SPECIAL REPAIR TO OTM ACCN BLDG NO. P366 AT PRC PROVN OF KITCHEN ROOM BLDG NO T21A SINGLE JCOs ACCN FOR JCOs MESS CLUB AT MH RAMGARH CANTT PROVN OF SHED AT SQUAD POST 3 TRAINING COMPANY LENGTH 08 METER x WIDTH 7 METER AND HEIGHT 5 METER AT 20 CAMP SR

Amount

Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in soft/ loose soil complete all as specified and directed.

Add to (or deduct from) above item for every 3cm or part there of above or below 15 cm average depth complete all as specified and directed.

Excavation in trenches in soft & loose soil not exceeding 1.5 metre deep and not exceeding 1.5 mtr width and getting out soil including forming bottom surface to required slope/gradient for laying cables/pipes,foundations, shafts, well, cesspits, manholes etc. complete all as specified and directed.

Returning, filling in including spreading, leveling, watering and well ramming in layers of not exceeding 25 cm thick after the cables & pipes etc. are laid, jointed & tested and foundations complete all as specified and directed by Engineer-in-Charge.

Removal of surplus excavated spoil not exceeding 50 Mtr distance and depositing where directed by Engineer-in-Charge at a level not exceeding 1.5 m above the starting point complete all as specified.

Removal of surplus excavated spoil exceeding 250 mtr but not exceeding 500 mtr distance and depositing where directed by Engineer-in-Charge at a level not exceeding 1.5 m above the starting point complete all as specified.

M&L for plain cement concrete 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in sub base of flooring, foundations,filling & mass concrete etc complete all as specified and directed.

M&L reinforced cement concrete 1:2:4 ( M-15)(using 20 mm graded crushed stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. Note : Reinforcement & form work will be measured & paid seperately under respective item of BOQ.

M&L reinforced cement concrete 1:2:4(M-15) (using 20 mm graded crushed stone aggregate) as in lintels, beam, floor/roof Beams, cantilevers, bressummers, , etc complete all as specified and directed. Note : Reinforcement & form work will be measured & paid seperately under respective item of BOQ.

M&L reinforced cement concrete 1:2:4 (M-15)(using 20 mm graded crushed stone aggregate) as in chajja etc complete all as specified and directed. Note : Reinforcement & form work will be measured & paid seperately under respective item of BOQ.

Use and waste of form work to sides of soffit of chajja,chullah hoods,troughs & similar items etc including for rough finished surface of concrete complete all as specified and directed.

Use and waste of form work to sides of soffit of suspended slab such as roof slab ,floor slab ,landing and similar work , not exceeding 200 mm thick for rough finished surface of concrete complete all as specified and directed.

Use and waste of form work to sides and soffit of lintel ,Beam,floor/roof Beams, etc for rough finished surface of concrete complete all as specified and directed.

Use and waste of form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor & roofs and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exceeding 10cm but not exceeding 20cm wide rough finished surface of concrete complete all as specified and directed.

M&L for Brick work using old size sub class "B" bricks , straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 etc complete all as specified & directed.

M&L for half brick thick Brick work using old size sub class "B" bricks , straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:4 etc complete all as specified & directed.

M & L for 50 mm thick damp proof course PCC (1:1.5:3) type B-0 (using 12.5 mm graded crushed stone aggregate )mixed with integral water proofing compound (as per manufacturer’s instructions) or @ 3% by weight of cement)conforming to IS: 2695 over 150 micron thick polythene film complete all as specified & directed. (Note:Water proofing compound shall be measured and paid seprerately under respective item of "BoQ")

M&L for mild steel TMT bars 10mm dia and over grade Fe-500, cut to length, bent to shape required, including cranking bending spirally for hooping for column,, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete etc all as specified and directed.

M&L for mild steel TMT bars 08 mm dia and over grade Fe -500 , as in stirrups, spacers & binders ,cut to length, bent to shape required, including cranking bending spirally for hooping for column,, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete etc all as specified and directed.

M&L for rendering 10 mm thick on brick masonry/concrete surface etc in CM (1:6) surface finished even & smooth using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick on other than fair face brick masonry/concrete surface etc in CM (1:4) surface finished even & smooth using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick on fair face brick masonry/concrete surface etc in CM (1:6) surface finished even & smooth without using extra cement complete all as specified and directed.

M&L for rendering 10 mm thick on brick masonry/concrete surface etc in CM (1:4) surface finished even & smooth using extra cement complete all as specified and directed.

M & L for rendering 5 mm thick in CM 1:3 on concrete surfaces as in ceiling finished even and fair complete all as specified and directed.

M&L for preparation of newly plaster surface of wall using sand paper and applying two coats of cement base paint over a coat of alkali primer including necessary scaffolding complete all as specified & as directed.

M&L for preparation of newely plastered surfaces of wall and applying three coats of white wash on wall complete all as specified & directed.

M&L for preparation of newely plastered surfaces of ceiling and applying three coat of white wash on ceiling ,chajjas,facia etc. surface complete all as specified & directed.

M&L for 100 mm thick plain cement concrete 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) as in sub base to flooring/hard standing etc ,complete all as specified and directed.

M & L for 75 mm thick plain cement concrete (1:3:6) mix, type C-1 (using 20mm graded crushed stone aggregate ) as in plinth protection, finishing the surfaces even and fair without using extra cement, including 10 mm wide, 75mm deep joints made at 3.00 m in length and filled with bitumen 85/25 grade and sand in the ratio 1:3 including necessary form work , complete all as specified and directed.

M&L for hard core of broken stone or boulder gauge not exceeding 63mm deposited, spread & leveled in layers not exceeding 15cm thick, watered and rammed to a true surface etc complete all as specified& directed.

M&L for 25 mm thick plain cement concrete 1:2:4,type B-1(using 20 mm graded crushed stone aggregate) as in floor /hardstanding etc & surface finished even and smooth without using extra cement complete all as specified & directed.

M & L joint free non skid coloured ceramic tiles 7 to 8 mm thick (sqaure/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc., over and including 15mm thick screed bed in cement mortar (1:4) ,set and jointed in neat cement slurry and pointed in coloured cement to match the existing surfaces,complete all as specified and directed.

M & L glazed ceramic coloured tiles of size 375 mm x 250 mm x 7mm/450 mm x 300 mm x7 mm thick ,as in dado/skirting etc ,set and jointed in neat cement slurry and pointed in colour cement to match the tiles ,over & including 10 mm thick rendering in cement plaster in CM (1:4), complete all as specified and directed.

S&F for 1.25 mm thick pressed steel frames of size 165mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc including plain cement concrete 1:3:6, type C-0 (using 12.5 mm graded crushed stone aggregate) as in filling in pressed steel door complete all as specified and directed. Note: The quoted unit rate under this item shall deemed to be included one shop coat of primer.

S & F 35 mm thick, factory made, IInd class hard wood plain framed panelled door shutter (two panel) with lock rail and panel of 9 mm BWP commercial ply . The size of rail and stile as per IS : 1003 (part-I) kiln seasoned and chemically pressure treated complete all as specified and directed .

S & F 35 mm thick, factory made, IInd class hard wood glazed and skeleton shutters open rebated and prepared to receive glass, gauze, etc. (divided into squares with plain, chamfered or rounded, mitred and rebated sash bars any number size of members), beads for securing glass, etc., sizes of members of shutters as specified in SSR Part I, Section 8 clause 8.24 (a); kiln seasoned & chemically pressure treated etc complete all as specified and directed . (Note:- (i)Glass / wire cloth shall be measured & paid separately.(ii) Sample of shutter in sample room of GE office.)

M & L for 40mm thick (measured solid),providing precast cement concrete 1:2:4 ,type B-0 ( using 12.5 mm graded crushed stone aggregate ) as in louvres and jallies, including all mould- ings but excluding frame including setting in cement mortar 1:4 including necessary formwork etc complete all as specified and directed.

S&F 150 mm long aluminium anodised door stopper with rubber shoe complete all as specified and directed.

S & F 100mm size butt hinges medium weight cold rolled mild steel complete all as specified and directed .

S&F 150mm aluminium alloy handles, cast type, anodised complete all as specified & directed.

S&F 125mm aluminium alloy handles, cast type, anodised complete all as specified & directed.

S&F 200 mm long aluminium anodised barrel tower bolts of extruded section and fixed all as specified and directed.

S&F 300mm long aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

M&L plain cement concrete 1:3:6, type C-1 (using 20 mm graded crushed stone aggregate) in for inserting hold fast of doors & window & similar work etc. including necessary form work complete all as specified and directed

S&F rotational moulded polythene water storage tank of capacity 500 ltrs (Cylindrical/vertical with closed type), triple layer construction, ISI marked, hoisted and fixed in position including 20 mm bore GI nipple and 20 mm bore ball/ float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 210 gms)complete all as specified and directed.

S&F rotational moulded polythene water storage tank of capacity 2000 ltrs (Cylindrical/vertical with closed type), triple layer construction, ISI marked, hoisted and fixed in position including 20 mm bore GI nipple and 20 mm bore ball/ float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 210 gms) including taking down of existing tank complete all as specified and directed.

Disconnecting existing water tanks of capacity exceeding 500 Ltr but not exceeding 1000 Ltr, setting aside (or lowering, if required) for repairs, cleaning, etc.,and hoisting, if required for reconnecting and re-fixing in position complete all as specified and directed.

M&L for plain cement concrete 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) as in base of PVC tank etc including necessary form work complete all as specified and directed.

Taking up or down steel tubing and connections of 15 mm bore or removal to store complete etc and making good the surface in cement mortar 1:3 complete all as specified & directed.all as specified & directed.

Taking up or down steel tubing and connections of 20 mm bore or removal to store complete etc and making good the surface in cement mortar 1:3 complete all as specified & directed.all as specified & directed.

Taking up or down steel tubing and connections of 25 mm bore or removal to store complete etc and making good the surface in cement mortar 1:3 complete all as specified & directed.all as specified & directed.

Refixing for 15 mm bore old steel tubing and connections in new or old position (Walls, ceiling,floors, etc.)complete all as specified & directed.all as specified & directed.

Refixing for 20 mm bore old steel tubing and connections in new or old position (Walls, ceiling,floors, etc.)complete all as specified & directed.all as specified & directed.

Refixing for 25 mm bore old steel tubing and connections in new or old position (Walls, ceiling,floors, etc.)complete all as specified & directed.all as specified & directed.

S&F for GI water tubing medium grade, ISI marked, galvanised, 15 mm bore with all fittings, (such as tee, elbow, socket, union & short pieces) fixed to walls and ceiling or laid in floors including cutting chases for brick walls and making good the surface in cement mortar 1:3 complete all as specified & directed.

S&F for GI water tubing medium grade, ISI marked, galvanised, 20 mm bore with all fittings, (such as tee, elbow, socket, union & short pieces) fixed to walls /laid in trenches and ceiling or laid in floors including cutting chases for brick walls and making good the surface in cement mortar 1:3 complete all as specified & directed.

S&F for GI water tubing medium grade, ISI marked, galvanised, 25 mm bore with all fittings, (such as tee, elbow, socket, union & short pieces) fixed to walls /laid in trenches and ceiling or laid in floors including cutting chases for brick walls and making good the surface in cement mortar 1:3 complete all as specified & directed.

S&F angle stop valve cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends of size 20 mm bore complete all as specified & directed.

S&F in repair angle cock cast copper alloy fancy type,chromium plated with long shank screwed down high pressure with crutch or butterfly handle screwed both ends of size 20 mm bore complete all as specified & directed.

S&F stop cock 15mm bore chromium plated fancy type,cast copper alloy, screwed down high pressure, screwed both ends for iron pipe or for brass ferrule fixed concealed in wall with CP wall cap etc complete all as specified and directed.

S & F vitreous China wash basin, any colour, flat back size 550 mm X 400mm including 32mm brass chromium plated waste coupling ,PVC 32 mm bore waste pipe, chromium plated Grating including bracket,fixing of pillar tap & PCC 1:2:4 ,type B-1(using 20 mm graded crushed stone aggregate) for embedding brackets & making good disturbed surface with CM 1:3 complete all as specified and directed. Note : Pillar tap as supply only will be measured & paid seperately under respective item of BOQ.

S & F in repair vitreous China wash basin, any colour, flat back size 550 mm X 400mm including 32mm brass chromium plated waste coupling ,PVC 32 mm bore waste pipe, chromium plated Grating including bracket,& PCC 1:2:4 ,type B-1(using 20 mm graded crushed stone aggregate) for embedding brackets & making good disturbed surface with CM 1:3 complete all as specified and directed.

Supply only pillar taps fancy type, cast copper alloy with capstan head, chromium plated, screwed down with or without lettered 'Hot' or 'Cold' with long screw shanks and fly nuts, screwed for iron pipe and fixed for 15 mm bore complete all as specified & directed.

S & F in repair pillar taps long body chromium plated, cast copper alloy with capstan head, chromium plated, screwed down with or without lettered 'Hot' or 'Cold' with long screw shanks and fly nuts, screwed for iron pipe and fixed for 15 mm bore complete all as specified & directed.

S&F in repair stop valve 15mm bore chromium plated fancy type cast copper alloy, screwed down high pressure, screwed both ends for iron pipe or for brass ferrule fixed concealed in wall etc complete all as specified and directed.

S&F bib taps , cast copper alloy with capstan head or butter fly handle,chromium plated , fancy type screwed down with high pressure screwed for iron pipe and fixed 15 mm bore complete all as specified & directed.

S&F brass chromium plated shower rose with swivel joints, 125 mm size in square with CP long shank arm including fixing to steel pipe or union complete all as specifed & as directed.

S&F towel rail brass chromium plated towel rail , 20 mm dia ,D-type 600 mm long between flanges fixed with and including chromium plated brass screw & wooden /plastic cleats complete set all as specified and directed.

S&F in repair for PVC connection 15 mm dia size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F 75 mm bore PVC(SWR) pipes single socketed , in any length with rubber ring joints, laid in trenches ,floor or in wall complete all as specified and directed.

S&F 110 mm bore PVC(SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches ,floor complete all as specified and directed.

S&F in repair 110 mm bore PVC(SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches ,floor complete all as specified and directed.

S&F in repair 110mm bore PVC(SWR) pipes single socketed, in any length with rubber ring joints, fixed on wall including PVC clamp properly with PCC 1:2:4 complete all as specified and directed

S&F 110 mm bore PVC(SWR) pipes single socketed, in any length with rubber ring joints, fixed on wall including PVC clamp properly with PCC 1:2:4 complete all as specified and directed

S&F 75 mm bore PVC(SWR) pipes single socketed, in any length with rubber ring joints, fixed on wall including PVC clamp properly with PCC 1:2:4 complete all as specified and directed

S&F in repair 75 mm bore PVC(SWR) pipes single socketed, in any length with rubber ring joints, fixed on wall including PVC clamp properly with PCC 1:2:4 complete all as specified and directed

S&F in repair 75 mm bore PVC(SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches ,floor complete all as specified and directed.

S&F 75 mm PVC(SWR) bends any radius complete all as specified and directed.

S&F in repair 75 mm PVC(SWR) bends any radius complete all as specified and directed.

S&F 110 mm PVC(SWR) bends any radius complete all as specified and directed.

S&F in repair 110 mm PVC(SWR) bends any radius complete all as specified and directed.

S&F in repair 110mm PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

S&F in repair 75 mm PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

S&F 110mm PVC (SWR) junction double, (double T) equal or unequal complete all as specified and directed.

S&F 75mm PVC (SWR) junction double, (double T) equal or unequal complete all as specified and directed.

S&F 110 mm PVC (SWR) vent cowl complete all as specified and directed.

M&L for 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement with chromium plated grating with or without hole complete all as specified and directed.

M&L for 18 to 20 mm thick granite of approved type / variety (table rubbed and pre mirror polished) in window cill, jambs, steps, and cooking platforms including pointing in coloured cement to match with shade of granite including half moulding of granite edges, over & including 20 mm thick screed bed in CM(1:4) for laying of granite slab etc complete all as specifed and as directed.

S&F kitchen sinks made of stainless steel 1.00 mm thick sheet with plugs, washers & waste coupling and waste pipe, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495 mm X 420 mm bowl size 410 mm X 330 mm X 160 mm including 40 mm bore PVC flexible waste/flush pipe 800mm long with socket fixed with sink brass waste coupling complete all as specified and directed.

M&L for 18/19 mm thick block boards, grade 2 quality, i n t e r i o r grade, commercial type for cup board shutter,shelf etc, fixed with screws to timber frame-work complete all as specified and directed.

S & F for 30 mm width of flaps (when open) continuous (piano) hinges,mild steel, bright finish or electrogalvanised complete all as specified and directed.

S & F ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and directed.

S&F 40mm dia, brass ,cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified and directed.

S&F mild steel 200 mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified & directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples etc complete all as specified & directed.

S&F in repair stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples etc complete all as specified & directed.

S&F 3.0 mm thick frosted glass pin headed type in squares/ rectangular not exceeding 0.5 Sqm in each pane glazing with oil putty or aluminium frame/shutters with rubber neoprene beading complete etc all as specified & directed.

Hacking out old broken glass(any thickness, size, quality or description) from wooden frames/steel frames, glazed with oil putty or fixed with beads complete all as specified and directed

M & L for 3mm thick plain sheet glass ordinary quality and glazing with oil putty not exceeding 0.50 Sqm in each pane,complete all as specified and as directed by Engr-in-Charge .

S&F small fitings of 2nd class hard wood such as brackets of any type, latch and hinge block shape door, window stops and the like including all necessary labours articles not exceeding 200 cu.cm each complete all as specified and as directed by Engr-in-Charge .

S&F steel window with side hung shutters including box type hinges with steel handles and steel peg stay complete with glazing bars, dovetailed or welded with four Nos mild steel flat iron 25 mm X 3mm ,200 mm length (appx)& two Nos mild steel tower bolt 300 mm long and one peg stay on each leaf complete all as specified and directed

S&F steel window with side hung shutters including box type hinges with steel handles and steel peg stay complete without glazing bars, dovetailed or welded with four Nos mild steel flat iron 25 mm X 3mm ,200 mm length (appx)& two Nos mild steel tower bolt 300 mm long and one peg stay on each leaf complete all as specified and directed

S&F steel ventilator box type hinges with steel handles and steel peg stay complete with glazing bars, dovetailed or welded complete all as specified and directed

M&L for framed work such as grills,gratings etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railing; framework of water tanks and similar work conforming to Fe 290- Gde E -165 & for portions framed and hung as gates, including pintle hinges, stops,hand-made sliding bolts, etc.complete all as specified and as directed

M&L for prepartion of new or previously untreated steel surface of any description , not otherwise described over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified & directed.

Taking down existing roof treatment any thickness including mud phuska, plastering, leaping plaster of any thickness cuting & up rooting tree roots/Vegitable growth & removing the debris from the premises upto 500m from the MOD land including cleaning/washing down and keeping surfaces clean complete all as specified and as directed.

M & L for brushing neat cement slurry (@ 3 Kg of cement per Sqm) mixed with water proofing compound in the proportion ,water proofing compound, water and cement (1:4:7) or as per manufacturer's instructions for bonding of old concrete surface to new concrete, complete all as specified and as directed.(Note:Water proofing compound shall be measured and paid seprerately under respective item of "BoQ")

M & L for PCC (1:2:4) ,type B-0 (using 12.5mm graded crushed stone aggregate) mixed with integral water proofing chemical compound, mixed in proportion 200 milli litre per 50 Kg of cement as in padding, benching, sunken portion etc., on roof surface for correcting/making proper slope on roof, etc.,complete all as specified and directed.

M & L for cutting 75 mm wide and 65 deep in brick wall/PCC block/RCC surface any location shaping horizontal face groove filled with PCC (1:2:4) type B-0 (using 12.5mm graded crushed stone aggregate) with and including chemical compound mixed in proportion 200 mili litre per 50 Kg of cement or as per manufacturer's instructions laid when concrete is still green, complete all as specified and as directed.(Note:Water proofing compound will be measured and paid seprerately under respective item of "BoQ")

M & L for rendering 10mm thick in CM (1:4) on concrete/brick surfaces with liquid water proofing compound @ 200 ml/50 Kg of cement or as per manufacturer's instructions finished even and smooth without using extra cement over roof/sunken slab/wall , complete all as specified and as directed.(Note:Water proofing compound will be measured and paid seprerately under respective item of "BoQ")

M & L for application of water proofing treatment using APP modified roof membrane over non accessible/ non approachable RCC roof slab / chajjah / canopy / parapet wall( horizontal/vertical surface)to be executed through approved applicator of the membrane manufacturer/authorized applicator of the manufacturer with following specification etc complete all as specified and directed :- (a) Cleaning existing surface properly. (b) Applying approved bituminous based primer( conforming to IS: 3384-1995) @ 0.30 litre / Sqm manufactured by the same agency as that of APP membrane with a density 0.87-0.89 Kg per liter at 25 degree centigrade on prepared surface & hot blown grade bituminen 85/25 @ 1.2 Kg/Sqm over primer . (c) Laying not less than 3mm thick APP (Atactic polypropylene Polymer modified prefabricated membrane) modified water proofing membrane weighing not less than 3.00 Kg/Sqm reinforced with non woven polyster fiber weight not less than 160gsm/Sqm using butane torch by torch application with 10cm side laps and 15cm end lap. Physical property of membrane shall be as under :- (i) Membrane weight not less than 3.00 Kg/Sqm. (ii) Non woven polyester weight not less than 160 gms/Sqm. (iii) Softening point of membrane not less than 150 degree Celsius. (iv) Joint tensile strength-longitudinal not less than 150 Kg / Sqcm and transverse not less than 450 Kg /Sq.cm at 230 degree Celsius. (v) Tear strength - longitudinal not less than 300 N & transverse not less than 250N. (vi) Elongation of reinforcement not less than 30%. (vii) Impermeability under water pressure not less than 3 Kg/Sqcm. (d) APP modified polymeric membrane shall be laid using butane torch by Torch application with minimum 10cm side overlap and 15cm end lap. (e) Applying two coat of bituminious based Aluminium Paint @ 0.3 Kg /sqm over APP Membrane.

M & L for roof treatment with following specifications:- (a) Cleaning existing surface properly. (b) Applying approved bituminous based primer( conforming to IS: 3384-1995) @ 0.30 litre / Sqm manufactured by the same agency as that of APP membrane with a density 0.87-0.89 Kg per liter at 25 degree centigrade on prepared surface & hot blown grade bituminen 85/25 @ 1.2 Kg/Sqm over primer . (c) Laying not less than 3mm thick APP (Atactic polypropylene Polymer modified prefabricated membrane) modified water proofing membrane weighing not less than 3.00 Kg/Sqm reinforced with non woven polyster fiber weight not less than 160gsm/Sqm using butane torch by torch application with 10cm side laps and 15cm end lap. Physical property of membrane shall be as under :- (i) Membrane weight not less than 3.00 Kg/Sqm. (ii) Non woven polyester weight not less than 160 gms/Sqm. (iii) Softening point of membrane not less than 150 degree Celsius. (iv) Joint tensile strength-longitudinal not less than 150 Kg / Sqcm and transverse not less than 450 Kg /Sq.cm at 230 degree Celsius. (v) Tear strength - longitudinal not less than 300 N & transverse not less than 250N. (vi) Elongation of reinforcement not less than 30%. (vii) Impermeability under water pressure not less than 3 Kg/Sqcm. (d) APP modified polymeric membrane shall be laid using butane torch by Torch application with minimum 10cm side overlap and 15cm end lap.

M& L for applying evenlya tack coat of industrial hot blown grade bituminen 85/25 @ 1.2 Kg/Sqm complete all as specified & directed.

M & L cement concrete tiles 25cmX25cm X 22mm thick set, jointed and pointed in neat cement slurry with grey cement and pigment in floors over and including 20 mm thick cement screed bed in cement mortar (1:4) complete all as specified & directed.

Supply only liquid water proofing compound complete all as specified and directed.

M&L for plain cement concrete 1:2:4, type B-1 (using 20 mm graded crushed stone aggregates) as in kerb/benching/copings including weathering, slightly rounded or chamfered angle and throating including use & waste of necessary form work etc complete all as specified and directed

S & F 50 mm bore GI tube, light grade as in spout pipe, complete with all fittings laid as in floor etc., complete all as specified and as directed.

M&L for demolition of cement concrete (un reinforced)in ground floor, terrazo tiles floor & paving of not exceeding 15cm thickness (above or below ground level )by mechanical tools and removing excavated material outside of MoD land, complete all as directed by Engr-in-Charge.

M&L for demolition of cement concrete (un reinforced)in ground floor , terrazo tiles floor & paving of exceeding 15cm thickness (above or below ground level )by mechanical tools and removing excavated material outside of MoD land, complete all as directed by Engr-in-Charge.

Dismantling, floor, hearth or wall tiling including cement mortar bedding complete and removing rubbish off from the premises complete all as specified and directed.

M&L for machine cut kota stone slab flooring 18mm -20 mm thick of size not less than 575 mm X 575 mm, over laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing & polishing over & including 20 mm thick screed bed in CM (1:6) complete all as specifed & directed.

M&L for machine cut kota stone slab in skirtings,riser of steps ,dado & pillar 10 to 12 mm thick laid and jointed with grey cement slurry pointed with cloured cement to match the shade of the slab including grinding rubbing & polishing over 10 mm thick backing coat in CM (1:4) etc complete all as specifed & directed.

M & L for machine cut kota stone slab flooring 40-50mm thick, laid over 20mm screed bed in cement mortar (1:4) as in step tread in one piece in one step, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M & L for rounding of edges of Kota/Cuddapah stone slab one edge, such as in steps, cooking platform and other similar work, complete all as specified and as directed.

Taking down chowkats or frames with shutters not exceeding 1.5 Sqm each (without taking off shutters from the frames) etc including builders hardware etc complete all as specified & directed .

Taking down chowkats or frames with shutters exceeding 1.5 Sqm but not exceeding 4 Sqm each (without taking off shutters from the frames) including builders hardware etc complete all as specified & directed.

Taking shutters of any description exceeding 1.00 Sqm but not exceeding 2.0 Sq m each, and removing from site, complete all as specified and directed by Engr-In-Charge .

Refixing of shutter of any description exceeding 1.00 Sqm but not exceeding 2.0 Sq m in same opening, complete all as specified and as directed.

S & F solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tubes suppyling & fixing in opening as per specification & drawing complete all as spcefied and directed by Engr-in-Charge .

S & F for factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS framed shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail &bottom rail on either side & as gap insert for top rail & bottom rail, paneling of plain colour PVC sheet to be fitted in the MS framed welded/sealed to stiles & rails with suitable PVC sheet beading & joined together with solvent cement complete all as fixing in the frame at site as per specification and drawing including 3 Nos stainless steel butt hinges 100 mm long for each door, complete all as specified and as directed.

S&F for 1.25 mm thick pressed steel frames of size 125mm x 60 mm forsingle or double doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc including plain cement concrete 1:3:6, type C-0 (using 12.5 mm graded crushed stone aggregate) as in filling in pressed steel door complete all as specified and directed. Note: The quoted unit rate under this item shall deemed to be included one shop coat of primer.

S & F 35 mm thick, factory made, IInd class hard wood glazed and skeleton shutters open rebated and prepared to receive glass, gauze, etc. (divided into squares with plain, chamfered or rounded, mitred and rebated sash bars any number size of members), beads for securing glass, etc., sizes of members of shutters as specified in SSR Part I, Section 8 clause 8.24 (a); kiln seasoned & chemically pressure treated etc complete all as specified and directed . Note:- (i)Glass / wire cloth shall be measured & paid separately. (ii) Sample of shutter in sample room of GE office.

M&L plain cement concrete 1:3:6, type C-1 (using 20 mm graded crushed stone aggregate) in for inserting hold fast of doors & window & similar work etc.including necessary form work complete all as specified and directed

M & L for preparation of new wooden of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

S&F in repair Harrison rails, anodised aluminium alloy with bracket etc., complete all as specified and as directed by Engr-in-Charge.

Taking down cement plaster of brick or stone masonry etc including raking out joints , hacking for key & scrubbing down with water etc complete all as specified & directed.

Demolition of brick work of any description and in any position built in cement or cement lime mortar including all quoins, arches, pillars including segregation of serviceable bricks for reuse & removal of rubbish out off MOD land etc complete all as specified and directed.

M&L for rendering 15 mm thick on brick masonry/concrete surface etc in CM (1:4),mixed with water proofing compound , trowelled to fair finished even & smooth without using extra cement complete all as specified and directed. (Note:Water proofing compound shall be measured and paid seprerately under respective item of "BoQ")

M&L for preparation of newly plastered surface of wall and applying two coats of oil emulsion distemper over a coat of alkali resistance primer complete all as specified and directed.

M & L for PCC (1:5:10), type E-2 (using 40 mm graded brick aggregate) as in sunken portion, sub-base, etc., complete all as specified and as directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc complete all as specified and directed.

M & L for anti-fungal chequered cement concrete tiles 30cmX30cm X 22mm to 25mm thick, set ,jointed and pointed in neat cement slurry with grey cement and pigment in floors over and including 20mm thick cement screed bed in cement mortar (1:6) complete all as specified & directed.

Demolition of cement concrete reinforced as in chullah hoods, shelves, cover slab and platform, etc,including removal of rubbish out off MOD land etc complete all as specified and directed

M & L for RCC 1:2:4, type B-1(using 20 mm graded crushed stone aggregate) as in kitchen platform, shelves ,cover slab, etc. including necessary formwork, complete all as specified and as directed.

S & F in repair 15mm, concussive push button taps cast copper allow screwed down for iron pipe and fixed, complete all as specified and as directed.

S&F WC squatting pan " Orissa Pattern" of size 580 mm X 440 mm white with integral foot rest including cast iron "P" or "S" trap, front or back inlet and making connection to trap & to flushing cistern complete including taking down existing pan & making good disturbed surface complete all as specified & directed.

S&F vitreous China wash down water closet (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe), fixing seat cover including connection to drain (or outgoing pipe, and to flushing pipe & antisyphonage pipe etc with aluminium hinging device including taking down existing pan & making good disturbed surface complete all as specified & directed. Note : Plastic seat cover will be measured separately as Supply only as considered under respective items.

Supply only plastic water closet seat closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device complete all as specified and directed.

S & F in repair vitreous China bowl type (back to corner ) of size 465 x 355 x 265 mm urinals with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe)(back or corner wall type),complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets,flush pipe, grating and Union for discharge pipe etc.complete all as specified and as directed

S & F in repair PVC flushing cistern 10 ltr capacity valve less syphonic action type low level with and including ball valve float and handle, PVC flush pipe 32 mm bore & PVC connection 15 mm bore 450 mm long with PTMT nuts and brackets complete set & making good disturbed surface with CM 1:3 complete all as specified and directed.

S & F shelf of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight 300 gms), complete all as specified and as directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc., and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting n.exc 10 cm girth in brick wall complete all as specified and as directed.

M&L for complete removal of existing treatment and preparation of plastered surface of wall and applying two coats of oil emulsion distemper over a coat of primer & a layer of putty (not less than 1.5 mm thick )complete all as specified and directed.

M & L for preparation of old decorated surfaces of ceiling including brooming down or steel wire brushing, scrapping down smokes soot moulds, moss and efflorescent salts and treating oil and greasy spot & applying one coat of oil bound distemper, complete all as specified and as directed.

M&L for preparing old decorated plastered surfaces of wall including cornices,pilastered etc. by brooming down or steel wire brushing, scraping down smoke soot, moulds, moss and efflorescent salt and trading oil and greasy spots and applying one coat of white wash complete all as specified and directed.

M&L for preparing old decorated plastered surfaces of ceiling including cornices,pilastered etc. by brooming down or steel wire brushing, scraping down smoke soot, moulds, moss and efflorescent salt and trading oil and greasy spots and applying one coat of white wash on ceiling surface complete all as specified and directed.

M & L for one coat of synthetic enamel paint to wooden surface exceeding 10cm width or girth including preparation of old painted wooden surfaces complete all as specified and directed.

M & L for preparation of old treated surfaces of steel of any description, not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint on steel surface complete all as specified and directed.

M&L for complete removal of existing treatment from walls (any number of layers) by scrapping with steel scrappers or any other means, including filling depressions of scrapped surfaces with preparation of plastered surfaces and preparation of surfaces of wall & applying two coats of cement based paint, over a coat of primer complete all as specified and as directed.

S & F 110 mm dia PVC(SWR) WC connector with lip ring, complete all as directed and as specified.

M&L for point wiring for one light/fan/exhaust fan point /exhaust fan/ bell /buzzer point controlled by one way switch with using with FRLSH PVC insulated PVC unsheathed electric cable conforming to IS:694, 1100V grade AC, single core having multi stranded copper conductor of size 1.5 Sq.mm nominal cross sectional area for phase & neutral and including non metallic rigid PVC conduit ISI marked medium grade not less than 20 mm dia with all conduit accessories in concealed wiring system & 1.5 Sqmm green PVC insulated unsheathed multistranded copper conductor as a earth wire connected to earth dolly by providing lugs including sunken type anodized pressed steel sheet terminal box made out of 1.6mm thick sheet of suitable size, for mounting fittings/junction boxes including board with bakelite sheet 2.8 mm thick laminated insulated sheet cover for housing/fixing switches etc., complete all as specified and directed. Note: Proper colour coding to be adopted.

All as per item No 162 here-in-before but 5 Amp socket outlet on same board.

All as per Srl item No.162 but one light point controlled by two, two way switches etc complete all as specified and directed..

All as per item No 162here-in-before but for 5 Amp switch socket on independent board.

M&L for point wiring with FRLSH PVC insulated PVC sheathed electric cable confirming to IS:694, 1100V grade AC, single core having multi stranded copper conductor of size 2.50 Sq.mm nominal cross sectional area for phase & neutral & including non metallic rigid PVC conduit ISI marked medium grade not less than 25 mm dia with all conduit accessories in concealed wiring system & 2.50 Sq.mm green PVC insulated unsheathed multistranded copper conductor as a earth wire connected to earth dolly by providing lugs including pressed steel anodized sunken boxes 60 mm deep made out of not less than 1.6 mm thick sheet cover with 2.80 mm thick laminated insulated sheet cover for housing/fixing switches etc.complete for one six pin switch socket outlet combination ,15 Amps & 5 amp socket point on independent board controlled by one ,one way switch complete all as specified and directed.

S & F switch piano flush button single pole one way 5 Amp/6 Amp, complete all as specified and as directed.

S & F socket outlet 2 in 1, 3 pin, 5Amp, flush type, universal, complete all as specified.

S & F Switch socket combination 2 in 1, 3 pin, 5Amp and 15 Amp flush type, universal, complete all as specified.

S & F Switch socket combination 2 in 1, 3 pin, 5Amp flush type, universal, complete all as specified.

S & F ceiling rose three terminals PVC/ Polycarbonate, isolated body complete all as specified.

S & F lamp holder, PVC/Polycarbonate type with back plate having matching colour to holder suitable for angle/batten fittings (ISI marked), complete all as specified.

S & F LED light fitting 1 x 20/22 watt , 220 V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose to fitting, complete all as specified and as directed by Engr-in-Charge. Make: Havells/Bajaj/Crompton Greaves/Phillips.

S&F 1X9 W/1X10 W watt LED Bulkhead fitting with IP 65 environmental frendly, ultra modern, energy saving mounted decorative oval bulk head edge lit LED luminaire comprising of high brightness LED 230 Volts AC circuit connecting up with three core flexible copper conductor cable of suitable size from ceiling rose to fitting, complete all as specified and as directed by Engr-in-Charge. Make: Havells/Bajaj/Crompton Greaves/Phillips.

S & F LED bulb of capacity 10 watt , lumen out put (1200)lm ,length 102 mm dia 56 mm , base cap B22 (ISI mark) complete all as specified and as directed by Engr-in-Charge. Make: Havells/Bajaj/Crompton Greaves/Phillips.

S & F steel body Ventil Air-DS type Exhaust fan of 450 mm sweep blade with louvers shutter , frame single phase ,230 V,50 Hz,1200 RPM AC ,copper winding , including provision of hole, mounting frame, nut, bolts, washer, fasteners etc and connecting exhaust fan to ceiling rose including provision of three core flexible copper cable of size 1.5 Sqmm not less than 0.5 mtr long for connection complete all as specified & directed. Note:cost of making suitable size opening wall for fixing exhaust fan is deemed to be included in unit quoted rate by bidders.

S & F energy efficient steel body Ventil Air-DS type Exhaust fan of 300 mm sweep blade with louvers shutter,frame single phase ,230 V,50 Hz,1200 RPM AC ,copper winding , including provision of hole, mounting frame, nut, bolts, washer, fasteners etc and connecting exhaust fan to ceiling rose including provision of three core flexible copper cable of size 1.5 Sqmm not less than 0.5 mtr long for connection complete all as specified & directed. Note:cost of making suitable size opening wall for fixing exhaust fan is deemed to be included in unit quoted rate by bidders.

S & F sheet metal enclosures for DBs when MCBs to used single pole and neutral (SPN) double door 240 volts, 4 way with IP-43 IK-09 protection including 200 Amp bus bar and neutral link (ISI marked), complete all as specified and as directed.

S & F in repair sheet metal enclosures for DBs when MCBs to used single pole and neutral (SPN) double door 415 volts,12 way with IP-43 IK-09 protection including 200 Amp bus bar and neutral link (ISI marked), complete all as specified and as directed.

S & F in repair sheet metal enclosures for DBs when MCBs/MCCBs to used vertical tripple pole and neutral (VTPN) double door 415 volts,4 way with IP-43 IK-09 protection including 200 Amp bus bar and neutral link (ISI marked), complete all as specified and as directed.

S & F amp rating 240V, 10 kA 'C' Curve miniature circuit breaker (MCB) of single poles and neutral and current carrying capacity 32 Amp in the MCB DB complete with connection testing and commissioning all as specified and as directed. Make: IndoAsian or its equivalent make in Havells/Standard/L&T.

S&F miniature circuit breaker (MCB) SP 6 to 32 Amps ('C' Series) having current rating 10 KA complete all as specifed and as directed .

S & F 240V, 10 kA 'C' Curve miniature circuit breaker (MCB) of single poles and neutral and current carrying capacity 32 Amp in the MCB DB complete with connection testing and commissioning all as specified and as directed. Make: IndoAsian or its equivalent make in Havells/Standard/L&T.

S & F 240V, 10 kA 'C' Curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 Amp in the MCB DB complete with connection testing and commissioning all as specified and as directed. Make: IndoAsian or its equivalent make in Havells/Standard/L&T.

Supply, laying , jointing & testing LT under ground cable XLPE insulated, screened ,PVC bedded, galvanised steel strip or wire armoured, electric power cable ( heavy duty) with standard aluminium conductor , 1100 Volts grade of cross sectional area 35 Sq mm 2.0 core complete all as specified and directed.

Material & labour for sand filling with clean dry fine sand unwashed including gently punning around cables in trenches for cable protection complete all as specified and directed by Engineer-in-Charge. NOTE:- For measurement purpose punned thickness shall be considered as per clause 19.75 of SSR Part-I.

Supplying & Laying un-reinforced pre-cast flat concrete cable protection cover of class LV, type- 2, size 250 mm x 150mm x 40mm, factory made, complete all as specified and directed by the Engineer-in-Charge.

M & L Sub main wiring two single core 6.0 Sqmm PVC insulated FRLSH multistanderd copper conductor cable and one run of 6.0 Sqmm PVC insulated unsheathed FRLSH multi stranded copper conductor cable for earth wire drawn in & including concealed rigid non metallic PVC conduit medium grade with fittings (ISI marked) not less than 25 mm dia, complete and making good disturbed surface wall complete all as specified and as directed. Note : - 2 runs of 6.0 Sqmm cable and 1 run of earth wire 6.0 sqmm shall be measured as one unit length.

M & L Sub main wiring four single core 10.0 Sqmm PVC insulated FRLSH multistanderd copper conductor cable and two run of 6.0 Sqmm PVC insulated unsheathed FRLSH multi stranded copper conductor cable for earth wire drawn in & including concealed rigid non metallic PVC conduit medium grade with fittings (ISI marked) not less than 25 mm dia, complete and making good disturbed surface wall complete all as specified and as directed. Note : - Four runs of 10.0 Sqmm cable and two run of earth wire 6.0 sqmm shall be measured as one unit length.

M&L ,for earthing complete with galvanised steel earth plate electrode of size 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below ground level, connected to galvanised earth lead wire 4.00 mm dia by means of bolts, nuts check nuts & washers of galvanised iron or steel, protected by GI pipe 15 mm bore (light grade) and watering pipe 20 mm bore GI pipe (light grade) and PCC of chamber and coping shall in 1:3:6 type C-1 using 20 mm graded stone aggregate including excavation and earth work and removal of surplus soil and filling with black cotton soil upto ground level complete all as shown in electrical plate No 3 of SSR Pt-I, 2009 with CI cover 10mm thick of size 300x300mm with charcoal dust and common salt complete and earth lead connected to distribution board including testing complete all as specified and directed. Note : Earth test result to be submitted duly tested in presence of Engineer -in Charge.

S & F 25 mm bore GI tube, light grade for cable protection with all necessary fitting, complete with all fittings laid as in floor etc., complete all as specified and as directed.

S & F 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S & F in repair 25mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S & F in repair 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Taking down carefully unserveciable/damaged copper/aluminium surface (batten/coduit or casing caping) point wiring any length for light/fan/socket or power including unscrewing from board (fitting and fixture such as switches, sockets, ceiling rose, lamp holders, brackets, pendent, regulators, sockets ,light fittings etc) and removing material from site and making good to the disturbed surface to match with existing finish etc complete all as specified and directed.

Taking down ceiling fan/exhaust fan of any sweep after disconnecting all necessary electrical connections from ceiling rose to fan, fan blades and deposit to MES store yard of AGE E/M Ramgarh, complete all as specified and as directed.

S & F LED mirror type light fittings 1 x 10 watts with high out put diffuser 2 feet ,220 volt ,AC decorative type with driver holder & LED lamp and all other accessories duly pre wired and making connection with and including three core copper flexible wire from connector to ceiling rose not less than 1 mtr fixed on wall with plastic gutties complete all as specified & directed.

Labour only for refixing ceiling /exhaust fan of any sweep with replacement of unserveciable three core PVC insulated multistranded copper conductor cable of size 23/0.193 connecting fan to ceiling rose including over hauling the fan,painting of ceiling fan with synthetic enamel paint by spraying machine including filling cavities with filler after cleaning all dust etc complete all as specified & directed.Note :Ceiling fan/exhaust fan of any sweep obtained here-in-before item No. 196 of BOQ.

S & F MCCB, four pole 100 Amps,415 Volt current rating and ultimate breaking capacity lcu= 25 KA with adjustable overload setting and having thermal magnetic release and to be fixed in ditribution board complete all as specified and directed.

S & F electric water heater storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre BEE5 star rated complete with all connected accessories such as safety valve,thermostate, heating element,NRV,connection piece,stop valve ,water connection from tank to geyser etc complete all as specified and directed.

M/s Popatlal A Rathod

Paras Nath Singh

upadhyay engineers and consultant

Balaji Construction And Company