REPAIR/REPLACEMENT AND MAINTENANCE OF WATER DISTRIBUTION LINE, VALVE CHAMBER, LT PANELS/STARTER AND ATTENDING EMERGENCY BREAKDOWN TO DISTRIBUTION LINE AT DOLPHIN HILLS UNDER AGE E/M-II OF GE (UTILITY-II) VISAKHAPATNAM

Amount

M & L for Jungle cleaning by cutting and clearing away all grass vegetation, wild growth, sapling, shrubs, brushwoods, under growth roots, cutting of bushes, tree trunk of girth not execeeding 30 cm, cutting of trunk, portion protuding over ground, filling holes and leveling of ground and removing unserviceable materials to a distance n.exe 50m, compelte all as speicified.

Supply and replacement of MS ERW pipe heavy grade pipe 300 mm bore, thickness not less than 5.6 MM laid on suitable size PCC Pillar supports, clamps, bolts and nuts including necessary Tees, elbows, flanges, including cutting etc and preparation of pipe surface and applying two coats of synthetic enamel paint over a coat of zinc chrome primer in open places and with bitumen coating/felt cover for inserting the pipe in position and including making leak proof joints complete all as specified and directed.

All as per SL item No.2 above but 200 mm bore.

All as per SL item No.2 above but 150 mm bore.

All as per SL item No.2 above but 100 mm bore.

All as per SL item No.2 above but 80 mm bore.

All as per SL item No.2 above but 40 mm bore thickness not less than 4.80 mm .

M&L for seven stage cleaning and sterilization of inside UG sump reservoir through bacteriological treatment by using TERBAC GS, TERBAC-G-65 AND ULTRA VOILET RAY Complete all as specified and as directed for following capacity of tanks. Make : Rays cleantech or equivalent/INUS WATERTECH/SATYA ENTERPRISES or equivalent Steps for seven stages are as under First Stage is to drain out the water by using exit valve or high capacity dewatering system. Second stage is cleaning all the algae formation insixe the tank by using TERBAC G10 a laboratory tested branded chemical of the company ans scrubbing the walls of the tanks. Third strage is fresh water cleaning by high speed jet pump. Fourth stage and first bacteria screening is decertification by using TERBAC-G5 a Govt Laboratory certified brannded halogen compound. Fifth stage is cleaning the floor of water tank by industrial vaccum cleaner.

Sixth stage is the second bacteriod screening and sterilizing method by using ultra voilet ray within the tnk and kills all suspended bacteria. Seventh stage of cleaning and third bacteria screening is to sterilize the floor of the water tank by using laboratory certified, branded strong oxidizing agent TERBAC-G65 NOTE: COMPANY WILL SUBMIT GOVERNMENT LABORATORY TEST CERTIFICATE OF TERBAG-G5, TERBAC-G65, FIX THE STICKER MENTIONING THE DATE OF CLEANING & NAME OF SITE AND ALSO PROVIDE, CERTIFICATE CONFIRMING THE COMPLETION OF STERILIZATION OF WATER TANKS MENTIONING THE NAME OF STATION AND DATE OF CLEANING. ALL THE CLEANING & STERILIZATION STAFFS SHOULD BE UNDER ACCIDENTAL INSURANCE COVERAGE).

Semi UG Sump of 3.0 Lakhs Gallons Capacity

Semi UG Sump of 2.5 Lakhs gallons capacity

Semi UG Sump of 1 Lakhs gallons capacity

Semi UG Sump of 0.30 Lakhs gallons capacity

Semi UG Sump of 0.10 Lakhs gallons capacity

Semi UG Sump of 0.05 Lakhs gallons capacity

Semi UG Sump of 0.25 Lakhs gallons capacity

Overhead water tank of capacity 2 Lakhs litres capacity.

HDPE water tank of 10000 litre capacity.

M & L for Cutting/drilling of CI/DI pipe of Size 100/150/200/300 mm bore and inserting 100/150/200/300 mm bore presure relese valve complete with all necessary items such as flanges,DI Specials, welding etc as required on site all as specified and directed.

Supply and replacement of Pressure Reducing Valve flanged end type having material of construction Ductile Iron, spring, pilot valve, internal trims and wetted parts of SS-304, diaphragm of nylon with nitrile reinforcement. complete all as specified and directed for following types

200 MM bore

150 MM bore

100 MM bore

M&L for taking up or down old rusted GI tubings and connections from trenches or from walls/ceilings for the following sizes:- Excavation and earth work will be measured and paid for separately.

20 mm bore

25 mm bore

40 mm bore

50 mm bore

80 mm bore

100 mm bore

Supply and lay in floors/ on roof /on wall / trenches GI water tubing galvanised medium grade with all fittings of following sizes.

20 mm bore

25 mm bore

40 mm bore

50 mm bore

M & L for Refixing old GI tubing and connection in old or new position after cleaning and repairing for the following bores :

20 mm bore

25 mm bore

40/50 mm dia bore

80/100 mm dia bore

Supply and fix 20 mm dia Gun metal gate valve, with iron wheel head, screwed both ends for iron pipe and fixed including cutting the pipe line and taking down old unserviceable valves complete all as specified and directed.

All as per SL item No.14 above but 25 mm dia.

All as per SL item No.14 above but 40 mm dia.

All as per SL item No.14 above but 50 mm dia.

Supply and replacement 50 mm dia high density polythene pipe (HDPE) of pressure rating 6 Kg/ Sqcm , including making leak proof joints on walls/ceilings/laid in floors complete all as specified and directed by Engineer-in-Charge

All as per SL item No.18 above but 32 mm dia.

All as per SL item No.18 above but 25 mm dia.

All as per SL item No.18 above but 20 mm dia.

All as per SL item No.18 above but 15 mm dia.

M&L replacement of unserviceable sluice valve spindle and check nut by un screwing nut and bolts, gasket stuffing box and taking upper portion of sluice valve taking out u/s spindle check nut . Cutting turning, polishing and preparing new SS spindle and check nut from the solid single SS piece of same length , dia of u/s spindle and check nut fixing the new spindle and check nut re assembling sluice valve replacement of u/s gasket nut and bolts and testing for the following bore sizes of sluice valve.

80 mm Dia

Taking out sluice valve stuffing box and re-packing stuffing box of sluice valve including taking apart & assembling & refixing it into its original position & replacement of rubber gasket and nut & bolts for the following sizes :-

80 mm dia

100 mm dia

150 mm dia

200 mm bore

NOTE- Rubber gasket,nuts,bolts and washers will be measured and paid separately

Supply only rubber gasket 3 mm thick

Supply only black bolt with hexagon head and nuts round neck with washer 3 mm thick

Supply and replace 300 mm bore CI sluice valves PN 1.6 (Non - Raising type) conforming to IS 14846 flanged end with iron wheel head and stainless steel spindle flanged joints including necessary nuts, bolts, and washers etc., complete all as specified and directed.

All as per SL. Item No.27 above but for 200 mm dia

All as per SL. Item No.27 above but for 150 mm dia

All as per SL. Item No.27 above but for 100 mm dia

All as per SL. Item No.27 above but for 80 mm dia

M&L for jointing flanged pipe and fittings including provn of rubber or fibre board gaskets and washers required for jointing including taking out fibre gaskets and nuts & bolts for the following sizes:-

80 mm Dia

100 mm dia

150mm bore

200mm bore

250mm bore

M&L for PCC 1:3:6, type C1 (using 20 mm graded granite stone aggregate) for making good the surface where road cutting/ hard standing/ paths and Removing excavated/ demolished material to a distance n.exc. 50m complete all as specified and directed by Engineer-in-Charge.

M&L for stone masonry for walling of random rubble, uncaused, well bonded, built in cement mortar 1:4 for construction of thrust block for the support of water supply pipe line including demolition of stone masonry complete all as specified and directed by Engineer-in-Charge.

Material and labour for taking down defective foot valves from UG Sump, scraping the corroded footvalves and painting with one coat of red oxide along with black enamel paint, replacing rubber gaskets, bottom rubber with spring complete with replacement of necessary bolts, nuts, washers for following sizes complete all as specified and directed.

150/200 mm dia

80/100 mm dia

Supply and replace 200 mm bore CI non return valve with by pass arrangement with necessary rubber gasket, nuts, bolts, and washers etc., complete all as specified and directed.

All as per SL item No.36 above but 100 mm dia.

All as per SL item No.36 above but 80 mm dia.

All as per SL item No.36 above but 50 mm dia.

Supply and fixing in repairs cast iron air release valve with two air outlets, 50 mm dia bore with isolating sluice valve and fixing up in water supply mains including necessary addition / alternation to DI pipe 100/80 mm dia bore with all necesary fittings complete all as specified and as directed.

Supply and fixing in repair cast iron air release valve with two air outlets, 50 mm dia bore with isolating sluice valve and fixing up in water supply mains including necessary addition / alternation to DI pipe 250/200 mm dia bore with all necesary fittings complete all as specified and as directed.

M&L masonary valve chamber of size 900x900x900 mm (internal dimensions) and including necessary excavation and earth work in any type of soil, 100 mm thick PCC 1:4:8 type D2 foundation, brick work in cement mortar 1:6, plastering internal and external surface 15 mm thick in CM 1:4, 50 mm thick PCC 1:3:6 type C1 (using 20 mm graded stone aggregate) coping, 50 x 50 x 6 mm thick MS angle iron, 5 mm thick MS plate cover with locking arrangement, painting exposed steel surfaces with two coats of synthetic enamel paint over a coat of zinc chrome primer including dismantling unserviceable compete all as specified and directed by Engr-in-Charge.

All as per Sl. item No. 42 above but of size 1200x1200x1200 mm (internal dimensions)

Labour only for attending break down of DI pipe pipe line bursting / cracks and including cleaning / removal of broken pipe pieces of various lengths through gas cutting / manual cutting as per site requirement and including inserting necessary specials such as pipes, DI Collar / mechanical Joints etc as per site requirement, testing for leakages of lead joints, testing and necessary dewatering complete all as specified and directed by Engr-in-Charge, for the following sizes:- Note 1 :- The quoted rate is deemed to be include the following:- (i) Arrangement of suitable Pump sets for dewatering at the time of attending break down including JCB's and Cranes as per site requirement . (ii) Necessary labour/trade men for attending break down. (iii) Labour element required for fixing DI pipes, specials, fittings etc. Note 2 :- Earth work, Supply only DI pipes, specials, fittings will be measured and paid seperately under relevant items.

300/250/200 mm bore pipe

150/100 mm bore pipe

Supply only DI K9 water supply pipe lines of size 300 mm bore as per IS 455:1989 bituminous coating as per Annex 'C' of IS 8329 with flanged ends complete

Supply only DI K9 water supply pipe lines of size 250 mm bore as per IS 455:1989 bituminous coating as per Annex 'C' of IS 8329 with flanged ends complete

Supply only DI K9 water supply pipe lines of size 200 mm bore as per IS 455:1989 bituminous coating as per Annex 'C' of IS 8329 with flanged ends complete

Supply only DI K9 water supply pipe lines of size 150 mm bore as per IS 455:1989 bituminous coating as per Annex 'C' of IS 8329 with flanged ends complete

Supply only DI K9 water supply pipe lines of size 100 mm bore as per IS 455:1989 bituminous coating as per Annex 'C' of IS 8329 with flanged ends complete

Supply only DI specials such as bends (any type, radius and angle) tapers any type, straight, bend, increasing, decreasing or double socket etc.) tee pieces single branch, "Y" junction, double branch, cross (all sockets or sockets and spigot) collars, caps and plugs upto 300 mm bore.

Burning out lead joint in position including removing old lead for the following sizes:-

100 mm bore.

150 mm bore.

200 mm bore.

250 mm bore.

Material and labour for run lead joint for spigot and socket pipes (CI/DI) and fittings of size 100 mm complete all as specified and directed by Engr-in-Charge.

All as per Sl. Item No.52 above but of size 150 mm bore.

All as per Sl. Item No.52 above but of size 200 mm bore.

All as per Sl. Item No.52 above but of size 250 mm bore.

Supply and replace submersible pump controller 3 Ph, 415 V for pump capacity upto 5 HP complete all as specified and as directed.

Supply, laying LT UG XLPE insulated PVC FRLS, screened , PVC bedded and PVC tape sheathed galvanised steel strip or wire armoured electric power cable (heavy duty) 1100 volts grade with stranded aluminium conductor of size 4 core 16 Sq mm including taking out old un-serviceable cable complete all as specified and directed. Note:- Excavation and earth work, sand cushiong, cable covers shall be measured and paid separately.

All as per Sl. Item No.57 above but 3 .5 Core 25 Sqmm

All as per Sl. Item No.57 above but 3 .5 Core 35 Sqmm

All as per Sl. Item No.57 above but 3 .5 Core 70 Sqmm

All as per Sl. Item No.57 above but 3 .5 Core 95 Sqmm

All as per Sl. Item No.57 above but 3 .5 Core 120 Sqmm

Excavating in trenches not exc 1.5 m wide and not exc 1.5 m in depth for foundation, laying of cable/pipes etc. n exc 10 sq m on plan and getting out in soft/loose soil complete all as specified and directed.

Returning filling in, including spreading levelling watering and well ramming in layers n.exc 25 cm thick complete all as specified and directed.

Removing excavated surplus soil to a distance n.exc. 50m distance and depositing where directed at a level n.exc. 1.5 m above the starting point all as specified and directed.

Supply and laying Sub Class 'B' bricks of old size (23x11x7cm) laid along aligment of cable as protection to cable in trenches complete all as specified and directed by Engineer-in-charge

Supply and spreading clean dry sand for cable cushioning in trenches complete all as specified and as directed. Note: Punned thickness shall only be measured and paid.

M&L for taking out existing any type pumpset/airblower of following capacity for servicing by disconnecting motor and blower/ pump set, pipe line and removing of all parts like bearing, bushes, impeller, shaft etc cleaning all surfaces and scales/ sludge/ dirt/ formed inside/out side pumpset/blower etc Lubricating/ greasing at proper places and re fixing in position with all serviceable parts with motor incl painting with one coat of anti corrosive paint over red oxide primer and writing MES /SM No and testing and commissioning all as directed by Engr-in-charge.( Note - spares like bearings will be measured and paid separately against supply only)

15 HP to 20 HP

10 HP to 12.5 HP

Supply only ball bearings suitable for centrifugal and mono block pumps motors as existing at site

15 HP to 20 HP

10 HP to 12.5 HP

Supply only blower containers oil (SP320) as required at site

Supply only CI impeller suitable for centrifugal / mono block pumps for the following capacities of 15-25 HP

Supply only CI gland plate high tension studs for Centrifugal / mono block pumps for the following capacity of 15-25 HP

M&L for disconnecting and removing the existing defective Mono block / centrifugal pump set motor of any make of following capacity from the installed position by putting dummy plate to suction and delivery removing the burnt out winding and re-winding the same with super enamelled copper wire of same gauge and same No of turns of existing make insulating winding with existing class of insulation varnishing baking up including replacement of base foundation nuts, bolts and re-installation of pump, testing to satisfactory performance complete all as directed by Engineer-in-charge. Note : Bearings, CI gland plates, Terminal block, shaft shall be measured and paid separately under relavent items of BOQ

15 HP to 20 HP

10 HP to 12.5 HP

M/s.DSRK CONSTRUCTIONS

LAKSHMI SAI CONSTRUCTIONS

GVR CONSTRUCTIONS

MSN ENGINEERING WORKS

Prasad and Suresh Constructions