Construction of Prefab Hut of Chowkidar Room with Mini Office for Campus to University of Jammu at Rakhi-Aarath Budgam

Earth work in excavation by mechanicall means in trenches for foundations, drains, pipes, cables etc.upto required depthh and size, including dressing of sides and ramming of bottoms, including getting out excavated earth and disposal of surplus excavated earth as directed in all kinds of soil

Providing and laying of stone soling, hand packed, including carriage of same from approved source upto site of work complete.

P/ L in position cement concrete in 1:4:8(1 cement :4 coarse sand : 8 graded crushed stone aggregate, 40mm nominal size) excluding the cost of centering and shuttering but including carriage(30km) of all materials from approved sources up to site of work complete.

Providing and laying in position cement concrete of specified grade including curing butexcluding the cost of centring and shuttering. All work upto plinth level with:1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforcement for RCC work including straightening cutting, bending, placing in position and binding all complete (Thermo mechanically treated bars) including all carriages complete.

Centering & shuttering including strutting, propping etc including removal of form work.

Foundations, footings, bases for columns, plinth

Suspended floors, roofs, landings, balconies and access platforms.

Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. including cost and carriage of all material involved complete. 50 mm thick with 20mm nominal size stone aggregate.

Supplying and filling in plinth with RBM/NALLAH MUCK including top 1'0" with fine sand under floors including, watering, ramming, consolidating and dressing complete.

Brick work with common burnt clay F.P.S (non modular) bricks of class designation 75 in superstructure above plinth level upto floor V level in all shapes and sizes in :(Cement mortar 1 : 6 (1 cement : 6 coarse sand) excluding cost and carriage of all material involved complete.

12mm Cement plaster of mix:13.1.2 1 : 6 ( 1 cement : 6 fine sand)

Supplying & Installation of Pre-fabricated structural steel work in built up sections of square,round or rectangular sections including cutting, hoisting and placing in position with the bolts, scraped in concrete band & applying a primer coat of approved steel primer etc, incl. covering of frame workwith PUF panels of 75 mm thick layer of rigid CFC free close cell, polyurethane foam of density 40kg (+,-2kg)/Cum filled in high rib profiled SMP coated sheets for walls etc. & 40 mm thick PUF panel in ceiling etc. (Complete job, Finished work measured).TECHNICAL SPECIFICATIONS FOR PRE-FAB STRUCTURE MADE UP OF STEEL AND PUF PANELLS IN WALLS WITH ATTACHED TOILET.Pre-Fabricated shelter made up of steel structure and PUF panels, colour coated profile sheets etc withh technical specification as given below: Design Parameter. a) Seismic=Zone V b) Wind/snow load as per relevant IS codes for the region c) Temperature Range(-) 40 to (+) 50C d) Roof slope= 1:2 e) Dimensions. All as indicated in the reference drawing to be provided as site or as directed by EIC at site 2. Technical Specifications a) Details of Structural Members. The steel structure for the shelters will be designed for the Designed Paramater.All structural steel will be ISI marked with manufacturers test certificate for raw material and structural properties. The main columns, verandah rafters, trusses, purlins etc will be made out of steel sections, MS plates, MS bolts /nuts b) The roof will be provided with 0.50 mm thick Pre-colour coated steel profile sheets. Sheet covering will be fixed with using hot dip zinc coated self drilling hexagonal washer head fasteners. Ridge shall be covered by 0.50 mm thick Pre-colour coated steel sheet. The sheets shall be laid with minimum end and side lap of 150mm c) Gable End. Gable End will be covered with same panels as of wall upto bottom chord of truss. The triangular truss portion will be covered with 0.50mm wider than the width of the opening d) Sunshades. Suitable sunshades made out of colour coated sheet reinforced with angle iron frame will be provided to external windows and doors as directed by EIC as per requirement. e) Roof Projection. The roof will have minimum projection 450mm to 600mm all around including verandah portion. Purlins will also be extended in the roof at the eaves and at gable roof extension (outside the structure) f) Main walls & partition walls. The main and partition walls will be made up of 75 mm thick wall Panels having height of 3.0 mtrs of make Llod panel system /Modern Panels/Jindal Mectecnol/PSL Engineering or equivalent. The Panels will be made of 0.50mm thick hot dipped galvanized steel sheets on both sides with 60mm thick layer of rigid CFC free close cell polyurethane foam (Density 40 Kg+2 Kg/Cum) insulation. The wall panels will be provided with tongue and groove joint and will be with cam lock/ continuous paneling systems tor interlocking. All materials required for the manufacture of shelter will be new and shall comply with relevant Bureau of Indian Standard Specification. Base channel of specified size will be provided for walls. The PUF insulation material in the panel will have fire retarding and self extinguishing properties as per any international standard B2 DIN 4102 Part-l/BS-4735 Self Ext. g) Ceiling. The false ceiling of Rooms, Toilets and verandah will be made up of 40 mm thick PUF insulated Panels of Make Lloyd Panel system/Modern Panels/Jindal Mectechno/PSL Engineering or equivalent. The Panels will be made of 0.50 mm thick hot dipped galvanized steel sheets on both side with 40mm thick layer of rigid CFC free close cell polyurethane foam (Density 40 Kg+ 2 Kg/Cum) insulation. The false ceiling panels will be provided with tongue and groove or lip locking joint for interlocking. False ceiling will be supported with the help of inverted CRCA Tee Section 50x50x5 mm thick and L-Section of 50x50x5 mm thick fixed appropriately to the Truss. h) ceiling : Shall consist of 19 mm thick ply boards of ISI make laid over Structural steel network as designed and directed at Site. i) Windows. Aluminum profile sliding windows with all fitments will be provided and fixed in position by the contractor as directed by EIC The window shutter will be of two leaves of which one shall be provided with glazing of 4mm intello reflective glass and one leaf will be provided with fixed fly proofing using stainless steel mesh of 1.5mm aperture. j) Doors. Doors will be provided and fixed in positlon by the contractor as directed by EIC in each shelter. Door frames and shutters will be made up of suitable flush door sections. Main shutter will be provided with flush both sides teak ply inserts of appropriate thickness and Fly proof shutter provided on outside of the door using stainless steel mesh of average 1.50mm aperture. The main door shall be provided with Aldrop, Two Nos Aluminum tower bolts of 200mm size from inside and one sliding bolt 300mm long and one bow handle 150mm size to be provided on both in and out side of each shutter. Internal doórs if any will not be provided with fly proof shutters k) Ventilators. Ventilator of size 450x300mm and of suitable aluminium profile section will be provided and fixed in position by the contractor as directed by the ElC in each shelter. Ventilator will have full stainless steel fly proof mesh of 1.50mm aperture and will have top hinged glazed polycarbonate sheet shutter on inside. 3. Workmanship: (a) Connection. Welded connection will be provided unless otherwise specified by EIC. The welded connections will be conformed to IS 806-1968(b) Fabrication. The general provisions in section 11 of IS 800 of 1984 will apply to all types of steel being used for fabrication.(c) All steel members will be provided with 2 coats of red oxide zinc chromate primer before supply. (d) Various Fasteners and Fittings:- Fasteners and fittings of mild steel shall be supplied unless otherwise specified in and shall be fixed where required. Fastening means will be provided for the items to be fitted at the time of erection.10% spare nuts, bolts and washers will be provided per shelter. The fasteners supplied shall conform to relevant BIS specification. Finishes. All steel work will be given two coats of red oxide zinc chromate primer and all exposed timber parts will be given two coats of wood primer by the manufacturer in the factory. Eight Liters of red oxide zinc chromate primer and twenty liters white colour paint with appropriate colour stainer per shelter will be provided in sealed containers for retouching and painting after erection. All paint material will be of Jenson & Nicholson/Berger/Asian make or equivalent. electrification viz wiring led lights switches required ceiling fan three pin sockets hook MCB complete electrification made functional inside structure area of structure 43'6''x74'10'' 3255.235sft

e) Roof Projection. The roof will have minimum projection 450mm to 600mm all around including verandah portion. Purlins will also be extended in the roof at the eaves and at gable roof extension (outside the structure) f) Main walls & partition walls. The main and partition walls will be made up of 75 mm thick wall Panels having height of 3.0 mtrs of make Llod panel system /Modern Panels/Jindal Mectecnol/PSL Engineering or equivalent. The Panels will be made of 0.50mm thick hot dipped galvanized steel sheets on both sides with 60mm thick layer of rigid CFC free close cell polyurethane foam (Density 40 Kg+2 Kg/Cum) insulation. The wall panels will be provided with tongue and groove joint and will be with cam lock/ continuous paneling systems tor interlocking. All materials required for the manufacture of shelter will be new and shall comply with relevant Bureau of Indian Standard Specification. Base channel of specified size will be provided for walls. The PUF insulation material in the panel will have fire retarding and self extinguishing properties as per any international standard B2 DIN 4102 Part-l/BS-4735 Self Ext. g) Ceiling. The false ceiling of Rooms, Toilets and verandah will be made up of 40 mm thick PUF insulated Panels of Make Lloyd Panel system/Modern Panels/Jindal Mectechno/PSL Engineering or equivalent. The Panels will be made of 0.50 mm thick hot dipped galvanized steel sheets on both side with 40mm thick layer of rigid CFC free close cell polyurethane foam (Density 40 Kg+ 2 Kg/Cum) insulation. The false ceiling panels will be provided with tongue and groove or lip locking joint for interlocking. False ceiling will be supported with the help of inverted CRCA Tee Section 50x50x5 mm thick and L-Section of 50x50x5 mm thick fixed appropriately to the Truss. h) ceiling : Shall consist of 19 mm thick ply boards of ISI make laid over Structural steel network as designed and directed at Site. i) Windows. Aluminum profile sliding windows with all fitments will be provided and fixed in position by the contractor as directed by EIC The window shutter will be of two leaves of which one shall be provided with glazing of 4mm intello reflective glass and one leaf will be provided with fixed fly proofing using stainless steel mesh of 1.5mm aperture. j) Doors. Doors will be provided and fixed in positlon by the contractor as directed by EIC in each shelter. Door frames and shutters will be made up of suitable flush door sections. Main shutter will be provided with flush both sides teak ply inserts of appropriate thickness and Fly proof shutter provided on outside of the door using stainless steel mesh of average 1.50mm aperture. The main door shall be provided with Aldrop, Two Nos Aluminum tower bolts of 200mm size from inside and one sliding bolt 300mm long and one bow handle 150mm size to be provided on both in and out side of each shutter. Internal doórs if any will not be provided with fly proof shutters k) Ventilators. Ventilator of size 450x300mm and of suitable aluminium profile section will be provided and fixed in position by the contractor as directed by the ElC in each shelter. Ventilator will have full stainless steel fly proof mesh of 1.50mm aperture and will have top hinged glazed polycarbonate sheet shutter on inside. 3. Workmanship: (a) Connection. Welded connection will be provided unless otherwise specified by EIC. The welded connections will be conformed to IS 806-1968(b) Fabrication. The general provisions in section 11 of IS 800 of 1984 will apply to all types of steel being used for fabrication.(c) All steel members will be provided with 2 coats of red oxide zinc chromate primer before supply. (d) Various Fasteners and Fittings:- Fasteners and fittings of mild steel shall be supplied unless otherwise specified in and shall be fixed where required. Fastening means will be provided for the items to be fitted at the time of erection.10% spare nuts, bolts and washers will be provided per shelter. The fasteners supplied shall conform to relevant BIS specification. Finishes. All steel work will be given two coats of red oxide zinc chromate primer and all exposed timber parts will be given two coats of wood primer by the manufacturer in the factory. Eight Liters of red oxide zinc chromate primer and twenty liters white colour paint with appropriate colour stainer per shelter will be provided in sealed containers for retouching and painting after erection. All paint material will be of Jenson & Nicholson/Berger/Asian make or equivalent. electrification viz wiring led lights switches required ceiling fan three pin sockets hook MCB complete electrification made functional inside structure area of structure 35'6''x68'10'' = 2443.465sft

with fixed fly proofing using stainless steel mesh of 1.5mm aperture. j) Doors. Doors will be provided and fixed in positlon by the contractor as directed by EIC in each shelter. Door frames and shutters will be made up of suitable flush door sections. Main shutter will be provided with flush both sides teak ply inserts of appropriate thickness and Fly proof shutter provided on outside of the door using stainless steel mesh of average 1.50mm aperture. The main door shall be provided with Aldrop, Two Nos Aluminum tower bolts of 200mm size from inside and one sliding bolt 300mm long and one bow handle 150mm size to be provided on both in and out side of each shutter. Internal doórs if any will not be provided with fly proof shutters k) Ventilators. Ventilator of size 450x300mm and of suitable aluminium profile section will be provided and fixed in position by the contractor as directed by the ElC in each shelter. Ventilator will have full stainless steel fly proof mesh of 1.50mm aperture and will have top hinged glazed polycarbonate sheet shutter on 3. Workmanship: (a) Connection. Welded connection will be provided unless otherwise specified by EIC. The welded connections will be conformed to IS 806-1968(b) Fabrication. The general provisions in section 11 of IS 800 of 1984 will apply to all types of steel being used for fabrication.(c) All steel members will be provided with 2 coats of red oxide zinc chromate primer before supply. (d) Various Fasteners and Fittings:- Fasteners and fittings of mild steel shall be supplied unless otherwise specified in and shall be fixed where required. Fastening means will be provided for the items to be fitted at the time of erection.10% spare nuts, bolts and washers will be provided per shelter. The fasteners supplied shall conform to relevant BIS specification. Finishes. All steel work will be given two coats of red oxide zinc chromate primer and all exposed timber parts will be given two coats of wood primer by the manufacturer in the factory. Eight Liters of red oxide zinc chromate primer and twenty liters white colour paint with appropriate colour stainer per shelter will be provided in sealed containers for retouching and painting after erection. All paint material will be of Jenson & Nicholson/Berger/Asian make or equivalent. electrification viz wiring led lights switches required ceiling fan three pin sockets hook MCB complete electrification made functional inside structure area of structure 35'6''x68'10'' = 2443.465sft

Providing and laying gang saw cut of specified thickness, mirror polished pre- moulded and pre polished machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring in road side plazas and similar locations, laid over 20mm thick base of cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. complete as per direction of Engineer-in Charge. 18 mm thick

Providing and laying vitrtified Glazed Ceramic floor tiles of size 600x600 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, laid on 20 mm thick cement mortar 1:4 (1Cement : 4 Coarse sand), including grouting the joints with white cement and matching pigments etc., complete. In all colours, shades, except White, Ivory, Fume Red Brown

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement :3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 MM SAND cast iron P or S Trap,10 liter low levelwhite P.V.C Flushing Cistern,including flush pipe,with manually controlled device(handle Lever),with all fittings and fixtures complete,including cutting and making good the walls and floors wherever required. White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required :18.7.1 White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete

Providing and fixing toilet paper holder with Flap made out of C.P BrassMakes:-Jaquar/Hindware/Cera

Providing and fixing C.P Brass Soap Dish.Makes:- Jaquar/Hindware/Cera

Providing and fixing CP brass towel rail complete with CP brackets fixed to wooden cleats with CP brass screws Makes:- Jaquar/Hindware/Cera

Providing and fixing C.P brass bib cock with Auto closing System with Built in control Cock with Wall Flange of approved quality Makes:-Hindware/Jaquar/Cera (15 mm nominal bore)

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 (15 mm nominal bore)

P/F of 100 mm dia PVC Plain Bend

P/F of PVC Collar complete 100 mm

P/F of 75 mm dia PVC floor trap of approved quality

P/F of CP angle valve of approved quality 15 mm dia

Providing and fixing soil, waste and vent pipes IS 13592 & fittings (IS: 14735 ) suitable to rubber ring joints , which includes bends, rubber ring, jointing, junctions, clean out plug , cowls, offsets, collar, M.S holder-bat clamps, access pieces, trap of self cleansing design .etc. complete including jointing

75 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-B

Providing and Fixing of Floor Traps 110 mm with double chrome plated Cover one Grated and one closed and all other fittings required.Makes:- Astral/SFMC/Finolex

Providing and Fixing G.I pipe complete with G.I fittings, clamps incl. cutting and making good walls etc complete ( internal/ external)

Providing and fixing on wall 50 LTRS Electric Geyser with ABS Body. Makes:- Bajaj/Crompton/Jaquar/Hindware/venus

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. including ball cock valve 8000 LTRS

Supplying and fixing C.I. cover 300x300 mm without frame for gully trap (standard pattern) the weight of cover to be not less than 4.5kg.

Carriage of materails by MT, from source to site of work

Stone agg av lead 10 km

Sand av. lead of 20 km

Bricks av. lead of 10 km