REPAIR TO INTERNAL ROADS IN DOMESTIC AREA AT AF STN HALWARA UNDER GE (AF) HALWARA

Material & Labour for repair to pot holes any depth not exceeding 1.0 Sqm each including sweeping free from dust and mud, or water scoring sunken surfaces in road path etc cutting around edges, at least 25mm in depth and making good by applying tack coat using paving bitumen @ 5Kg per 10 Sqm, putting in premixed bituminous macadam well rammed and sealed with binder using paving bitumen at the rate of 9.8 Kg Per 10Sqm binded with 0.09 cum stone chipping 6.3mm size and again well rammed (including supply of premixed macadam binder and chippings) depth of pot hole exceeding 30mm complete all as specified and as directed by Engr-in-charge. Note :- (i) Pot holes shall be marked by Engineer-in-charge before commencement of work and same shall be entered in MB after making good and before laying of bituminous premix carpet.

Material and labour for Preparing on black top surfaces by brushing with wire brushes for removing caked mud etc. sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt etc complete all as specified and directed by Engr-in-Charge.

Material and labour for Applying Paving bitumen evenly a priming/tack coat with bituminous primer of grade VG-10 at 5 kg per 10 sq metre completet all as specified and directed by Engr-in-Charge.

Material and labour for Scarifying or picking gravelled,macadam or bituminous macadam surfaces in area exc 400 sqm (n.exc.50mm deep)completet all as specified and directed by Engr-in-Charge.

Material and labour for for Premix bituminous, macadam laid/rolled and compacted to required gradient and camber (consolidated thickness 75mm or less) using Paving bitumen (VG-30), binder content @ 4.0% by weight of total mix & use power roller wt.exc 8 tonne & but not exc 12 tonne for rolling and consolidating formation surfaces in cutting (Including Preparation of surface and priming/tack coat of VG-10 at 10 kg per 10 sqm ). Notes : (i) Hot mix plant of adequate capacity shall be used for heating and mixing of aggregates and binder and shall be laid in single layer with Mechanical Sensor Paver all as specified and directed by Engr-in-Charge. . (ii) The design mix shall be carried out from zonal lab/Govt approved lav/Govt Engg College as approved by GE before incorporation in work

Material and labour for for preparing bituminous surfaces of road and marking 2.5mm thick centre lines,stop lines,dashes,arrows etc.and the like n.exc 10cm wide on roads pavements with hot applied thermo plastic road marking paint of approved colour confirming to BS 3262-1989 with special applicator machine all as per manufacturers instruction complete all as specied and directed by Engr-in-Charge.

Supply and fixing in repair solar cat eye aluminium alloy of anu colour shall (100% water proofing design according to 65) of size 125mm x 125mm x25 mm (shank 65mm) of high efficiency mono rystafie solar pannel 2.4 volt /0.3 watt one NI-ed rechargeable battery (1.2 V) /1600MH) cosisting of super bright LED with 10000 to 18000mcd fixing with epoxy complete as per manufactures instructions etc all as per modal No DA110 (Dhruv) dark eye equivalent of greenllite/ 3M complete all as specified and directed by Engr-in-Charge.

Supply and fixing in repair cat eye solar reflective type of metal body alloy of size 100mm x 100mm x 20mm with PAMA striplens reflector of model No. DA 972.0 fixed with and incl MS stud of suitable size as per manufactures instructions complete all as specified and directed by Engr-in-Charge.

Supply and fixing in repair of Convex Mirror circular of size 1000mm dia made with ABS body,lens/mirror with unbreakable poly carbonate fixed with clamp with MS pipe 50 mm dia and upto 5 feet height and fixed to ground by PCC 1:2:4 block of size 45x45x60 cm including excavation,removal and curing complete all as specied and directed by Engr-in-Charge.

Supply and fixing in repair metal tubular dealineator made out of ABS round body fitted with 2 Nos 65 mm dia highly reflective reflectors made out of PMMA and mounted on 45/50 mm dia mild steel pipe of 600 mm height duly powder coated and thermo plastic elastomer 3 bands of green, red and yellow reflector radium tape of 25 mm wide strips with anti theft steel net for reflector protection including embedding in PCC 1:2:4 (150x150x300mm) type B1 complete all as specified and directed by Engr-in-Charge.

Supplying and fixing retro reflective Overhead informatory road signage and boards, made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type - III of ASTM- D-4956-01 as approved by Engineer-in-charge, letters, borders etc. as per IRC : 67-2001 in silver white with blue colour back ground and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class II of ASTM-D-4956-01 and fixing the same to the plate of structural frame work by means of suitable sized aluminium alloys, rivets or bolts & nuts @ 300 mm centre to centre all along the periphery as well as in two vertical rows along with theft resistant measures, including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminium sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all complete as per drawings, specification and direction of the engineer-in-charge.(Structural frame work including M.S. plate to be provided separately. Rectangular area of the sheet only shall be measured for payment). .

Demolition of cement concrete in ground floor and paving not exc 15 cm thickness (below or above ground level) all as specified and directed by Engr-in-Charge.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed by Engr-in-Charge.

Dismantling floor, path, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, including removing the debris out side the MOD land, complete all as specified and directed by Engr-in-Charge. .

Material and labour for providing PCC (1:4:8) type D2 (using 40 mm graded aggregate), 75 mm thick as in sub base below pavings, floors, paths etc all as specified and directed by Engr-in-Charge. .

Material and labour for Cloured Chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigment including 20mm thick screed bed or bedding layer in cement mortar 1:4, complete all as specified.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed by Engr-in-Charge.

Demolition of brick work built in cement concrete including all quoins, arches, pillers complete all as specified and directed by Engr-in-Charge.

Material and labour for brick work with sub class B bricks, straight or curved on plan exc 6 cm mean radius built in cement mortar 1:6 all as specified and directed by Engr-in-Charge.

Material and labour for for 15 mm thick rendering but 1st coat of 10 mm thick in CM(1:6) and above 5mm thick in CM (1:4) as a 2nd coat of rendering with WPC complete all as specified and directed by Engr-in-Charge. (Note : WPC will be paid separately)

Material and labour for Prepration of new plastered surfaces of wall and applying two coat of cement base paint over a coats of priming plastered and other surfaces all as specified and directed by Engr-in-Charge.

Material and labour for Preparation of new brick,stone,concrete,asbestos cement or plaster surfaces of any description over 10 cm width or grith and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engr-in-Charge.

Material and labour for providing cement concrete (1:2:4) type B-1 using 12.5mm graded crushed stone aggregate as in bands, copings, bed plates, kerbs, including form work complete all as specified and directed by Engr-in-Charge.

Supply and fixing in repair rubber speed breaker of any size/shape of yellow and black colour including all necessary fixing items & as specified and directed by Engr-in-Charge.