REPAIR/REPLACEMENT OF WOODEN/STEEL FURNITURE INCLUDING PAINTING TO STEEL FURNITURE AND POLISHING/VARNISHING OF WOODEN FURNITURE AT ARMY STATION KATIHAR UNDER AGE (I) (AF) PURNEA

Amount

REPAIR TO CHAIR DINING FD-228 Removing /taking out existing unserviceable damaged/broken rear leg and supply and fixing of new rear leg made out of well seasoned 1st class hard wood free form knot, sap wood etc of existing size including providing of PVC shoe at the bottom of the legs with screw. complete all as shown on drg & directed by Engr-in- Charge.

-do- all as per item No 1 above but front leg of existing size

-do- all as per item No 1 above but front/back/side rails of existing size

Removing of old broken stiffner and replacing with new stiffner of existing size all as specified and directed by the Engr-in-Charge

M&l for preparation of old exposed wooden surfaces by scrapping with sand paper and smoothing of surface, filling of bore holes with wooden putty paste rubbing of surface with sand paper till smoothening and polishing to chair dining all as directed by Engr –in- Charge.

REPAIR TO CHAIR WRITING FD-258 Removing /taking out existing unserviceable damaged/broken rear leg and supply and fixing of new leg made out of well seasoned 1st class hard wood free form knot, sap wood etc of existing size including providing of PVC shoe at the bottom of the legs with screw complete all as specified & directed by Engr-in- Charge.

All as per item No. 6 above but front leg of exisitng size.

All as per item No. 6 above but arms of exisitng size.

All as per item No. 6 above but back/front/side rail of exisitng size including drilling holes for re-caning and finished with french polish as specified and directed by the Engr-in-Charge

M&l for preparation of old exposed wooden surfaces by scrapping with sand paper and smoothing of surface, filling of bore holes with wooden putty paste rubbing of surface with sand paper till smoothening and polishing to chair writing all as directed by Engr –in- Charge.

REPAIR TO TABLE DINING 6/8 PERSONS FD-30(M) Taking out old userviceable top from table dining 6/8 pers and supply and fixing new top of existing size made out of 19/20mm thick, commercial face particle board bonded teak veneered finish of approved quality including Providing 19 x 4mm size 1st class hard wood semi oval shape beading all around complete all as specified and directed and shown on drawing

M&L for replacement of broken/damaged side long rail of existing size of table dining 6/8 persons with new side long rail of 1st class hard wood and fixing with bamboo nails and as directed by Engr –in- charge.

M&L for replacement of broken/damaged side short rail of existing size of table dining 6/8 persons with new side short rail of 1st class hard wood and fixing with bamboo nails and as directed by Engr –in- charge.

M&L for replacement of broken/damaged legs of existing size of table dining 6/8 pers with new leg of 1st class hard wood including providing of PVC shoe at the bottom of the legs with screw. All as directed by Engr-in-charge (each leg shall be measured)

M&L for preparation of old exposed wooden surfaces by scrapping with sand paper and smoothing of surface, filling of bore holes with wooden putty paste rubbing of surface with sand paper till smoothening and polishing to table dining all as directed by Engr –in- Charge.

REPAIRS TO TABLE DINING 6'-3''x2'-3''x2'-6'' FD-89(M) Taking out old userviceable top from table dining 6'-3''x2'-3''x2'-6'' and supply and fixing new top of existing size made out of 19/20mm thick, commercial face Plywood and fixed on the top of Aluminium sheet of existing size fixed on the top of iron frame .all around complete all as specified and directed and shown on drawing

M&L for replacement of broken/damaged table dining 6'-3''x2'-3''x2'-6'' square bar frame of existing size with legs and shoe cape with removing of top and refix the same with screw nails and as directed by Engr –in- charge.

M&L for preparation of old exposed iron surface surfaces by scrapping with sand paper and smoothing of surface, filling of bore holes with putty paste rubbing of surface with sand paper till smoothening and polishing to table dining all as directed by Engr –in- Charge.

TABLE BED SIDE FD-245,265,275 Taking out old userviceable top from table bed side and supply and fix new topof existing size made out of 19/20mm thick, commercial face particle board teak veneered finish of approved quality including Providing 19 x 4mm size 1st class hard wood semi oval shape beading all around complete all as specified and directed and shown on drawing

Taking out broken damaged back plywood from back of table bed side of size 610x450mm and S&F new plywood BWR Gde 6mm thick commercial complete all as specified and as directed.

Taking out broken/damaged leg of table bed side and S&F new legs of size 100x45x45mm made out of well seasoned 1st class hard wood, free from knot, sap wood etc duly fixed with PVC shoe at the bottom of legs with screws. complete all as specified & as directed and shown on drg.

M&L for preparation of old exposed wooden surfaces by scrapping with sand paper and smoothing of surface, filling of bore holes with wooden putty paste rubbing of surface with sand paper till smoothening and polishing to table bedside. Complete all as directed by Engr –in- Charge.

TABLE CENTRE FD-235 Taking out old userviceable top from table center and S&F new top of existing size made out of 19/20mm thick, commercial face particle board teak veneered finish of approved quality including Providing 19 x 4mm size 1st class hard wood semi oval shape beading all around complete all as specified and directed and shown on drawing

Taking out old broken/damaged leg of table centre and S&F new leg made out of well seasoned 1st class teak wood, free from kont, sap wood etc of existing size including Providing PVC shoe at the bottom of the legs fixed with screw. complete all as shown on drg and as specified and as directed.

All as per item No 24 above but top rail made out of well seasoned1st class hard wood.

M&L for preparation of old exposed wooden surfaces by scrapping with sand paper and smoothing of surface, filling of bore holes with wooden putty paste rubbing of surface with sand paper till smoothening and polishing to table bedside. Complete all as directed by Engr –in- Charge.

RE-CANING OF CHAIR M&L for re-canning of chair any type with 2mm wide plastic cane half oval shape to a true shape for general caning as per godrej pattern and 4mm wide plastic cane for bordering around of caning of chair all types, all as specified and directed by Engr-in-charge.

POLISHING TO ALL WOODEN ITEMS OF FURNITURE (Only Polishing) M&L for preparation of old exposed wooden surfaces of chair dining other than those already repaired and polished above by scrapping with sand paper and smoothing of surface, filling of bore holes with wooden putty paste rubbing of surface with sand paper till smoothening and polishing to chair dining all as directed by Engr –in- Charge.

-do- all as per item 28 above but chair easy

-do- all as per item 28 above but Table writing

Bed Plywood Top FD-246 Removing the old unserviceable head board from bed plywood top, S&F new head board of size 900x660mm made out of 02 nos of vertical of size 60x60x660mm using second class hard wood (vertical shall be shaped as legs of size 60 x60mm at top and 30 x30mm at the bottom) and 2 Nos of stiffeners 40 x60mm (top and bottom round shape) with 75 mm width and 22 mm thick soft wood battens between stiffeners covered with 4mm thick plywood OST exterior grade on both side and 12mm half rounded taak wood beaing round the edges of plywood by providing 2 Nos of 25mm size round head brass screws for MNF set key holes and applying two coats of french polishing etc, complete all as per drawing and as directed.

All as per item No 31 above but foot board of bed plywood top of size 900x 500mm

S&F long rail of bed plywood top of size 90x35mm, 1980mm long made from 1st class teak wood and providing brackets made from flat iron -02 Nos of size 35x6mm thick 200mm long on both ends and finishing the exposed wooden surface with french polishing including removing the old unserviceable long rails all as directed and as per drawings,

Removing the old unserviceable pealed plywood from bed plywood top, S&F new plywood commercial type, exterior grade, approved quality of size 1900x900mm 12mm thick on both side complete all as per drawing and as directed.

M&L for preparation of old exposed wooden surfaces by scrapping with sand paper and smoothing of surface, filling of bore holes with wooden putty paste rubbing of surface with sand paper till smoothening and polishing to Bed plywood top. Complete all as directed by Engr –in- Charge.

CHARPOY GI PIPE NEWAR/PLYTOP FD-220 M&L removing old unserviceable nylon newar from charpoy GI pipe and reweaving both side with best quality nylon newar 50mm wide which shall be white/light colour not made out of recycled nylon and weight not less than 1.5 Kgs in each charpoy, all as specified and directed by Engineer-in-charge.

Removal of existing newar of Charpoy GI/IP and S & F of two nos of MS Flat iron 40mm X 6mm , 900 mm long and welding on the long rails at 90 degree so as to divide tha long rails into three equal parts.

S & F of 12mm thick plywood BWR of approved quality size 1980mm X 900 mm, cutting into correct dimension and rounding at edges to give it a perfect shape with 14 Nos suitable dia and length of nuts and bolts all as directed.

Labour only for drilling holes 14 nos on GI charpoy three each on long rails, two on short rails and two on the flat iron welded on the two rails with a suitable drilling machine. All as directed by the engr-in-charge

S & F GI Elbow 32mm dia heavy duty ISI marked after taking out old U/S GI elbow all as specified and directed by Engineer-in charge

S&F GI check nut 32 mm size, heavy duty ISI marked after taking out old u/s check nut from charpoy GI pipe, all as specified and directed by Engineer-in-charge.

Taking out broken/damaged long rail from charpoy GI pipe and S&F new long rail of charpoy GI pipe 32mm dia med grade, ISI marked including cutting, threading , all as specified and directed by Engineer-in-charge. Make: TATA/JINDAL/BANSAL

Taking out broken/damaged short rail from charpoy GI pipe and fixing short rail made out from old pipe including cutting for required size and shape & threading and fixing (old pipe shall be obtained from Ser No 16d) all as specified and directed by Engineer-in-charge.

Taking out unserviceable legs from charpoy GI pipe and fixing leg made out of old pipe including cutting of required size and shape & threading and fixing (Old pipe shall be obtained from Ser No 16d and 15e) all as specified and directed by Engineer-in-charge.

REPAIR TO CHAIR VERANDAH FD-236 Removing old unserviceable cane from chair verandah and recaning with new plastic cane 4mm width half round including M&L for painting two coats with white synthetic enamel paint on entire steel/iron surface of chair before recaning and S & F of new hard rubber toes 15mm dia at bottom of legs after taking out old toes. All as specified and directed by Engineer-in-charge.

M&L repair to chair verandah by welding (if required) and painting two coat white synthetic enamel paint. All as specified and directed by Engineer-in-charge.

REPAIR TO ALMIRAH STEEL LARGE/MEDIUM FD-67(M) M&L for one coat spray painting with synthetic enamel paint of approved shade on almirah steel large internally and externally including shelves & internal locker complete after preparation of old painted steel surfaces by scrapping/rubbing down all as directed by Engr –in- Charge.

All as per item No 48 above but for Almirah steel medium with shelves

M&L for repairs of legs of almirah steel large by replacing old/damaged legs with 1mm thick MS sheet and fixing the new legs by welding to almirah steel large and applying one coat painting with synthetic enamel paint 1st garde on new legs externally complete after preparation of old/new steel surfaces by scrapping/rubbing down all as specified by Engr-in-charge.

Taking out old unserviceable lock from almirah large/med steel and S&F new lock best quality Make godrej all as specified and directed by Engineer-in-charge.

Taking out old unserviceable handle from almirah large/med steel and S&F new one make Godrej , all as specified and directed by Engineer-in-charge.

CHAIR CB STEEL WITH/WIHTOUT ARMS Taking out existing unserviceable iron clip flat iron from the chair CB steel with and without arms & supply and fixing 25x3mm thick & 50mm long FI clip by necessary welding to fix the seat and applying two coats of synthetic enamel paint of approved shade over a coat of red oxide primer. Rest all as directed by the Engineer-in-Charge

M&L for repairs to chair CBA steel with/without arms by replacing broken/damaged seat frame with new 1st class hard wood frame including canning, drilling holes and painting with synthetic enamel paint of approved shade complete all as directed by Engr –in- charge.

-do- all as per item 54 above but back

M&L for one coat of painting with synthetic enamel paint of approved shade to all steel portion of chair CB steel with/without arms complete after preparation of old painted wooden surfaces by scrapping/rubbing down including providing PVC/rubber toes at the bottom of legs and cap on top of tube all as directed by Engr –in- Charge.

LOCKER BEDSIDE M&L for one coat spray painting with synthetic enamel paint of approved shade on bedside locker steel internally and externally including shelves complete after preparation of old painted steel surfaces by scrapping/rubbing down all as directed by Engr –in- Charge.

Taking out old unserviceable handle from bedside locker steel and S&F new one of best quality, Make - Godrej , all as specified and directed by Engineer-in-charge. Note:-The contract sum shall be arrieved at after deducting amount of schedule of credit from the total quated amount.

M/S. MAJUMDER CONSTRUCTION

ALAM ENTERPRISES