Providing water Supply scheme to Palgi, Dhallan, Muhan, Garsa, Railla-Rote, Bhallan, Dhara, Talara, Ronal-Donal, Kashadhi, Dari, Phallana, Kothi Chehani, Khadagad, Seri, Balagad, Tandi, Chethar, Pekhari, Sarchi, Laida, Tilroo, Thatibir, Ratwah etc

Amount

Cutting in earth work and disposal of excavated earth up to lead of 20 mtrs. in all kinds of soil in pick work, Jumper work and blasting work complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Excavation in foundations, trenches etc., in earth work , lift up to 1.50 metres stacking the excavated soil not more then 3 metres clear from the edge of excavation and then returning the stacked soil in 15 cm layers, when required in to plinths , sides of foundations etc., consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed within a lead of 20 metres in pick jumper work complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing and laying cement concrete 1:3:6 ( 1cement: 3 Sand : 6 graded stone aggregate, 40mm nominal size) and curing complete excluding cost of centring and shuttering in foundation and plinth complete in all respects with in all leads and lifts as per

Providing and laying cement concrete 1:4:8 ( 1cement: 4 Sand : 8 graded stone aggregate, 40mm nominal size) and curing complete excluding cost of centring and shuttering in foundation and plinth complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing and laying cement concrete 1:6:12 (1 cement: 6 sand: 12 graded crushed stone aggregate 40mm nominal size) and curing complete excluding cost of form work in foundation and plinth in all leads and lifts and to the enitre satisfaction of Engineer-in- charge.

Providing form work with steel plates3.15mm thick welded with Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm so as to give a fairfinish I/c centring , shuttering , strutting and proping etc.with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4m and removal of the same for insitu- reinforced concrete &plain concrete work in complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Foundation, footings basis of columns etc. and mass concrete complete in all respects with in all leads and lifts as per direction of Engineer in charge.

II) Flat surfaces such as soffits of suspended floors , roofs, landings & the like . Floors etc. up to 200 mm in thickness complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Vertical surface such as walls(any thickness) partitions and the like including attached pillasters, butteresses, plinth and string courses and the like complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Sides and Soffits of beams, beam haunchings, contiliver girders, bressumers and lintels not exceeding 1 Metre in depth in all heights from floor complete in all respect with in all leads and lifts.

In column pillars , post struts in CSrcularor curved in plain complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Edge of slab complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing from work of ordinary timber plankings so as to give a rough finish including centring,shuttering, strutting and propping etc. height of propping and centring below supporting floor to ceililng not exceeding 4 metres and removal of the same for in situ reinforced concrete and plain concrete work in:-

Arches exceeding 6 metres span complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing and laying cement concretes of minimum 1:1.5:3 (1cement:1.5 sand : 3graded stone aggregate 20mm nominal size)and curing complete excluding cost of form work and re-inforcement for reinforced concrete work in complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Foundations, footings, bases of columns and the like and mass concrete complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

in wall (any thickness but not less than 0.1 m thickness) attached pillasters, buttresses, plinth and string courses, etc. from top of foundation level upto floor two level complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

iii)Suspended floors, roofs,landings and shelves and their supports, balconies, beams, girders, bressumers and cantilivers up to floor two level complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Columns pillars , Posts etc upto floor teo level complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Beam cantiliver girders and lintels Sides and soffits of beams, beam haunchings, cantilevers, bressumers and lintels not exceeding 1 Mtr. in depth in all heights from floor complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing and laying cement concrete 1:2:4(1cement:2sand:4graded stone agg. 20mm nominal size) excluding cost of form work and reinforcement for reinforced concrete work in suspened floors, roofs,landing and shelves and their supports ,balconies, beams,girders,bressumers and cantilever upto floor two level complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Foundations, footings, bases of columns and the like and mass concrete complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Arches upto floor two level complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing in RCC work smooth finishing of the exposed surface with cement mortoe 1:3 ( 1 cement :3 sand) complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing mild steel/tor steel reinforcement including bending, binding and plaCSng in position complete up to floor two level complete in all respects with in all leads and lifts as per direction of Engineer in charge.

Steel work welded in bulit up sections, trusses and framed work i/c cutting, hoisting, fixing in position and applying priming coat of red lead paint in :- Gratting, framed guard, bars, ladders and similar work complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Brick work using common burnt clay building bricks in Super structure 1st class bricks cement mortar 1:4(1cement:4sand) with in complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Brick work using common burnt clay building bricks in foundation and plinth 2nd class bricks cement mortar 1:6 (1cement:6 sand) with in complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing wood work in frames of doors, wndows, clerestory windows and other frames wrouhgt, frramed and fixed in position in 2nd class Deodar wood within all leads and lifts as per direction & satisfaction of Engineer-in-charge.

Providing and fixing panelled glazed or panelled and glazed shutters for doors, windows and clerestory windows i/c bright finished black enammeled iron hinges with necessary screws: 2nd class deodar wood 40mm thick including entire carriage of material as per satisfaction of Engineer-in-charge.

Half brick work using common burnt clay buildings bricks in superstructure above 1st floor level in cement mortar 1:4(1cement:4sand) 2nd class bricks with in all leads and lifts.

Pointing on brick work with cement mortar 1:3 (1 cement:3 sand) with in complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.Raised & cut

6mm thick cement plaster to ceiling in CM 1:3 ( 1Cement :3 Sand) with in complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

15 mm thick cement plaster in single coat on rough side of brick/concrete stone walls for interior plastering up to floor two levels including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80 mm in girth and finished even and smooth in cement mortar 1:6 (1 cement:6 sand) with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

20 mm cement plaster in single coat on rough side of brick/stone//concrete stone walls for interior plastering up to floor two levels including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80 mm in girth and finished even and smooth in cement mortar 1:6 (1 cement:6 sand) with in all leads and lifts

Providing and fixing M.S. grills of require pattern in wooden frames of windows etc. with M.S. Flats, square or round bars with round headed bolts and nuts or by screws with in complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing and fixing wire gauge shutters using galvanised M.S.wire gauge of I.S gauge designation 8 S.G. with wire of dia 0.56mm for doors windows and clerestory windowsincluding bright finished black enamelled iron hinges with necessary screws 30mm thick 2nd class deodar wood with in all leads and lift complete in all respect

Boulder filling behind retaining wall under floor with in complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Cement concrete flooring 1:2:4(1 cement: 2 sand: 4graded stone agg. 20mm nominal size) laid in one layer finished with a floating of neat cement 40mm thick complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing 40x3mm flat iron hold fast 40cm long i.e fixing to from with 10mm dia bolts, nuts and wooden plug and embedding in cement concrete block 30x10x15cm 1:3:6 ( 1cement 3 sand 6 graded stone agg. 40mm nominal size) in complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

White washing with lime on undecorated wall surfaces(two coats) to give an even shade including thoroughly brooming the surface to remove all dust dirt & other foreign matter with in all leads and lifts as per the entire satisfaction & direction of the Engineer - in - Charge.

Distempering with dry distemper of approved brand and manufacturer (two coats) and of required shade on un-decorated wall surface to give an even shade over and including priming coat of whiting after througly brushing the surface free from mortar and other foreign matters with in all leads and lifts complete in all respect. in all leads and lifts.

Providing and fixing anodized M.S sliding door bolt anodized transparent or dyed to required colour and shade with bolts and nuts and screw complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing and fixing MS tower bolts(barrel type)anodized transparent or dyed to required shade and colour with screws etc. in complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing and fixing M.S handles anodized transparent or dyed to required colour or shade with necessary screws etc. complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts. 125mm

Applying priming coat on new wood and wood based surfaces with ready mixed paint and brushing to give an even shade including cleaning of all dirt,dust and other foreign matter with in complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Painting two coats (excluding priming coat) on new wood and wood based surfaces,with enamel paint to give an even shade including cleaningthe surface of dirt ,dust and other foreign matters sand papering and stopping with readymade paint other than white with in all leads and lifts..

Supplying and fixing rolling shutters of approved make, made of 80x1.25mm M.S. laths inter-locked together through their entire length and jointed together at the end by endlocks mounted on speCSally designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete but excluding the cost of top cove and spring shutter having width below 3.5 meters complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing Stone solling properly hand packed tightly as hand packed under floor complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing and fixing 10mm thick anti skid water proof stain and impect resistent heavy duty vetrified tiles Nitco or equivalent 600x600mmx10mm manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Supplying ,erection and installation of elephant brand 2.0 ton capacity electricity operated chain electric hoist having 5.0 mtrs lifts chai hoist confirming to IS 6547 class of duty :II with electrically operated travelling trolly head room 300 mm including all fittings girders ISMB etc in complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing plinth protection 50mm thick in cement concrete 1:3:6 (1cement: 3sand: 6 graded stone aggregate 20mm nominal size). with in all leads and lifts

Providing corrugated G.I sheet roofing fixed with galvanised iron J.or L. hooks bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers filled with white lead complete excluding the cost of purlins refters and trusses. 0.63 mm thick complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing and fixing to wall ceiling and floor galvanised mild steel tubes ( MG) including fitting and clamps including making good the wall ceiling and floor complete in all respect in all leads and lifts and to the entire satisfaction of Engineer-in-charge ..

a) 15mm nominal size

Providing and placing (at all heights) polyethylene water storage tank ISI : 12701 marked indicating the BIS License No. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes including all fittings and float valve excluding the base support for tank [Sintex, Electroplast, Star, Lotus or equivalent having valid ISI license ].complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts. 500 Ltrs. capacity

Providing and fixing vitreous china wash, down water closet (European type. W.C. pan) with integral 'P' or 'S' trap including jointing the trap with soil pipe in cement mortar 1:1 (1 cement: 1 sand). Seat and cover to be measured and paid for seperately. Anglo Indian Universal closet complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing and fixing plastic seat and cover for wash down water closet with C.P. brass hinges and rubber buffers: White plastic seat and cover, solid type complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing and fixing P.V.C. low level flushing CSstern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete.10 litre capaCSty - White complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing and fixing PVC / G.I. inlet connection for flush pipe connecting with W.C. pan complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing and fixing C.P. brass angle valve of standard design and of approved make, 15mm nominal bore in complete in all respects with in all leads and lifts as per direction of Engineer in charge.

Providing and fixing C.P. water jet including connection pipe with check nut complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing and fixing PVC pipes of 10 Kg f/Sq.cm working pressure including fittings as per requirement at site complete in all respect in all leads and lifts and to the entire satisfaction of Engineer-in-charge .110 mm OD complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Wiring for light point / fan point / exhaust fan / call bell point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required Group-B complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Wiring for CSrcuit/sub-main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No. HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

2x1.5 Sq. mm.

2x2.5 Sq. mm.

Supplying and fixing following rating Piano -type switch / Socket outlet on the exists switch box/covers including connections etc. as required complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

S.P 5/6 amps.one way switch,piano type

5 pin 15/16 amps. Socket outlet on the exists

Supply and fixing 15/16 amps. Tumbler/piano type switch on the existing switch box on the switch box/cover including connection etc. as required complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

6 Pin 15/16 amps socket outlet porcelain base / Piano type

Supplying and fixing woodern box of following size (nominal) on surface or recess with suitable size of phenolic laminated sheet cover of in front as required complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

a) 180mm x100mmx60mm deep

b) 250mmx200mmx60mm deep

Providing and fixing following type of surface mounting decorative mirror optics luminaire with powder coated CRCA sheet steel housing, low glare aluminium mirror reflector, pre-wired with 230 V starter & 36/40 w copper ballast for housing CFL (but excluding the cost of CFL), complete with all accessories, connections, testing and commissioning etc. as required. 1 x40 watt-CFL Philips make (Category-A) complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing and fixing florescent tube rod 4 feet long in the existing tube fitting as required as per speCSfication on the categoery complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Supplying and fixing ceiling rose on existing junction box/wooden block including connections etc. as required complete in all respects with in all leads and lifts as per direction of Engineer in charge.

Supplying and fixingbatten holder on existing wiring including connections etc. as required complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Supplying and fixing of following way, single pole and netural, sheet steel, MCB distribution board, 240 volts on surface/recess, complete with tinned copper busbar, netural link, earthbar, dibnbar, detachable gland plate,blanking plate, cable, identification labels interconnections, phosphatized and powder painted, including earthing etc. as required:- Single door 12 way complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Supplying and fixing 6 Amps to 32 Amps rating, 240 volts, L series miniature CSrcuit breaker of following poles in the existing MCB Db complete with connection testing and commissioning etc. as required Cat-A (single pole) complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Earthing with G.I earth pipe 4.5 mtr. long and 40mm dia, including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. ( but without charcoal or coke and salt ) complete as required complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Extra for using salt and charcoal for pipe earth electrode complete as required complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Supplying and fixing following rating, double pole, 240volts, isolator in the existing MCB DB complete with connection, testing and commissioning etc. as required 63Amp Cat-A complete in all respects with in all leads and lifts as per direction of E

Supplying and fixing LED bulb of 9 watt including testing and commissioning complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing, installing, testing and commissioning of ceilling fan and regulator i/c wiring the down rod of standard length (upto 30cm with 16/.20 mm twin twisted flexible,cotton braided copper cable including providing and fixing phenolic laminated sheet cover on the fan box and earthing etc as required. Ceiling fan 1200mm sweep Cat.-A complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing and fixing man hole cover made with angle iron 40 x40x 3 mm thick( base frame) & 30x 30x 3 mm thick top frame covered with MS sheet 6 mm thick with locking arrangements to avoid the anti soCSal activities ( lock with a set of 3 keys). ( Weight of man hole cover should not be less than 34 Kg) with in all leads and lifts

Wire crate made of G.I wire filled with boulders with square cut faces against the wire (Wire crate to be measured and paid for separately)in all leads and lifts as per the direction of Engineer-in-Charge.

Providing G.I Wire crates made of G.I.wire filled with boulders with square cut faces against the wire, (Boulder filling to be measured and paid for separately) i/c all leads and lifts. (a) G.I.Wire 5mm thick corresponding to SWG-6(15Cmx15cm.Mesh). complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing and fixing 1.80m high barbed wire fencing with angle iron posts 2.50m high 40x40x4 2.50mC/C with 9 horizontal rows and 2 diagonal rows of barbed wire embedded om C.C.1:4:8 (1cement:4sand:8graded stone agg. 20mm nominal size) complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing and fixing steel gate around Intake and storage tank complete in all respects with in all leads and lifts as per direction of Engineer in charge.

Laying and jointing of G.I pipe for ( Scour pipe) with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

32 mm dia

40 mm dia

50 mm dia

80 mm dia

100 mm dia

Providing and fixing wheel valve of all approved make following dia including all kinds of leads and lifts complete as per specification with in all leads and lifts

25mm dia.

32 mm dia

40mm dia.

50mm dia.

80 mm dia

Providing and fixing SFRC man hole cover with frame having frame size of 500 mm internal dia ( The weight of frame should not be less than 100 kg) complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing and placing in horizontal layers filtering media duly graded, screened,cleaned and washed as specified complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing and laying no fine concrete with cement concrete 1:4 ( 1 cement :4 graded stone aggrigate 20 mm Nominal size ) and curing complete excluding cost of form work in wall etc complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Top layer, Fine sand( Eff. Size 0.20mm to 0.40 and uniformity co-effiCSent 2.00 to 3.00).

Second layer, Coarse sand, 3mm - 6mm

Third layer : Bajri 6mm to 20 mm.

Fourth layer : Bajri 20mm to 25 mm

Bottom layer : Broken stone 50mm to 75 mm.

Providing & placing Precast Concrete Block in CC 1:2:4 of size 0.30 x 0.40 x 0.05 ( I cement :2 sand ;4 graded stone aggrigate 20 mm nominal size)over X Drain complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

Providing and laying cement concrete 1:5:10(1cement:5sand:10 graded stone aggregate of 40mm nominal size) with 15% plum and curing complete excluding cost of form work in retaining walls/breast walls, the size of plums shall usually be 150mm to 300mm as per H.P.P.W.D specification including all leads and lifts

Providing and fixing C.S/ C.I sluice valve ( with hand wheel ) of leader / KSB, kilburn, kirloskar /Gled & all approved make as per IS:780 Class-I upto 100 mm dia ( including brass spindal and as per IS; 2906 class- for diameters more than 80 mm complete including all allied accessories. with complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

100 mm dia

Random rubble masonry / Polygonal rubble masonry (coursed or brought to courses with hard stone of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 in cement mortar 1:6 (1 cement : 6 sand) in all leads and lifts in foundation and plinth complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.

ASHEESH DEV

Avinash

MNBN Enterprises

CHADHA MOTORS

Lalit Pal

VIKRAMJEET