S.R. to Building Works

(with brief specification and reference to book of Quantity Unit Rate Amount

specifications)

[1] Excavation for foundation upto 1.5 m depth including sorting 62.50 Cum 117.08

out and stacking of useful materials and disposing off the

excavated stuff upto 50 Meter lead. (A) Loose or soft soil

[2] Excavation for foundation for depth from 1.5 m to 3.0 m 17.50 Cum 129.82

including sorting out and stacking of useful materials and

disposing off the excavated stuff upto 50 Meter lead. (A) Loose

or soft soil

[3] Providing and laying cement concrete 1:4:8 (1- Cement : 4- 10.50 Cum 2680.21

coarse sand : 8- hand broken stone aggregates 40 mm nominal

size) and curing complete excluding cost of formwork in (A)

Foundation and Plinth

[4] Providing and laying cement concrete work 1:2:4 (1- Cement : 2- 20.00 Cum 3917.36

Coarse sand : 4- graded stone aggregates 20 mm nominal size)

and curing complete excluding cost of formwork and

reinforcement for reinforced concrete work in (A) Foundations,

footings, Base or columns and Mass concrete

[5] Providing and laying cement concrete work 1:2:4 (1- Cement : 2- 4.50 Cum 4007.20

Coarse sand : 4- graded stone aggregates 20 mm nominal size)

and curing complete excluding cost of formwork and

reinforcement for reinforced concrete work in (D) Columns,

Pillars posts and struts upto floor two level.

[6] Filling available excavated earth (excluding rock) in trenches. 50.00 Cum 130.39

plinth, sides of foundations etc. in layers not exceeding 20 cm. in

depth consolidating each disposited layer by ramming and

[7] Brick work using common burnt clay building bricks having 35.00 Cum 4284.12

crushing strength not less than 35 kg./Sq.Cm. in foundation and

plinth in Cement Mortar 1:6 (1- Cement : 6 -fine sand) (A)

[8] 20mm thick sand faced cement plaster on walls upto height 10 613.00 Sqm 335.65

metres above ground level consisting of 12mm thick backing

coat of C.M. 1:3 (1-cement : 3-sand) and 8mm thick finishing

coat of C.M. 1:1 (1-cement : 1-sand) etc. complete.

[9] Finishing wall with weather proof exterior emulsion paint on 5314.00 Sqm 114.53

wall surface (two coats) to give an required shape even shade

after thoroughly brushing the surface to remove all dirt, and

remains of loose powdered materials.etc complete

[10] Providing TMT Bar FE 500D reinforcement for R.C.C. work 2120.00 KG 76.21

including bending, binding and placing in position complete

upto floor two level

[11] Earthwork for embankment including breaking clods, dressing 220.00 Cum 169.44

with all lead and lift and including watering rolling and

consolidation of subgrade in layers at O.M.C. to required dry

density including filling the depression which occur during the

process using power roller 8T to 10T. (E) From Borrow area

within 3.0KM. lead

[12] Demolition of Brick work and stone masonry including stacking 41.00 Cum 536.09

of serviceable materilas and disposal of unserviceable materials

with all lead and lift. (ii) In Cement Mortar.

[13] Demolition including stacking of serviceable materilas and 19.60 Cum 1030.81

disposal of unserviceable materials with all lead and lift. (i)

R.C.C. work

Description of Item

(with brief specification and reference to book of Quantity Unit Rate Amount

specifications)

[14] Applying two coats of two component dampproof coating of 622.00 Sq.m 295.63

approved brand and manufacture on undecorated wall surface

to give an even shade including throughly brushing the surface

free from mortar droppings and other foreign matter and sand

papered smooth as per instruction of Engineer In Charge.

[15] Applying general insecticide pest control treatment to floors, 688.00 Sq.m 88.92

cupboards etc including labour materials etc. complete. Using

Imidacloprid 30.5 SCas Per IS 6313 part -II ( (0.075%

concentration by mass) is recommended 10.5ml chemical

diluted with 5 liters of water application 0.5 litre chemical

/Sqm of surface is recommended as per I.S.

[16] Removing dry or oil bound distemper by a washing and 281.00 Sq.m 10.99

scraping and sand papering the wall surface smooth including

necessary repairs to scratches complete.

[17] Applying two coats of lappy (putty) and two coats of approved 1033.00 Sq.m 40.59

brand and manufacture on new wall surface to give as even

shade including thoroughly brushing the surface free from

mortar dropping and other foreign matter and sand paper

[18] Distempering (Three coats) with oil bound washable distemper 1033.00 Sq.m 101.66

of approved brand and manufacture and of required shade on

wall surfaces to give and even shade over and including a

primer coat with alkali resistance primer of approved brand

after thoroughly brushing the surface to give an even shade free

from mortar droppings and other foreign matter and also

including preparing the surface even and smooth for all floor

etc. complete.

[19] Dismantling santtary fittings like wash basin . W.C. pan Indian 74.00 Nos 394.51

and European type, flushing tank etc. including stacking the

materials with all lead and lift.

[20] Providing and fixing Flush tank of approved quality with all 4.00 Each 684.75

necessary connections with inlet, outlet and overflow etc.

including all labour and materials as directed by engineer in

[21] Providing & Fixing Premium quality approved make like Jaquar 6.00 No 4015.38

/ ESSCO or equivalent Quarter Turn Pillar Cock for Basin

including labour, material, trasportation etc. complete as

directed by engineer incharge.

[22] Providing and fixing post and pipe railing as per detailed 14.20 Rmt 1202.80

drawing including 3 coats of painting to steel works complete.

[23] Providing laying and jointing in true line and level 40mm dia. 35.00 Rmt 148.12

U.P.V.C. Pipe (SCH- 40) for cold water including fittings as

approved by Engineer In Charge. Pipe shall be fixed on the wall

with the help of clamp at every two metre C/C or shall be

concealed as directed including necessary fittings etc. including

testing of pipe and joints and fixing the same with adhesive

solvent, including cost of all materials.

[24] Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 134.00 Rmt 336.24

working pressure poluthene pipes of the following outside Dia.

Low densidy, complete with special falnge compression type

fittings, wall clipsetc. including making good the wall ceiling

and floor. (G) 110 mm

[25] Providing and fixing standared extruded of alluminium section 4.10 Sq.m 4209.24

of size 63.50 x 38.10 x 1.95 mm @ Wt 1.094 Kg/Rmt. with

colour Powder Coated alluminium frame with 5 mm thick

bakelite sheet shutter with steel hinge, handles and necessary

fixtures and fastenings etc. complete for Door.

Description of Item

(with brief specification and reference to book of Quantity Unit Rate Amount

specifications)

[26] Repairing to Door / Window including dissembling from frame, 39.00 Sqm 567.79

wroughting, providing patti, angles, replacing / repairing

stoppers - aldrops - handles etc. for proper fixing in to frame

hole etc. complete for smooth operation and proper utilization

including assambeling and refixing of the same as directed by

Engineer-in-charge.

[27] Providing and fixing screw down bib taps of following size. (B) 49.00 Each 214.81

Brass chromium plated screws down Bib Tap. (ii) 20mm dia.

[28] Providing and fixing Health Fauset Heavy duty with hook with 4.00 No 582.03

fitting including all labour and materials as directed by engineer

in charge.

[29] Providing and fixing M.I. fisher union for washbasin or sink. (B) 7.00 No 88.65

[30] Providing and fixing M.S. grills of required pattern to wooden 356.00 KG 101.17

frames of windows etc. with M.S. flats at required spacings and

frame alround, square or round bars with round headed bolts

and nuts or by screws. (A) Plain Grill.

[31] Rehabilitation of RCC Structure including removal of cement 171.00 Sqm 754.19

plaster spallad, loose and disintegrated concrete with Cleaning

the surface of the cement concrete and reinforcement from all

the loose materials with wire brush, water jetting etc. then Pro.

& Fix. Chicken wire mesh of 16x24 guage Mesh to Prevent the

damaged part of the existing R.C.C. member through attend

ensure proper bonding between old and new concrete

application of bonding coat of slurry of POLYALK-EP and

cement in 1:2 (1 cement : 2 polyalk EP) after then Providing

mm thick cement plaster in single coat on single or half brick

walls for interior plastering upto floor two level and finished

even and smooth in (i) Cement mortar 1:3 (1-cement:3-sand)

including floating coat for finishing with a floating coat of neat

cement slurry.

[32] Providing and fixing Febric Curtain with Road & Eyelet with 226.00 Sqm 450.46

Scretch and Rust free 1" metal (iron) rod with decorative round

finials or either end. Powder coated finish in nickle, Bronze or

Black shades as sectrion to be supplied & installed in all

windoes with great precision. Febrick as per selction of

Architect, Stiching & fixing as required by desing allnecessary

fixtures & Fastners including finials, brackets, fishers etc.

[33] Providing and fixing wooden panneling made of framing the 87.00 Sqm 4044.46

skeleton (plywood frame structure) with 18mm + 18mm thick

MR grade plywood for vertical and horizontal plywood (patti)

one side cover with 6mm thick MR grade plywood for grooving

as per design.Fixing properly without any air gap and finishing

with seletced 1.00 mm thick laminate.Before installation, make

hole/face plate for conduit pipes of eletcrical/networking

cables with openable stud from partition Including all materials

and labour etc. complete as per detail drawing and instruction

of engineer-in charge.Wooden Pelmat Laminate

[34] Providing and erecting Approved make Ceiling fan with double 3.00 Ea. 1596.81

ball bearing ISI mark with condenser A.C. 23OV.50 c/s.1200

mm. sweep complete, canopy erected on existing hook or clamp

with earthing. [Make shall be approved by Engineer in charge]

[35] Replacing the bearing/ bushing of Ceiling fan and putting the 8.00 Ea. 103.02

fan in working order including credit of D.M. retained by

Agency. (a) Bearing

Description of Item

(with brief specification and reference to book of Quantity Unit Rate Amount

specifications)

[36] Providing following type of Modular Type Accessories mounted 14.00 Ea. 398.95

with PVC / metallic/Wooden box, single mounting base frame

covered with textured / metallic/white front plate, modules

erected with necessary connections as per site situation

directed by Engineer In charge. (5) Electronic hum Free steps

EME Fan regulator, Cat.III

[37] Replacing condenser for ceiling fan/ Exhaust Fan / Pedestal Fan 13.00 Ea. 64.64

/ Table Fan / Cabin Fan {Credit of D.M. retained by Agency.}

[38] Providing & erecting following type of Modular Type 55.00 Ea. 27.27

Accessories with necessary connection As desired by Engineer

In charge. (1) 6 Amp. SP one way switch

[39] Providing & erecting following type of Modular Type 40.00 Ea. 51.51

Accessories with necessary connection As desired by Engineer

In charge. (2) 16 Amp. SP one way switch

[40] Providing & erecting following type of Modular Type 23.00 Ea. 82.82

Accessories with necessary connection As desired by Engineer

In charge. (3) 6/16Amp. Universal socket

[41] Providing & erecting following type of Modular Type 23.00 Ea. 42.42

Accessories with necessary connection As desired by Engineer

In charge. (4) 6 A socket

[42] Providing & erecting Switch board for Computer or electric 3.00 Ea. 1133.22

apparatus consisting of following modular type accessories

mounted with PVC / Metallic concealed /open box with single

mounting base frame covered with textured / metallic /white

front plate, modules erected with necessary connections as

1 no. 6A/16A universal plug-switch combined.

3 nos. 6A Switch

3 nos. 6A 5 pin Plug,

For Modular Type Accessories, Cat.III

[43] Supplying and erecting LED indoor fittings with LEDs of 8.00 Ea. 295.93

wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB, with

housing used as a heat sink shall be made of thick sheet Steel

conforming to IS: 513/CRCA/ aluminium die cast powder

coated and high U.V. & corrosion resistance with diffuser with

company mark/name 160V to 270V, Power Factor more than

0.95, THD < 15%, CCT 3000 K to 6500K, Luminaire efficacy>

lumens/watt, LED driver efficiency > 85 % (fitting required LM-

79 & LM-80 Certificates) (NOTE: Below description have shown

ranges of Wattage capacity of LED fittings.The Engineer

shown.) (A) Tube Light with integral driver (iii) 18-20 Watts,

Surge - 2KV, IP-20, conventional 4 feet, Cat-III

[44] Demolition and disposal of unserviceable materials with all lead 543.90 Cum 593.35

and lift. (i) Cement concrete.

[45] Providing and applying two coats of Hybrid Polymer flexible 3640.00 Sqm 646.62

acrylic coating of Sovacryl K-10 of Parex (Sika India) or

approved equivalent brand with under coat adhesion promotor

priming coat of Flow Prime WB of Parex (Sika India) or

approved equivalent make.Cleaning the existing surface

throughly, chase open the crack available at surface and fill the

same with crack filler material of approved brand. After

application of 1st coat of Sovacryl K-10 on Flowprime WB, a

fibre glass mesh of 45 GSM to be sandwiched between 1st &

2nd coat of Sovacryl K-10. The products shall be applied in

strict accordance with the manufacturer's specification. (The

crack filling shall be paid under relevant item) .

Description of Item

(with brief specification and reference to book of Quantity Unit Rate Amount

specifications)

[46] Providing and laying concrete 1:2:4 (1 cement :2 coarse Sand: 4 409.40 Cum 4174.38

Graded Stone Aggregate 20 mm nominal size) in proper

gradient on terrace slab as directed by Engineer-in-charge to

have proper slope for draining rain water including finishing

top with floating coat of neat cement.

[47] Providing & fixing of Waste Pipe for Wash basin & Urinal C.P. 40 24.00 Each 80.71

mm dia. as per the instruction of Engineer-In-Charge.

[48] Providing and fixing glazed louvered glass windows and 4.20 Sq.m 4143.57

ventilators with teak wood frame 10cm. x 7cm. size including

coats of oil painting to wood work etc. complete.

[49] Scientific cleaning of over head water tank and under ground 126000.00 Litre 0.30

sump including wall cleaning with turbolesor with high

Pressure and removed sludge and impurties of suction

operation in under ground water sump wt. and dry cleaning by

vacuum pump disinfiucion with anti backterial agent and viral

disinfection with U.V. radiation and mosquitto distroy with

specific system etc. complete. (D) More Than 5000 litre

[50] Providing erecting and fixing double coated ISI water tank of 19000.00 Litre 3.95

required capacity each with all necessary fittings and

connection etc. complete on terrace

[51] Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 35.00 Rmt 125.67

working pressure poluthene pipes of the following outside Dia.

Low densidy, complete with special falnge compression type

fittings, wall clipsetc. including making good the wall ceiling

and floor. (D) 40mm

[52] Providing and fixing 12.5 Litres low level flushing cistern with a 10.00 Each 2344.42

pair, of C.I. or Mild brackets, complete with fittings such as lead

valve less syphon, 15mm nom.nal size brass ball valve with

polythene float, C.P brass handle unions and couplings for

connections, with inlet, outlet and overflow pipes, 40mm dia.

porcelain enamelled flush bend including cutting holes in walls

and making good the same connecting the flush bend with

cistern and closet (overflow pipe to be measured and paid for

separately) (A) Vitreous China (I) In white colour

[53] Providing and fixing Health Fauset Heavy duty with hook with 11.00 No 1003.14

fitting including all labour and materials as directed by engineer

in charge.

[54] Providing and fixing pillar tap, capstan head, screw down high 15.00 Each 354.69

pressure with screws, shanks and back nuts. (ii) 20mm dia.

[55] Providing and fixing flat back wash basin 550 mm x 400 mm 10.00 Each 1909.33

size of first grade, white in colour with single hole for pillar trap

with CI or MS brackets painted with including cutting holes and

making good the same including providing and fixing CP brass

wastecoupling 32mm dia including providing and fixing MI

washer union 32 mm dia, including providing and fixing 15mm

dia pillar tap capstan head screw down high pressure with

screws, shanks and back nuts, including providing and fixing

waste pipe 15mm x 600 mm pvc inlet connection 15mm brass

screw down stop tap with necessary fittings etc. complete

[56] Providing and fixing coloured wash down water closet 5.00 Each 1595.04

(European type WC pan) with integral 'P' or 'S' trap with soil

pipe in cement mortar 1:1 (1 cement : 1 fine sand) with

coloured plastic seat cover with CP brass hinges and rubber

buffers including cutting holes in wall and making good the

same etc complete.

Description of Item

(with brief specification and reference to book of Quantity Unit Rate Amount

specifications)

[57] Providing and laying Acrylic Polymer type waterproofing 70.00 Rmt 96.59

treatment to terrace by Cutting out cracks of roof terrace to V-

section, cleaning out, wetting, grouting with cement and sand

slurry 1:3 (1-cement 3-sand) including waterproofing Solutions

in single coat then applying second coat of waterproofing

materilas with white cement to seal the joints properly using

brush as directed by Engineer in charge..

[58] Lifting of submersible motor pump set complete with required 3.00 Per Job 1711.95

No .& size of casing pipes by means of proper chain pulley block

and pipe. wrenches. Job includes stacking of pipes

chronologically after due checking of threads. (A) Up to 60 mtrs.

[59] Replacement of bronze/ carbon thrust bearing with fibre plate 1.00 Ea. 2235.13

& housing for (B) 200 mm dia.

[60] Rewinding of submersible motor by using approved make PVC 1.00 Ea. 2559.34

insulated copper winding Cores of suitable size complete with

connection. Capacity Suitable for pump of following size.

Dismantled Materials to be retained by agency. (B) 7.5 H.P

[61] Replacement of motor bush, upper/ lower with sleeve with 2.00 Ea. 1096.86

following material (A) Bronze (ii) 200 mm. dia.

[62] Replacement of Bowl bearing/ bush (B) Lead (ii) 200 mm. dia. 1.00 Ea. 1182.71

[63] Providing Water proof straight Joint in PVC insulated flat 6.00 Ea. 189.88

flexible copper cable by using insulating material, water

proofing material, & making the joint complete. (A) Up to 10Sq.

[64] Providing and erecting ISI marked PVC insulated PVC Sheathed 34.00 Mtr 146.45

Flat flexible Submersible copper cable approved make of

following Size. (C) 3 Core x 4 Sq. mm

[65] Supply of following size of TOP & BOTTOM accessories i.e. 2.00 Per Set. 2681.55

Adaptor set (CI) long, pump guard set, starter pipe Rubber ring

for submersible pump & UPVC column pipe as directed by

Engineer - in - charge with necessary plumbing as desired. [F]

[66] Lowering of submersible motor pump set at the depth of 3.00 Per Job 1711.95

following, complete with required. Nos. and size of casing pipes

erected by means of proper chain pulley block & pipe wrenches

after checking of threads of each pipe with coupling to take the

load of the pump set and pipe assembly filled up with water (A)

Up to 60 mtrs.

[67] Dismantling tiled of Stone foor laid in mortar including stacking 775.00 Sq.m 46.77

of serviceble materilas and disposal of unservicebe materials

with all lead and lift.

[68] Dismentling C.I. pipes G.S. W.pipes and A.C. rain water pipes 602.00 Rmt 73.02

with fittings and clamps including stacking the materials with

all lead and lift (for any dia, of pipe)

Description of Item

(with brief specification and reference to book of Quantity Unit Rate Amount

specifications)

[69] CHIPPING EXIST CONC 788.00 Sq.m 355.42

Surface of member should be checked for sounding using

hammer. The damaged / delaminated portion will sound hollow

The same should be marked to regular geometrical shapes. The

edges should be grooved using slim and powerful 850W (230V)

corded angle grinder about 25 mm deep. Grinder to have no

load speed of 11500 rpm with on / off side switch and for use of

cutting disc upto 100 mm. Concrete within the grooved area

should be removed using High performance chipper hammer

featuring low weight & low vibration having single impact

energy of 7.5 J, full hammering frequency of

impacts/minute, maximum chiselling performance of

cm3/min, weighted emmission sound pressure level of 94 dB

(A) according to EN 60745, Triaxial vibration for chiseling in

concrete 12. Im/s2 according to 60745-2-6 and having weight

according to EPTA procedure 01/2003 of 5.6 Kgs

[70] P/A ANTI CORROSIVE 788.00 Sq.m 246.29

REINFORCEMENT: Providing and applying anti corrosive rust

remover "Rusticide" of M/S Sunanda speciality coating pvt. Ltd.

or equivalent approved including cleaning the reinforcement

bars with wire brush or air blowing including removing of all

loose particle with applying rust remover thoroughly on

reinforcement bars by using cotton waste swab etc. comp. with

all the required tools, tackles, labourers as required and as

directed by the Engineer in charge. (Area of Concrete treated

with poymer modified mortar shall be measured for payment

[71] P/A STEEL PROTECTIVE COATING: 788.00 Sq.m 346.90

Providing and Applying Steel protective coating: The exposed

and cleaned reinforcement bars shall be applied with a single

component cementitious corrosion inhibiting primer which

shall be applied on the surface using suitable brush. Product:

Mucis Protozione Ferro Mono of Thermax (Area of Concrete

treated with poymer modified mortar shall be measured for

payment please)

[72] Bonding Coat 788.00 Sqmt 324.04

Providing and applying bond coat on the prepared surface to

receive new polymer mortar / polymer modified concrete, with

application of bonding coat of slurry made of Polyalk EP of M /S

Sunanda Speciallty Coating Private Ltd or of equivalent

approved brand and manufacture in the weight proportion of

:2 (1 cement 2 Polyalk EP) or / Lanco 751 of Parex Chemicals or

Krishna Conchem as per manufactures specification over the

cleaned and dried old concrete surface in one full coat Laying of

reinforcement polymer mortar or micro concrete shall b

completed within the overlay time of bonding coat This coat s

bonding agent between old and new concrete and also acts as

'barrier coat' to the migration of chloride ions from host

concrete Item rate is inclusive of the materials all labour,

scaffoling, supervision, tools and tackles and transportation etc

complete a per specification and as directe To ensure proper

bonding between old and new concre application of bonding

coat of slurry made of Polyalk EP of M /S Sunanda Speciallty

Coating Private Ltd or of equivalent approved brand and

manufacture in the weight proportion of 1 :2 (1 Cement :

Polyalk EP) or Lanco 751 of Parex Chemical as per

manufactures specification over the cleaned and dried old

concrete surface

Description of Item

(with brief specification and reference to book of Quantity Unit Rate Amount

specifications)

[73] P&A POLYMER MODIFIED CEMENT MORTAR Applying 788.00 Sqmt 1939.94

Corrosion Resistance single Component polymer modified

cement mortar to patch up the damaged concrete section in

planks of upto 25mm thickness Providing and a g and applying

Corrosion Resistance Single Component, polymer modified,

fiber reinforced ementatious repair mortar having water

powder ratio in the range of 0.16 and the mixed density of

around 2.05 - 2.20 Gms/cc. The repair mortar shall achieve a

minimum compressive strength of 45 MPa @ 28 days when

tested as per ASTM C -109 and a flexural strength of 7 MPa

when tested as per ASTM C 348. It shall achieve a minimum

Adhesion Bond Strength of 2 MPa when tested on Standard

Elcometer as per ASTM D 4541 - 8 The modulus of Elasticity

shall be a minimum of 28 kN/mm2 when tested as per BS

Product: corrosion esistance single Component, polymer

modified, fibre reinforced cementitious of M/s. Fosroc

(Renderoc SP-40) , Parex (Lanko-731) .

[74] Providing and applying 15 mm thick mala plaster in single coat 945.00 Sqmt 242.28

on ir side on brick / concrete wall for interior plastering in C.M.

1:3 cement: 3 coarse sand) incl. finishing with a floating coat of

neat cement slurry

[75] Distempering (Three coats) with oil bound washable distemper 2364.00 Sqmt 112.49

of approved brand and manufacture and of required shade on

wall surfaces to give and even shade over and including a

primer coat with alkali resistance primer of approved brand

after thoroughly brushing the surface to give an even shade free

from mortar droppings and other foreign matter and also

including preparing the surface even and smooth for all floor

etc. complete.

[76] Providing laying and jointing in true line and level 15mm dia 125.00 Rmt 72.65

U.P. V.C. Pipe (SCH- 40) for cold water including fittings make or

equivalent as approved by Engineer In Charge. Pipe shall be

fixed on the help of clamp at every two meter C / C or shall be

Concelled as directed in including necessary Fitting etc.

including testing of pipe and joints and fixing the same with

adhesiv solvent, including cost of all materials

[77] Providing laying and jointing in true line and level 25mm dia 264.00 Rmt 91.84

U.P. V.C. Pipe (SCH- 40) for cold water including fittings make or

equivalent as approved by Engineer In Charge. Pipe shall be

fixed on the help of clamp at every two meter C / C or shall be

Concelled as directed in including necessary Fitting etc.

including testing of pipe and joints and fixing the same with

adhesiv solvent, including cost of all materials

[78] Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 197.00 Rmt 277.43

working pressure polythene pipes of the following outside Dia.

Low densidy, complete with special

falnge compression type fittings, wall clipsetc. including making

good the wall ceiling and

floor. (F) 75mm

Description of Item

(with brief specification and reference to book of Quantity Unit Rate Amount

specifications)

[79] Providing, laying and jointing in true line and level 110 175.00 Rmt 835.15

diametre U.P.V.C (Type B) conforming to IS 13592-1992 with

one end plain and other end socketed with rubber ring, &

fittings conforming to ISI 14735-1999 of approved make for

drainage system pipe line, pipe shall be jointed with each other

with rubber lubricant, pipe shall be fixed on wall using of PVC

clamp of the size 110 mm diametre x 149 mm length x 145 mm

heigh at every 2000 mm center to center or shall be concealed

in walls as directed including necessary fittings such as bends,

shoes etc. including testing of pipes and joints and jointed with

adhesive solvent cement including cost of all materials.

[80] Providing and laying Ceramic tiles 6mm thick in flooring treads 147.00 Sqm 949.68

of steps and landing laid on a bed of 12mm thick cement mortar

1:3 (1-cement : 3-coarse sand) finishing with flush pointing in

white cement. (up to 10 ton)

[81] Providing and laying coloured glazed tiles of the size 300 mm x 456.00 Sqm 1417.36

200 mm x 8 mm / 300 mm x 450 mm x 8 mm in skirting, risers

of steps and dedo on 10 mm. thick cement plaster 1:3 (1 cement

: 3 coarse sand) & jointed with white cement slurry.

[82] Providing and fixing machine Cut, Free edge. machin polishec 19.10 Sqm 3579.67

Granite stone slab 18 mm thick (single piece not more than

Doors/Windows sill and Jambs, staircase tread and risers

cladding etc. as per design including edge polish of a edges of

granite stone and laid on 20 mm thick cement mortar 1:6 (1

cement:6 coarse sand) jointed with grey cement slurrly

including rubbing and polishing finishing etc Complete.

[83] Removing and scraping of old deteriorated plaster of any 210.00 Sqm 18.94

thickness fromm wall / R.C.C member including stacking of

serviceable material and disposal of unserviceable from site of

work with all lead and lift.

[84] Dismentling doors, windows, ventilators etc. (wood or steel) 6.00 Each 244.98

shutters including chowkhats architraves, holdfasts and other

attachment etc. complete and stacking them within all lead and

lift. (ii) Exceeding 3 Sq.M. in area.

[85] Brick work using common burnt clay building bricks having 4.00 Cum 4021.02

crushing strength not less than 35 Kg./Sq.m. in foundation and

plinth in cement mortar 1:6 (1 cement:6 fine sand) (b)

Conventional.

[86] Providing 15mm thick cement plaster in single coat on Rough 34.00 Sqm 217.46

(Similar) side of single or half brick walls for interior plastering

upto floor two level and finished even and smooth in (i) Cement

mortar 1:3 (1-cement:3-sand)

[87] Providing and laying Mirror polished Machine polished Granite 10.50 Sqm 2629.03

stone slab 18mm (Average) thick for doors & windows sill &

Jams clading as per design including full moulded round front

steps & 1cm nosing & necessary groove on trads of steps ;laid

on 20mm thick cement mortar 1:6 (1 cement : 6 coarse sand)

jointed with gray cement sluury including rubbing and

polsihing etc. complete.for Doors / windows sill & jams clading.

[88] Wall painting with Applying two coats of putty & two coats of 4822.00 Sqm 160.01

primer of approved brand (three coats) plastic emulsion paint

with one wall in every to highlight in special effect (royal play)

color shade and color of approved brand and manufacture on

undecorated wall surface to give an even shade including

throughly brushing the surface free from mortar droppings and

other foreign matter and sand papered smooth.

Description of Item

(with brief specification and reference to book of Quantity Unit Rate Amount

specifications)

[89] Providing and laying Vitrified tiles 8 to 10 mm thick, 24'' x 24'' 139.00 Sqm 1484.61

in flooring treads of steps and landing laid on a bed of 12mm

thick cement mortar 1:3 (1-cement :3-coarse sand) finishing

with flush pointing in white cement.

[90] Applying general insecticide pest control treatment to floors, 324.00 Sqm 89.28

cupboards etc including labour materials etc. complete. Using

Imidacloprid 30.5 SCas Per IS 6313 part -II ( (0.075%

concentration by mass) is recommended 10.5ml chemical

diluted with 5 liters of water application 0.5 litre chemical

/Sqm of surface is recommended as per I.S.

[91] Finishing wall with Texture Finish paint of metallic finish on 23.00 Sqm 1415.34

wall surface (three coat) including priming coat to give and

even shade / pattern and of approved brand and manufacture

including all material and labour work with thoroughly

brooming the surface to remove all dirt and remains of loose

powered material etc. complete.

[92] Providing and fixing wooden panneling made of framing the 56.00 Sqm 5404.62

skeleton (plywood frame structure) with 18mm + 18mm thick

MR grade plywood for vertical and horizontal plywood (patti)

one side cover with 6mm thick MR grade plywood for grooving

as per design.Fixing properly without any air gap and finishing

with seletced 1.00 mm thick laminate.Before installation, make

hole/face plate for conduit pipes of eletcrical/networking

cables with openable stud from partition Including all materials

and labour etc. complete as per detail drawing and instruction

of engineer-in charge.Wooden Pelmat Veneer

[93] WOODEN PARTITION 63.00 Sqm 3610.75

Providing and fixing partitions, the average height of partition

will be 1520 mm. The basic structure shall be made out of the

Alluminium tubular/rolled section as framing, Aluminium Box

Section size of 50mm x 25mm x 1.6mm thickness & at

suggested intervals i.e 600 c / c fixed with each other

50MM*25MM*1MM thickness angle cleat proper fixity. The

entire Alu. frame work shall be covered with 8 mm thickness

plywood IS 310 on both the sides. All open sides of the

framework shall be covered with the 12 mm thickness plywood

for partitions. All the gaps either vertical or horizontal with

proper material shall be filled properly. All the vertical

members of the partition shall be inserted / fixed in the floor for

proper strength necessary provisions shall be made in the

partition for the electrical conduits / switch boards/etc. The

external plywood components including the thcikness of

partition shall be finished with 1 MM thickness decorative

laminate on both the sides. All visible exposed area of the

partition covered with Indian teak wood beading where ever

required. It shall have (3 coats) malamine sprey polishing

finish. The quoting price should be inclusive of all types of taxes

& duties, packing, forwarding, loading, unloading, installaion. As

per detail drawing & choice of users department and Concern

officers in charge as directed by the Architect / Engineer.

[94] Repairing to Door / Window including dissembling from frame, 51.00 Sqm 579.12

wroughting, providing patti, angles, replacing / repairing

stoppers - aldrops - handles etc. for proper fixing in to frame

hole etc. complete for smooth operation and proper utilization

including assambeling and refixing of the same as directed by

Engineer-in-charge.

Description of Item

(with brief specification and reference to book of Quantity Unit Rate Amount

specifications)

[95] Both side laminate finish flush door.Providing Material & 8.00 Sqm 4057.17

Labour charge for making laminate finish Flush Door (finished

size of door is 40 mm) of size 975 mm x 2400 mm considering

waterproof flush door sheet of 38 mm thkness covered both

side by 1.0 mm thick Laminate supprted by SS -314 finish

hinges. All exposed framing of 65 mm x12 mm made by teak

wood bidding complete with polish. Finishing with all necessary

hardwares like handles, conceal mortise locks, cylinders with

nos of keys, stopers, tower bolt, MS nails, SS-314 screws etc. as

per details given in drawing and as per instructions of

Architect/Engineer In charge. Please see the Attached Make List

for Apporoved Makes.

[96] Providing and supplying Medium back chair for conference with 5.00 No 15219.83

M.S frame work. Upholstered with changeable fabric upholstery

covers (as per requirement) and molded PU foam, together with

molded seat & back covers. The back foam should be designed

with contoured lumber support for extra comfort. Caster of high

durability & hydraulic. The chair should have cylinder with

years warranty. The size of chair 47.5cm x 58cm (Back side)

and 49cm x 48cm (seat size) . The PU foam should be molded

with density =45 ± 2 kg/m3 .with One piece armrests. The

armrests are scratch and weather resistant. The permanent

contact mechanisms is designed with 360° revolving type, with

pneumatic height adjustment & 17 ° maximum tilt only & tilt

tension adjustment facility. complete as per sample approved

and as directed by the Architect and approved by the Engineer

[97] Providing And Arranging table for chamber having overall 5.00 No 46293.25

thickness of Top 40 mm (18+18+4mm) 18 mm thick MR Grade

plywood and 4.00 mm thick veneer at top with melamine polish

finish including 8mm thick back painted glass. Top to be made

from 75mm x 50 mm Indian teak wood with half round

moulded on long side with melamine polish. Leg 50 mm x

mm x 1.6 mm thick CRCA Square pipe and supporting pipe

mm x 25mm x 1.8 mm finishing with epoxy powder coated

micron with leveller. Appron having 18 mm thick MR Grade

plywood with 4.00 mm thick veneer having melamine polish

finish. Drawer Unit-450 x 550 x 600 mm having all Structure

mm thick MR grade plywood with veneer and teakwood border

of specified size with melamine polish finish. Drawers (3 Nos)

slides on Ebco make telescopic channel with Godrej make lock

with two keys and necessary fixtures and fastening as approved

with balancing laminate inside 0.8 mm thick of approved shade

including all materials and labour etc. Complete as per drawing

and instruction of engineer-in charge. Side Unit to be provided

saparetly.Judge Table with MDU veneer Size :- 1800mm x

[98] Providing and supply The chair pipe structure of MS CRCA 6.00 No 4533.57

finish 16 gauge round pipe having a diameter of 32 mm, the

understructure frame tubular structure with stability for proper

balance, the seat and back is supported on spring structure, the

backrest armrest and seat dimensioned and curved from an

ergonomics point of view, the frame and spring-seat structure

prepared from MIG welding process & powder coated, proper

high-density rubber bush provided at all four legs, seat & back

upholstered with fabric.

Description of Item

(with brief specification and reference to book of Quantity Unit Rate Amount

specifications)

[99] Zebra Roller blinds-CURTAIN :- Blinds assemblies are to be 49.00 Sqm 2147.26

supplied & installed in all windows with great precision. It

should be water resitant and fitted on alluminium headrails

duly power coated and fitted with stainless steel drive rods.

Manual operated and should have ISI mark.Providing & fixing

roller type window curtains of Deck, Aerolux, Siddhi or eq.

make including same brand channel - chain mechanism,

synthetic black out fabric of approved colour & design, silver

coated backside, same fabric plated pelmet etc. with all

necessary fittings etc. complete as per Architect/ Site engineer's

instructions as per sized specified in detail drawings.Material

architect.

[100] CHIPPING EXIST CONC.FROM RCC MEMBER 16.00 Sqm 192.91

Surface of member should be checked for sounding using

hammer. The damaged/ delaminated portion will sound hollow.

The same should be marked to regular geometrical shapes. The

edges should be grooved using slim and powerful 850W (230V)

corded angle grinder about 25 mm deep. Grinder to have no

load speed of 11500 rpm with on / off side switch and for use of

cutting disc upto 100 mm. Concrete within the grooved area

should be removed using High performance chipper hammer

featuring low weight & low vibration having single impact

energy of 7.5 J, full hammering frequency of

impacts/minute, maximum chiselling performance of

cm3/min, weighted emmission sound pressure level of 94 dB

(A) according to EN 60745, Triaxial vibration for chiseling in

concrete 12.1m/s2 according to 60745-2-6 and having weight

according to EPTA procedure 01/2003 of 5.6 Kgs

[101] P/A ANTI CORROSIVE RUST REMOVER ON REINFORCEMENT : 226.00 Sqm 236.34

Providing and applying anti corrosive rust remover "Rusticide"

of M/S Sunanda speciality coating pvt Ltd or equivalent

approved including cleaning the reinforcement bars with wire

brush or air blowing including removing of all loose particle

with applying rust remover thoroughly on reinforcement bars

by using cotton waste swab etc. comp. with all the required

tools, tackles, labourers as required and as directed by the

Engineer in charge. (Area of Concrete treated with poymer

modified mortar shall be measured for payment please)

[102] P/A STEEL PROTECTIVE COATING : 226.00 Sqm 318.15

Providing and Applying Steel protective coating: The exposed

and cleaned reinforcement bars shall be applied with a single

component cementitious corrosion inhibiting primer which

shall be applied on the surface using suitable brush. Product:

Mucis Protozione Ferro Mono of Thermax (Area of Concrete

treated with poymer modified mortar shall be measured for

payment please)

Description of Item

(with brief specification and reference to book of Quantity Unit Rate Amount

specifications)

[103] P&A POLYMER MODIFIED CEMENT MORTAR : 226.00 Sqm 1591.76

Applying Corrosion Resistance single Component, polymer

modified cement mortar to patch up the damaged concrete

section in planks of upto 25mm thickness. Providing and

applying Corrosion Resistance Single Component, polymer

modified, fiber reinforced ementatious repair mortar having

water powder ratio in the range of 0.16 and the mixed density

of around 2.05 - 2.20 Gms/cc. The repair mortar shall achieve a

minimum compressive strength of 45 MPa @ 28 days when

tested as per ASTM C-109 and a flexural strength of 7 MPa when

tested as per ASTM C 348. It shall achieve a minimum Adhesion

Bond Strength of 2 MPa when tested on Standard Elcometer as

per ASTM D 4541 - 85. The modulus of Elasticity shall be a

minimum of 28 kN/mm2 when tested as per BS 1881. Product:

corrosion esistance single Component, polymer modified, fibre

reinforced cementitious of M/s. Fosroc (Renderoc SP-40)

Parex (Lanko-731) .

[104] Pro. And fixing false ceiling using Water proof Wooden Plywood 43.50 Sqm 1696.80

Plank 9 mm Thick sections using water proof board of size

mm x 1830 mm x 8.0 mm suspended by GI suspender channel

of size 25 mm x 3 mm with intermediate channel og size 18 mm

x 40 mm x 0.8 mm at 1220 mm center to center ceiling section

of size 40 mm x 35 mm x 0.55 mm at 457 mm c/c and perimeter

channel A of size 20 mm x 27 mm x 30 mm x 0.5 mm at edges &

drops incl.paper tap sand sofit cleat, anchor fastener, scoch bolt

connecting cleat, joining compound top coat on ceiling

incl.making necy.opening for light fitting, diffuser etc. comp. as

per detail drawing as directed Engineer in Charge.

[105] Providing and supplying Main Table including table unite, side 3.60 Sqm 18141.04

unite made with 19mm Thk. Plywood structure with 6mm thick

venier finished corian sheet (including buffing and fabrication

cost) for Top desk and as per architect drawing finished with

1.0 mm Thk. decorative laminate on outside portion &0.8 mm

Thk. liner Laminate inside as specified & approved by architect

fixed with necessary fixtures and fastening (Hardware) as per

architect drawing. Provide Plastic Computer Table Grommet

Cable Wire Outlet Hole Cover 60mm, Key-board trey, S.S legs,

Drawers with telescopic roller channels, Handle and locking

arrangements with all necessary fixtures and fastening .Provide

Shutters as per drawing fixed with handle, hinges, magnet,

complete with bidding patties and all required hardware

.Provide footrest as per drawing. All exposed edges shall be

covered with required Teak wood beading Patti finished with

approved melamine polishing work. Complete as per architect's

drawing and as per instruction of architect & engineer in

charge. (Refer drawing)

[106] Providing and fixing aluminium partition comprising anodized / 41.50 Sqm 3232.00

powder-coated aluminium sections of approved make and

profile, including necessary vertical and horizontal members,

cleats, brackets, screws, anchors, and all required accessories,

complete as directed by the Engineer-in-Charge. The partition

shall be constructed with lower solid panel portion and upper

glazed portion (half glass) , using 5–6 mm thick clear / frosted

glass fixed with approved beading and rubber gasket, including

cutting, edge polishing, and proper placement. The solid portion

shall be made from approved board / sheet (as specified)

securely fixed within aluminium framing. The work includes all

labour, materials, T&P, carriage, cutting, fitting, assembling,

sealing, and finishing complete in all respects as per site

requirements and instructions of the Engineer-in-Charge

Description of Item

(with brief specification and reference to book of Quantity Unit Rate Amount

specifications)

[107] Providing and supplying a full-height storage unit measuring 1.00 NOS 33218.90

2.0m (W) x 0.60m (D) x 2.10m (H) , constructed with 19mm

thick plywood structure. The exterior is finished with4mm thick

Veneer with melamine polish and 0.8mm thick balancing

laminate, and the interior is lined with 0.8mm thick liner

laminate, as per the specifications approved by the architect.

The shutters are equipped with required handles, hinges,

magnets, and locks. Removable plywood shelves are supported

on side teakwood battens on both sides for adjustability. All

exposed edges are covered with 8mm thick teakwood beading,

finished with melamine polish. The unit includes all necessary

hardware, fixtures, and fastenings, and the work is to be

completed as per architect drawings and the instructions of the

architect and Engineer-in-Charge.

[108] Providing and laying 60 x 60cm Antiskid Vitrified tiles 8 to 10 3.50 Sqm 1073.13

mm thick in flooring treads of steps and landing laid on a bed of

12mm thick cement mortar 1:3 (1-cement : 3-coarse sand)

finishing with flush pointing in white cement.

[109] Providing and laying 60 x 60cm GTV Vitrified tiles 8 to 10 mm 6.50 Sqm 1141.45

thick with pattern colour & Shade as detailed approve by

architect (10% Dark colour tiles Pattern) in skrting risers of

steps and dedo on 10mm thick cement plaster 1:3 (1-cement : 3-

coarse sand) and jointed with white cement slurry

[110] Providing & laying cement concrete 1: 4 : 8 (1 Cement : 4 Coarse 5.50 Cum 3676.04

sand : 8 graded B.T stone aggregate 20mm nominal size) Curing

comp. including cost of form work in foundation and plinth

[111] Providing and fixing Handle valve of aprroved brand (B) 25mm 1.00 Nos 383.80

[112] Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 23.00 Nos 558.36

100 mm diameter with jali of the following nominal diameter of

self cleansing design with C.I scread down or hinged grating

including the cost of cutting and making good the walls.

[113] Providing & Fixing Premium quality approved make like Jaquar 1.00 Nos 18390.84

/ ESSCO or equivalent Wall Hung European type W C Pan with

in Built Jet, PP Soft closed seat cover, Hinges, Dual Flush cistern,

fixing accessary etc. complete of size 365 x 525 x 400 mm or

375 x 520 x 400 mm including cutting cutting holes and making

goods the same including labour, material, trasportation etc.

complete as directed by engineer incharge.

[114] Providing & Fixing Premium quality approved make like Jaquar 1.00 Nos 13286.60

/ ESSCO or equivalent Table top wash basin of 565 x 425 x

mm with hole for pillar tap with C.I or M.S brackets painted

white including cutting cutting holes and making goods the

same include. C.P. brass waste and waste pipes.including

labour, material, trasportation etc. complete as directed by

engineer incharge.

[115] Providing & Fixing Premium quality approved make like Jaquar 1.00 Nos 5976.05

/ ESSCO or equivalent Urinal of size 355 x 340 x 535 mm

connetcting with PVC waste pipe, Trap etc complete including

labour, material, trasportation etc. complete as directed by

engineer incharge.

[116] Providing & Fixing Premium quality approved make like Jaquar 1.00 Nos 3185.67

/ ESSCO or equivalent Bib cock with wall flange including

labour, material, trasportation etc. complete as directed by

engineer incharge.

[117] Providing and fixing toilet paper holder. (A) C.P. Brass 4.00 Nos 418.68

Description of Item

(with brief specification and reference to book of Quantity Unit Rate Amount

specifications)

[118] Providing and fixing 600mm x 450mm bevelled edge mirrror of 20.00 Nos 833.73

superior glass mounted on 6mm thick A.C. sheet or plywood

sheet and fixing to wooden pluge with C.P. brass screws and

[119] Providing and fixing C.P. brass towel rail comlete with C.P. brass 15.00 Nos 603.19

brackets fixed to wooden plugs with C.P. brass scews. (B)

600mm x 20mm size

[120] Providing and fixing S.W. gully trap with C.I. grating brick 4.00 Nos 1246.92

masonry chamber and water tight C.I. cover with frame of

300mm x 300mm size (inside) with standard weight. (i) Square

mouth traps. (B) 150mm x 100mm size P of R type

[121] Providing & Fixing Premium quality approved make like Jaquar 2.00 Nos 2365.05

/ ESSCO or equivalent Angular stop cock with wall flange

including labour, material, trasportation etc. complete as

directed by engineer incharge.

[122] Providing and fixing window having extruded aluminum Colour 5.50 Sqm 1705.67

Powder Coated section frame main outer size 63.50 x 38.10 x

1.95 mm, @ Wt 1.094 Kg / Rmt, horizontal two track member

size 61.85 mm x 31.75 mm x 1.20mm @ wt.of 0.695 Kg/mt,

vertical member of size 61.85 mm x 31.75mm x 1.30 mm @

wt.of 0.0.659 Kg/mt with sliding shutters of horizontal member

size 40mm x 18mm x 1.29mm @ wt.of 0.456Kg/mt, vertical

member of size 40mm x 18mm x 1.29mm @ wt.of 0.456Kg/mt

with 5 mm thick transparent bronze colour tinted float glass

with powder coated aluminum fittings and fixtures and

transparent silicon sealant glass fixing to frame as per details

etc complete for window

[123] Dismentling doors, windows, ventilators etc. (wood or steel) 31.00 Each 182.94

shutters including chowkhats architraves, holdfasts and other

attachment etc. complete and stacking them within all lead and

lift. (i) Not exceeding 3 Sq.M. in area

[124] Providing 15mm thick mala plaster in single coat on fair on 290.00 Sqm 242.28

brick / concrete wall for interior plastering in C.M.1:3 (1

Cement : 3 Coars sand) incl. finishing with a floating coat on

neat cement slurry

[125] Removing and scraping of old deteriorated plaster of any 288.00 Sq.m 18.94

thickness fromm wall / R.C.C member including stacking of

serviceable material and disposal of unserviceable from site of

work with all lead and lift

[126] Repairing to Door / Window including dissembling from frame, 15.00 Sq.m 567.79

wroughting, providing patti, angles, replacing / repairing

stoppers - aldrops - handles etc. for proper fixing in to frame

hole etc. complete for smooth operation and proper utilization

including assambeling and Refixing of the same and Painting

one coats (excluding priming coat) on previously painted wood

and wood based surface with enamel paint, to give an even

shade including cleaning the of all dirt, dust and other foreign

matter. as directed by Engineer-in-charge.

[127] Providing and laying Synroof High bond ecentromentric 1010.00 Sq.m 569.64

premium quality acrylic coating as a water proofing membrance

finished which consists of a coat of bitumine primer & 80 CSM

membrance in sunk slab, Terrace Slab with ulraviolet resistance

and working upto any height etc. complete as directed by

Engineer in charge

[128] Providing and fixing washbasin with single hole for pillar tap 5.00 Each 1453.95

with C.I. or M.S. brackets painted white including sutting holes

and making good the same but excluding fittings. (A) Vitreous

China: (ii) Flat Back washbasin 550 mm x 400mm size. (i) In

white colour.

[129] Providing and fixing pillar tap, capstan head, screw down high 40.00 Each 308.73

pressure with screws, shanks and back nuts. (i) 15mm dia.

Description of Item

(with brief specification and reference to book of Quantity Unit Rate Amount

specifications)

[130] Providing and laying Vitrified tiles 8 to 10 mm thick, 24'' x 24'' 100.00 Sq.m 1073.13

in flooring treads of steps and landing laid on a bed of 12mm

thick cement mortar 1:3 (1-cement : 3-coarse sand) finishing

with flush pointing in white cement.

[131] Providing and fixing Fly proof galvanised S.S. wire gauge of I.S.I. 70.00 Sq.m 885.64

gauge designation 85 G. with wire of dia. 0.56 mm to windows

and celevating windows including 60 x 20 mm beading of teak

[132] Provoding and fixing flush door shutters, solid core 26.00 Sq.m 1797.77

construction with frame of first class hardwood with cross

board and face veneer or plywood face panels, including

anodised alluminium butt hinges with necessary screws. (B)

Non-decorative type and block board core anodised alluminium

butt hinges in flush door shutters (2) 35 mm thick.

[133] Providing and fixing 35 mm thick shutters for Doors, windows 11.00 Sq.m 3592.72

and clear story windows including anodised alluminium butt

hinges with necessary screws. (A) Indian Teak Wood (iii) Partly

panelledand partly glazed.

[134] Providing and fixing Urinal or approved quality including 5.00 Each 1036.27

conecting the Urinal with waste pipe, tap etc. complete. (A)

White earthenware flat back or corner type size 430mm x

[135] Scraping oil paint from steel and other metal surface and 33.00 Sqm 49.32

making the surface even (with Hand Scraping.)

[136] Painting two coat (excluding priming coat) on previously 33.00 Sqm 109.74

painted steel and other metal surface with enamel paint,

brushing to give an even shade including cleaning the surface of

all dirt, dust and other foreign matter.

[137] Providing and fixing water closet squatting Pan (Indian type 21.00 Each 933.78

W.C. Pan) size 580mm (Earthwork, bed concrete, foot reste and

trap to be measured and paid for separately) (A) Vitreous China.

(I) Long pattern = White

[138] ONE SIDE LAMINATE ONE SIDE VINEER FINISH FLUSH DOOR . 11.40 Sqm 7942.64

:- Providing Material & Labour charge for making Flush Door

(finished size of door is 46 mm) of size 975 mm x 2400 mm

considering waterproof flush door sheet of 38 mm thkness

covered outer side by 1.00 mm Laminate & Inside finished with

4 mm thk vineer finished with PU polish on single sides of

shutter & 1.0 mm thk laminate at other side of shutter supprted

by SS -316 finish hinges. All exposed framing of 62 mm x12 mm

made by teak wood bidding complete with polish. Finishing

with all necessary hardwares like handles, conceal mortise

locks, cylinders with 6 nos of keys, stopers, tower bolt, MS nails,

SS-304 screws etc. as per details given in drawing and as per

instructions of Architect/Engineer In charge. Please see the

Attached Make List for Apporoved Makes.

[139] Wall painting (Two coats) with plastic emulsion paint of 911.00 Sqm 78.90

approved brand and manufacture on undecorated wall surface

to give an even shade including throughly brushing the surface

free from mortar droppings and other foreign matter and sand

papered smooth.

[140] Providing and fixing powder coated aluminum standard 4.70 Sqm 3591.98

extruded section glazed type Door of 63.50 mm x 38.10 mm x

1.95 mm or as specified drawing or as directed having Top &

bottom panel of 5 mm thick coloured float glass at top including

all fixtures and fastenings like glazing clips, rubber gasket,

hardware like handel, tower bolt, 6 liver mortise lock etc. and

labour etc. complete as directed by engineer in charge.

Description of Item

(with brief specification and reference to book of Quantity Unit Rate Amount

specifications)

[141] Providing and fixing M.S. grills of required pattern to wooden 1141.00 Kg 106.09

frames of windows etc. with M.S. flats at required spacings and

frame alround, square or round bars with round headed bolts

and nuts or by screws (A) Plain Grill including Primer Coat and

two coats of oil paint as directed by engineer in charge.

[142] P & L 24" x 24" vitrified 8 mm thick tile flooring over 20 mm 478.20 Sqm 1397.83

(average) base of cement mortar 1:6 (1 cement: 6 coarse sand)

on new surface or fixing on existing flooring by adhesive

material including dismentaling of existing flooring and jointed

with color cement slurry including finised with flush pointing &

cleaning the surface etc. complete for antiskit

[143] Providing and laying Vitrified tiles 8 to 10 mm thick in skrting 127.00 Sqm 1538.85

risers of steps and dedo on 10 mm thick cement plaster 1:3 (1-

cement : 3-coarse sand) and jointed with white cement slurry.

[144] Providing and laying Polished Granite stone slab 18 mm 99.60 Sqm 1698.61

(Average) thick for Doors / WIndows Sill & Jambs Cladding as

per design incl. full moulded round front edge in trade of steps

laid on 20 mm thick cement mortar 1:6 (1 -cement : 6 coarse

sand) jointed with grey cement slurry including rubbing and

polishing etc. complete for Doors / WIndows Sill & Jambs

[145] Providing and fixing PREMIUM QUALITYL HUNG EWC: (WITH 3.00 No. 8727.86

CROFT SOFT CLOSE SEAT COVER) SNOW WHITE COLOUR-535

X 360 X 335 MM with integral "P" and "S" trap including jointing

the tra best quality brand including providing and fixing plastic

seat cover for wash down WC with CP brass hinges and rubber

buffers back plastic seat and including providing 12.50 Litres

low level flushing cisten with a "P" air of CI or MS bracket with

complete fitting such as lead valve Sipron 15mm dia brass ball

valve with polythene float CP brass handle, unions and

couplings for connection with inlet outlet and overflow pipes

40mm dia porcelain enamelled flush bend, including jet spray

operated with necessary valve of best quality brand including

cutting holes in walls and making good the same connecting the

flush bend with cistern and closet vitreous china etc. complete.

[146] Providing and fixing PREMIUM QUALITY COUNTER WASH 3.00 No. 4030.35

BASIN - CLIFF SNOW WHITE COLOUR-550 X 460 X 185 MM

with single hole for pillar tap with C.I. or M.S. brackets painted

white including sutting holes and making good the same with

brass union and CP brass wall discharge pipe with flanges and

cap of best quality brand, Waste Pipe for Wash basin C.P. 32 mm

dia with fittings up to floor trap, 32mm dia CP brass waste

coupline with CP chain and rubber plug, washer and CP brass

cap complete in all respects including cutting and making good

the walls RCC work as directed and making good the same etc.

[147] Providing and fixing Urinal of approved quality including 6.00 No. 1541.44

connection with trap and with integral longitudinal flush pipe.

(A) Squating plate pattern white earthenware 550mm x

[148] Providing and fixing screw down bib taps of following size. (B) 74.00 No. 186.83

Brass chromium plated screws down Bib Tap. (i) 15mm dia.

[149] Providing and fixing brass screw down stop tap. (A) 15mm dia. 40.00 No. 205.83

[150] Providing and fixing chromium plated brass half trun flush cock 17.00 No. 263.77

of approved quality including fixing in pipe line etc. complete.

(ii) 25mm dia.

Description of Item

(with brief specification and reference to book of Quantity Unit Rate Amount

specifications)

[151] Providing & Fixing Premium quality approved make like Jaquar 18.00 No. 1144.80

/ ESSCO or equivalent Health Fauset Heavy duty with hook with

fitting including labour, material, trasportation etc. complete as

directed by engineer incharge.

[152] Providing and fixing 600mm x 120mm glass shelf with C.P. 14.00 Each 515.40

brass bracket and guard rail complete mixed to wooden plug

with C.P. brass screws.

[153] Providing and fixing standared extruded of alluminium section 10.90 Sqm 1175.56

of size 63mm x 38.10mm x 1.2mm, @ Wt. 0.643 Kg/mt with

colour Powder Coated alluminium frame for ventilation with

mm thick frosted glass as details etc complete for Ventilation.

[154] Providing and fixing Fly proof S. S. wire gauge of I.S.l gauge 5.50 Sqm 1214.31

designation 85 G. with wire of dia.0.56 mm to windows and

celevating windows including Anodized Alluminum Section

with allu. power coated fittings and fixture etc complete.

[155] Providing and fixing S.W. gully trap with C.I. grating brick 6.00 No. 1292.19

masonry chamber and water tight C.I. cover with frame of

300mm x 300mm size (inside) with standard weight. (i) Square

mouth traps. (A) 100mm x 100mm size P type.

[156] Constructing brick masonry chamber for underground C.I. 6.00 No. 2932.93

Inspection chamber and bends with bricks having crushing

strength not less than 35Kg/Cm2 in C.M. 1:5 C.I. cover with

frame (Light duty) 455mm x 610mm intenal dimensions total

weight of cover with frame to be not less than 38Kg. (Wt. of

cover 23 Kg.) and Wt. of frame 15Kg.) (R.C.C. top slabe with

1:2:4 mix (1- cement :2- coarse sand :4-graded stone aggregate

20mm size) foundation concrete 1:5:10 inside plaster 15mm

thick with cement mortar 1:3 finished smooth with a floating

coat of neat cement on walls and bed concrete etc. complete. (i)

Inside dimensions 455mmx 610mm and 450mm deep for single

pipe line.

[157] Providing and Fixing Heavy Duty Door Closer as directed by 43.00 No. 687.83

engineer in charge.

[158] Structural steel work (Confirming to IS 4923-1997) riveted, 1400.00 Kg 127.95

bolted or welded in builtup for all type sections, in framed

work, including cutting, hoisting, fixing in position and applying

a priming coat of approved steel primer all complete as per the

structural designs and directions of Engineer in charge.

[159] Providing and laying cement concrete work 1:1.5:3 (1-Cement : 1.90 Cu.m 6689.20

1.5- Coarse sand : 3- graded stone aggregates 20 mm nominal

size) and curing complete including cost of formwork and

reinforcement for reinforced concrete work in Superstructure

[160] Providing and fixing wooden panneling made of framing the 23.20 Sqm 5252.00

skeleton (plywood frame structure) with 18mm + 18mm thick

MR grade plywood for vertical and horizontal plywood (patti)

one side cover with 6mm thick MR grade plywood for grooving

as per design.Fixing properly without any air gap and finishing

with seletced 1.00 mm thick laminate.Before installation, make

hole/face plate for conduit pipes of eletcrical/networking

cables with openable stud from partition Including all materials

and labour etc. complete as per detail drawing and instruction

of engineer-in charge.

[161] Structural steel work (Confirming to IS 4923-1997) riveted, 2250.00 Kg 140.74

bolted or welded in builtup for all type sections, in framed

work, including cutting, hoisting, fixing in position and applying

a priming coat of approved steel primer all complete including

Consultancy Services (Structural desing Proof checking of

desing site Engineer Structure Engineer deployment etc.) Etc

Complete as directed by Engineer in charge .

Description of Item

(with brief specification and reference to book of Quantity Unit Rate Amount

specifications)

[162] Providing and fixing retro Reflective Hi Intensity Micro 13.50 Sqm 7610.66

Prismatic Grade Board using 2mm Aluminum / 4mm ACP, angle

iron 75 x 75 x 6mm. Descaling and degreasing the board as per

requirement using epoxy reflactive process by screen painting

as directed etc. complete including transporting and fixing in

C.C. 1:2:4 with necessary excavation curing etc. complete as per

I.R.C. 67-2012 design. A warranty for 7 years for the Retro

reflective sheeting from original manufacturer & a certified

copy of 3 year outdoor exposure test report from third party

test lab for the product offered shall be submitted by

contractor. (B) Class B Type-4 (MDR/ODR) retro reflective

[163] Excavation for foundation for depth from 1.5 m to 3.0 m 1.50 Cu.m 149.67

including sorting out and stacking of useful materials and

disposing off the excavated stuff upto 50 Meter lead. (B) Dense

or Hard soil

[164] Providing and laying cement concrete 1:4:8 (1- Cement : 4- 1.50 Cu.m 2658.40

Coarse sand : 8- Graded Brick bats aggregate 40mm normal

size) and curing complete excluding cost of formwork in (A)

Foundation and Plinth

[165] Repairing to Door / Window including dissembling from frame, 265.00 Sqm 589.78

wroughting, providing patti, angles, replacing / repairing

stoppers - aldrops - handles etc. for proper fixing in to frame

hole etc. complete for smooth operation and proper utilization

including assambeling and refixing of the same as directed by

Engineer-in-charge.

[166] Providing and laying Synroof High bond ecentromentric 589.85 Sqm 569.64

premium quality acrylic coating as a water proofing membrance

finished which consists of a coat of bitumine primer & 80 CSM

membrance in sunk slab, Terrace Slab with ulraviolet resistance

and working upto any height etc. complete as directed by

Engineer in charge

[167] Painting two coats on new steel and other metal surface with 60.00 Sqm 87.81

enamel paint, brushing, interior to give an even shade including

cleaning the surface an even shade including cleanicn the

surface of all dirt, dust and other foreign matter.

[168] Providing 15mm thick cement plaster in single coat on Rough 151.20 Sqm 196.15

(Similar) side of single or half brick walls for interior plastering

upto first Floor and finished even and smooth in (ii) Cement

mortar 1:4 (1-cement :4-sand)

[169] Distempering with dry distemper of approved brand and 1056.00 Sqm 68.73

manufacture (Three coats) and of required shade on wall

surfaces of given an even shade, over and including a priming

coat of whiting after thoroughly brooming the surface free from

mortar dropping and other foreign matter on Ceiling.

[170] Providing and fixing wsh down water closet (European type, 1.00 No. 1303.71

W.C. Pan) with integral P or S trap including jointing the trap

with soil pipe in Cement Mortar 1:1 (1-Cement : 1-fine sand)

(Seal and cover to be measured and paid for separately) (A)

vitreous China Pattern : (i) in white colour

[171] Providing and fixing washbasin with single hole for pillar tap 3.00 No. 1453.95

with C.I. or M.S. brackets painted white including sutting holes

and making good the same but excluding fittings. (A) Vitreous

China: (ii) Flat Back washbasin 550 mm x v 400mm size. (i) In

white colour.

Description of Item

(with brief specification and reference to book of Quantity Unit Rate Amount

specifications)

[172] Providing and fixing extruded aluminum window having 13.90 Sqm 2140.33

extruded aluminum Colour Powder Coated section frame main

outer size 127mm x 38.10mm x 1.35mm, @ Wt.1.384 Kg/mt,

horizontal Four track member size122.20mm x 31.75mm x

1.10mm @ Wt. 1.205 Kg/mt, vertical member of size 122.20mm

x 31.75mm x 1.50mm, @ Wt. 1.398 Kg/mt with sliding shutters

of horizontal member size 40mm x 18mm x 1.29mm @ wt.of

0.456Kg/mt, vertical member of size 40mm x 18mm x 1.29mm

@ wt.of 0.456Kg/mt, @ with 5 mm thick transparent bronze

colour tinted float glass with powder coated aluminum fittings

and fixtures and transparent silicon sealant glass fixing to frame

as per details etc complete for window.

[173] Providing PVC Flexible Waste Pipe 60cm Long and 25mm Dia. 50.00 No. 101.00

for Urinal as Directed by Engineer incharge.

[174] Carring out plinth treatment to post construction /existing 3450.00 Sqm 124.28

structure by spraying chemical solution for termite control

treatment including labour and material consistment with I.S.I

specification. Using Chlordene and Chiorpurfiles 20 EC. As Per

6131_paret-II Consentration Weight one percent is

recommended i.e one litre 20 EC chemical emulsion with

liter give 1 %concrentration inclusive of one litre chemical

emulsion appication at the rate of 5 Litre chemical / Sqm of

surface is recommended as per I.S

[175] Providing and fixing powder coated aluminum standard 87.00 Sqm 4568.43

extruded section glazed type Door of 63.50 mm x 38.10 mm x

1.95 mm or as specified drawing or as directed having Top &

bottom panel of 5 mm thick coloured float glass at top including

all fixtures and fastenings like glazing clips, rubber gasket,

hardware like handel, tower bolt, 6 liver mortise lock etc. and

labour etc. complete as directed by engineer in charge.

[176] Providing & Fixing Premium quality approved make like Jaquar 1.00 No. 18460.28

/ ESSCO or equivalent Wall Hung European type W.C. Pan with

in Built Jet, PP Soft closed seat cover, Hinges, Dual Flush cistern,

fixing accessary etc. complete of size 365 x 525 x 400 mm or

375 x 520 x 400 mm including cutting cutting holes and making

goods the same including labour, material, trasportation etc.

complete as directed by engineer incharge.

[177] Providing & Fixing Premium quality approved make like Jaquar 1.00 No. 13314.38

/ ESSCO or equivalent Table top wash basin of 565 x 425 x

mm with hole for pillar tap with C.I. or M.S. brackets painted

white including cutting cutting holes and making goods the

same include C.P. brass waste and waste pipes including labour,

material, trasportation etc. complete as directed by engineer

[178] Providing & Fixing Premium quality approved make like Jaquar 1.00 No. 6010.76

/ ESSCO or equivalent Urinal of size 355 x 340 x 535 mm

connecting with PVC waste pipe, Trap etc. complete including

labour, material, trasportation etc. complete as directed by

engineer incharge.

[179] Providing & Fixing Premium quality approved make like Jaquar 2.00 No. 3185.67

/ ESSCO or equivalent Bib cock with wall flange including

labour, material, trasportation etc. complete as directed by

engineer incharge.

[180] Providing & Fixing Premium quality approved make like Jaquar 3.00 No. 2365.04

/ ESSCO or equivalent Angular stop cock with wall flange

including labour, material, trasportation etc. complete as

directed by engineer incharge.

Description of Item

(with brief specification and reference to book of Quantity Unit Rate Amount

specifications)

[181] Providing & Fixing Premium quality approved make like Jaquar 1.00 No. 5846.01

/ ESSCO or equivalent Flush Valve dual flow 40 mm size having

Conceled body with Exposed shut of provision and 100 mm

square plate (3 to 6 liter per flushing) including labour,

material, trasportation etc. complete as directed by engineer

[182] Providing and fixing eco-friendly light weight calcium silicate 3.60 Sqm 1648.96

falseceiling tiles having Tegular edge & 15 mm Thick Densified

edgeson the Tile Periphery for Extra Strength The Light weight

calciumsilicate ceiling tiles shall have, light reflection 85% non-

combustible as per B.S. 476 part IV, 100% humidity resistance

andalso having thermal conductivity0.043° w/m KC.for the

bestthermal Insulation . The Light weight calcium Silicate tile

shall beof approved texture Fine fissured/ Spintone/Cosmos

having NRCvalue of 0.5 & Globe having NRC value of 0.75 NRC

or equivalentof size 595 X 595 mm to be laid on true horizontal

levelsuspended inter locking metal grid of hot dipped

galvanized steelsections (galvanizing @120 grams per sqm

including both side) consisting of main ‘T’ runner suitably

spaced at joints to getrequired length and size of 24X38mm

made from 0.30 mm thick (minimum) sheet, 1200mm centre to

centre, and cross ‘T’ of size24X28mm made out of 0.33mm

(Minimum) sheet spaced1200mm along spaced between main

‘T’ at 600mm centre tocentre to form agrid of 1200 X 600 mm

and secondary cross ’T’ oflength 600mm and size 24x28mm

made of 0.30 mm thick (Minimum) sheet to be interlocked at

middle of the 1200X600mmpanel to form grid of size

600X600mm resting on peripherywalls/ partitions on a

perimeter wall angle pre-coated steel of size (24X24X3000mm

made of 0.40mm thick (minimum) sheet withthe help of rawl

plugs at 450mm centre to centre with 25mm longdry wall

screws @ 230mm interval and laying 15mm thickDensified

edges light weight calcium silicate ceiling tiles ofapproved

texture (Fine Fissured/Cosmos/Spintone) in the gridincluding,

cutting /making opening for services like diffusers,

[183] Distempeing (Two coats) with oil bound distemper of approved 1450.00 Sq.m 71.90

brand and manufacture and of required shade on wall surfaces

to give an even shade, over and including a priming coat with

distemper primer of approved brand and manufacture after

thoroughly brushing the surface free from mortar dropping and

other foreign matter and also including preparing the surface

even and sand papered smooth.

[184] Box cutting the road surface to proper slope and camber for 40.00 Cu.m 104.20

making a base for road work including removing the excavated

stuff and depositing on the road side slope as directed upto

50Mt.lead.

[185] Providing and Fixing Pre-cast concrete kerb stone of gray 120.00 Rmt 384.96

cement based concrete block 30cm length 30cm height and

15cm thick of M200 grade concret as per approved design and

including excavation for fixing in proper line and level filling the

joint with CM 1:3 (1cement:3fine sand) etc complete.

Description of Item

(with brief specification and reference to book of Quantity Unit Rate Amount

specifications)

[186] Providing and Fixing 18 mm thick Plywood SHUTTER for 12.00 sqm 16152.01

Cupboard or Below platform shutter using 18mm thick

TERMITE PROOF PLY (GREENPLY OR EQUIVALENT) WITH

BOTH SIDE LAMINATE & WOODEN BEADING ON PERIPHERY,

Exposed face should be covered with 1.0 mm thick laminate of

approved quality and pattern, colour, texture the rest of the

inside surfaces, shelves ete, shall be finished with 0.80 mm

thick Sqm white laminates of approved make, wooden framing

shall be used including alround framing of 19 mm X 12 mm.

teak wood member at all borders and in the centre where ever,

all the sides of the shutter should be covered with teakwood

battens and provided with necessary framing, best quality SS

channels for sliding, SS finished hinges, hadles, megnet,

deadlock etc. as approved and directed by Engineer-In-Charge

[187] Providing and laying cement concrete 1:3:6 (1-Cement: 3- 20.00 Cu.m 3005.76

coarse sand: 6- hand broken stone aggregates 40 mmnominal

size) and curing complete excluding cost of formwork in (A)

Foundation and Plinth

[188] Providing and fixing pre-cast Rubber Dye / steel Dye inter 180.00 sqm 686.90

locking concrete block 60mm thick with grade of concrete M

300 pnumatic compressed vibrated mechanically and as per

approved design Confirming to IS 15658 2006 including 35 mm

Sand layer for levelling and filling the joint with sand in proper

line and level as per guidlines of IRC SP 63-2018 etc. Complete

[189] Applying two coats of two component dampproof coating of 740.00 sqm 295.63

approved brand and manufacture on undecorated wall surface

to give an even shade including throughly brushing the surface

free from mortar droppings and other foreign matter and sand

papered smooth as per instruction of Engineer In Charge

[190] Providing and erecting Approved make Ceiling fan with double 3.00 Each 1596.81

ball bearing ISI mark with condenser A.C. 230V.50 c/s.1200

mm. sweep complete, canopy erected on existing hook or clamp

with earthing. (Make shall be approved by Engineer in charge)

[191] Supplying & erecting approved make low noise decorative 3.00 Each 1703.87

exhaust fan having square frame ABS body with inbuilt lowers

& square frame. 200mm with 1350RPM Cat.II

[192] Providing following type of Modular Type Accessories mounted 8.00 Each 398.95

with PVC /metallic/Wooden box, single mounting base frame

covered with textured/metallic/ white front plate, modules

erected with necessary connections as per site situation

directed by Engineer In charge. (5) Electronic hum Free steps

EME Fan regulator, Cat.III

[193] Providing & erecting Switch board for Computer or electric 9.00 Each 1133.22

apparatus consisting of following modular type accessories

mounted with PVC /Metallic concealed /open box with single

mounting base frame covered with textured/metallic/white

front plate, modules erected with necessary connections as

1 no. 6A/16A universal plug-switch combined.

3 nos. 6A Switch

3 nos. 6A 5 pin Plug

For Modular Type Accessories, Catill

Description of Item

(with brief specification and reference to book of Quantity Unit Rate Amount

specifications)

[194] Supplying and erecting LED indoor fittings with LEDs of 7.00 Each 295.93

wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB, with

housing used as a heat sink shall be made of thick sheet Steel

conforming to IS: 513/CRCA/aluminium die cast powder coated

and high U.V. & corrosion resistance with diffuser with

company mark/name 160V to 270V, Power Factor more than

0.95, THD < 15%, CCT 3000 K to 6500K, Luminaire efficacy>

lumens/watt, LED driver efficiency > 85% (fitting required LM-

79 & LM-80 Certificates) (NOTE: Below description have shown

ranges of Wattage capacity of LED fittings. The Engineer

shown.) (A) Tube Light with integral driver (iii) 18-20 Watts,

Surge -2KV, IP-20, conventional 4 feet, Cat-III

Total Rs.

I/We am/are willing to carry out the work at…..........…% above/below percent (Should be written in

figures and words) of the estimated rate mentioned above. Amount of my /our tender works out as under.

Estimated amount put to tender Estimated amount put to tender

Deduct………% below Add………% Above

In words In words

1. The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-

In-Charge for which no extra payment shall be made.

2. The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3. GST and Income tax TDS will be deducted at a source while making payments of bills

4. In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-

10/2017 Cement Consumption/16/C Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where

there is a change as per actual mix design the cost of difference of cement consumption have been deducted

from the rate of original item at the rate of input rate mentioned in all the tender.

5. Credit of Dismantal Material amount of Rs. 165465.00 must be recovered from Contractor's R.A Bill.

6. Payment will be given only if the material testing result is satisfactory.Testing of material shall be done as per

statement attached with specification

Dated Signature Deputy Executive Engineer Executive Engineer

the Contractor. R & B Sub Division Kheda R & B Division

Nadiad Nadiad