Construction of Community Hall near MSDP Girls Hostel, Gaurang TN_38_1

Earth Works: 2.6.1 Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means in foundation Trenches or drains not (exceeding 1.5m in width or 10sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50m. All kinds of Soil

2.25 Filling available excavated earth ( excluding rock ) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50m and for all lift.

2.25(a) Excavating, Supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20cm in trenches, plinth, sides of foundation etc. complete for all lift.

16.12 Dry brick pitching half brick thick in drains including supply of bricks and preparing the surface complete : 16.12.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

4.1.6 Providing and laying in position cement concrete of specified grade excluding the cost of cnetering and shuttering - All work up to Plinth level: 1:3:6 ( 1 cement : 3 coarse sand ( zone-III) : 6 graded stone aggregate 40 mm nomial

2.53.3.1 Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling12 mm diameter holes and plugging

4.17 Making plinth protection 50mm thick of cement concrete 1:3:6 ( 1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top

11.3 Cement concrete flooring 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc.complete.

5.22.6 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

5.22A.6 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

5.9.1 Centering and shuttering including strutting propping etc. and removal of form for Foundations, footings, bases of columns etc, for mass concrete.

5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers

5.9.6 Columns pillars piers Abutments posts and struts

5.33.1.1 Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzo;ana / Ordinary Portland / Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the Engineer-in-charge, for the following grades of concrete: Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works upto plinth level. Concrete of M25 grade with minimum cement content of 330 kg / cum

5.33.2.1 All works above plinth level ipto floor V level. Concrete of M25 grade with minimum cement content of 330kg/cum

6.1.2 Brick work with common burnt clay Modular Cement Mortar brick of class designation 7.5 in foundation and Plinth in: cement Mortar 1:6 ( 1 cement : 6 coarse sand)

6.13.2 Half Brick Masonry with common burnt clay F.P.S (Non Modular) bricks of class designation 7.5 in super structure above plinth level upto floor V level. cement Mortar 1:4 ( 1 cement : 4 coarse sand)

13.5.2 15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix: 1:6.( 1 cement : 6 Coarse sand )

13.4.2 12 mm cement plaster : 1:6 ( 1 cement : 6 coarse sand )

13.46.1 Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied@ 2.20 kg/10 sqm)

13.80 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

13.83.2 Wall painting with acrylic emulsion paint, having VOC ( Volatile Organic Composite) content less than 50 grams/ litr, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. Two coats

26.86.5 Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58- 60 (Suspension Grade), calcium carbonate and natural fibers (woodpowder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Frame size 65 x 150 mm

26.86.7 Frame size 65 x 150 mm

26.87.1 Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full bodythreaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) 30 mm thick

26.87.2 35 mm thick

13.61.1 Painting with Synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more Coats on new work

21.10 Providing and fixing double glazed hermetically sealed glazing in aluminum windows, ventilators and partition etc. with 6 mm thick clear float glass both side, having 12 mm air gap, including providing EPDM gasket, preforated aluminium spacers, desiccants, sealant ( Both primary and secondary sealant) etc. as per specifications, drawings and direction of Engineer-in-charge complete

21.8.1 Filling the gap in between aluminium frame & adjacent RCC/Brick/Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete.upto 5 mm depth and 5 mm width

9.97.2 Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than gradeAC 10 as per IS 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete: 250mm x 10mm

9.100.1 Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than gradeAC 10 as per IS: 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete: 125mm

9.101.1 Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than gradeAC 10 as per IS 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete . Single rubber stopper

9.103 Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than gradeAC 10 as per IS 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete .

10.25.1 Steel work welded in built up sections/ framed work, including cutting,hoisting,fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete

10.25.2 In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

11.39 Providing and laying rectified Glazed Ceramic floor tiles of size 300 x 300 mm or more ( thickness to be specified by the manufacturer), of 1st quality conforming to IS: 15622, of approved make, in colours white,Ivory,Grey,Fume Red Brown, laid on 20 mm thick cement mortar 1 : 4 ( 1 cement : 4 Coarse sand ), jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with white cement and matching pigments etc., complete

8.31 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of step sand dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shadecomplete.

16.90 Providing and laying tactile tile ( for vision impaired persons as per standards) of size 300x300x9.8 mm having with water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20 mm thick base of cement mortar 1 : 4 ( 1 cement : 4 coarse sand ) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-charge.

12.45.1 Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sgm (both side linclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x I.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm diax 50mm liong with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of reguired length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.S mm thick botom wedge of 80mn with tapered flanges of 26 mm each having lips of 10. 5 mm, at 450 mm centre to centre, shall be fixed in a ldirection perpendicular 1o G.L. intermediate channel with connecting clips made out of 2.64 mm diax 230 mm long 1G.1. wirce at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry woal serews @ 230 mm interval, including fixing of gypsun board to celing secion and perinmeter Ichannel with the help of dry wall serews of size 3.5 × 25 mm at 230 mm cle, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, lfinishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer (suitable for board, all as per manufacturer's specifiocation and also including the cost of making openings tor light fitings, grills, difiusers, cultouts made with frame of perinmeter channels sutably flxed, all complcte as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick uapered edge eypsum plain boardcontoming 1o IS:2095- (Pan1):2011(Board wih BIS certification marks)

12.45.4 Fully perforated Gypsum Plaster Board of size 1200 x 2400 x 12.5 mm having approx 15% perforated area with perforation size and pattern as approved by the engineer-in-charge as per manufacturer's specification, with all 4 sides tapered and backed by acoustical tissue with NRC value not less than 0.60

10.2 Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including, cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of cormugation as approved by Engineer-in-charge) 0. 50 mm (+ 0.059%) total coated thickness with zinc coating 120 grams per sgm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and palyester top coat 15-18 microns, Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet Ishall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including Icutting to size and shape wherever required.

WATER SUPPLY AND SANITARY : Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10mm gap for thermal expansion. (i) Single socketed pipes. 110mm diameter

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement, and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. consealed work, including cutting chases and making 20 mm dia nominal outer dia pipes

25mm nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride(CPVC)pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, this includes joiting of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 40mm nominal outer dia Pipes.

Providing and fixing brass bib cock of approved quality 20mm nominal bore

Fixing water meter and stop cock in G.I. pipe line including cutting and threading the pipe and making long screws etc. complete (cost of water meter and stop cock to be paid separately).

Providing and fixing wash basin with C.I brackets, 15mm C.P. brass pillar taps, 32mm C.P brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever White Vitreous china wash basin size 630x450mm with a pair of 15mm C.P brass pillar taps

providing and fixing white vitreous china pedestral type water closet (european type) with seat and lid 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I brackets, 40mm flush bend overflow arrangement with specials of standard make and musquito proof coupling of approved municipal design complete, including painting of fittings and brackets cutting and making good the walls and W.C pan with ISI marked white solid plastic seat and lid

Brass full way valve with C.I. wheel (screwd end) 32mm dia

Providing and fixing on wall face unplasticised- PVC moulded fittings/accessories for unplasticised rigid PVC rain pipes conforming to IS : 13592 type A, including jointing with seal ring conforming to IS : 5382, leaving 10mm gap for thermal expansion. Single tee with door 110x110x110mm

Bend 87.5 110mm Bend

Reducer for 48.60mm x 42.70mm outer Dia SS pipe

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600mm long towel rail with total rail with total length of 645mm, width 78mm and effective height of 88m. Weighing not less than 190gms.

Providing and fixing 600x450mm beveled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P. Brass screws and washers complete.

Providing and fixing PTMT grating of approved quality and colour. Rectangular type witrh openable circular lid 150mm nominal size square 100mm diameter of the inner hinged round grating

Providing and fixing C.P. Brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690gms. 15mm nominal bore

Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105gms.

Providing and fixing 600x120x5mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40mm long screws, rawl plugs, etc, complete.

Providing and fixing toilet paper holder : C.P. Brass

Slotted cowl (tenosinal guard) 100mm dia

SEPTIC TANK (100 USERS : Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means in foundation Trenches or drains not (exceeding 1.5m in width or 10sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50m. All kinds of Soil

Dry brick pitching half brick thick in drains including supply of bricks And Preparing the surface complete : With common burnt clay F.P.S.(non modular) bricks of class 7.5

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20mm nominal size derived from natural sources)

steel reinforcement for R.C.C. work including strengthening, cutting, bending, placing in position and binding all complete upto plinth level. Hot rolled deformed bars.

15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement mix : (1 cement: 3 fine sand)

Centering and shuttering including strutting, propping etc, and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete base

Suspended floors, roofs, landings.balconies and access platform Base

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work upto plinth Level : (I cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20mm nominal size derived from natural sources

Brick work with common burnt clay F. P S. (non modular) bricks of class designation 7.5 in foundation and plinth in : Cement mortar 1:4 (1 cement : 4 coarse sand)

Cement plaster 1 : 3 (1cement : 3coarse sand) finished with a floating coat of neat cement. 20mm cement plaster

Square shape 450x450mm precast R.C.C. manhole cover with frame - L.D -2..5

Constructing soak pit 1.20x1.20x1.20 m filled with brickbats including S.W. drain pipe 100mm diameter and 1.20m long complete as per standard design.

(DEEP TUBEWELL BORING) : Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part 1), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level. All types of soil 300 mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (electric Resistence welded) FE 410 mild steel screwd and socketed/plain ended casing pipes of required dia, conforming to IS : 4270, of reputed & approved make, including painted with outside surface with two coats of anticorrosive paint of approved brand and manufacture , including required hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of engineer-in-charge. 100mm nominal size dia

Gravel packing in tubewell construction in accordance with IS : 4097, including providing gravel fine/medium/coarse, in required grading & sizes as per actual requirrement, all complete as per direction of engineer-in-charge.

Providing and fixing to filter and lowering to proper levels 40mm G.I. pipe for tube well including cleaning and priming the tube well.

Providing and placing in position filters of 40mm diameter G.I. pipe with brass strainer of approved quality.

Providing and fixing C.I double acting air valve of approved quality with bolts, nuts, rubber, insertions etc. complete (the tail pieces, tapers, etc if required will be paid separartely) : 50mm dia

Polyethylene water storage tank with cover and suitble locking arrangement

SOUND SYSTEM : Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker complete as required.

Supplying, installation, testing & commissioning of 1.5/3/6W metal box ceiling/wall speakers complete as required.

Supplying, installation, testing & commissioning of ceiling/wall mounted loud speaker, 3/1.5 watt in ABS enclosure complete as required.

Supplying, installation, testing & commissioning of 6 inches dia, 2watts, 70/100 volts ceiling speaker complete as required.

Supplying, installation, testing & commissioning of digital audio amplifier 75watt, 25v rms operating at 240 volt AC supply complete as required.

CABLING AND WIRING : Supplying & laying of 2x1.5sqmm fire survival armoured cable, 600/1000v rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer of cross linkable ethylene propylene Rubber EPR insulation and LSZH inner bedding, steel wire arouring & LSZH outer sheath complete as required.

Supplying & laying of 2x1.5sqmm fire survival armoured cable, 600/1000v rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required.

Supplying and drawing of cable fire retardant PVC insulated copper conductor cable in the existing surface/recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required. Speaker cable single pair, 2-core, 1.5 sqmm

Supplying and fixing 25mm dia MS flexible pipe with PVC coating along with all ancillaries and accessories like coupler etc. as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25mm dia conduit

32mm dia conduit

FURNITURE WORKS : Supplying and installation of chair, make nilkamal

Supplying and installation of classic cane chair with Armrest

Supplying and installation of coffee table

ELECTRIFICATION WORKS : Wiring for light poin/ fan point/ exhaust fan point/ call bell point with 1.5sq.mm FRLS PVC insulated copper conductor single core cable in surface recessed medium class pvC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC linsulated copper conductor single core cable ete, as required. Group A

Group B

Group C

Wiring for twin control light point with 1.5 sq, mm FRLS PVC insulated lcopper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and learthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for circuitl submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2X 1.5sq.mm+1X1.5 sq.mm earth wire

2 X 2.5 sq.mm + 1 x 2.5sq.mm earth wire

2X4sq.mm +1X4 sq. mm earth wire

2X6 sq.mm +1X6 sq. mm earth wire

4X 10 sq. mm+ 2X6 sq. mm earth wire

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 A switch

15/16 A switch

3 pin 5/6 A socket outlet

Supplying and fixing 3 pin, S A ceiling rose on the existing junction box wooden block including conections ete, as required.

Suplying andfixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/ modules, Gl box along with modular base & cover plate for modular switches in recess ete. as reguired. 1 or 2 Module (75mmX75mm)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc, as reguired.6Module(200mmX75mm)

Supplying and fixing 3 pin, 5A ceiling rose on the existing junction box wooden block including conections ete, as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning ete, as required. Up to 450 mm sweep

Supplying and fixing PVC batten/ angle holder including connections etc.as required

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/lsolator) 12 way, Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve,miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, I commissioning etc. as required. testing and commissioning etc. as required. Single pole

Single pole and neutral

Supplying and fixing following rating, four pole, 4l5 V, isolator in the existing MCB DB complete with connections, testing and commissioning ete, as required, 63 A

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of I.I KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required, Up to 35 sq. mm

Earhing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X S mm G.l. strip at 0.50 metre below Lground as strip earth electrode, including connection/ terminating with G.1. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.1. nut bolt & spring washer spaced at 50mm)

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 15 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos.canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min, 350 RPM(tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C(max.), insulation resistance more than 2mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc.complete as required.

NON SHEDULED ITEMS (REFER ANNEXURE 1) Supply of LED Bulb 12 watt crompton make as specified and directed by the department

Supplying of LED batten 20 Watt Twin line Crompton/Havells/Bajaj/phillips make as specified and directed by the department

Supplying of exhaust fan 300 mm sweep etc as specified and directed by the department

Supplying with fitting of LED floodlight/security light luminaire with ultra sleek, light weight and secondary optics, made of pressure die-cast housing with IP66 ingress protection and impect resistance of IK07, 4K vinbuilt and 10KV external surge protection etc as per required and as directed by the department (Bajaj/equivalent)

Supplying with fitting of UG cable 50 sqmm 3.5 core

Supplying with Installation of Submersible pump 1HP Motor

Payment to APDCL authority load security as per present prevailing norms of APDCL

Meter security for 3 phase as per APDCL

SITE DEVELOPMENT : Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete

RCC STAGING : Earth work in excavation by mechanical I means (Hydraulic excavator) manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto I.5 m, as directed by Engineer-incharge. All kinds of soil

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level (1 cement: 2 coarse sand (zone-1II) derived from natural sources:4graded stone aggregate 20 mm nominal size derived from natural sources)

Centering and shuttering including strutting, propping etc, and removal of form work for: Foundations, footings, bases for columns

Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level ; 1cement : 1, 5 coarse sand (z0ne-1I) derived from natural sources sources)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : (1 cement: 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with birumen and G.. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.63 mm thick with zinc coating not less than 275 gm/ m²

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement: 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete

Suspended floors, roofs, landings, balconies and access platform

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Steel reinforcem ent for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

15 mm cement plaster on rough side of single or half brick wall of mix: (1 cement: 4 coarse sand)

White washing with lime to give an even shade: New work (three or more coats)

Finishing walls with Acrylic Smooth exterior paint of required shade: New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS: 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.