Maintenance and Upgradation of DIPR Complex at Poloview Srinagar by way of Repairing / Renovation of wooden Paneling, Face lifting of whole complex and Development of Lawn / Road and Construction of 2 No. Attached Washrooms with the Auditorium (Phase

Dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking within 50 meters lead Thickness above 10 mm upto 25 mm

Painting with silicon and acrylic emulsion based water thinnable sealer of approved brand and manufacture on wet or patchy portion of plastered surfaces: Two coats

Providing and fixing of waterproof plywood BWR in walls, ceiling or like of approved brand and manufacture with all necessary fittings and fixtures, scafoldings and frame work, all complete as per the directions of the Engineer-in-Charge including all carriages complete job. 12mm

Providing and fixing of imported wooden panelling lining on walls , ceilings tongued and grooved planks including cost of ground work of 12mm to 10mm (as per requirement) thick ply 50mm wide 600mm*600mm center to center horizontally and vertically fixing with rawl plugs and screws and cover mouldings but including cost of nails, screws and scafolding etc. including 50mm wide wooden cornice etc. complete (12mm thick)

French spirit polishing, Two or more coats on new works including a coat of wood flller.

Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 meters lead.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS:277 and consisting of angle cleats of size 25 mm widex1.6mm thick with flanges of 27mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x40mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.5mm of required length with nuts & bolts of required size and other end of angle hanger fixed with G.I. channels 45x15x0.9 mm running at the spacing of 1200 centre to centre, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm each having clips of 10.5 mm at 450mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64mm diaX230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre to centre, with 25mm long drive-all screws @ 230 mm interval ,including fixing of gypsum board/calcium silicate board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25mm at 230mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the gypsum board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150mm on both sides of joint and two coats of primer suitable for board, all as per manufacturers’ specification and also including the cost of making openings for light fittings, grills diffusers, cutouts made with frame of perimeter channels suitably fixed all complete as per drawing and specification and direction of the Engineer-in-Charge but excluding the cost of painting with: 8 mm thick Calcium Silicate Board made with Calcareous and Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process.

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in : Cement mortar 1:4 ( 1 cement : 4 coarse sand)

Carriage for 20km @475 No of Bricks /Cum