Construction of Health Sub Centre at Kuhna, G.P. Kuhna, Dev. Block Pragpur, Distt. Kangra H.P. (SH- Building Portion, Civil Work, WS and SI)

Excavation by mechanical means (Hydraulic excavator) / manual means in foundation, trenches etc. in earth work in all classification of soil such as pick work, jumper work, pick jumper work, blasting work, jumper blasting work, soft and hard blasting and saturated soil, de-watering, including wedging out rocks where blasting work is prohibited, chiseling or any other mixed variety of soil, de-watering and/or removal of slush and incidentals, lift upto any heights, stacking the excavated soil not more than 3 mtrs (Three meters) clear from the edge of excavation and then retuning the stacked soil in 15cm (Fifteen centimeter)layers, when required into plinths, sides of foundation etc; consolidating each deposited layer by ramming, watering and then disposing of all excavated earth as directed by the Engineer-in-Charge, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Filling excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, as directed by the Engineer-in-Charge, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government..

Providing and laying mechanically mixed and vibrated plain cement concrete 1:4:8 (one cement isto four sand isto eight graded crushed stone aggregate 40mm (Forty millimeter) nominal size) and curing complete, in or under water, including pumping or bailing out water/dewatering, removal of slush which may arise at the time of laying under water complete excluding the cost of form work in foundation and plinth in all depths/heights as per HPPWD specifications and as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates 3.15mm (Three point one five millimeters) thick, welded with angle iron in frame 30x30x5mm (Thirty into Thirty into Five millimeters) so as to give a fair finish including centering, shuttering strutting and propping etc, with wooden battens and ballies, height of propping and centering in all heights. below supporting floor to ceiling and removal of the same for in situ reinforced concrete and plain concrete work in foundation footings, basis of columns etcetera and mass concrete, and as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates 3.15mm (Three point one five millimeters) thick, welded with angle iron in frame 30x30x5mm (Thirty into Thirty into Five millimeters) so as to give a fair finish including centering, shuttering strutting and propping etc, with wooden battens and ballies, height of propping and centering in all heights below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in Columns, pillars, posts and struts, (square, rectangular/ polygonal in plan), up to all floor level, and as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates 3.15mm (Three point one five millimeters) thick, welded with angle iron in frame 30x30x5mm (Thirty into Thirty into Five millimeters) so as to give a fair finish including centering, shuttering strutting and propping etcetra with wooden battens and ballies, height of propping and centering in all heights below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in beams cantilevers, girders and lintels, sides and soffits of beams, beam haunchings, cantilevers, bressumers and lintels upto any depth/heights, up to all floor level and as directed by the Engineer-in-Charge including carriage materials of within all leads, lifts and other incidentals. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates 3.15mm (Three decimal one five millimeters) thick, welded with angle iron in frame 30x30x5mm (Thirty into Thirty into Five millimeters) so as to give a fair finish including centering, shuttering strutting and propping etc, with wooden battens and ballies, heights of propping and centering in all heights below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in flat surfaces such as soffits of suspended floors, roofs, landings, shelves, and the like floor, etcetra up to any thickness, up to all floor level and as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates 3.15mm (Three decimal one five millimeters) thick, welded with angle iron in frame 30x30x5mm (Thirty into Thirty into Five millimeters) so as to give a fair finish including centering, shuttering strutting and propping etc, with wooden battens and ballies, height of propping and centering in all heights below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in wall (any thickness) including attached pilasters, butteresses, plinth and string courses etc. and as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates 3.15mm (Three decimal one five millimeters) thick, welded with angle iron in frame 30x30x5mm (Thirty into Thirty into Five millimeters) so as to give a fair finish including centering, shuttering strutting and propping etc, with wooden battens and ballies, heights of propping and centering in all heights below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in edges of slabs and breaks in floors and walls upto any width, up to all floor level and as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated reinforced concrete work Grade M-20 (Twenty) design mix to obtain the minimum compressive strength of 20 N/mm2 (twenty newton) per square millimeter with cement contents not less than 330 kg (three hundred thirty) Killogram per cubic meter and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in foundation footings, bases of columns etcetera and the like mass concrete complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated reinforced concrete work grade M-25 (M-Twenty five) design mix to obtain the minimum compressive strength of 25 N/mm2 (twenty five newton) per square millimeter with minimum cement contents of 400kg (Four hundred kilogrammes) per cubic metre and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in columns, pillars, piers, abutments, posts and struts etcetra up to all floor five level complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated reinforced concrete work Grade M-20 (Twenty) design mix to obtain the minimum compressive strength of 20 N/mm2 (twenty newton) per square millimeter with cement contents not less than 320 Kg (three hundred twenty) Killogramme per cubic meter and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in suspended floor roofs, landings and shelves and their supports, balconies, beams, girders, bressumers cantilevers and the like shelves and work tops etcetera in all upto all floor level complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and laying Tor steel of SAIL/ TISCO/ JINDAL/ KAMDHENU/ SHYAM STEEL reinforcement for thermo mechanically coated bars of grade Fe500D for Reinforced Cement Concrete work including bending, binding and placing in position complete including cost of binding wire and other incidentals for its completion up to all floor level complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Brick work using Second class common burnt clay F.P.S. (non modular) buildings bricks of class designation 7.5 in super-structure above plinth level upto all floor level in cement mortar 1:6 (one cement isto six sand) and curing complete as per approved drawing, design and specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Second class half brick work using common burnt clay F.P.S. (non modular) building bricks of class designation 7.5 in super structure above plinth level upto all heights/floor level in cement mortar 1:4 (one cement isto four sand) and curing complete including carriage of materials within all leads, lifts and other incidentals, as per directions and entire satisfaction of the Engineer-in-Charge. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Random rubble masonry/ polygonal rubble masonry (un-coursed/ brought to courses) with hard stones of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (One cement : six sand : twelve graded crushed/ broken stone aggregate 20mm (Twenty milimetres) nominal size) at plinth level in cement mortar 1:6 (One cement : six sand) and curing complete, including carriage of materials within all leads and lifts and other incidental charges. The rate includes, royality charges, octroi, GST sale tax, malkana and all other taxes as imposed by the Government.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete as per directions of Engineer -in -charge including carriage of materials within all leads and lifts. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Dry Stone pitching 22.05 cm thick including supply of stones and preparing surface complete as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish up to all floor level, and as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government. Granite stone shall be got approved from engineer incharge before use.

Providing edge moulding to 18 mm thick granite stone ,marble or kota stone counters, Vanities etc., including machine polishing to edge to give high gloss finish up to all floor level, and as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete up to all floor level, and as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing first class sal wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately) and other incidentals for its completion up to all floor level complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 35mm thick (thirty-five mili metres) well seasoned hollock wood glazed shutters for doors, windows and clerestory windows using 4 mm (four mili metre) thick glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws and other incidentals for its completion up to all floor level complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 35mm thick ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters including ISI marked Stainless Steel butt hinges with necessary screws and other incidentals for its completion up to all floor level complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 35mm thick (thirty-five mili metres) well seasoned hollock wood wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directionnns with wire of dia 0.63 mm, for doors, windows and clerestory windows including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws and other incidentals for its completion up to all floor level complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing 40x5 mm (Forty X five mili metres) flat iron hold fast 40 cm (forty centimetre)long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (one cement : three coarse sand : six graded stone aggregate 20mm nominal size).complete including carriage of materials within all leads, lifts and other incidentals, as per directions and entire satisfaction of the Engineer-in-Charge. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc.Fixed to openings /wooden frames with rawl plugs screws including priming coat with approved steel primer and other incidentals for its completion up to all floor level complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 300x16mm (three hundred milimetres X Sixteen milimetres) aluminium sliding door bolts, make of PILOT/Sheel anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete including carriage of materials within all leads, lifts and other incidentals, as per directions and entire satisfaction of the Engineer-in-Charge. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing and fixing 250x16mm (Two hundred fifty milimetres X Sixteen milimetres) aluminium sliding door bolts, make of PILOT/Sheel anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete including carriage of materials within all leads, lifts and other incidentals, as per directions and entire satisfaction of the Engineer-in-Charge. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing and fixing 200x10mm (Two hundred into ten millimetre) aluminium Tower bolts make of PILOT/Sheel or equivalent, ISI marked, anodised (anodic coating not less than grade AC 10 (Ten) as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete as per approved drawing, design and specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 100x10mm (One hundred into ten millimetre) aluminium Tower bolts make of PILOT/Sheel or equivalent, ISI marked, anodised (anodic coating not less than grade AC 10 (Ten) as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete as per approved drawing, design and specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 125mm (One hundred twenty five millimetre) aluminium Handles make of PILOT/Sheel or equivalent, ISI marked, anodised (anodic coating not less than grade AC 10 (Ten) as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete as per approved drawing, design and specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 100mm (One hundred millimetre) aluminium Handles make of PILOT/Sheel or equivalent, ISI marked, anodised (anodic coating not less than grade AC 10 (Ten) as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete as per approved drawing, design and specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing aluminium hanging twin rubber floor door stopper make of PILOT/Sheel or equivalent, ISI marked, anodised (anodic coating not less than grade AC 10 (Ten) as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete as per approved drawing, design and specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing bright finished brass hard drawn hooks and eyes : 150mm size complete including carriage of materials within all leads, lifts and other incidentals, as per directions and entire satisfaction of the Engineer-in-Charge. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc.complete including carriage of materials within all leads, lifts and other incidentals, as per directions and entire satisfaction of the Engineer-in-Charge. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing and laying vitrified floor tiles of Restile/ Nitco/ Rak/ Simpolo/ AGL/ Kajaria/ Johnson/ Orient bell/ Somany of 600x600x10mm (Six hundred millimetre into six hundred millimetre into ten millimetre) size manufactured of approved shade and colour with water absorption less than 0.08% (Zero point zero eight percent) and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm (Twenty millimetre) thick cement mortar 1:4 (one cement isto four coarse sand), jointing with grey cement slurry at the rate 3.3 kg/ sqm (Three point three kilogram per square metre) including grouting the joints with white cement and matching pigments etcetra complete as per approved drawing, design and specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. The sample of tiles shall be got approved from engineer incharge before use.

Providing and laying 5.5mm (five point five milimetre) thick Ceramic/Spartic glazed floor tiles of size 300x300 mm (three hundred X three hundred mili metre) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (one Cement : four Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etcetra complete as per approved drawing, design and specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. The sample of tiles shall be got approved from engineer incharge before use.

Providing and fixing 1st quality ceramic glazed wall tiles of size 300x450 mm (three hundred X four hundred fifty mili metre) Restile/ Nitco/ Rak/ Simpolo/ AGL/ Kajaria/ Johnson/ Orient bell/ Somany conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade etcetra complete as per approved drawing, design and specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. The sample of tiles shall be got approved from engineer incharge before use.

Applying priming coat with ready mixed pink or Grey primer of approved brand and manufacture (Asian Paints/Nerolac Paints/ Burger Paints/ Dulux Paints) on wood work (hard and soft wood) complete upto all floor level as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Painting wood work two or more coat with Deluxe Multi Surface Paint of required shade. applied at the rate 0.90 ltr/10 sqm (Zero point nine zero litre per ten square metre) over an under coat of primer applied at the rate 0.75 ltr/10 sqm (Zero point seven five litre per ten square metre) of approved brand and manufacture as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and applying 6mm (six millimeter) thick cement plaster to ceiling with cement mortar 1:3 (one cement isto three sand), up to all floor level complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and applying 15mm (fifteen millimeters) thick cement plaster with cement mortar 1:6 (one cement isto six sand) in single coat on rough side of brick/concrete/ stone walls for interior plastering up to all floor level including arises, internal rounded angles, chamfers and/or rounded angles in all girth and finished even and smooth as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and applying 15mm (fifteen millimeters) thick cement plaster with cement mortar 1:6 (one cement isto six sand) in single coat on fair side of brick/concrete/ stone walls for interior plastering up to all floor level including arises, internal rounded angles, chamfers and/or rounded angles in all girth and finished even and smooth as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and applying white cement based putty of average thickness 1mm (One millimtre), of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete upto all floor level as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Distempering two coats with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 (fifty) grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour complete upto all floor level as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Finishing walls with Acrylic Smooth exterior paint of required shade on New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete upto all floor level as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Making plinth protection 50mm (Fifty millimeters)thick of cement concrete 1:3:6 (One cement : Three coarse sand (zone - III) : Six graded stone aggregate 20 mm nominal size) over 75mm (Seventy five millimeters)thick bed of dry brick ballast 40 mm(Forty millimeters) nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth and carriage of material within all leads and lifts.

Providing and fixing white vitreous china water closet European type W.C. pan of Star No. 20087 (S-10) of size 58x44cm (Fifty eight into fourty four centimeter) with PVC cistern (Sleek plus) and fixed with jet pressure of Hindware/ Cera/ Jaquar of Star white/snow white shade with seat and lid, 10 (Ten) litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required all complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other ncidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 55x40cm (Fifty fife into forty centimetre) wash basin with cast iron brackets, 15mm (Fifteen millimetre) chromium plated brass pilar taps, 32mm (Thirty two millimetre) chromium plated brass waste of standard pattern of Hindware/ Cera/ Jaquar of Star white/snow white shade matrix wash basin , including painting of fittings and brackets, cutting and making good the walls wherever require complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other ncidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing white vitreous china pedestal for wash basin of Hindware/ Cera/ Jaquar of Star white/snow white shade completely recessed at the back for the reception of pipes and fittings complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other ncidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 610x510x200mm (Six hundred ten into five hundred ten into two hundred millimeter) Stainless Steel A ISI 304 (18/8) kitchen sink ISI marked make of Cera or its equvalent as per IS:13983 with C.I. brackets and stainless steel plug 40 mm (Forty millimeter) , including painting of fittings and brackets, cutting and making good the walls wherever required complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other ncidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing white vitreous china squatting plate urinal of Hindware/ Cera/ Jaquar of Star white/snow white shade with integral rim longitudinal flush pipe complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other ncidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing P.V.C. waste pipe 32mm dia fitting complete for sink or wash basin including P.V.C. waste fittings complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other ncidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing PVC (Polyvinyl chloride) floor trap make of Finolex/ Relpipe (Reliance)/Vectus approved manufacture self cleaning design including fixing with approved adhesive, cost of cutting making good the wall complete 110X90 mm ( one hundred ten into Ninety millimeter) as per approved drawing, design and specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 600x450mm (Six hundred into four hundred fifty) beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other ncidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 600x120x5mm (Six hundred into one hundred twenty into five millimeter) glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. (Chromium plated) brass brackets and guard rail complete fixed with 40mm (Forty millimeter) long screws, rawl plugs etcetra complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other ncidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing chromium plated brass toilet paper holder of Continental series of Jaquar/ Classic series of Hindware/ Floral series of Cera/ Vintage series of Kerovite/ Hindon series of JAL including necessary fittings complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other ncidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 110mm (One hundred ten millimetre) diametre high pressure P.V.C. (Poly vinyl chloride) spigot and socket soil, waste and ventilating pipes ISI marked confirming to IS-14735-99 medium class make of Finolex/ Relpipe (Reliance)/Vectus approved manufacture including fixing with approved adhesive etcetra complete as per approved drawing, design and specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 75mm (seventy five millimetre) diametre high pressure P.V.C. (Poly vinyl chloride) spigot and socket soil, waste and ventilating pipes ISI marked confirming to IS-14735-99 medium class make of Finolex/ Relpipe (Reliance)/Vectus approved manufacture including fixing with approved adhesive etcetra complete as per approved drawing, design and specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 110mm (Two hundred ten millimeter) diameter PVC (Polyvinyl chloride) (D-Plast) plain bend ISI marked make of Finolex/ Relpipe (Reliance)/Vectus approved manufacture with insertion rubber washer, 3mm (Three millimeter) thick bolts and nuts, including testing of pipes and joints complete as per approved specifications, design, drawing, as per the directions and entire satisfaction of the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental Charges. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing and fixing 75mm (seventy five millimeter) diameter PVC (Polyvinyl chloride) (D-Plast) plain bend ISI marked make of Finolex/ Relpipe (Reliance)/Vectus approved manufacture with insertion rubber washer, 3mm (Three millimeter) thick bolts and nuts, including testing of pipes and joints complete as per approved specifications, design, drawing, as per the directions and entire satisfaction of the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental Charges. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing and fixing 110mm (Two hundred ten millimeter) diameter PVC (Polyvinyl chloride) (D-Plast) door bend ISI marked make of Finolex/ Relpipe (Reliance)/Vectus approved manufacture with insertion rubber washer, 3mm (Three millimeter) thick bolts and nuts, including testing of pipes and joints complete as per approved specifications, design, drawing, as per the directions and entire satisfaction of the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental Charges. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing and fixing 75mm (seventy five millimeter) diameter PVC (Polyvinyl chloride) (D-Plast) door bend ISI marked make of Finolex/ Relpipe (Reliance)/Vectus approved manufacture with insertion rubber washer, 3mm (Three millimeter) thick bolts and nuts, including testing of pipes and joints complete as per approved specifications, design, drawing, as per the directions and entire satisfaction of the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental Charges. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing and fixing 110mm (Two hundred ten millimeter) diameter PVC (Polyvinyl chloride) (D-Plast) single equal branch with ovel access door ISI marked make of Finolex/ Relpipe (Reliance)/Vectus approved manufacture with insertion rubber washer, 3mm (Three millimeter) thick bolts and nuts, including testing of pipes and joints complete as per approved specifications, design, drawing, as per the directions and entire satisfaction of the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental Charges. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing and fixing 75mm (seventy five millimeter) diameter PVC (Polyvinyl chloride) (D-Plast) single equal branch with ovel access door ISI marked make of Finolex/ Relpipe (Reliance)/Vectus approved manufacture with insertion rubber washer, 3mm (Three millimeter) thick bolts and nuts, including testing of pipes and joints complete as per approved specifications, design, drawing, as per the directions and entire satisfaction of the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental Charges. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing and fixing 110mm (Two hundred ten millimeter) diameter PVC (Polyvinyl chloride) (D-Plast) Collar ISI marked make of Finolex/ Relpipe (Reliance)/Vectus approved manufacture with insertion rubber washer, 3mm (Three millimeter) thick bolts and nuts, including testing of pipes and joints complete as per approved specifications, design, drawing, as per the directions and entire satisfaction of the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental Charges. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing and fixing 75mm (seventy five millimeter) diameter PVC (Polyvinyl chloride) (D-Plast) Collar ISI marked make of Finolex/ Relpipe (Reliance)/Vectus approved manufacture with insertion rubber washer, 3mm (Three millimeter) thick bolts and nuts, including testing of pipes and joints complete as per approved specifications, design, drawing, as per the directions and entire satisfaction of the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental Charges. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing and fixing PVC Clamps ISI Marked of approved design with steel screw and rawal plug etc.complete :-110 mm dia complete as per approved specifications, design, drawing, as per the directions and entire satisfaction of the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental Charges. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing and fixing PVC Clamps ISI Marked of approved design with steel screw and rawal plug etc.complete :-75 mm dia complete as per approved specifications, design, drawing, as per the directions and entire satisfaction of the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental Charges. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing and fixing PTMT soap dish of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighting not less than 105 gms.complete as per approved specifications, design, drawing, as per the directions and entire satisfaction of the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental Charges. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass scews with concealed fitting arrangement of approved quality and colour, 600mm long towel rail with total lenth of 645mm,with 78mm and effective height of 88mm, weighing not less than 190 gms.complete as per approved specifications, design, drawing, as per the directions and entire satisfaction of the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental Charges. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing and fixing 16mm (sixteen millimeter) nominal bore/diameter 1216 (One thousand two hundred sixteen) Polyethelene-Aluminium-Polyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C (Eighty degree celsius), including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 (One) metre spacing. This includes the costs of cutting chases and including testing of joints complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other ncidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 20mm (Twenty millimeter) nominal bore/diameter 1620 (One thousand six hundred twenty) Polyethelene-Aluminium-Polyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C (Eighty degree celsius), including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 (One) metre spacing. This includes the costs of cutting chases and including testing of joints complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other ncidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Making connection of galvanised steel distribution branch with galvanised steel mail 25mm to 40 mm (twenty five to forty milimeter) nominal bore by providing and fixing tee including cutting and threading the pipe complete as per approved drawing, design and specifications and as per direction and entire satisfaction of Engineer-in-Charge, including carriage of material within all leads, lifts and other incidentals. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing and fixing 25mm (Twenty five millimetre) nominal bore brass ferrule with cast iron mouth cover including boring and tapping the main complete as per approved drawing, design and specifications and as per direction and entire satisfaction of Engineer-in-Charge, including carriage of material within all leads, lifts and other incidentals. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing and fixing ISI marked 45cm (forty five centimeters) long and 15mm (fifteen millimeters) nominal bore uplasticised PVC connection pipe with brass unions complete as per approved drawing, design and specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 15mm (fifteen millimetre) nominal bore brass ball valve of approved quality, High or low pressure, with plastic floats complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 20mm (Twenty millimetre) nominal bore brass ball valve of approved quality, High or low pressure, with plastic floats complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing C.P. (Chromium plated) 15mm (Fifteen millimetre) nominal bore brass bib tap of Continental series of Jaquar/ Classic series of Hindware/ Floral series of Cera/ Vintage series of Kerovite/ Hindon series of JAL of approved manufacture conforming to IS:8931 complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing C.P. (Chromium plated) 15mm (Fifteen millimetre) nominal bore brass long body bib cock of Continental series of Jaquar/ Classic series of Hindware/ Floral series of Cera/ Vintage series of Kerovite/ Hindon series of JAL of approved manufacture conforming to IS standards and weighing not less than 690 gms (Six hundred ninety gram) as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing C.P. (Chromium plated) 15mm (Fifteen millimetre) nominal bore brass stop cock ( concealed) of Continental series of Jaquar/ Classic series of Hindware/ Floral series of Cera/ Vintage series of Kerovite/ Hindon series of JAL of approved manufacture conforming to IS standards and weighing not less than 690 gms (Six hundred ninety gram) as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing C.P. (Chromium plated) 15mm (Fifteen millimetre) nominal bore brass angle valve of Continental series of Jaquar/ Classic series of Hindware/ Floral series of Cera/ Vintage series of Kerovite/ Hindon series of JAL of approved manufacture for basin mixer and geyser points of approved quality conforming to IS:8931 as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and placing three layered PVC (Poly Venyl Chloride) water storage tank ISI marked 12701 (Twelve thousand seven hundred one) Sintex or its equivalent make and of having capacity 1000 ltr. (One thousand liters) tank complete in all respects, with necessary fittings including over flow pipe ball valve, scour pipe, with polythene float valve, PVC cover with locking arrangement including proving pads of sizes as required for inlet and outlet complete as per approved drawing, design and specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 Fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Please Enable Macros to View BoQ information