F aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) abd fixing clips of sheet, cast or extruted sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy with length of bolt 300 mm and fixed complete all as specified and directed

S & F aluminium anodised barrel tower bolts of extruded section with length of bolt 150 mm and fixed complete all as specified and directed

S & F aluminium anodised barrel tower bolts of extruded section with length of bolt 200 mm and fixed complete all as specified and directed

S & F stainless steel butt hinges of size 100 mm complete all as specified and directed

S&F butt hinges medium weight cold rolled mild steel of size 100 mm complete all as specified and directed

S & F single action spring hinges, mild steel with steel wire spring stove enameled black size of spring hinge 150 mm all as specified and directed

S & F extruded aluminium alloy handles, fabricated type, anodised of size 150 mm complete all as specified and directed

S & F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed

S & F, in repair stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed

M & L for rolled mild steel angle iron work as in door frames complete drilled for fixing of hinges etc, also fastening and fixing conforming to Fe-290 (Gde E-165) complete all as specified and directed

S&F mild steel work in weather shed posts, main and cross beams, hip and jack rafters, purlins, including special shaped washer etc. complete using ERW or induction butt welded tubes, conforming to IS 1161-1979, Gde St-240 complete all as specified and directed.

S & F aluminium anodised doors/windows/ventilators with one or more rebates including joining cleat for fixing etc complete with frames, shutters and grills of size directed by Engineering-in-charge including handles, tower bolts, grills etc complete all as specified and directed. Note :- Floor door spring sheet glass wire cloth lock etc shall be measured and paid seperately

S&F, in repair, pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet, 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M & L for cutting uneven surface of concrete and reinforcement from drop of fins facias, chajjas using necessary scaffolding and marking good disturbed portion including form work with rendering cement plaster 10 mm thick in cement mortar 1:3 finished even and smooth without using extra cement complete all as specified and directed

M&L for machine cut kota stone slab, 450x600mm ( 18"X24"), 20-25mm thick as in flooring laid over and including cement mortar screed bed of 15mm thick in CM (1:6), laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for machine cut kota stone slab 20-25 mm thick as in riser of steps, skirting, dado and pillar laid over and including rendering 10mm thick in cement mortar (1:4), jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M & L for 15 to 18 mm thick black granite stone slab (table rubbed and polished) in cooking platform, steps, jambs, pillars, windows cills and like in CM (1:4) including pointing in white cement (1:2) using marble dust with admixture and pigment to match with the shade of granite

Rounding to edges of stone slabs one edge such as steps, cooking platform, and other similar situations complete all as specified and directed

M&L for 75 mm thick cement concrete (1:4:8) type D-2 using 40 mm graded stone aggregate as in sub base of flooring/hard standing and finishing the surface even and fair without using extra cement complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size conforming to IS 15658- 2006 of 60mm thickness, M-35 grade including 25mm thick (compacted thickness) sand cushion below paver blocks including takingout old paver block floor complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but noot backing) removing rubish off the premises complete all as specified and directed

M & L for glazed ceramic coloured tiles of size 450 mm x 300 mm x 7 mm on vertical surface such as skirting dados, risers to steps etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, over and including rendering 10 mm thick in cement mortar (1:4) complete all as specified and directed

M & L for coloured non skid ceramic tiles 7 to 8 mm thick, (square/rectangular) , area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including screed bed or bedding layer of 15 mm thick cement mortar (1:6) complete all as sppecified and directed

M & L for coloured non skid ceramic tiles 7 to 8 mm thick, (square/rectangular) , area of each tiles exceeding 0.06 sqm but not exceeding 0.11 sqm in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including screed bed or bedding layer of 15 mm thick cement mortar (1:6) complete all as sppecified and directed

M & L for 50 mm thick cement concrete 1;3:6 type C1 using 20 mm graded stone aggregate as in plinth protection , finishing cement concrete surfaces even and smooth without using extra cement , joints of plinth protection shall be filled with bitumen mastic (1:3) complete all as specified and directed

Taking down cement plaster on brick or stone wall etc including raking out joints hacking for key scrubbing down with water etc complete all as specified and directed

M & L for rendering cement plaster 10 mm thick in cement mortar (1:6) on brick or concrete surfaces complete all as specified and directed

M & L for rendeing cement plaster 15 mm thick in cement mortar (1:4) on brick work or concrete surfaces , complete all as specified and directed.

M & L for rendering 5 mm thick in cement mortar 1:4 on fair faces of concrete in ceiling, chajjas, fins facia etc.complete all as specified and directed

M & L for preparing new plastered or un-plastered ceiling surfaces and applying three coats of white wash complete all as specified and directed

M & L for preparing old plastered or un-plastered ceiling surfaces and applying two coats of white wash complete all as specified and directed

M & L for preparing new plastered or un-plastered surfaces and applying two coats of oil bound distemper over a coat of chalk whitining on walls complete all as specified and directed.

M&L for preparation old plastered or un-plastered surfaces and applying one coat of oil bound distemper on walls complete all as specified and directed

M & L for preparing new plastered or un-plastered surfaces and applying two coats of cement base paint over a coat of chalk whitining on walls complete all as specified and directed.

M&L for preparation old plastered or un-plastered surfaces and applying one coat of cement base paint on walls complete all as specified and directed

S & F 5 mm thick black tinted glass panes fixed to aluminium doors/windows/vents with necessary rubber gaskets complete all as specified and directed

M & L for preparation of new steel surface of any description exc. 10 cm width or girth and applying two coats of synthetic enamel paint over existing shop coat of primer complete all as specified and directed

M&L for preparation old painted steel surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed (make- Asian, Nerolac, Berger, Dulux, shalimar)

M & L for preparation of new wooden surface of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed

Taking up or down steel tubing and connections for 15mm bore of pipe complete all as specified and directed.

Taking up or down steel tubing and connections for 20mm bore of pipe complete all as specified and directed.

Taking up or down steel tubing and connections for 25mm bore of pipe complete all as specified and directed.

S&F, steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 15mm bore of pipe complete all as specified and directed.

S&F, steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 20mm bore of pipe complete all as specified and directed.

S&F, steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 25mm bore of pipe complete all as specified and directed.

Refixing old serviceable steel tubing and connections in new or old position (walls, ceilings, floors etc.) for 15mm bore of pipe complete all as specified and directed.

Refixing old serviceable steel tubing and connections in new or old position (walls, ceilings, floors etc.) for 20mm bore of pipe complete all as specified and directed.

Refixing old serviceable steel tubing and connections in new or old position (walls, ceilings, floors etc.) for 25mm bore of pipe complete all as specified and directed.

S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid as in trenches / floor

S & F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls including stack clamp complete all as specified and directed

S & F 75 mm bore PVC (SWR) bend, any radius complete all as specified and directed

S & F 110 mm bore PVC (SWR) bend, any radius with access door complete all as specified and directed

S&F 75 mm dia (outlet) PVC (SWR) floor trap with grating including jointing with solvent cement all as specified and directed

Taking down steel doors/window/ventilator of any description complete all as specified and directed

S&F in repair brass chromium plated shower rose with or without swivel joint, 125 mm size complete all as specifieid and directed (Make - Marc, Cera, Prayag, Parco, Gem)

S&F,kitchen or laboratory sinks made of stainless steel 1mm thick including supply and fix 32mm bore CP waste coupling, plug, washer, 32mm bore and 60cm long PVC waste pipe including cantilever brackets made of mild steel angle iron 30x30x3mm and flat iron 25x3mm both duly painted with two coats of synthetic enamel paint over a coat of red oxide primer, cutting for and pinning in ends of brackets to errecting stand into wall and making good disturbed portion in cement mortar 1:2 or in PCC 1:2:4, type B-1 using 20mm graded stone aggregate and connecting union to pipe, over all size 495mm x 420mm, bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S & F, in repair, vitreous china squatting pan, 'Orissa Pattern, white of size 580 mm x 440 mm with integral foot rest (excluding flushing cistern and flush pipe) but includiing cleaning the sunken portion of WC by demolition and removeal of old concrete and provn of roof treatment of sunken floor, new lean cement concrete 1:5:10 type E-2 using 40 mm graded, finished even and smooth complete all as specified and directed

S&F, in repair bip tapss fancy type, cast copper alloy with crutch alloy with crutch or butterfly handle, screwed down screwed for iron pipe or for brass ferrule and fixed for 15 mm bore dia of piep all as specified and directed

S&F, Towel Rail, 600mm long of PTMT fixed and including chromium plated brass screws and wooden/plastic cleat (minimum weight 190 gms) complete all as specified and directed.

S & F , in repair concealed stop cock regular body 15 mm with flages complete all as specified and directed

S & F , in repair Grating square 150 mm size of PTMT (Minimum weight 100 gms) complete all as specified and directed

Supply only 32/40 mm waste fittings, brass chromium plated for glazed ware sink, basins etc with long screws, shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed

Supply only PVC waste pipe 32 /40mm bore of size 450 mm to 600 mm long complete all as specified and directed

S&F, in repair 25 mm dia 1 mm wall thickness stainless steel fancy type decorative curtain rod with decorative ball type side brackets fix with wooden guttties complete all as specified and directed

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exc. 15cm thickness (below or above ground level) all as specified and directed.

Dismantling of cast iron , PVC or reinforced concrete drain pipes jointed in cement mortar for 100 mm and 75 mm bore of pipe from wall / floor etc complete all as specified and directed

Taking down carefully copper/aluminum point wiring (light, fan,socket or power) complete,including fixture and fitting such as as switches, ceiling roses, pendants, regulators, sockets,etc excluing light fittings etc,removing materials to store for keeping in safe custudy or for taking credit ( credit for above items should be made as per conditions separately) and making good disturbed surface of walls, ceiling, floor etc to match with the existing surface.

M&L for wiring with and including multi stranded copper conductor 1.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed, FRLS cable, 1100 volts grade, ISI marked with valid CML number, drawing through in and including medium grade, rigid non metallic, PVC concealed conduit of 20mm bore and including cutting chases for conduits and sunken boxes, its accessories & including with multi stranded copper conductor 1.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed, FRLS cable, green colour, 1100 volts grade, ISI marked with valid CML number as continuity earth wire terminating with provision sunken concealed terminal boxes complete all as specified and directed for the following :-

(a) One light/fan point controlled by one switch

(b) One multi purpose socket 5 Amps, Independent board.

(c) One multi purpose socket 5 Amps, on the same board.

(d) One light point controlled by two way switches.

(e) One bell buzzer point controlled by one push buttons independent

M&L for wiring with and including multi stranded copper conductor 2.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed, FRLS cable, 1100 volts grade, ISI marked with valid CML number, drawing through in and including medium grade, rigid non metallic, PVC concealed conduit of 20mm bore and including cutting chases for conduits and sunken for boxes, its accessories & including with multi stranded copper conductor 2.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed, FRLS cable, green colour, 1100 volts grade, ISI marked with valid CML number as continuity earth wire terminating with provision of sunken concealed terminal boxes complete all as specified and directed for the following :-

S&F switch piano, flush button single pole, one way 5 Amps complete all as specified and directed

S&F switch piano, flush button single pole, 2 way 5 Amps complete all as specified and directed

S&F socket outlet 2 in1, 3 pin, 5 Amps, flush type complete all as specified and directed

S&F socket outlet multipurpose, 3 pin, 5 &15 Amps flush type complete all as specified and directed

S&F switch piano flush button single pole, one way 15 Amps complete all as specified and directed

S&F Bell push , flush type single pole, 5 Amps complete all as specified and directed

S&F Ceiling rose, PVC/poly carbonate,isolated body, three terminals.

M & L for ceiling fan regulators, Electronic step type type, AC, 230 Volts complete.

S&F lamp holder, insulated body with back plate for batten fittings complete.

M & L bell electric, Dingdong type A.C. 230 Volts, single pole complete.

S &F fix in repair Distribution Board SPN 4 way, 240 volts, factory made powder coated, double door with neutral and earth link, suitable for fixing MCB,s complete including connecting.

Taking down existing meter box and Supplying, installation, testing and commissioning, in repair, factory made, CPRI approved LT panel , wall mounted board made out of CRCA sheet of 2 mm thick indoor type totally enclosed weather, dust and vermin proof with front opening hinged door and locking arrangement mounted on suitable MS flat iron panel body duly grouted on wall , 240 volts Ssingle phase, 2 wire AC 50 HZ having suitable aluminium bus bar for phase and the neutral insulated with PVC sleeves, space for fixing single phase KWH electric meter of suitable capacity 04 Nos, copper lugs, spacers, mounting channels, rubber gasket, locking knobs, hylam sheet pieces, PVC shrinkable sleeves, nuts and bolts, washers etc and suitable size single core copper wire connections, suitable compartments and epoxy powder spray paint with primer complete all as specified including the following accessories including taking down old u/s distribution board, taking down and refixing serviceable electric KWH meter in new panel (all as per sample):- INCOMING - (a) MCB SPN 63 Amps-01 No (b) R-Y-B phase, LED indicating lamp - 03 Nos .OUTGOING - (a) MCB, SPN, 40 Amp, 10 KA = 04 Nos (b) Space for mounting single phase energy meter-04 Nos (c) copper cable 6 sqmm wire and open terminals for all feeders Note (1) Mounting arrangement of panel included in quoted rate. (2) Qtr No to be mentioned in respective meter on acrylic plate & cost of acrylic plate to be included in quoted rate.

S & F in repair MCB’s single pole, 6 to 32 Amps 240 volts with ‘C’ curve, fixed in sheet metal board complete including connecting.

S & F in repair MCB’s SPN, 32 Amps 240 volts with ‘C’ curve, fixed in sheet metal board complete including connecting.

S&F, in repairs, slim LED light fitting, batten type, with poly carbonate round shape diffuser grey end cape housed is in ideal replcement solution with eligently designed in caps, 20 watt complete set flexible three core copper conductor cable of suitable size and testing on completion all as specified and directed.

S&F, in repairs, slim LED light fitting, batten type, with poly carbonate round shape diffuser grey end cape housed is in ideal replcement solution with eligently designed in caps, 10 watt complete set flexible three core copper conductor cable of suitable size and testing on completion all as specified and directed.

Supply & Fix in repair LED type Bldg security light fittings, IP-66, 25W, Pressure die cast aluminium housing with toughned glass & individual LEDs with secondary optics including taking out old unsv fitting of any type complete all specified and directed.

M & L in replacement sub-main wiring with 2 single core 4 Sqmm PVC insulated, unsheathed, 1100Volts grade, copper multi stranded conductor drawn in and including PVC concealed conduit and conduit assessories including drawing a run of PVC insulated, unsheathed, 650/1100Volts grade, copper conductor multi stranded 4 Sqmm size as continuous earth wire drawn through and connected to main switch/ DB and testing on completion. Note: (i). 2 run of main conductor and one run of earth conductor shall be measured as one length. (ii) Rates quoted shall be inclusive of cutting wall for concealing conduit and making good the same in cement mortar 1:3.

Supply and fix in repair LED industrial bulk head luminiare having IP-65 design aluminium die housing and vendal - resistant cover finished in epoxy powder coated housing of capacity 10 watt complete all as specified and directed.

M&L, in repairs, earthing complete with galvanized steel earth plate electrode of 60 cm x 60 cm x 6mm thick buried directly in ground [earth pit not less than 2.25 metre deep below normal ground level] with top edge of the plate not less than 1.5 m below normal ground level, connected to galvanized earth wire of 4mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No. 3 of MES SSR Part I all as specified and testing on completion.

Taking down existing ceiling fan and depositing in MES store yard for keeping in safe custudy complete all as per specified and directed.

Hanging only ceiling fan and connecting up including provision of cable from ceiling rose after complition of work complete all as per specified and directed.

Taking down existing Electric meter and depositing in MES store yard for keeping in safe custudy and refixing the same after complition of work complete all as per specified and directed.

Taking out old unserviceable LT cable and Supplying & laying, XLPE insulated, PVC inner sheathed, armoured with galvanised steel strip or wire heavy duty underground cable with aluminium multi stranded conductor, 1100 volt grade,of size 10 Sqmm 2 core, laid in trenches/duct, passing through pipe/duct or fixed on pole and connecting and testing complete all as specified and directed.

Taking out old GI Pipe and Supply and laying GI pipe 40mm dia light grade below road / fixed to along the poles / walls with necessary clamping, including encasing the cable into the pipe all as specified and directed.

Shree Builders

Ramdev and Sons

Choudhary Traders and Engineers

ARTI CONSTRUCTION

ALBA AC AND REF SERVICES

Priya Construction co.

DMA PROJECTS

M/s ESS KAY Construction